Diff: targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_gpio.c

Revision:

384:ef87175507f1

Parent:

383:0564d9840d0d

Child:

385:be64abf45658

--- a/targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_gpio.c	Mon Nov 03 11:00:07 2014 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,534 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32f4xx_hal_gpio.c
-  * @author  MCD Application Team
-  * @version V1.1.0RC2
-  * @date    14-May-2014
-  * @brief   GPIO HAL module driver.
-  *          This file provides firmware functions to manage the following 
-  *          functionalities of the General Purpose Input/Output (GPIO) peripheral:
-  *           + Initialization and de-initialization functions
-  *           + IO operation functions
-  *
-  @verbatim
-  ==============================================================================
-                    ##### GPIO Peripheral features #####
-  ==============================================================================
-  [..] 
-    (+) Each port bit of the general-purpose I/O (GPIO) ports can be individually 
-        configured by software in several modes:
-        (++) Input mode 
-        (++) Analog mode
-        (++) Output mode
-        (++) Alternate function mode
-        (++) External interrupt/event lines
-
-    (+) During and just after reset, the alternate functions and external interrupt  
-        lines are not active and the I/O ports are configured in input floating mode.
-     
-    (+) All GPIO pins have weak internal pull-up and pull-down resistors, which can be 
-        activated or not.
-
-    (+) In Output or Alternate mode, each IO can be configured on open-drain or push-pull
-        type and the IO speed can be selected depending on the VDD value.
-
-    (+) The microcontroller IO pins are connected to onboard peripherals/modules through a 
-        multiplexer that allows only one peripheral alternate function (AF) connected 
-       to an IO pin at a time. In this way, there can be no conflict between peripherals 
-       sharing the same IO pin. 
-
-    (+) All ports have external interrupt/event capability. To use external interrupt 
-        lines, the port must be configured in input mode. All available GPIO pins are 
-        connected to the 16 external interrupt/event lines from EXTI0 to EXTI15.
-
-    (+) The external interrupt/event controller consists of up to 23 edge detectors 
-        (16 lines are connected to GPIO) for generating event/interrupt requests (each 
-        input line can be independently configured to select the type (interrupt or event) 
-        and the corresponding trigger event (rising or falling or both). Each line can 
-        also be masked independently. 
-
-                     ##### How to use this driver #####
-  ==============================================================================  
-  [..]
-    (#) Enable the GPIO AHB clock using the following function: __GPIOx_CLK_ENABLE(). 
-
-    (#) Configure the GPIO pin(s) using HAL_GPIO_Init().
-        (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure
-        (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef 
-             structure.
-        (++) In case of Output or alternate function mode selection: the speed is 
-             configured through "Speed" member from GPIO_InitTypeDef structure.
-        (++) In alternate mode is selection, the alternate function connected to the IO
-             is configured through "Alternate" member from GPIO_InitTypeDef structure.
-        (++) Analog mode is required when a pin is to be used as ADC channel 
-             or DAC output.
-        (++) In case of external interrupt/event selection the "Mode" member from 
-             GPIO_InitTypeDef structure select the type (interrupt or event) and 
-             the corresponding trigger event (rising or falling or both).
-
-    (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority 
-        mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using
-        HAL_NVIC_EnableIRQ().
-         
-    (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin().
-            
-    (#) To set/reset the level of a pin configured in output mode use 
-        HAL_GPIO_WritePin()/HAL_GPIO_TogglePin().
-                 
-    (#) During and just after reset, the alternate functions are not 
-        active and the GPIO pins are configured in input floating mode (except JTAG
-        pins).
-  
-    (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose 
-        (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has 
-        priority over the GPIO function.
-  
-    (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as 
-        general purpose PH0 and PH1, respectively, when the HSE oscillator is off. 
-        The HSE has priority over the GPIO function.
-  
-  @endverbatim
-  ******************************************************************************
-  * @attention
-  *
-  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
-  *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-  *
-  ******************************************************************************
-  */ 
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f4xx_hal.h"
-
-/** @addtogroup STM32F4xx_HAL_Driver
-  * @{
-  */
-
-/** @defgroup GPIO
-  * @brief GPIO HAL module driver
-  * @{
-  */
-
-#ifdef HAL_GPIO_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-/* Private macro -------------------------------------------------------------*/
-#define __HAL_GET_GPIO_SOURCE(__GPIOx__) \
-(((uint32_t)(__GPIOx__) == ((uint32_t)GPIOA_BASE))? (uint32_t)0 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x0400)))? (uint32_t)1 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x0800)))? (uint32_t)2 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x0C00)))? (uint32_t)3 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x1000)))? (uint32_t)4 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x1400)))? (uint32_t)5 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x1800)))? (uint32_t)6 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x1C00)))? (uint32_t)7 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x2000)))? (uint32_t)8 :\
- ((uint32_t)(__GPIOx__) == ((uint32_t)(GPIOA_BASE + 0x2400)))? (uint32_t)9 : (uint32_t)10)
-
-#define GPIO_MODE             ((uint32_t)0x00000003)
-#define EXTI_MODE             ((uint32_t)0x10000000)
-#define GPIO_MODE_IT          ((uint32_t)0x00010000)
-#define GPIO_MODE_EVT         ((uint32_t)0x00020000)
-#define RISING_EDGE           ((uint32_t)0x00100000)
-#define FALLING_EDGE          ((uint32_t)0x00200000)
-#define GPIO_OUTPUT_TYPE      ((uint32_t)0x00000010)
-
-#define GPIO_NUMBER           ((uint32_t)16)
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/* Private functions ---------------------------------------------------------*/
-
-/** @defgroup GPIO_Private_Functions
-  * @{
-  */
-
-/** @defgroup GPIO_Group1 Initialization and de-initialization functions 
- *  @brief    Initialization and Configuration functions
- *
-@verbatim
- ===============================================================================
-              ##### Initialization and de-initialization functions #####
- ===============================================================================
-
-@endverbatim
-  * @{
-  */
-
-/**
-  * @brief  Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init.
-  * @param  GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
-  *                      x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
-  * @param  GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains
-  *         the configuration information for the specified GPIO peripheral.
-  * @retval None
-  */
-void HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init)
-{
-  uint32_t position;
-  uint32_t ioposition = 0x00;
-  uint32_t iocurrent = 0x00;
-  uint32_t temp = 0x00;
-
-  /* Check the parameters */
-  assert_param(IS_GPIO_PIN(GPIO_Init->Pin));
-  assert_param(IS_GPIO_MODE(GPIO_Init->Mode));
-  assert_param(IS_GPIO_PULL(GPIO_Init->Pull));
-
-  /* Configure the port pins */
-  for(position = 0; position < GPIO_NUMBER; position++)
-  {
-    /* Get the IO position */
-    ioposition = ((uint32_t)0x01) << position;
-    /* Get the current IO position */
-    iocurrent = (uint32_t)(GPIO_Init->Pin) & ioposition;
-
-    if(iocurrent == ioposition)
-    {
-      /*--------------------- GPIO Mode Configuration ------------------------*/
-      /* In case of Alternate function mode selection */
-      if((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
-      {
-        /* Check the Alternate function parameter */
-        assert_param(IS_GPIO_AF(GPIO_Init->Alternate));
-        /* Configure Alternate function mapped with the current IO */
-        temp = GPIOx->AFR[position >> 3];
-        temp &= ~((uint32_t)0xF << ((uint32_t)(position & (uint32_t)0x07) * 4)) ;
-        temp |= ((uint32_t)(GPIO_Init->Alternate) << (((uint32_t)position & (uint32_t)0x07) * 4));
-        GPIOx->AFR[position >> 3] = temp;
-      }
-
-      /* Configure IO Direction mode (Input, Output, Alternate or Analog) */
-      temp = GPIOx->MODER;
-      temp &= ~(GPIO_MODER_MODER0 << (position * 2));
-      temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2));
-      GPIOx->MODER = temp;
-
-      /* In case of Output or Alternate function mode selection */
-      if((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) ||
-         (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
-      {
-        /* Check the Speed parameter */
-        assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));
-        /* Configure the IO Speed */
-        temp = GPIOx->OSPEEDR; 
-        temp &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2));
-        temp |= (GPIO_Init->Speed << (position * 2));
-        GPIOx->OSPEEDR = temp;
-
-        /* Configure the IO Output Type */
-        temp = GPIOx->OTYPER;
-        temp &= ~(GPIO_OTYPER_OT_0 << position) ;
-        temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4) << position);
-        GPIOx->OTYPER = temp;
-      }
-
-      /* Activate the Pull-up or Pull down resistor for the current IO */
-      temp = GPIOx->PUPDR;
-      temp &= ~(GPIO_PUPDR_PUPDR0 << (position * 2));
-      temp |= ((GPIO_Init->Pull) << (position * 2));
-      GPIOx->PUPDR = temp;
-
-      /*--------------------- EXTI Mode Configuration ------------------------*/
-      /* Configure the External Interrupt or event for the current IO */
-      if((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE)
-      {
-        /* Enable SYSCFG Clock */
-        __SYSCFG_CLK_ENABLE();
-
-        temp = SYSCFG->EXTICR[position >> 2];
-        temp &= ~(((uint32_t)0x0F) << (4 * (position & 0x03)));
-        temp |= ((uint32_t)(__HAL_GET_GPIO_SOURCE(GPIOx)) << (4 * (position & 0x03)));
-        SYSCFG->EXTICR[position >> 2] = temp;
-
-        /* Clear EXTI line configuration */
-        temp = EXTI->IMR;
-        temp &= ~((uint32_t)iocurrent);
-        if((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT)
-        {
-          temp |= iocurrent;
-        }
-        EXTI->IMR = temp;
-
-        temp = EXTI->EMR;
-        temp &= ~((uint32_t)iocurrent);
-        if((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT)
-        {
-          temp |= iocurrent;
-        }
-        EXTI->EMR = temp;
-
-        /* Clear Rising Falling edge configuration */
-        temp = EXTI->RTSR;
-        temp &= ~((uint32_t)iocurrent);
-        if((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE)
-        {
-          temp |= iocurrent;
-        }
-        EXTI->RTSR = temp;
-
-        temp = EXTI->FTSR;
-        temp &= ~((uint32_t)iocurrent);
-        if((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE)
-        {
-          temp |= iocurrent;
-        }
-        EXTI->FTSR = temp;
-      }
-    }
-  }
-}
-
-/**
-  * @brief  De-initializes the GPIOx peripheral registers to their default reset values.
-  * @param  GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
-  *                      x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
-  * @param  GPIO_Pin: specifies the port bit to be written.
-  *          This parameter can be one of GPIO_PIN_x where x can be (0..15).
-  * @retval None
-  */
-void HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin)
-{
-  uint32_t position;
-  uint32_t ioposition = 0x00;
-  uint32_t iocurrent = 0x00;
-  uint32_t tmp = 0x00;
-
-  /* Configure the port pins */
-  for(position = 0; position < GPIO_NUMBER; position++)
-  {
-    /* Get the IO position */
-    ioposition = ((uint32_t)0x01) << position;
-    /* Get the current IO position */
-    iocurrent = (GPIO_Pin) & ioposition;
-
-    if(iocurrent == ioposition)
-    {
-      /*------------------------- GPIO Mode Configuration --------------------*/
-      /* Configure IO Direction in Input Floting Mode */
-      GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (position * 2));
-
-      /* Configure the default Alternate Function in current IO */
-      GPIOx->AFR[position >> 3] &= ~((uint32_t)0xF << ((uint32_t)(position & (uint32_t)0x07) * 4)) ;
-
-      /* Configure the default value for IO Speed */
-      GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2));
-
-      /* Configure the default value IO Output Type */
-      GPIOx->OTYPER  &= ~(GPIO_OTYPER_OT_0 << position) ;
-
-      /* Deactivate the Pull-up oand Pull-down resistor for the current IO */
-      GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << (position * 2));
-
-      /*------------------------- EXTI Mode Configuration --------------------*/
-      /* Configure the External Interrupt or event for the current IO */
-      tmp = ((uint32_t)0x0F) << (4 * (position & 0x03));
-      SYSCFG->EXTICR[position >> 2] &= ~tmp;
-
-      /* Clear EXTI line configuration */
-      EXTI->IMR &= ~((uint32_t)iocurrent);
-      EXTI->EMR &= ~((uint32_t)iocurrent);
-
-      /* Clear Rising Falling edge configuration */
-      EXTI->RTSR &= ~((uint32_t)iocurrent);
-      EXTI->FTSR &= ~((uint32_t)iocurrent);
-    }
-  }
-}
-
-/**
-  * @}
-  */
-
-/** @defgroup GPIO_Group2 IO operation functions 
- *  @brief   GPIO Read and Write
- *
-@verbatim
- ===============================================================================
-                       ##### IO operation functions #####
- ===============================================================================
-
-@endverbatim
-  * @{
-  */
-
-/**
-  * @brief  Reads the specified input port pin.
-  * @param  GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
-  *                      x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
-  * @param  GPIO_Pin: specifies the port bit to read.
-  *         This parameter can be GPIO_PIN_x where x can be (0..15).
-  * @retval The input port pin value.
-  */
-GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
-{
-  GPIO_PinState bitstatus;
-
-  /* Check the parameters */
-  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
-
-  if((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET)
-  {
-    bitstatus = GPIO_PIN_SET;
-  }
-  else
-  {
-    bitstatus = GPIO_PIN_RESET;
-  }
-  return bitstatus;
-}
-
-/**
-  * @brief  Sets or clears the selected data port bit.
-  *
-  * @note   This function uses GPIOx_BSRR register to allow atomic read/modify
-  *         accesses. In this way, there is no risk of an IRQ occurring between
-  *         the read and the modify access.
-  *
-  * @param  GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
-  *                      x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
-  * @param  GPIO_Pin: specifies the port bit to be written.
-  *          This parameter can be one of GPIO_PIN_x where x can be (0..15).
-  * @param  PinState: specifies the value to be written to the selected bit.
-  *          This parameter can be one of the GPIO_PinState enum values:
-  *            @arg GPIO_PIN_RESET: to clear the port pin
-  *            @arg GPIO_PIN_SET: to set the port pin
-  * @retval None
-  */
-void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)
-{
-  /* Check the parameters */
-  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
-  assert_param(IS_GPIO_PIN_ACTION(PinState));
-
-  if(PinState != GPIO_PIN_RESET)
-  {
-    GPIOx->BSRRL = GPIO_Pin;
-  }
-  else
-  {
-    GPIOx->BSRRH = GPIO_Pin ;
-  }
-}
-
-/**
-  * @brief  Toggles the specified GPIO pins.
-  * @param  GPIOx: Where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
-  *                      x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
-  * @param  GPIO_Pin: Specifies the pins to be toggled.
-  * @retval None
-  */
-void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
-{
-  /* Check the parameters */
-  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
-
-  GPIOx->ODR ^= GPIO_Pin;
-}
-
-/**
-  * @brief  Locks GPIO Pins configuration registers.
-  * @note   The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
-  *         GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
-  * @note   The configuration of the locked GPIO pins can no longer be modified
-  *         until the next reset.
-  * @param  GPIOx: where x can be (A..F) to select the GPIO peripheral for STM32F4 family
-  * @param  GPIO_Pin: specifies the port bit to be locked.
-  *         This parameter can be any combination of GPIO_PIN_x where x can be (0..15).
-  * @retval None
-  */
-HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
-{
-  __IO uint32_t tmp = GPIO_LCKR_LCKK;
-
-  /* Check the parameters */
-  assert_param(IS_GPIO_PIN(GPIO_Pin));
-
-  /* Apply lock key write sequence */
-  tmp |= GPIO_Pin;
-  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
-  GPIOx->LCKR = tmp;
-  /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */
-  GPIOx->LCKR = GPIO_Pin;
-  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
-  GPIOx->LCKR = tmp;
-  /* Read LCKK bit*/
-  tmp = GPIOx->LCKR;
-
-  if(GPIOx->LCKR & GPIO_LCKR_LCKK)
-  {
-    return HAL_OK;
-  }
-  else
-  {
-    return HAL_ERROR;
-  }
-}
-
-/**
-  * @brief  This function handles EXTI interrupt request.
-  * @param  GPIO_Pin: Specifies the pins connected EXTI line
-  * @retval None
-  */
-void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin)
-{
-  /* EXTI line interrupt detected */
-  if(__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != RESET)
-  {
-    __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin);
-    HAL_GPIO_EXTI_Callback(GPIO_Pin);
-  }
-}
-
-/**
-  * @brief  EXTI line detection callbacks.
-  * @param  GPIO_Pin: Specifies the pins connected EXTI line
-  * @retval None
-  */
-__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
-{
-  /* NOTE: This function Should not be modified, when the callback is needed,
-           the HAL_GPIO_EXTI_Callback could be implemented in the user file
-   */
-}
-
-/**
-  * @}
-  */
-
-
-/**
-  * @}
-  */
-
-#endif /* HAL_GPIO_MODULE_ENABLED */
-/**
-  * @}
-  */
-
-/**
-  * @}
-  */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/