Diff: USBDevice/USBDevice/USBBusInterface_LPC17_LPC23.cpp

Revision:

7:6494da2a5c60

Parent:

6:126c4d980196

Child:

8:534fd41d8cc7

--- a/USBDevice/USBDevice/USBBusInterface_LPC17_LPC23.cpp	Mon Nov 14 10:00:07 2011 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,682 +0,0 @@
-// USBBusInterface_LPC17_LPC23.c
-// USB Bus Interface for NXP LPC1768 and LPC2368
-// Copyright (c) 2011 ARM Limited. All rights reserved.
-
-#ifdef TARGET_LPC1768
-
-#include "USBBusInterface.h"
-
-
-// Get endpoint direction
-#define IN_EP(endpoint)     ((endpoint) & 1U ? true : false)
-#define OUT_EP(endpoint)    ((endpoint) & 1U ? false : true)
-
-// Convert physical endpoint number to register bit
-#define EP(endpoint) (1UL<<endpoint)
-
-// Power Control for Peripherals register
-#define PCUSB      (1UL<<31)
-
-// USB Clock Control register
-#define DEV_CLK_EN (1UL<<1)
-#define AHB_CLK_EN (1UL<<4)
-
-// USB Clock Status register
-#define DEV_CLK_ON (1UL<<1)
-#define AHB_CLK_ON (1UL<<4)
-
-// USB Device Interupt registers
-#define FRAME      (1UL<<0)
-#define EP_FAST    (1UL<<1)
-#define EP_SLOW    (1UL<<2)
-#define DEV_STAT   (1UL<<3)
-#define CCEMPTY    (1UL<<4)
-#define CDFULL     (1UL<<5)
-#define RxENDPKT   (1UL<<6)
-#define TxENDPKT   (1UL<<7)
-#define EP_RLZED   (1UL<<8)
-#define ERR_INT    (1UL<<9)
-
-// USB Control register
-#define RD_EN (1<<0)
-#define WR_EN (1<<1)
-#define LOG_ENDPOINT(endpoint) ((endpoint>>1)<<2)
-
-// USB Receive Packet Length register
-#define DV      (1UL<<10)
-#define PKT_RDY (1UL<<11)
-#define PKT_LNGTH_MASK (0x3ff)
-
-// Serial Interface Engine (SIE)
-#define SIE_WRITE   (0x01)
-#define SIE_READ    (0x02)
-#define SIE_COMMAND (0x05)
-#define SIE_CMD_CODE(phase, data) ((phase<<8)|(data<<16))
-
-// SIE Command codes
-#define SIE_CMD_SET_ADDRESS        (0xD0)
-#define SIE_CMD_CONFIGURE_DEVICE   (0xD8)
-#define SIE_CMD_SET_MODE           (0xF3)
-#define SIE_CMD_READ_FRAME_NUMBER  (0xF5)
-#define SIE_CMD_READ_TEST_REGISTER (0xFD)
-#define SIE_CMD_SET_DEVICE_STATUS  (0xFE)
-#define SIE_CMD_GET_DEVICE_STATUS  (0xFE)
-#define SIE_CMD_GET_ERROR_CODE     (0xFF)
-#define SIE_CMD_READ_ERROR_STATUS  (0xFB)
-
-#define SIE_CMD_SELECT_ENDPOINT(endpoint)                 (0x00+endpoint)
-#define SIE_CMD_SELECT_ENDPOINT_CLEAR_INTERRUPT(endpoint) (0x40+endpoint)
-#define SIE_CMD_SET_ENDPOINT_STATUS(endpoint)             (0x40+endpoint)
-
-#define SIE_CMD_CLEAR_BUFFER    (0xF2)
-#define SIE_CMD_VALIDATE_BUFFER (0xFA)
-
-// SIE Device Status register
-#define SIE_DS_CON    (1<<0)
-#define SIE_DS_CON_CH (1<<1)
-#define SIE_DS_SUS    (1<<2)
-#define SIE_DS_SUS_CH (1<<3)
-#define SIE_DS_RST    (1<<4)
-
-// SIE Device Set Address register
-#define SIE_DSA_DEV_EN  (1<<7)
-
-// SIE Configue Device register
-#define SIE_CONF_DEVICE (1<<0)
-
-// Select Endpoint register
-#define SIE_SE_FE       (1<<0)
-#define SIE_SE_ST       (1<<1)
-#define SIE_SE_STP      (1<<2)
-#define SIE_SE_PO       (1<<3)
-#define SIE_SE_EPN      (1<<4)
-#define SIE_SE_B_1_FULL (1<<5)
-#define SIE_SE_B_2_FULL (1<<6)
-
-// Set Endpoint Status command
-#define SIE_SES_ST      (1<<0)
-#define SIE_SES_DA      (1<<5)
-#define SIE_SES_RF_MO   (1<<6)
-#define SIE_SES_CND_ST  (1<<7)
-
-
-USBHAL * USBHAL::instance;
-
-volatile int epComplete;
-uint32_t endpointStallState;
-
-static void SIECommand(uint32_t command)
-{
-    // The command phase of a SIE transaction
-    LPC_USB->USBDevIntClr = CCEMPTY;
-    LPC_USB->USBCmdCode = SIE_CMD_CODE(SIE_COMMAND, command);
-    while (!(LPC_USB->USBDevIntSt & CCEMPTY));
-}
-
-static void SIEWriteData(uint8_t data)
-{
-    // The data write phase of a SIE transaction
-    LPC_USB->USBDevIntClr = CCEMPTY;
-    LPC_USB->USBCmdCode = SIE_CMD_CODE(SIE_WRITE, data);
-    while (!(LPC_USB->USBDevIntSt & CCEMPTY));
-}
-
-static uint8_t SIEReadData(uint32_t command)
-{
-    // The data read phase of a SIE transaction
-    LPC_USB->USBDevIntClr = CDFULL;
-    LPC_USB->USBCmdCode = SIE_CMD_CODE(SIE_READ, command);
-    while (!(LPC_USB->USBDevIntSt & CDFULL));
-    return (uint8_t)LPC_USB->USBCmdData;
-}
-
-static void SIEsetDeviceStatus(uint8_t status)
-{
-    // Write SIE device status register
-    SIECommand(SIE_CMD_SET_DEVICE_STATUS);
-    SIEWriteData(status);
-}
-
-static uint8_t SIEgetDeviceStatus(void)
-{
-    // Read SIE device status register
-    SIECommand(SIE_CMD_GET_DEVICE_STATUS);
-    return SIEReadData(SIE_CMD_GET_DEVICE_STATUS);
-}
-
-void SIEsetAddress(uint8_t address)
-{
-    // Write SIE device address register
-    SIECommand(SIE_CMD_SET_ADDRESS);
-    SIEWriteData((address & 0x7f) | SIE_DSA_DEV_EN);
-}
-
-static uint8_t SIEselectEndpoint(uint8_t endpoint)
-{
-    // SIE select endpoint command
-    SIECommand(SIE_CMD_SELECT_ENDPOINT(endpoint));
-    return SIEReadData(SIE_CMD_SELECT_ENDPOINT(endpoint));
-}
-
-static uint8_t SIEclearBuffer(void)
-{
-    // SIE clear buffer command
-    SIECommand(SIE_CMD_CLEAR_BUFFER);
-    return SIEReadData(SIE_CMD_CLEAR_BUFFER);
-}
-
-static void SIEvalidateBuffer(void)
-{
-    // SIE validate buffer command
-    SIECommand(SIE_CMD_VALIDATE_BUFFER);
-}
-
-static void SIEsetEndpointStatus(uint8_t endpoint, uint8_t status)
-{
-    // SIE set endpoint status command
-    SIECommand(SIE_CMD_SET_ENDPOINT_STATUS(endpoint));
-    SIEWriteData(status);
-}
-
-static uint16_t SIEgetFrameNumber(void) __attribute__ ((unused));
-static uint16_t SIEgetFrameNumber(void)
-{
-    // Read current frame number
-    uint16_t lowByte;
-    uint16_t highByte;
-
-    SIECommand(SIE_CMD_READ_FRAME_NUMBER);
-    lowByte = SIEReadData(SIE_CMD_READ_FRAME_NUMBER);
-    highByte = SIEReadData(SIE_CMD_READ_FRAME_NUMBER);
-
-    return (highByte << 8) | lowByte;
-}
-
-static void SIEconfigureDevice(void)
-{
-    // SIE Configure device command
-    SIECommand(SIE_CMD_CONFIGURE_DEVICE);
-    SIEWriteData(SIE_CONF_DEVICE);
-}
-
-static void SIEunconfigureDevice(void)
-{
-    // SIE Configure device command
-    SIECommand(SIE_CMD_CONFIGURE_DEVICE);
-    SIEWriteData(0);
-}
-
-static void SIEconnect(void)
-{
-    // Connect USB device
-    uint8_t status;
-
-    status = SIEgetDeviceStatus();
-    SIEsetDeviceStatus(status | SIE_DS_CON);
-}
-
-
-static void SIEdisconnect(void)
-{
-    // Disconnect USB device
-    uint8_t status;
-
-    status = SIEgetDeviceStatus();
-    SIEsetDeviceStatus(status & ~SIE_DS_CON);
-}
-
-
-static uint8_t selectEndpointClearInterrupt(uint8_t endpoint)
-{
-    // Implemented using using EP_INT_CLR.
-    LPC_USB->USBEpIntClr = EP(endpoint);
-    while (!(LPC_USB->USBDevIntSt & CDFULL));
-    return (uint8_t)LPC_USB->USBCmdData;
-}
-
-
-
-
-
-static void enableEndpointEvent(uint8_t endpoint)
-{
-    // Enable an endpoint interrupt
-    LPC_USB->USBEpIntEn |= EP(endpoint);
-}
-
-static void disableEndpointEvent(uint8_t endpoint) __attribute__ ((unused));
-static void disableEndpointEvent(uint8_t endpoint)
-{
-    // Disable an endpoint interrupt
-    LPC_USB->USBEpIntEn &= ~EP(endpoint);
-}
-
-static volatile uint32_t __attribute__((used)) dummyRead;
-
-
-static uint32_t endpointReadcore(uint8_t endpoint, uint8_t *buffer)
-{
-    // Read from an OUT endpoint
-    uint32_t size;
-    uint32_t i;
-    uint32_t data = 0;
-    uint8_t offset;
-
-    LPC_USB->USBCtrl = LOG_ENDPOINT(endpoint) | RD_EN;
-    while (!(LPC_USB->USBRxPLen & PKT_RDY));
-
-    size = LPC_USB->USBRxPLen & PKT_LNGTH_MASK;
-
-    offset = 0;
-
-    if (size > 0)
-    {
-        for (i=0; i<size; i++)
-        {
-            if (offset==0)
-            {
-                // Fetch up to four bytes of data as a word
-                data = LPC_USB->USBRxData;
-            }
-
-            // extract a byte
-            *buffer = (data>>offset) & 0xff;
-            buffer++;
-
-            // move on to the next byte
-            offset = (offset + 8) % 32;
-        }
-    }
-    else
-    {
-        dummyRead = LPC_USB->USBRxData;
-    }
-
-    SIEselectEndpoint(endpoint);
-    SIEclearBuffer();
-    return size;
-}
-
-static void endpointWritecore(uint8_t endpoint, uint8_t *buffer, uint32_t size)
-{
-    // Write to an IN endpoint
-    uint32_t temp, data;
-    uint8_t offset;
-
-    LPC_USB->USBCtrl = LOG_ENDPOINT(endpoint) | WR_EN;
-
-    LPC_USB->USBTxPLen = size;
-    offset = 0;
-    data = 0;
-
-    if (size>0)
-    {
-        do {
-            // Fetch next data byte into a word-sized temporary variable
-            temp = *buffer++;
-
-            // Add to current data word
-            temp = temp << offset;
-            data = data | temp;
-
-            // move on to the next byte
-            offset = (offset + 8) % 32;
-            size--;
-
-            if ((offset==0) || (size==0))
-            {
-                // Write the word to the endpoint
-                LPC_USB->USBTxData = data;
-                data = 0;
-            }
-        } while (size>0);
-    }
-    else
-    {
-        LPC_USB->USBTxData = 0;
-    }
-
-    // Clear WR_EN to cover zero length packet case
-    LPC_USB->USBCtrl=0;
-
-    SIEselectEndpoint(endpoint);
-    SIEvalidateBuffer();
-}
-
-
-
-
-
-
-
-USBHAL::USBHAL(void)
-{
-    // Disable IRQ
-    NVIC_DisableIRQ(USB_IRQn);
-
-    // Enable power to USB device controller
-    LPC_SC->PCONP |= PCUSB;
-
-    // Enable USB clocks
-    LPC_USB->USBClkCtrl |= DEV_CLK_EN | AHB_CLK_EN;
-    while (LPC_USB->USBClkSt != (DEV_CLK_ON | AHB_CLK_ON));
-
-    // Configure pins P0.29 and P0.30 to be USB D+ and USB D-
-    LPC_PINCON->PINSEL1 &= 0xc3ffffff;
-    LPC_PINCON->PINSEL1 |= 0x14000000;
-
-    // Disconnect USB device
-    SIEdisconnect();
-
-    // Configure pin P2.9 to be Connect
-    LPC_PINCON->PINSEL4 &= 0xfffcffff;
-    LPC_PINCON->PINSEL4 |= 0x00040000;
-
-    // Connect must be low for at least 2.5uS
-    wait(0.3);
-
-    // Set the maximum packet size for the control endpoints
-    realiseEndpoint(EP0IN, MAX_PACKET_SIZE_EP0, 0);
-    realiseEndpoint(EP0OUT, MAX_PACKET_SIZE_EP0, 0);
-
-    // Attach IRQ
-    instance = this;
-    NVIC_SetVector(USB_IRQn, (uint32_t)&_usbisr);
-    NVIC_EnableIRQ(USB_IRQn);
-
-    // Enable interrupts for device events and EP0
-    LPC_USB->USBDevIntEn = EP_SLOW | DEV_STAT;
-    enableEndpointEvent(EP0IN);
-    enableEndpointEvent(EP0OUT);
-}
-
-USBHAL::~USBHAL(void)
-{
-    // Ensure device disconnected
-    SIEdisconnect();
-
-    // Disable USB interrupts
-    NVIC_DisableIRQ(USB_IRQn);
-}
-
-void USBHAL::connect(void)
-{
-    // Connect USB device
-    SIEconnect();
-}
-
-void USBHAL::disconnect(void)
-{
-    // Disconnect USB device
-    SIEdisconnect();
-}
-
-void USBHAL::configureDevice(void)
-{
-    SIEconfigureDevice();
-}
-
-void USBHAL::unconfigureDevice(void)
-{
-    SIEunconfigureDevice();
-}
-
-void USBHAL::setAddress(uint8_t address)
-{
-    SIEsetAddress(address);
-}
-
-void USBHAL::EP0setup(uint8_t *buffer)
-{
-    endpointReadcore(EP0OUT, buffer);
-}
-
-void USBHAL::EP0read(void)
-{
-    // Not required
-}
-
-uint32_t USBHAL::EP0getReadResult(uint8_t *buffer)
-{
-    return endpointReadcore(EP0OUT, buffer);
-}
-
-void USBHAL::EP0write(uint8_t *buffer, uint32_t size)
-{
-    endpointWritecore(EP0IN, buffer, size);
-}
-
-void USBHAL::EP0getWriteResult(void)
-{
-    // Not required
-}
-
-void USBHAL::EP0stall(void)
-{
-    // This will stall both control endpoints
-    stallEndpoint(EP0OUT);
-}
-
-EP_STATUS USBHAL::endpointRead(uint8_t endpoint, uint32_t maximumSize)
-{
-    return EP_PENDING;
-}
-
-EP_STATUS USBHAL::endpointReadResult(uint8_t endpoint, uint8_t * buffer, uint32_t *bytesRead)
-{
-    if(!(epComplete & EP(endpoint)))
-        return EP_PENDING;
-    *bytesRead = endpointReadcore(endpoint, buffer);
-    epComplete &= ~EP(endpoint);
-    return EP_COMPLETED;
-}
-
-EP_STATUS USBHAL::endpointWrite(uint8_t endpoint, uint8_t *data, uint32_t size)
-{
-    if (getEndpointStallState(endpoint))
-    {
-        return EP_STALLED;
-    }
-
-    epComplete &= ~EP(endpoint);
-
-    endpointWritecore(endpoint, data, size);
-    return EP_PENDING;
-}
-
-EP_STATUS USBHAL::endpointWriteResult(uint8_t endpoint)
-{
-    if (epComplete & EP(endpoint))
-    {
-        epComplete &= ~EP(endpoint);
-        return EP_COMPLETED;
-    }
-
-    return EP_PENDING;
-}
-
-bool USBHAL::realiseEndpoint(uint8_t endpoint, uint32_t maxPacket, uint32_t flags)
-{
-    // Realise an endpoint
-    LPC_USB->USBDevIntClr = EP_RLZED;
-    LPC_USB->USBReEp |= EP(endpoint);
-    LPC_USB->USBEpInd = endpoint;
-    LPC_USB->USBMaxPSize = maxPacket;
-
-    while (!(LPC_USB->USBDevIntSt & EP_RLZED));
-    LPC_USB->USBDevIntClr = EP_RLZED;
-
-    // Clear stall state
-    endpointStallState &= ~EP(endpoint);
-
-    enableEndpointEvent(endpoint);
-    return true;
-}
-
-void USBHAL::stallEndpoint(uint8_t endpoint)
-{
-    // Stall an endpoint
-    if ( (endpoint==EP0IN) || (endpoint==EP0OUT) )
-    {
-        // Conditionally stall both control endpoints
-        SIEsetEndpointStatus(EP0OUT, SIE_SES_CND_ST);
-    }
-    else
-    {
-        SIEsetEndpointStatus(endpoint, SIE_SES_ST);
-
-        // Update stall state
-        endpointStallState |= EP(endpoint);
-    }
-}
-
-void USBHAL::unstallEndpoint(uint8_t endpoint)
-{
-    // Unstall an endpoint. The endpoint will also be reinitialised
-    SIEsetEndpointStatus(endpoint, 0);
-
-    // Update stall state
-    endpointStallState &= ~EP(endpoint);
-}
-
-bool USBHAL::getEndpointStallState(uint8_t endpoint)
-{
-    // Returns true if endpoint stalled
-    return endpointStallState & EP(endpoint);
-}
-
-void USBHAL::remoteWakeup(void)
-{
-    // Remote wakeup
-    uint8_t status;
-
-    // Enable USB clocks
-    LPC_USB->USBClkCtrl |= DEV_CLK_EN | AHB_CLK_EN;
-    while (LPC_USB->USBClkSt != (DEV_CLK_ON | AHB_CLK_ON));
-
-    status = SIEgetDeviceStatus();
-    SIEsetDeviceStatus(status & ~SIE_DS_SUS);
-}
-
-
-
-
-
-void USBHAL::_usbisr(void)
-{
-    instance->usbisr();
-} 
-
-
-void USBHAL::usbisr(void)
-{ 
-    uint8_t devStat;
-
-    if (LPC_USB->USBDevIntSt & FRAME)
-    {
-        // Start of frame event
-        SOF(SIEgetFrameNumber());
-        // Clear interrupt status flag
-        LPC_USB->USBDevIntClr = FRAME;
-    }
-
-    if (LPC_USB->USBDevIntSt & DEV_STAT)
-    {
-        // Device Status interrupt
-        // Must clear the interrupt status flag before reading the device status from the SIE
-        LPC_USB->USBDevIntClr = DEV_STAT;
-
-        // Read device status from SIE
-        devStat = SIEgetDeviceStatus();
-
-        if (devStat & SIE_DS_RST)
-        {
-            // Bus reset
-            busReset();
-        }
-    }
-
-    if (LPC_USB->USBDevIntSt & EP_SLOW)
-    {
-        // (Slow) Endpoint Interrupt
-
-        // Process each endpoint interrupt
-        if (LPC_USB->USBEpIntSt & EP(EP0OUT))
-        {
-            if (selectEndpointClearInterrupt(EP0OUT) & SIE_SE_STP)
-            {
-                // this is a setup packet
-                EP0setupCallback();
-            }
-            else
-            {
-                EP0out();
-            }
-            LPC_USB->USBDevIntClr = EP_SLOW;
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP0IN))
-        {
-            selectEndpointClearInterrupt(EP0IN);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            EP0in();
-        }
-
-        // TODO: This should cover all endpoints, not just EP1,2,3:
-        if (LPC_USB->USBEpIntSt & EP(EP1IN))
-        {
-            selectEndpointClearInterrupt(EP1IN);
-            epComplete |= EP(EP1IN);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP1_IN_callback())
-                epComplete &= ~EP(EP1IN);
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP1OUT))
-        {
-            selectEndpointClearInterrupt(EP1OUT);
-            epComplete |= EP(EP1OUT);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP1_OUT_callback())
-                epComplete &= ~EP(EP1OUT);
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP2IN))
-        {
-            selectEndpointClearInterrupt(EP2IN);
-            epComplete |= EP(EP2IN);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP2_IN_callback())
-                epComplete &= ~EP(EP2IN);
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP2OUT))
-        {
-            selectEndpointClearInterrupt(EP2OUT);
-            epComplete |= EP(EP2OUT);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP2_OUT_callback())
-                epComplete &= ~EP(EP2OUT);
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP3IN))
-        {
-            selectEndpointClearInterrupt(EP3IN);
-            epComplete |= EP(EP3IN);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP3_IN_callback())
-                epComplete &= ~EP(EP3IN);
-        }
-
-        if (LPC_USB->USBEpIntSt & EP(EP3OUT))
-        {
-            selectEndpointClearInterrupt(EP3OUT);
-            epComplete |= EP(EP3OUT);
-            LPC_USB->USBDevIntClr = EP_SLOW;
-            if(EP3_OUT_callback())
-                epComplete &= ~EP(EP3OUT);
-        }
-    }
-}
-
-#endif