Abdessamad El Abbassi
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_dac.c
- Revision:
- 130:1dec54e4aec3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_dac.c Fri Mar 21 11:45:09 2014 +0000
@@ -0,0 +1,702 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_dac.c
+ * @author MCD Application Team
+ * @version V1.3.0
+ * @date 16-January-2014
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the Digital-to-Analog Converter (DAC) peripheral
+ * applicable only on STM32F051 and STM32F072 devices:
+ * + DAC channel configuration: trigger, output buffer, data format
+ * + DMA management
+ * + Interrupts and flags management
+ *
+ * @verbatim
+ *
+ ===============================================================================
+ ##### DAC Peripheral features #####
+ ===============================================================================
+ [..] The device integrates two 12-bit Digital Analog Converters refered as
+ DAC channel1 with DAC_OUT1 (PA4) and DAC_OUT2 (PA5) as outputs.
+
+ [..] Digital to Analog conversion can be non-triggered using DAC_Trigger_None
+ and DAC_OUTx is available once writing to DHRx register using
+ DAC_SetChannel1Data() or DAC_SetChannel2Data()
+
+ [..] Digital to Analog conversion can be triggered by:
+ (#) External event: EXTI Line 9 (any GPIOx_Pin9) using DAC_Trigger_Ext_IT9.
+ The used pin (GPIOx_Pin9) must be configured in input mode.
+
+ (#) Timers TRGO: TIM2, TIM3,TIM7, TIM6 and TIM15
+ (DAC_Trigger_T2_TRGO, DAC_Trigger_T3_TRGO...)
+ The timer TRGO event should be selected using TIM_SelectOutputTrigger()
+
+ (#) Software using DAC_Trigger_Software
+
+ [..] Each DAC integrates an output buffer that can be used to
+ reduce the output impedance, and to drive external loads directly
+ without having to add an external operational amplifier.
+ To enable the output buffer use
+ DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Enable;
+
+ [..] Refer to the device datasheet for more details about output impedance
+ value with and without output buffer.
+
+ [..] DAC wave generation feature
+ Both DAC channels can be used to generate
+ 1- Noise wave using DAC_WaveGeneration_Noise
+ 2- Triangle wave using DAC_WaveGeneration_Triangle
+
+ [..] The DAC data format can be:
+ (#) 8-bit right alignment using DAC_Align_8b_R
+ (#) 12-bit left alignment using DAC_Align_12b_L
+ (#) 12-bit right alignment using DAC_Align_12b_R
+
+ [..] The analog output voltage on each DAC channel pin is determined
+ by the following equation: DAC_OUTx = VREF+ * DOR / 4095
+ with DOR is the Data Output Register
+ VEF+ is the input voltage reference (refer to the device datasheet)
+ e.g. To set DAC_OUT1 to 0.7V, use
+ DAC_SetChannel1Data(DAC_Align_12b_R, 868);
+ Assuming that VREF+ = 3.3, DAC_OUT1 = (3.3 * 868) / 4095 = 0.7V
+
+ [..] A DMA1 request can be generated when an external trigger (but not
+ a software trigger) occurs if DMA1 requests are enabled using
+ DAC_DMACmd()
+ DMA1 requests are mapped as following:
+ (+) DAC channel1 is mapped on DMA1 channel3 which must be already
+ configured
+ (+) DAC channel2 is mapped on DMA1 channel4 which must be already
+ configured
+
+ ##### How to use this driver #####
+ ===============================================================================
+ [..]
+ (+) Enable DAC APB1 clock to get write access to DAC registers
+ using RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE)
+
+ (+) Configure DAC_OUTx (DAC_OUT1: PA4, DAC_OUT2: PA5) in analog mode
+ using GPIO_Init() function
+
+ (+) Configure the DAC channel using DAC_Init()
+
+ (+) Enable the DAC channel using DAC_Cmd()
+
+ @endverbatim
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_dac.h"
+
+/** @addtogroup STM32F0xx_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup DAC
+ * @brief DAC driver modules
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* CR register Mask */
+#define CR_CLEAR_MASK ((uint32_t)0x00000FFE) /* check the value of the mask */
+
+/* DAC Dual Channels SWTRIG masks */
+#define DUAL_SWTRIG_SET ((uint32_t)0x00000003) /*!< Only applicable for STM32F072 devices */
+#define DUAL_SWTRIG_RESET ((uint32_t)0xFFFFFFFC) /*!< Only applicable for STM32F072 devices */
+
+/* DHR registers offsets */
+#define DHR12R1_OFFSET ((uint32_t)0x00000008)
+#define DHR12R2_OFFSET ((uint32_t)0x00000014) /*!< Only applicable for STM32F072 devices */
+#define DHR12RD_OFFSET ((uint32_t)0x00000020) /*!< Only applicable for STM32F072 devices */
+
+/* DOR register offset */
+#define DOR_OFFSET ((uint32_t)0x0000002C)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup DAC_Private_Functions
+ * @{
+ */
+
+/** @defgroup DAC_Group1 DAC channels configuration
+ * @brief DAC channels configuration: trigger, output buffer, data format
+ *
+@verbatim
+ ===============================================================================
+ ##### DAC channels configuration: trigger, output buffer, data format #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the DAC peripheral registers to their default reset values.
+ * @param None
+ * @retval None
+ */
+void DAC_DeInit(void)
+{
+ /* Enable DAC reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, ENABLE);
+ /* Release DAC from reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_DAC, DISABLE);
+}
+
+/**
+ * @brief Initializes the DAC peripheral according to the specified parameters
+ * in the DAC_InitStruct.
+ * @param DAC_Channel: the selected DAC channel.
+ * This parameter can be:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_InitStruct: pointer to a DAC_InitTypeDef structure that contains
+ * the configuration information for the specified DAC channel.
+ * @retval None
+ */
+void DAC_Init(uint32_t DAC_Channel, DAC_InitTypeDef* DAC_InitStruct)
+{
+ uint32_t tmpreg1 = 0, tmpreg2 = 0;
+
+ /* Check the DAC parameters */
+ assert_param(IS_DAC_TRIGGER(DAC_InitStruct->DAC_Trigger));
+ assert_param(IS_DAC_GENERATE_WAVE(DAC_InitStruct->DAC_WaveGeneration));
+ assert_param(IS_DAC_LFSR_UNMASK_TRIANGLE_AMPLITUDE(DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude));
+ assert_param(IS_DAC_OUTPUT_BUFFER_STATE(DAC_InitStruct->DAC_OutputBuffer));
+
+/*---------------------------- DAC CR Configuration --------------------------*/
+ /* Get the DAC CR value */
+ tmpreg1 = DAC->CR;
+ /* Clear BOFFx, TENx, TSELx, WAVEx and MAMPx bits */
+ tmpreg1 &= ~(CR_CLEAR_MASK << DAC_Channel);
+ /* Configure for the selected DAC channel: buffer output, trigger,
+ wave generation, mask/amplitude for wave generation */
+ /* Set TSELx and TENx bits according to DAC_Trigger value */
+ /* Set WAVEx bits according to DAC_WaveGeneration value */
+ /* Set MAMPx bits according to DAC_LFSRUnmask_TriangleAmplitude value */
+ /* Set BOFFx bit according to DAC_OutputBuffer value */
+ tmpreg2 = (DAC_InitStruct->DAC_Trigger | DAC_InitStruct->DAC_WaveGeneration |
+ DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude | \
+ DAC_InitStruct->DAC_OutputBuffer);
+ /* Calculate CR register value depending on DAC_Channel */
+ tmpreg1 |= tmpreg2 << DAC_Channel;
+ /* Write to DAC CR */
+ DAC->CR = tmpreg1;
+}
+
+/**
+ * @brief Fills each DAC_InitStruct member with its default value.
+ * @param DAC_InitStruct: pointer to a DAC_InitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void DAC_StructInit(DAC_InitTypeDef* DAC_InitStruct)
+{
+/*--------------- Reset DAC init structure parameters values -----------------*/
+ /* Initialize the DAC_Trigger member */
+ DAC_InitStruct->DAC_Trigger = DAC_Trigger_None;
+
+ /* Initialize the DAC_WaveGeneration member */
+ DAC_InitStruct->DAC_WaveGeneration = DAC_WaveGeneration_None;
+
+ /* Initialize the DAC_LFSRUnmask_TriangleAmplitude member */
+ DAC_InitStruct->DAC_LFSRUnmask_TriangleAmplitude = DAC_LFSRUnmask_Bit0;
+
+ /* Initialize the DAC_OutputBuffer member */
+ DAC_InitStruct->DAC_OutputBuffer = DAC_OutputBuffer_Enable;
+}
+
+/**
+ * @brief Enables or disables the specified DAC channel.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param NewState: new state of the DAC channel.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note When the DAC channel is enabled the trigger source can no more be modified.
+ * @retval None
+ */
+void DAC_Cmd(uint32_t DAC_Channel, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected DAC channel */
+ DAC->CR |= (DAC_CR_EN1 << DAC_Channel);
+ }
+ else
+ {
+ /* Disable the selected DAC channel */
+ DAC->CR &= (~(DAC_CR_EN1 << DAC_Channel));
+ }
+}
+
+/**
+ * @brief Enables or disables the selected DAC channel software trigger.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param NewState: new state of the selected DAC channel software trigger.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void DAC_SoftwareTriggerCmd(uint32_t DAC_Channel, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable software trigger for the selected DAC channel */
+ DAC->SWTRIGR |= (uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4);
+ }
+ else
+ {
+ /* Disable software trigger for the selected DAC channel */
+ DAC->SWTRIGR &= ~((uint32_t)DAC_SWTRIGR_SWTRIG1 << (DAC_Channel >> 4));
+ }
+}
+
+/**
+ * @brief Enables or disables simultaneously the two DAC channels software triggers.
+ * This function is applicable only for STM32F072 devices.
+ * @param NewState: new state of the DAC channels software triggers.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void DAC_DualSoftwareTriggerCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable software trigger for both DAC channels */
+ DAC->SWTRIGR |= DUAL_SWTRIG_SET;
+ }
+ else
+ {
+ /* Disable software trigger for both DAC channels */
+ DAC->SWTRIGR &= DUAL_SWTRIG_RESET;
+ }
+}
+
+/**
+ * @brief Enables or disables the selected DAC channel wave generation.
+ * This function is applicable only for STM32F072 devices.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected
+ * @param DAC_Wave: specifies the wave type to enable or disable.
+ * This parameter can be:
+ * @arg DAC_Wave_Noise: noise wave generation
+ * @arg DAC_Wave_Triangle: triangle wave generation
+ * @param NewState: new state of the selected DAC channel wave generation.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void DAC_WaveGenerationCmd(uint32_t DAC_Channel, uint32_t DAC_Wave, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_DAC_WAVE(DAC_Wave));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected wave generation for the selected DAC channel */
+ DAC->CR |= DAC_Wave << DAC_Channel;
+ }
+ else
+ {
+ /* Disable the selected wave generation for the selected DAC channel */
+ DAC->CR &= ~(DAC_Wave << DAC_Channel);
+ }
+}
+
+/**
+ * @brief Set the specified data holding register value for DAC channel1.
+ * @param DAC_Align: Specifies the data alignment for DAC channel1.
+ * This parameter can be one of the following values:
+ * @arg DAC_Align_8b_R: 8bit right data alignment selected
+ * @arg DAC_Align_12b_L: 12bit left data alignment selected
+ * @arg DAC_Align_12b_R: 12bit right data alignment selected
+ * @param Data: Data to be loaded in the selected data holding register.
+ * @retval None
+ */
+void DAC_SetChannel1Data(uint32_t DAC_Align, uint16_t Data)
+{
+ __IO uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_DAC_ALIGN(DAC_Align));
+ assert_param(IS_DAC_DATA(Data));
+
+ tmp = (uint32_t)DAC_BASE;
+ tmp += DHR12R1_OFFSET + DAC_Align;
+
+ /* Set the DAC channel1 selected data holding register */
+ *(__IO uint32_t *) tmp = Data;
+}
+
+/**
+ * @brief Sets the specified data holding register value for DAC channel2.
+ * This function is applicable only for STM32F072 devices.
+ * @param DAC_Align: Specifies the data alignment for DAC channel2.
+ * This parameter can be:
+ * @arg DAC_Align_8b_R: 8bit right data alignment selected
+ * @arg DAC_Align_12b_L: 12bit left data alignment selected
+ * @arg DAC_Align_12b_R: 12bit right data alignment selected
+ * @param Data: Data to be loaded in the selected data holding register.
+ * @retval None
+ */
+void DAC_SetChannel2Data(uint32_t DAC_Align, uint16_t Data)
+{
+ __IO uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_DAC_ALIGN(DAC_Align));
+ assert_param(IS_DAC_DATA(Data));
+
+ tmp = (uint32_t)DAC_BASE;
+ tmp += DHR12R2_OFFSET + DAC_Align;
+
+ /* Set the DAC channel2 selected data holding register */
+ *(__IO uint32_t *)tmp = Data;
+}
+
+/**
+ * @brief Sets the specified data holding register value for dual channel DAC.
+ * This function is applicable only for STM32F072 devices.
+ * @param DAC_Align: Specifies the data alignment for dual channel DAC.
+ * This parameter can be:
+ * @arg DAC_Align_8b_R: 8bit right data alignment selected
+ * @arg DAC_Align_12b_L: 12bit left data alignment selected
+ * @arg DAC_Align_12b_R: 12bit right data alignment selected
+ * @param Data2: Data for DAC Channel2 to be loaded in the selected data holding register.
+ * @param Data1: Data for DAC Channel1 to be loaded in the selected data holding register.
+ * @note In dual mode, a unique register access is required to write in both
+ * DAC channels at the same time.
+ * @retval None
+ */
+void DAC_SetDualChannelData(uint32_t DAC_Align, uint16_t Data2, uint16_t Data1)
+{
+ uint32_t data = 0, tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_DAC_ALIGN(DAC_Align));
+ assert_param(IS_DAC_DATA(Data1));
+ assert_param(IS_DAC_DATA(Data2));
+
+ /* Calculate and set dual DAC data holding register value */
+ if (DAC_Align == DAC_Align_8b_R)
+ {
+ data = ((uint32_t)Data2 << 8) | Data1;
+ }
+ else
+ {
+ data = ((uint32_t)Data2 << 16) | Data1;
+ }
+
+ tmp = (uint32_t)DAC_BASE;
+ tmp += DHR12RD_OFFSET + DAC_Align;
+
+ /* Set the dual DAC selected data holding register */
+ *(__IO uint32_t *)tmp = data;
+}
+
+/**
+ * @brief Returns the last data output value of the selected DAC channel.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @retval The selected DAC channel data output value.
+ */
+uint16_t DAC_GetDataOutputValue(uint32_t DAC_Channel)
+{
+ __IO uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+
+ tmp = (uint32_t) DAC_BASE ;
+ tmp += DOR_OFFSET + ((uint32_t)DAC_Channel >> 2);
+
+ /* Returns the DAC channel data output register value */
+ return (uint16_t) (*(__IO uint32_t*) tmp);
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup DAC_Group2 DMA management functions
+ * @brief DMA management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### DMA management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables or disables the specified DAC channel DMA request.
+ * When enabled DMA1 is generated when an external trigger (EXTI Line9,
+ * TIM2, TIM3, TIM6 or TIM15 but not a software trigger) occurs
+ * @param DAC_Channel: the selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param NewState: new state of the selected DAC channel DMA request.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The DAC channel1 is mapped on DMA1 channel3 which must be already configured.
+ * @note The DAC channel2 is mapped on DMA1 channel4 which must be already configured.
+ * @retval None
+ */
+void DAC_DMACmd(uint32_t DAC_Channel, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected DAC channel DMA request */
+ DAC->CR |= (DAC_CR_DMAEN1 << DAC_Channel);
+ }
+ else
+ {
+ /* Disable the selected DAC channel DMA request */
+ DAC->CR &= (~(DAC_CR_DMAEN1 << DAC_Channel));
+ }
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup DAC_Group3 Interrupts and flags management functions
+ * @brief Interrupts and flags management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Interrupts and flags management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables or disables the specified DAC interrupts.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_IT: specifies the DAC interrupt sources to be enabled or disabled.
+ * This parameter can be the following values:
+ * @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
+ * @note The DMA underrun occurs when a second external trigger arrives before the
+ * acknowledgement for the first external trigger is received (first request).
+ * @param NewState: new state of the specified DAC interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void DAC_ITConfig(uint32_t DAC_Channel, uint32_t DAC_IT, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ assert_param(IS_DAC_IT(DAC_IT));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected DAC interrupts */
+ DAC->CR |= (DAC_IT << DAC_Channel);
+ }
+ else
+ {
+ /* Disable the selected DAC interrupts */
+ DAC->CR &= (~(uint32_t)(DAC_IT << DAC_Channel));
+ }
+}
+
+/**
+ * @brief Checks whether the specified DAC flag is set or not.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_FLAG: specifies the flag to check.
+ * This parameter can be only of the following value:
+ * @arg DAC_FLAG_DMAUDR: DMA underrun flag
+ * @note The DMA underrun occurs when a second external trigger arrives before the
+ * acknowledgement for the first external trigger is received (first request).
+ * @retval The new state of DAC_FLAG (SET or RESET).
+ */
+FlagStatus DAC_GetFlagStatus(uint32_t DAC_Channel, uint32_t DAC_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_DAC_FLAG(DAC_FLAG));
+
+ /* Check the status of the specified DAC flag */
+ if ((DAC->SR & (DAC_FLAG << DAC_Channel)) != (uint8_t)RESET)
+ {
+ /* DAC_FLAG is set */
+ bitstatus = SET;
+ }
+ else
+ {
+ /* DAC_FLAG is reset */
+ bitstatus = RESET;
+ }
+ /* Return the DAC_FLAG status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the DAC channel's pending flags.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_FLAG: specifies the flag to clear.
+ * This parameter can be of the following value:
+ * @arg DAC_FLAG_DMAUDR: DMA underrun flag
+ * @retval None
+ */
+void DAC_ClearFlag(uint32_t DAC_Channel, uint32_t DAC_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_DAC_FLAG(DAC_FLAG));
+
+ /* Clear the selected DAC flags */
+ DAC->SR = (DAC_FLAG << DAC_Channel);
+}
+
+/**
+ * @brief Checks whether the specified DAC interrupt has occurred or not.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_IT: specifies the DAC interrupt source to check.
+ * This parameter can be the following values:
+ * @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
+ * @note The DMA underrun occurs when a second external trigger arrives before the
+ * acknowledgement for the first external trigger is received (first request).
+ * @retval The new state of DAC_IT (SET or RESET).
+ */
+ITStatus DAC_GetITStatus(uint32_t DAC_Channel, uint32_t DAC_IT)
+{
+ ITStatus bitstatus = RESET;
+ uint32_t enablestatus = 0;
+
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_DAC_IT(DAC_IT));
+
+ /* Get the DAC_IT enable bit status */
+ enablestatus = (DAC->CR & (DAC_IT << DAC_Channel)) ;
+
+ /* Check the status of the specified DAC interrupt */
+ if (((DAC->SR & (DAC_IT << DAC_Channel)) != (uint32_t)RESET) && enablestatus)
+ {
+ /* DAC_IT is set */
+ bitstatus = SET;
+ }
+ else
+ {
+ /* DAC_IT is reset */
+ bitstatus = RESET;
+ }
+ /* Return the DAC_IT status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the DAC channel's interrupt pending bits.
+ * @param DAC_Channel: The selected DAC channel.
+ * This parameter can be one of the following values:
+ * @arg DAC_Channel_1: DAC Channel1 selected
+ * @arg DAC_Channel_2: DAC Channel2 selected, applicable only for STM32F072 devices
+ * @param DAC_IT: specifies the DAC interrupt pending bit to clear.
+ * This parameter can be the following values:
+ * @arg DAC_IT_DMAUDR: DMA underrun interrupt mask
+ * @retval None
+ */
+void DAC_ClearITPendingBit(uint32_t DAC_Channel, uint32_t DAC_IT)
+{
+ /* Check the parameters */
+ assert_param(IS_DAC_CHANNEL(DAC_Channel));
+ assert_param(IS_DAC_IT(DAC_IT));
+
+ /* Clear the selected DAC interrupt pending bits */
+ DAC->SR = (DAC_IT << DAC_Channel);
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/