Diff: targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_uart_ex.c

Revision:

610:813dcc80987e

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_uart_ex.c	Fri Aug 14 13:15:17 2015 +0100
@@ -0,0 +1,457 @@
+/**
+  ******************************************************************************
+  * @file    stm32l4xx_hal_uart_ex.c
+  * @author  MCD Application Team
+  * @version V1.0.0
+  * @date    26-June-2015
+  * @brief   Extended UART HAL module driver.
+  *          This file provides firmware functions to manage the following extended
+  *          functionalities of the Universal Asynchronous Receiver Transmitter Peripheral (UART).
+  *           + Initialization and de-initialization functions
+  *           + Peripheral Control functions
+  *
+  *
+  @verbatim
+  ==============================================================================
+               ##### UART peripheral extended features  #####
+  ==============================================================================
+
+    (#) Declare a UART_HandleTypeDef handle structure.
+
+    (#) For the UART RS485 Driver Enable mode, initialize the UART registers
+        by calling the HAL_RS485Ex_Init() API.
+
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l4xx_hal.h"
+
+/** @addtogroup STM32L4xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup UARTEx UARTEx
+  * @brief UART Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_UART_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup UARTEx_Private_Functions UARTEx Private Functions
+  * @{
+  */
+static void UARTEx_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection);
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @defgroup UARTEx_Exported_Functions  UARTEx Exported Functions
+  * @{
+  */
+
+/** @defgroup UARTEx_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @brief    Extended Initialization and Configuration Functions
+  *
+@verbatim
+===============================================================================
+            ##### Initialization and Configuration functions #####
+ ===============================================================================
+    [..]
+    This subsection provides a set of functions allowing to initialize the USARTx or the UARTy
+    in asynchronous mode.
+      (+) For the asynchronous mode the parameters below can be configured:
+        (++) Baud Rate
+        (++) Word Length
+        (++) Stop Bit
+        (++) Parity: If the parity is enabled, then the MSB bit of the data written
+             in the data register is transmitted but is changed by the parity bit.
+             Depending on the frame length defined by the  M1 and M0 bits (7-bit,
+             8-bit or 9-bit),
+             the possible UART frame formats are as listed in the following table:
+            
+            (+++)    Table 1. UART frame format.              
+            (+++)   +-----------------------------------------------------------------------+
+            (+++)   |  M1 bit |  M0 bit |  PCE bit  |             UART frame                |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    0    |    0    |    0      |    | SB |    8 bit data   | STB |     |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    0    |    0    |    1      |    | SB | 7 bit data | PB | STB |     |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    0    |    1    |    0      |    | SB |    9 bit data   | STB |     |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    0    |    1    |    1      |    | SB | 8 bit data | PB | STB |     |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    1    |    0    |    0      |    | SB |    7 bit data   | STB |     |
+            (+++)   |---------|---------|-----------|---------------------------------------|
+            (+++)   |    1    |    0    |    1      |    | SB | 6 bit data | PB | STB |     |
+            (+++)   +-----------------------------------------------------------------------+
+        (++) Hardware flow control
+        (++) Receiver/transmitter modes
+        (++) Over Sampling Method
+        (++) One-Bit Sampling Method
+      (+) For the asynchronous mode, the following advanced features can be configured as well:
+        (++) TX and/or RX pin level inversion
+        (++) data logical level inversion
+        (++) RX and TX pins swap
+        (++) RX overrun detection disabling
+        (++) DMA disabling on RX error
+        (++) MSB first on communication line
+        (++) auto Baud rate detection
+    [..]
+    The HAL_RS485Ex_Init() API follows the UART RS485 mode configuration
+     procedures (details for the procedures are available in reference manual).
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief Initialize the RS485 Driver enable feature according to the specified
+  *         parameters in the UART_InitTypeDef and creates the associated handle.
+  * @param huart: UART handle.
+  * @param Polarity: select the driver enable polarity.
+  *        This parameter can be one of the following values:
+  *          @arg UART_DE_POLARITY_HIGH: DE signal is active high
+  *          @arg UART_DE_POLARITY_LOW: DE signal is active low
+  * @param AssertionTime: Driver Enable assertion time:
+  *                         5-bit value defining the time between the activation of the DE (Driver Enable)
+  *                         signal and the beginning of the start bit. It is expressed in sample time
+  *                         units (1/8 or 1/16 bit time, depending on the oversampling rate)
+  * @param DeassertionTime: Driver Enable deassertion time:
+  *                         5-bit value defining the time between the end of the last stop bit, in a
+  *                         transmitted message, and the de-activation of the DE (Driver Enable) signal.
+  *                         It is expressed in sample time units (1/8 or 1/16 bit time, depending on the
+  *                         oversampling rate).
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_RS485Ex_Init(UART_HandleTypeDef *huart, uint32_t Polarity, uint32_t AssertionTime, uint32_t DeassertionTime)
+{
+  uint32_t temp = 0x0;
+
+  /* Check the UART handle allocation */
+  if(huart == NULL)
+  {
+    return HAL_ERROR;
+  }
+  /* Check the Driver Enable UART instance */
+  assert_param(IS_UART_DRIVER_ENABLE_INSTANCE(huart->Instance));
+
+  /* Check the Driver Enable polarity */
+  assert_param(IS_UART_DE_POLARITY(Polarity));
+
+  /* Check the Driver Enable assertion time */
+  assert_param(IS_UART_ASSERTIONTIME(AssertionTime));
+
+  /* Check the Driver Enable deassertion time */
+  assert_param(IS_UART_DEASSERTIONTIME(DeassertionTime));
+
+  if(huart->State == HAL_UART_STATE_RESET)
+  {
+    /* Allocate lock resource and initialize it */
+    huart->Lock = HAL_UNLOCKED;
+
+    /* Init the low level hardware : GPIO, CLOCK, CORTEX */
+    HAL_UART_MspInit(huart);
+  }
+
+  huart->State = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the UART Communication parameters */
+  if (UART_SetConfig(huart) == HAL_ERROR)
+  {
+    return HAL_ERROR;
+  }
+
+  if(huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT)
+  {
+    UART_AdvFeatureConfig(huart);
+  }
+
+  /* Enable the Driver Enable mode by setting the DEM bit in the CR3 register */
+  SET_BIT(huart->Instance->CR3, USART_CR3_DEM);
+
+  /* Set the Driver Enable polarity */
+  MODIFY_REG(huart->Instance->CR3, USART_CR3_DEP, Polarity);
+
+  /* Set the Driver Enable assertion and deassertion times */
+  temp = (AssertionTime << UART_CR1_DEAT_ADDRESS_LSB_POS);
+  temp |= (DeassertionTime << UART_CR1_DEDT_ADDRESS_LSB_POS);
+  MODIFY_REG(huart->Instance->CR1, (USART_CR1_DEDT|USART_CR1_DEAT), temp);
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* TEACK and/or REACK to check before moving huart->State to Ready */
+  return (UART_CheckIdleState(huart));
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup UARTEx_Exported_Functions_Group3 Peripheral Control functions
+  * @brief    Extended Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+                      ##### Peripheral Control functions #####
+ ===============================================================================
+    [..] This section provides the following functions:
+     (+) HAL_UARTEx_EnableClockStopMode() API enables the UART clock (HSI or LSE only) during stop mode
+     (+) HAL_UARTEx_DisableClockStopMode() API disables the above functionality
+     (+) HAL_MultiProcessorEx_AddressLength_Set() API optionally sets the UART node address
+         detection length to more than 4 bits for multiprocessor address mark wake up.
+     (+) HAL_UARTEx_StopModeWakeUpSourceConfig() API defines the wake-up from stop mode
+         trigger: address match, Start Bit detection or RXNE bit status.
+     (+) HAL_UARTEx_EnableStopMode() API enables the UART to wake up the MCU from stop mode
+     (+) HAL_UARTEx_DisableStopMode() API disables the above functionality
+     (+) HAL_UARTEx_WakeupCallback() called upon UART wakeup interrupt
+
+
+@endverbatim
+  * @{
+  */
+
+
+
+
+/**
+  * @brief By default in multiprocessor mode, when the wake up method is set
+  *        to address mark, the UART handles only 4-bit long addresses detection;
+  *        this API allows to enable longer addresses detection (6-, 7- or 8-bit
+  *        long).
+  * @note  Addresses detection lengths are: 6-bit address detection in 7-bit data mode, 
+  *        7-bit address detection in 8-bit data mode, 8-bit address detection in 9-bit data mode.
+  * @param huart: UART handle.
+  * @param AddressLength: this parameter can be one of the following values:
+  *          @arg UART_ADDRESS_DETECT_4B: 4-bit long address
+  *          @arg UART_ADDRESS_DETECT_7B: 6-, 7- or 8-bit long address
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_MultiProcessorEx_AddressLength_Set(UART_HandleTypeDef *huart, uint32_t AddressLength)
+{
+  /* Check the UART handle allocation */
+  if(huart == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the address length parameter */
+  assert_param(IS_UART_ADDRESSLENGTH_DETECT(AddressLength));
+
+  huart->State = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the address length */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADDM7, AddressLength);
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* TEACK and/or REACK to check before moving huart->State to Ready */
+  return (UART_CheckIdleState(huart));
+}
+
+
+/**
+  * @brief Set Wakeup from Stop mode interrupt flag selection.
+  * @param huart: UART handle.
+  * @param WakeUpSelection: address match, Start Bit detection or RXNE bit status.
+  * This parameter can be one of the following values:
+  *      @arg UART_WAKEUP_ON_ADDRESS
+  *      @arg UART_WAKEUP_ON_STARTBIT
+  *      @arg UART_WAKEUP_ON_READDATA_NONEMPTY
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_StopModeWakeUpSourceConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection)
+{
+  HAL_StatusTypeDef status = HAL_OK;
+
+  /* check the wake-up from stop mode UART instance */
+  assert_param(IS_UART_WAKEUP_FROMSTOP_INSTANCE(huart->Instance));
+  /* check the wake-up selection parameter */
+  assert_param(IS_UART_WAKEUP_SELECTION(WakeUpSelection.WakeUpEvent));
+
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  huart->State = HAL_UART_STATE_BUSY;
+
+  /* Disable the Peripheral */
+  __HAL_UART_DISABLE(huart);
+
+  /* Set the wake-up selection scheme */
+  MODIFY_REG(huart->Instance->CR3, USART_CR3_WUS, WakeUpSelection.WakeUpEvent);
+
+  if (WakeUpSelection.WakeUpEvent == UART_WAKEUP_ON_ADDRESS)
+  {
+    UARTEx_Wakeup_AddressConfig(huart, WakeUpSelection);
+  }
+
+  /* Enable the Peripheral */
+  __HAL_UART_ENABLE(huart);
+
+  /* Wait until REACK flag is set */
+  if(UART_WaitOnFlagUntilTimeout(huart, USART_ISR_REACK, RESET, HAL_UART_TIMEOUT_VALUE) != HAL_OK)
+  {
+    status = HAL_TIMEOUT;
+  }
+  else
+  {
+    /* Initialize the UART State */
+    huart->State = HAL_UART_STATE_READY;
+  }
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return status;
+}
+
+
+/**
+  * @brief Enable UART Stop Mode.
+  * @note The UART is able to wake up the MCU from Stop 1 mode as long as UART clock is HSI or LSE.
+  * @param huart: UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_EnableStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  huart->State = HAL_UART_STATE_BUSY;
+
+  /* Set UESM bit */
+  SET_BIT(huart->Instance->CR1, USART_CR1_UESM);
+
+  huart->State = HAL_UART_STATE_READY;
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief Disable UART Stop Mode.
+  * @param huart: UART handle.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_UARTEx_DisableStopMode(UART_HandleTypeDef *huart)
+{
+  /* Process Locked */
+  __HAL_LOCK(huart);
+
+  huart->State = HAL_UART_STATE_BUSY;
+
+  /* Clear UESM bit */
+  CLEAR_BIT(huart->Instance->CR1, USART_CR1_UESM);
+
+  huart->State = HAL_UART_STATE_READY;
+
+  /* Process Unlocked */
+  __HAL_UNLOCK(huart);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief UART wakeup from Stop mode callback.
+  * @param huart: UART handle.
+  * @retval None
+  */
+ __weak void HAL_UARTEx_WakeupCallback(UART_HandleTypeDef *huart)
+{
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_UARTEx_WakeupCallback can be implemented in the user file.
+   */
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup UARTEx_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief Initialize the UART wake-up from stop mode parameters when triggered by address detection.
+  * @param huart: UART handle.
+  * @param WakeUpSelection: UART wake up from stop mode parameters.
+  * @retval None
+  */
+static void UARTEx_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection)
+{
+  assert_param(IS_UART_ADDRESSLENGTH_DETECT(WakeUpSelection.AddressLength));
+
+  /* Set the USART address length */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADDM7, WakeUpSelection.AddressLength);
+
+  /* Set the USART address node */
+  MODIFY_REG(huart->Instance->CR2, USART_CR2_ADD, ((uint32_t)WakeUpSelection.Address << UART_CR2_ADDRESS_LSB_POS));
+}
+
+/**
+  * @}
+  */
+
+#endif /* HAL_UART_MODULE_ENABLED */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/