Adam Kucybala
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_tim_ex.c
- Revision:
- 205:c41fc65bcfb4
- Child:
- 218:44081b78fdc2
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F072RB/stm32f0xx_hal_tim_ex.c Thu May 22 20:00:09 2014 +0100
@@ -0,0 +1,1801 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_hal_tim_ex.c
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 20-May-2014
+ * @brief TIM HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Timer extension peripheral:
+ * + Time Hall Sensor Interface Initialization
+ * + Time Hall Sensor Interface Start
+ * + Time Complementary signal bread and dead time configuration
+ * + Time Master and Slave synchronization configuration
+ * + Timer remapping capabilities configuration
+ @verbatim
+ ==============================================================================
+ ##### TIMER Extended features #####
+ ==============================================================================
+ [..]
+ The Timer Extension features include:
+ (#) Complementary outputs with programmable dead-time for :
+ (++) Output Compare
+ (++) PWM generation (Edge and Center-aligned Mode)
+ (++) One-pulse mode output
+ (#) Synchronization circuit to control the timer with external signals and to
+ interconnect several timers together.
+ (#) Break input to put the timer output signals in reset state or in a known state.
+ (#) Supports incremental (quadrature) encoder and hall-sensor circuitry for
+ positioning purposes
+
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+ (#) Initialize the TIM low level resources by implementing the following functions
+ depending from feature used :
+ (++) Complementary Output Compare : HAL_TIM_OC_MspInit()
+ (++) Complementary PWM generation : HAL_TIM_PWM_MspInit()
+ (++) Complementary One-pulse mode output : HAL_TIM_OnePulse_MspInit()
+ (++) Hall Sensor output : HAL_TIM_HallSensor_MspInit()
+
+ (#) Initialize the TIM low level resources :
+ (##) Enable the TIM interface clock using __TIMx_CLK_ENABLE();
+ (##) TIM pins configuration
+ (+++) Enable the clock for the TIM GPIOs using the following function:
+ __GPIOx_CLK_ENABLE();
+ (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init();
+
+ (#) The external Clock can be configured, if needed (the default clock is the
+ internal clock from the APBx), using the following function:
+ HAL_TIM_ConfigClockSource, the clock configuration should be done before
+ any start function.
+
+ (#) Configure the TIM in the desired functioning mode using one of the
+ initialization function of this driver:
+ (++) HAL_TIMEx_HallSensor_Init and HAL_TIMEx_ConfigCommutationEvent: to use the
+ Timer Hall Sensor Interface and the commutation event with the corresponding
+ Interrupt and DMA request if needed (Note that One Timer is used to interface
+ with the Hall sensor Interface and another Timer should be used to use
+ the commutation event).
+
+ (#) Activate the TIM peripheral using one of the start functions:
+ (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT()
+ (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT()
+ (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT()
+ (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT().
+
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+*/
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup TIMEx
+ * @brief TIM HAL module driver
+ * @{
+ */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState);
+
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup TIMEx_Private_Functions
+ * @{
+ */
+
+/** @defgroup TIMEx_Group1 Timer Hall Sensor functions
+ * @brief Timer Hall Sensor functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Hall Sensor functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Initialize and configure TIM HAL Sensor.
+ (+) De-initialize TIM HAL Sensor.
+ (+) Start the Hall Sensor Interface.
+ (+) Stop the Hall Sensor Interface.
+ (+) Start the Hall Sensor Interface and enable interrupts.
+ (+) Stop the Hall Sensor Interface and disable interrupts.
+ (+) Start the Hall Sensor Interface and enable DMA transfers.
+ (+) Stop the Hall Sensor Interface and disable DMA transfers.
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Initializes the TIM Hall Sensor Interface and create the associated handle.
+ * @param htim: TIM Encoder Interface handle
+ * @param sConfig: TIM Hall Sensor configuration structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef* sConfig)
+{
+ TIM_OC_InitTypeDef OC_Config;
+
+ /* Check the TIM handle allocation */
+ if(htim == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
+ assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
+ assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity));
+ assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler));
+ assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter));
+
+ /* Set the TIM state */
+ htim->State= HAL_TIM_STATE_BUSY;
+
+ /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
+ HAL_TIMEx_HallSensor_MspInit(htim);
+
+ /* Configure the Time base in the Encoder Mode */
+ TIM_Base_SetConfig(htim->Instance, &htim->Init);
+
+ /* Configure the Channel 1 as Input Channel to interface with the three Outputs of the Hall sensor */
+ TIM_TI1_SetConfig(htim->Instance, sConfig->IC1Polarity, TIM_ICSELECTION_TRC, sConfig->IC1Filter);
+
+ /* Reset the IC1PSC Bits */
+ htim->Instance->CCMR1 &= (uint16_t)(~TIM_CCMR1_IC1PSC);
+ /* Set the IC1PSC value */
+ htim->Instance->CCMR1 |= sConfig->IC1Prescaler;
+
+ /* Enable the Hall sensor interface (XOR function of the three inputs) */
+ htim->Instance->CR2 |= TIM_CR2_TI1S;
+
+ /* Select the TIM_TS_TI1F_ED signal as Input trigger for the TIM */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_TS);
+ htim->Instance->SMCR |= TIM_TS_TI1F_ED;
+
+ /* Use the TIM_TS_TI1F_ED signal to reset the TIM counter each edge detection */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_SMS);
+ htim->Instance->SMCR |= TIM_SLAVEMODE_RESET;
+
+ /* Program channel 2 in PWM 2 mode with the desired Commutation_Delay*/
+ OC_Config.OCFastMode = TIM_OCFAST_DISABLE;
+ OC_Config.OCIdleState = TIM_OCIDLESTATE_RESET;
+ OC_Config.OCMode = TIM_OCMODE_PWM2;
+ OC_Config.OCNIdleState = TIM_OCNIDLESTATE_RESET;
+ OC_Config.OCNPolarity = TIM_OCNPOLARITY_HIGH;
+ OC_Config.OCPolarity = TIM_OCPOLARITY_HIGH;
+ OC_Config.Pulse = sConfig->Commutation_Delay;
+
+ TIM_OC2_SetConfig(htim->Instance, &OC_Config);
+
+ /* Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2
+ register to 101 */
+ htim->Instance->CR2 &= (uint16_t)(~TIM_CR2_MMS);
+ htim->Instance->CR2 |= TIM_TRGO_OC2REF;
+
+ /* Initialize the TIM state*/
+ htim->State= HAL_TIM_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief DeInitializes the TIM Hall Sensor interface
+ * @param htim: TIM Hall Sensor handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_INSTANCE(htim->Instance));
+
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Disable the TIM Peripheral Clock */
+ __HAL_TIM_DISABLE(htim);
+
+ /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
+ HAL_TIMEx_HallSensor_MspDeInit(htim);
+
+ /* Change TIM state */
+ htim->State = HAL_TIM_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the TIM Hall Sensor MSP.
+ * @param htim: TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_TIMEx_HallSensor_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief DeInitializes TIM Hall Sensor MSP.
+ * @param htim: TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_TIMEx_HallSensor_MspDeInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface.
+ * @param htim : TIM Hall Sensor handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ /* Enable the Input Capture channels 1
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall sensor Interface.
+ * @param htim : TIM Hall Sensor handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channels 1, 2 and 3
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface in interrupt mode.
+ * @param htim : TIM Hall Sensor handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ /* Enable the capture compare Interrupts 1 event */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+ /* Enable the Input Capture channels 1
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall Sensor Interface in interrupt mode.
+ * @param htim : TIM handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channels 1
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+ /* Disable the capture compare Interrupts event */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface in DMA mode.
+ * @param htim : TIM Hall Sensor handle
+ * @param pData: The destination Buffer address.
+ * @param Length: The length of data to be transferred from TIM peripheral to memory.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ if((htim->State == HAL_TIM_STATE_BUSY))
+ {
+ return HAL_BUSY;
+ }
+ else if((htim->State == HAL_TIM_STATE_READY))
+ {
+ if(((uint32_t)pData == 0 ) && (Length > 0))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ /* Enable the Input Capture channels 1
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Set the DMA Input Capture 1 Callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = HAL_TIM_DMACaptureCplt;
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel for Capture 1*/
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length);
+
+ /* Enable the capture compare 1 Interrupt */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall Sensor Interface in DMA mode.
+ * @param htim : TIM handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channels 1
+ (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+
+ /* Disable the capture compare Interrupts 1 event */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Group2 Timer Complementary Output Compare functions
+ * @brief Timer Complementary Output Compare functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary Output Compare functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary Output Compare/PWM.
+ (+) Stop the Complementary Output Compare/PWM.
+ (+) Start the Complementary Output Compare/PWM and enable interrupts.
+ (+) Stop the Complementary Output Compare/PWM and disable interrupts.
+ (+) Start the Complementary Output Compare/PWM and enable DMA transfers.
+ (+) Stop the Complementary Output Compare/PWM and disable DMA transfers.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the TIM Output Compare signal generation on the complementary
+ * output.
+ * @param htim : TIM Output Compare handle
+ * @param Channel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation on the complementary
+ * output.
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Output Compare signal generation in interrupt mode
+ * on the complementary output.
+ * @param htim : TIM OC handle
+ * @param Channel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation in interrupt mode
+ * on the complementary output.
+ * @param htim : TIM Output Compare handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Output Compare signal generation in DMA mode
+ * on the complementary output.
+ * @param htim : TIM Output Compare handle
+ * @param Channel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @param pData: The source Buffer address.
+ * @param Length: The length of data to be transferred from memory to TIM peripheral
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ if((htim->State == HAL_TIM_STATE_BUSY))
+ {
+ return HAL_BUSY;
+ }
+ else if((htim->State == HAL_TIM_STATE_READY))
+ {
+ if(((uint32_t)pData == 0 ) && (Length > 0))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
+
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
+
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+{
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
+
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
+
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation in DMA mode
+ * on the complementary output.
+ * @param htim : TIM Output Compare handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Group3 Timer Complementary PWM functions
+ * @brief Timer Complementary PWM functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary PWM functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary PWM.
+ (+) Stop the Complementary PWM.
+ (+) Start the Complementary PWM and enable interrupts.
+ (+) Stop the Complementary PWM and disable interrupts.
+ (+) Start the Complementary PWM and enable DMA transfers.
+ (+) Stop the Complementary PWM and disable DMA transfers.
+ (+) Start the Complementary Input Capture measurement.
+ (+) Stop the Complementary Input Capture.
+ (+) Start the Complementary Input Capture and enable interrupts.
+ (+) Stop the Complementary Input Capture and disable interrupts.
+ (+) Start the Complementary Input Capture and enable DMA transfers.
+ (+) Stop the Complementary Input Capture and disable DMA transfers.
+ (+) Start the Complementary One Pulse generation.
+ (+) Stop the Complementary One Pulse.
+ (+) Start the Complementary One Pulse and enable interrupts.
+ (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the PWM signal generation on the complementary output.
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the PWM signal generation on the complementary output.
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the PWM signal generation in interrupt mode on the
+ * complementary output.
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Enable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Enable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Enable the TIM Capture/Compare 3 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Enable the TIM Capture/Compare 4 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Enable the TIM Break interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK);
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the PWM signal generation in interrupt mode on the
+ * complementary output.
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Capture/Compare 3 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Disable the TIM Capture/Compare 3 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Disable the TIM Break interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK);
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM PWM signal generation in DMA mode on the
+ * complementary output
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @param pData: The source Buffer address.
+ * @param Length: The length of data to be transferred from memory to TIM peripheral
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ if((htim->State == HAL_TIM_STATE_BUSY))
+ {
+ return HAL_BUSY;
+ }
+ else if((htim->State == HAL_TIM_STATE_READY))
+ {
+ if(((uint32_t)pData == 0 ) && (Length > 0))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
+
+ /* Enable the TIM Capture/Compare 1 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
+
+ /* Enable the TIM Capture/Compare 2 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
+
+ /* Enable the TIM Capture/Compare 3 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Set the DMA Period elapsed callback */
+ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = HAL_TIM_DMADelayPulseCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = HAL_TIM_DMAError ;
+
+ /* Enable the DMA channel */
+ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
+
+ /* Enable the TIM Capture/Compare 4 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral */
+ __HAL_TIM_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM PWM signal generation in DMA mode on the complementary
+ * output
+ * @param htim : TIM handle
+ * @param Channel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @arg TIM_CHANNEL_4: TIM Channel 4 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Capture/Compare 1 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+ }
+ break;
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Capture/Compare 2 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+ }
+ break;
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Capture/Compare 3 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+ }
+ break;
+
+ case TIM_CHANNEL_4:
+ {
+ /* Disable the TIM Capture/Compare 4 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Group4 Timer Complementary One Pulse functions
+ * @brief Timer Complementary One Pulse functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary One Pulse functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary One Pulse generation.
+ (+) Stop the Complementary One Pulse.
+ (+) Start the Complementary One Pulse and enable interrupts.
+ (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the TIM One Pulse signal generation on the complemetary
+ * output.
+ * @param htim : TIM One Pulse handle
+ * @param OutputChannel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+ {
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Enable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM One Pulse signal generation on the complementary
+ * output.
+ * @param htim : TIM One Pulse handle
+ * @param OutputChannel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Disable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM One Pulse signal generation in interrupt mode on the
+ * complementary channel.
+ * @param htim : TIM One Pulse handle
+ * @param OutputChannel : TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Enable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+ /* Enable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+
+ /* Enable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Ouput */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+ }
+
+/**
+ * @brief Stops the TIM One Pulse signal generation in interrupt mode on the
+ * complementary channel.
+ * @param htim : TIM One Pulse handle
+ * @param OutputChannel : TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Disable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+ /* Disable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+
+ /* Disable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Ouput */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+
+
+/**
+ * @}
+ */
+/** @defgroup TIMEx_Group5 Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Peripheral Control functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Configure the commutation event in case of use of the Hall sensor interface.
+ (+) Configure Complementary channels, break features and dead time.
+ (+) Configure Master synchronization.
+ (+) Configure timer remapping capabilities.
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Configure the TIM commutation event sequence.
+ * @note: this function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @param htim: TIM handle
+ * @param InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_NONE: No trigger is needed
+ * @param CommutationSource : the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef *htim, uint32_t InputTrigger, uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_TS);
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= (uint16_t)(~TIM_CR2_CCUS);
+ htim->Instance->CR2 |= CommutationSource;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configure the TIM commutation event sequence with interrupt.
+ * @note: this function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @param htim: TIM handle
+ * @param InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_NONE: No trigger is needed
+ * @param CommutationSource : the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef *htim, uint32_t InputTrigger, uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_TS);
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= (uint16_t)(~TIM_CR2_CCUS);
+ htim->Instance->CR2 |= CommutationSource;
+
+ /* Enable the Commutation Interrupt Request */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_COM);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configure the TIM commutation event sequence with DMA.
+ * @note: this function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @note: The user should configure the DMA in his own software, in This function only the COMDE bit is set
+ * @param htim: TIM handle
+ * @param InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_NONE: No trigger is needed
+ * @param CommutationSource : the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_DMA(TIM_HandleTypeDef *htim, uint32_t InputTrigger, uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_TS);
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= (uint16_t)(~TIM_CR2_CCUS);
+ htim->Instance->CR2 |= CommutationSource;
+
+ /* Enable the Commutation DMA Request */
+ /* Set the DMA Commutation Callback */
+ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = HAL_TIMEx_DMACommutationCplt;
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = HAL_TIM_DMAError;
+
+ /* Enable the Commutation DMA Request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_COM);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the TIM in master mode.
+ * @param htim: TIM handle.
+ * @param sMasterConfig: pointer to a TIM_MasterConfigTypeDef structure that
+ * contains the selected trigger output (TRGO) and the Master/Slave
+ * mode.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim, TIM_MasterConfigTypeDef * sMasterConfig)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_MASTER_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger));
+ assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode));
+
+ __HAL_LOCK(htim);
+
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Reset the MMS Bits */
+ htim->Instance->CR2 &= (uint16_t)(~TIM_CR2_MMS);
+ /* Select the TRGO source */
+ htim->Instance->CR2 |= sMasterConfig->MasterOutputTrigger;
+
+ /* Reset the MSM Bit */
+ htim->Instance->SMCR &= (uint16_t)(~TIM_SMCR_MSM);
+ /* Set or Reset the MSM Bit */
+ htim->Instance->SMCR |= sMasterConfig->MasterSlaveMode;
+
+ htim->State = HAL_TIM_STATE_READY;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State
+ * and the AOE(automatic output enable).
+ * @param htim: TIM handle
+ * @param sBreakDeadTimeConfig: pointer to a TIM_ConfigBreakDeadConfigTypeDef structure that
+ * contains the BDTR Register configuration information for the TIM peripheral.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
+ TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_OSSR_STATE(sBreakDeadTimeConfig->OffStateRunMode));
+ assert_param(IS_TIM_OSSI_STATE(sBreakDeadTimeConfig->OffStateIDLEMode));
+ assert_param(IS_TIM_LOCK_LEVEL(sBreakDeadTimeConfig->LockLevel));
+ assert_param(IS_TIM_BREAK_STATE(sBreakDeadTimeConfig->BreakState));
+ assert_param(IS_TIM_BREAK_POLARITY(sBreakDeadTimeConfig->BreakPolarity));
+ assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(sBreakDeadTimeConfig->AutomaticOutput));
+
+ /* Process Locked */
+ __HAL_LOCK(htim);
+
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State,
+ the OSSI State, the dead time value and the Automatic Output Enable Bit */
+ htim->Instance->BDTR = (uint32_t)sBreakDeadTimeConfig->OffStateRunMode |
+ sBreakDeadTimeConfig->OffStateIDLEMode |
+ sBreakDeadTimeConfig->LockLevel |
+ sBreakDeadTimeConfig->DeadTime |
+ sBreakDeadTimeConfig->BreakState |
+ sBreakDeadTimeConfig->BreakPolarity |
+ sBreakDeadTimeConfig->AutomaticOutput;
+
+
+ htim->State = HAL_TIM_STATE_READY;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the TIM14 Remapping input capabilities.
+ * @param htim: TIM handle.
+ * @param Remap: specifies the TIM remapping source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TIM14_GPIO: TIM14 TI1 is connected to GPIO
+ * @arg TIM_TIM14_RTC: TIM14 TI1 is connected to RTC_clock
+ * @arg TIM_TIM14_HSE: TIM14 TI1 is connected to HSE/32
+ * @arg TIM_TIM14_MCO: TIM14 TI1 is connected to MCO
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap)
+{
+ __HAL_LOCK(htim);
+
+ /* Check parameters */
+ assert_param(IS_TIM_REMAP_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_REMAP(Remap));
+
+ /* Set the Timer remapping configuration */
+ htim->Instance->OR = Remap;
+
+ htim->State = HAL_TIM_STATE_READY;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Group6 Extension Callbacks functions
+ * @brief Extension Callbacks functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Extension Callbacks functions #####
+ ==============================================================================
+ [..]
+ This section provides Extension TIM callback functions:
+ (+) Timer Commutation callback
+ (+) Timer Break callback
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Hall commutation changed callback in non blocking mode
+ * @param htim : TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_CommutationCallback(TIM_HandleTypeDef *htim)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_TIMEx_CommutationCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Hall Break detection callback in non blocking mode
+ * @param htim : TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_TIMEx_BreakCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Group7 Extension Peripheral State functions
+ * @brief Extension Peripheral State functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Extension Peripheral State functions #####
+ ==============================================================================
+ [..]
+ This subsection permit to get in run-time the status of the peripheral
+ and the data flow.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Return the TIM Hall Sensor interface state
+ * @param htim: TIM Hall Sensor handle
+ * @retval HAL state
+ */
+HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim)
+{
+ return htim->State;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @brief TIM DMA Commutation callback.
+ * @param hdma : pointer to DMA handle.
+ * @retval None
+ */
+void HAL_TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma)
+{
+ TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+ htim->State= HAL_TIM_STATE_READY;
+
+ HAL_TIMEx_CommutationCallback(htim);
+}
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel xN.
+ * @param TIMx to select the TIM peripheral
+ * @param Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @param ChannelNState: specifies the TIM Channel CCxNE bit new state.
+ * This parameter can be: TIM_CCxN_ENABLE or TIM_CCxN_Disable.
+ * @retval None
+ */
+static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState)
+{
+ uint32_t tmp = 0;
+
+ tmp = (uint16_t)(TIM_CCER_CC1NE << Channel);
+
+ /* Reset the CCxNE Bit */
+ TIMx->CCER &= (uint16_t)(~tmp);
+
+ /* Set or reset the CCxNE Bit */
+ TIMx->CCER |= (uint16_t)(ChannelNState << Channel);
+}
+
+/**
+ * @}
+ */
+
+#endif /* HAL_TIM_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/