Diff: targets/cmsis/TARGET_NXP/TARGET_LPC11UXX/power_api.h

Revision:

43:b3acfef78949

Parent:

42:7ca0bbba899b

--- a/targets/cmsis/TARGET_NXP/TARGET_LPC11UXX/power_api.h	Sun Oct 27 16:30:04 2013 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,82 +0,0 @@
-/****************************************************************************
- *   $Id:: power_api.h 6249 2011-01-25 19:23:47Z usb01267                   $
- *   Project: NXP LPC11Uxx software example  
- *
- *   Description:
- *     Power API Header File for NXP LPC11Uxx Device Series 
- *
- ****************************************************************************
- * Software that is described herein is for illustrative purposes only
- * which provides customers with programming information regarding the
- * products. This software is supplied "AS IS" without any warranties.
- * NXP Semiconductors assumes no responsibility or liability for the
- * use of the software, conveys no license or title under any patent,
- * copyright, or mask work right to the product. NXP Semiconductors
- * reserves the right to make changes in the software without
- * notification. NXP Semiconductors also make no representation or
- * warranty that such application will be suitable for the specified
- * use without further testing or modification.
-****************************************************************************/
-#ifndef __LPC11UXX_POWER_API_H__
-#define __LPC11UXX_POWER_API_H__
-
-#ifdef __cplusplus
- extern "C" {
-#endif 
-
-#define PWRROMD_PRESENT
-
-typedef	struct _PWRD {
-  void (*set_pll)(unsigned int cmd[], unsigned int resp[]);
-  void (*set_power)(unsigned int cmd[], unsigned int resp[]);
-}  PWRD;
-
-typedef	struct _ROM {
-#ifdef USBROMD_PRESENT
-   const USB * pUSBD;
-#else
-   const unsigned p_usbd;
-#endif /* USBROMD_PRESENT */
-   const unsigned p_clib;
-   const unsigned p_cand;
-#ifdef PWRROMD_PRESENT
-   const PWRD * pPWRD;
-#else
-   const unsigned p_pwrd;
-#endif /* PWRROMD_PRESENT */
-   const unsigned p_dev1;
-   const unsigned p_dev2;
-   const unsigned p_dev3;
-   const unsigned p_dev4; 
-}  ROM;
-
-//PLL setup related definitions
-#define	CPU_FREQ_EQU  		0       //main PLL freq must be equal to the specified 
-#define	CPU_FREQ_LTE		1       //main PLL freq must be less than or equal the specified
-#define	CPU_FREQ_GTE		2       //main PLL freq must be greater than or equal the specified
-#define	CPU_FREQ_APPROX		3       //main PLL freq must be as close as possible the specified
-
-#define	PLL_CMD_SUCCESS		0       //PLL setup successfully found
-#define	PLL_INVALID_FREQ	1       //specified freq out of range (either input or output)
-#define	PLL_INVALID_MODE	2       //invalid mode (see above for valid) specified
-#define	PLL_FREQ_NOT_FOUND	3       //specified freq not found under specified conditions
-#define	PLL_NOT_LOCKED		4       //PLL not locked => no changes to the PLL setup
-
-//power setup elated definitions
-#define	PARAM_DEFAULT			0   //default power settings (voltage regulator, flash interface)
-#define	PARAM_CPU_PERFORMANCE	1   //setup for maximum CPU performance (higher current, more computation)
-#define	PARAM_EFFICIENCY		2   //balanced setting (power vs CPU performance)
-#define	PARAM_LOW_CURRENT		3   //lowest active current, lowest CPU performance
-
-#define	PARAM_CMD_SUCCESS		0   //power setting successfully found
-#define	PARAM_INVALID_FREQ		1   //specified freq out of range (=0 or > 50 MHz)
-#define	PARAM_INVALID_MODE		2   //specified mode not valid (see above for valid)
-
-#define MAX_CLOCK_KHZ_PARAM                50000
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif  /* __LPC11UXX_POWER_API_H__ */
-