Diff: targets/hal/TARGET_Atmel/TARGET_SAM21/drivers/sercom/i2c/quick_start_slave/qs_i2c_slave_basic_use.h

Revision:

613:bc40b8d2aec4

Parent:

612:fba1c7dc54c0

Child:

614:9d86c2ae5de0

--- a/targets/hal/TARGET_Atmel/TARGET_SAM21/drivers/sercom/i2c/quick_start_slave/qs_i2c_slave_basic_use.h	Tue Aug 18 15:00:09 2015 +0100
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,66 +0,0 @@
-/**
- * \page asfdoc_sam0_sercom_i2c_slave_basic_use_case Quick Start Guide for SERCOM I2C Slave - Basic
- *
- * In this use case, the I<SUP>2</SUP>C will used and set up as follows:
- *  - Slave mode
- *  - 100KHz operation speed
- *  - Not operational in standby
- *  - 10000 packet timeout value
- *
- * \section asfdoc_sam0_sercom_i2c_slave_basic_use_case_prereq Prerequisites
- * The device must be connected to an I<SUP>2</SUP>C master.
- *
- * \section asfdoc_sam0_sercom_i2c_slave_basic_use_case_setup_code Setup
- *
- * \subsection asfdoc_sam0_sercom_i2c_slave_basic_use_setup_code Code
- * The following must be added to the user application:
- *
- * A sample buffer to write from, a sample buffer to read to and length of buffers:
- * \snippet qs_i2c_slave_basic_use.c packet_data
- *
- * Address to respond to:
- * \snippet qs_i2c_slave_basic_use.c address
- *
- * Globally accessible module structure:
- * \snippet qs_i2c_slave_basic_use.c module
- *
- * Function for setting up the module:
- * \snippet qs_i2c_slave_basic_use.c initialize_i2c
- *
- * Add to user application \c main():
- * \snippet qs_i2c_slave_basic_use.c run_initialize_i2c
- *
- * \subsection asfdoc_sam0_sercom_i2c_slave_basic_use_setup_workflow Workflow
- * -# Configure and enable module.
- *    \snippet qs_i2c_slave_basic_use.c config
- *   -# Create and initialize configuration structure.
- *      \snippet qs_i2c_slave_basic_use.c init_conf
- *   -# Change address and address mode settings in the configuration.
- *      \snippet qs_i2c_slave_basic_use.c conf_changes
- *   -# Initialize the module with the set configurations.
- *      \snippet qs_i2c_slave_basic_use.c init_module
- *   -# Enable the module.
- *      \snippet qs_i2c_slave_basic_use.c enable_module
- * -# Create variable to hold transfer direction.
- *    \snippet qs_i2c_slave_basic_use.c dir
- * -# Create packet variable to transfer.
- *    \snippet qs_i2c_slave_basic_use.c pack
- *
- * \section asfdoc_sam0_sercom_i2c_slave_basic_use_implementation Implementation
- * \subsection asfdoc_sam0_sercom_i2c_slave_basic_use_implementation_code Code
- * Add to user application \c main():
- * \snippet qs_i2c_slave_basic_use.c while
- * \subsection i2c_slave_basic_use_implementation_workflow Workflow
- * -# Wait for start condition from master and get transfer direction.
- *    \snippet qs_i2c_slave_basic_use.c get_dir
- * -# Depending on transfer direction, set up buffer to read to or write from,
- *    and write or read from master.
- *    \snippet qs_i2c_slave_basic_use.c transfer
- */
-/**
-* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
-*/
-
-#include <asf.h>
-#include <conf_clocks.h>
-