minicube.net .
Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of
mbed-src
by 
mbed official
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。（2013/10/28）
パスが通ってないだけのようなのでファイルを以下に移動する。
| mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
| mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
| TOOLCHAIN_ARM_MICRO |
をフォルダごと
| mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
| mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
| mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
 |
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
Last commit 27 Oct 2013 by 
minicube.net .
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
| Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_NXP/TARGET_LPC11XX_11CXX/sleep.c
- Revision:
- 43:b3acfef78949
- Parent:
- 42:7ca0bbba899b
--- a/targets/hal/TARGET_NXP/TARGET_LPC11XX_11CXX/sleep.c Sun Oct 27 16:30:04 2013 +0000
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,79 +0,0 @@
-/* mbed Microcontroller Library
- * Copyright (c) 2006-2013 ARM Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#include "sleep_api.h"
-#include "cmsis.h"
-#include "mbed_interface.h"
-
-void sleep(void) {
-#if DEVICE_SEMIHOST
- // ensure debug is disconnected
- mbed_interface_disconnect();
-#endif
-
- // PCON[DPDEN] set to sleep
- LPC_PMU->PCON = 0x0;
-
- // SRC[SLEEPDEEP] set to 0 = sleep
- SCB->SCR &= ~SCB_SCR_SLEEPDEEP_Msk;
-
- // wait for interrupt
- __WFI();
-}
-
-/*
-* The mbed lpc1768 does not support the deepsleep mode
-* as a debugger is connected to it (the mbed interface).
-*
-* As mentionned in an application note from NXP:
-*
-* http://www.po-star.com/public/uploads/20120319123122_141.pdf
-*
-* {{{
-* The user should be aware of certain limitations during debugging.
-* The most important is that, due to limitations of the Cortex-M3
-* integration, the LPC17xx cannot wake up in the usual manner from
-* Deep Sleep and Power-down modes. It is recommended not to use these
-* modes during debug. Once an application is downloaded via JTAG/SWD
-* interface, the USB to SWD/JTAG debug adapter (Keil ULINK2 for example)
-* should be removed from the target board, and thereafter, power cycle
-* the LPC17xx to allow wake-up from deep sleep and power-down modes
-* }}}
-*
-* As the interface firmware does not reset the target when a
-* mbed_interface_disconnect() semihosting call is made, the
-* core cannot wake-up from deepsleep.
-*
-* We treat a deepsleep() as a normal sleep().
-*/
-
-void deepsleep(void) {
-#if DEVICE_SEMIHOST
- // ensure debug is disconnected
- mbed_interface_disconnect();
-#endif
-
- // PCON[DPDEN] set to deepsleep
- LPC_PMU->PCON = 0x2;
-
- // SRC[SLEEPDEEP] set to 1 = deep sleep
- SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
-
- // Power up everything after powerdown
- LPC_SYSCON->PDAWAKECFG &= 0xFFFFF800;
-
- // wait for interrupt
- __WFI();
-}