Stuart Northfield
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_conf.h
- Revision:
- 384:ef87175507f1
- Parent:
- 383:0564d9840d0d
- Child:
- 385:be64abf45658
--- a/targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_conf.h Mon Nov 03 11:00:07 2014 +0000
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,400 +0,0 @@
-/**
- ******************************************************************************
- * @file stm32f4xx_hal_conf_template.h
- * @author MCD Application Team
- * @version V1.1.0RC2
- * @date 14-May-2014
- * @brief HAL configuration template file.
- * This file should be copied to the application folder and renamed
- * to stm32f4xx_hal_conf.h.
- ******************************************************************************
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __STM32F4xx_HAL_CONF_H
-#define __STM32F4xx_HAL_CONF_H
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-/* Exported types ------------------------------------------------------------*/
-/* Exported constants --------------------------------------------------------*/
-
-/* ########################## Module Selection ############################## */
-/**
- * @brief This is the list of modules to be used in the HAL driver
- */
-#define HAL_MODULE_ENABLED
-#define HAL_ADC_MODULE_ENABLED
-#define HAL_CAN_MODULE_ENABLED
-#define HAL_CRC_MODULE_ENABLED
-#define HAL_CRYP_MODULE_ENABLED
-#define HAL_DAC_MODULE_ENABLED
-#define HAL_DCMI_MODULE_ENABLED
-#define HAL_DMA_MODULE_ENABLED
-#define HAL_DMA2D_MODULE_ENABLED
-#define HAL_ETH_MODULE_ENABLED
-#define HAL_FLASH_MODULE_ENABLED
-#define HAL_NAND_MODULE_ENABLED
-#define HAL_NOR_MODULE_ENABLED
-#define HAL_PCCARD_MODULE_ENABLED
-#define HAL_SRAM_MODULE_ENABLED
-#define HAL_SDRAM_MODULE_ENABLED
-#define HAL_HASH_MODULE_ENABLED
-#define HAL_GPIO_MODULE_ENABLED
-#define HAL_I2C_MODULE_ENABLED
-#define HAL_I2S_MODULE_ENABLED
-#define HAL_IWDG_MODULE_ENABLED
-#define HAL_LTDC_MODULE_ENABLED
-#define HAL_PWR_MODULE_ENABLED
-#define HAL_RCC_MODULE_ENABLED
-//#define HAL_RNG_MODULE_ENABLED
-#define HAL_RTC_MODULE_ENABLED
-#define HAL_SAI_MODULE_ENABLED
-#define HAL_SD_MODULE_ENABLED
-#define HAL_SPI_MODULE_ENABLED
-#define HAL_TIM_MODULE_ENABLED
-#define HAL_UART_MODULE_ENABLED
-#define HAL_USART_MODULE_ENABLED
-#define HAL_IRDA_MODULE_ENABLED
-#define HAL_SMARTCARD_MODULE_ENABLED
-#define HAL_WWDG_MODULE_ENABLED
-#define HAL_CORTEX_MODULE_ENABLED
-#define HAL_PCD_MODULE_ENABLED
-#define HAL_HCD_MODULE_ENABLED
-
-
-/* ########################## HSE/HSI Values adaptation ##################### */
-/**
- * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
- * This value is used by the RCC HAL module to compute the system frequency
- * (when HSE is used as system clock source, directly or through the PLL).
- */
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSE_STARTUP_TIMEOUT)
- #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
-#endif /* HSE_STARTUP_TIMEOUT */
-
-/**
- * @brief Internal High Speed oscillator (HSI) value.
- * This value is used by the RCC HAL module to compute the system frequency
- * (when HSI is used as system clock source, directly or through the PLL).
- */
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @brief External Low Speed oscillator (LSE) value.
- * This value is used by the UART, RTC HAL module to compute the system frequency
- */
-#if !defined (LSE_VALUE)
- #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
-#endif /* LSE_VALUE */
-
-/**
- * @brief External clock source for I2S peripheral
- * This value is used by the I2S HAL module to compute the I2S clock source
- * frequency, this source is inserted directly through I2S_CKIN pad.
- */
-#if !defined (EXTERNAL_CLOCK_VALUE)
- #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the external oscillator in Hz*/
-#endif /* EXTERNAL_CLOCK_VALUE */
-
-/* Tip: To avoid modifying this file each time you need to use different HSE,
- === you can define the HSE value in your toolchain compiler preprocessor. */
-
-/* ########################### System Configuration ######################### */
-/**
- * @brief This is the HAL system configuration section
- */
-#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
-#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */
-#define USE_RTOS 0
-#define PREFETCH_ENABLE 1
-#define INSTRUCTION_CACHE_ENABLE 1
-#define DATA_CACHE_ENABLE 1
-
-/* ########################## Assert Selection ############################## */
-/**
- * @brief Uncomment the line below to expanse the "assert_param" macro in the
- * HAL drivers code
- */
-/* #define USE_FULL_ASSERT 1 */
-
-/* ################## Ethernet peripheral configuration ##################### */
-
-/* Section 1 : Ethernet peripheral configuration */
-
-/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
-#define MAC_ADDR0 2
-#define MAC_ADDR1 0
-#define MAC_ADDR2 0
-#define MAC_ADDR3 0
-#define MAC_ADDR4 0
-#define MAC_ADDR5 0
-
-/* Definition of the Ethernet driver buffers size and count */
-#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
-#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
-#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
-#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
-
-/* Section 2: PHY configuration section */
-
-/* DP83848 PHY Address*/
-#define DP83848_PHY_ADDRESS 0x01
-/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
-#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
-/* PHY Configuration delay */
-#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
-
-#define PHY_READ_TO ((uint32_t)0x0000FFFF)
-#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
-
-/* Section 3: Common PHY Registers */
-
-#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
-#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
-
-#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
-#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
-#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
-#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
-#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
-#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
-#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
-#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
-#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
-#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
-
-#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
-#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
-#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
-
-/* Section 4: Extended PHY Registers */
-
-#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
-#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
-#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
-
-#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
-#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
-#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
-
-#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
-#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
-
-#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
-#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
-
-/* Includes ------------------------------------------------------------------*/
-/**
- * @brief Include module's header file
- */
-
-#ifdef HAL_RCC_MODULE_ENABLED
- #include "stm32f4xx_hal_rcc.h"
-#endif /* HAL_RCC_MODULE_ENABLED */
-
-#ifdef HAL_GPIO_MODULE_ENABLED
- #include "stm32f4xx_hal_gpio.h"
-#endif /* HAL_GPIO_MODULE_ENABLED */
-
-#ifdef HAL_DMA_MODULE_ENABLED
- #include "stm32f4xx_hal_dma.h"
-#endif /* HAL_DMA_MODULE_ENABLED */
-
-#ifdef HAL_CORTEX_MODULE_ENABLED
- #include "stm32f4xx_hal_cortex.h"
-#endif /* HAL_CORTEX_MODULE_ENABLED */
-
-#ifdef HAL_ADC_MODULE_ENABLED
- #include "stm32f4xx_hal_adc.h"
-#endif /* HAL_ADC_MODULE_ENABLED */
-
-#ifdef HAL_CAN_MODULE_ENABLED
- #include "stm32f4xx_hal_can.h"
-#endif /* HAL_CAN_MODULE_ENABLED */
-
-#ifdef HAL_CRC_MODULE_ENABLED
- #include "stm32f4xx_hal_crc.h"
-#endif /* HAL_CRC_MODULE_ENABLED */
-
-#ifdef HAL_CRYP_MODULE_ENABLED
- #include "stm32f4xx_hal_cryp.h"
-#endif /* HAL_CRYP_MODULE_ENABLED */
-
-#ifdef HAL_DMA2D_MODULE_ENABLED
- #include "stm32f4xx_hal_dma2d.h"
-#endif /* HAL_DMA2D_MODULE_ENABLED */
-
-#ifdef HAL_DAC_MODULE_ENABLED
- #include "stm32f4xx_hal_dac.h"
-#endif /* HAL_DAC_MODULE_ENABLED */
-
-#ifdef HAL_DCMI_MODULE_ENABLED
- #include "stm32f4xx_hal_dcmi.h"
-#endif /* HAL_DCMI_MODULE_ENABLED */
-
-#ifdef HAL_ETH_MODULE_ENABLED
- #include "stm32f4xx_hal_eth.h"
-#endif /* HAL_ETH_MODULE_ENABLED */
-
-#ifdef HAL_FLASH_MODULE_ENABLED
- #include "stm32f4xx_hal_flash.h"
-#endif /* HAL_FLASH_MODULE_ENABLED */
-
-#ifdef HAL_SRAM_MODULE_ENABLED
- #include "stm32f4xx_hal_sram.h"
-#endif /* HAL_SRAM_MODULE_ENABLED */
-
-#ifdef HAL_NOR_MODULE_ENABLED
- #include "stm32f4xx_hal_nor.h"
-#endif /* HAL_NOR_MODULE_ENABLED */
-
-#ifdef HAL_NAND_MODULE_ENABLED
- #include "stm32f4xx_hal_nand.h"
-#endif /* HAL_NAND_MODULE_ENABLED */
-
-#ifdef HAL_PCCARD_MODULE_ENABLED
- #include "stm32f4xx_hal_pccard.h"
-#endif /* HAL_PCCARD_MODULE_ENABLED */
-
-#ifdef HAL_SDRAM_MODULE_ENABLED
- #include "stm32f4xx_hal_sdram.h"
-#endif /* HAL_SDRAM_MODULE_ENABLED */
-
-#ifdef HAL_HASH_MODULE_ENABLED
- #include "stm32f4xx_hal_hash.h"
-#endif /* HAL_HASH_MODULE_ENABLED */
-
-#ifdef HAL_I2C_MODULE_ENABLED
- #include "stm32f4xx_hal_i2c.h"
-#endif /* HAL_I2C_MODULE_ENABLED */
-
-#ifdef HAL_I2S_MODULE_ENABLED
- #include "stm32f4xx_hal_i2s.h"
-#endif /* HAL_I2S_MODULE_ENABLED */
-
-#ifdef HAL_IWDG_MODULE_ENABLED
- #include "stm32f4xx_hal_iwdg.h"
-#endif /* HAL_IWDG_MODULE_ENABLED */
-
-#ifdef HAL_LTDC_MODULE_ENABLED
- #include "stm32f4xx_hal_ltdc.h"
-#endif /* HAL_LTDC_MODULE_ENABLED */
-
-#ifdef HAL_PWR_MODULE_ENABLED
- #include "stm32f4xx_hal_pwr.h"
-#endif /* HAL_PWR_MODULE_ENABLED */
-
-#ifdef HAL_RNG_MODULE_ENABLED
- #include "stm32f4xx_hal_rng.h"
-#endif /* HAL_RNG_MODULE_ENABLED */
-
-#ifdef HAL_RTC_MODULE_ENABLED
- #include "stm32f4xx_hal_rtc.h"
-#endif /* HAL_RTC_MODULE_ENABLED */
-
-#ifdef HAL_SAI_MODULE_ENABLED
- #include "stm32f4xx_hal_sai.h"
-#endif /* HAL_SAI_MODULE_ENABLED */
-
-#ifdef HAL_SD_MODULE_ENABLED
- #include "stm32f4xx_hal_sd.h"
-#endif /* HAL_SD_MODULE_ENABLED */
-
-#ifdef HAL_SPI_MODULE_ENABLED
- #include "stm32f4xx_hal_spi.h"
-#endif /* HAL_SPI_MODULE_ENABLED */
-
-#ifdef HAL_TIM_MODULE_ENABLED
- #include "stm32f4xx_hal_tim.h"
-#endif /* HAL_TIM_MODULE_ENABLED */
-
-#ifdef HAL_UART_MODULE_ENABLED
- #include "stm32f4xx_hal_uart.h"
-#endif /* HAL_UART_MODULE_ENABLED */
-
-#ifdef HAL_USART_MODULE_ENABLED
- #include "stm32f4xx_hal_usart.h"
-#endif /* HAL_USART_MODULE_ENABLED */
-
-#ifdef HAL_IRDA_MODULE_ENABLED
- #include "stm32f4xx_hal_irda.h"
-#endif /* HAL_IRDA_MODULE_ENABLED */
-
-#ifdef HAL_SMARTCARD_MODULE_ENABLED
- #include "stm32f4xx_hal_smartcard.h"
-#endif /* HAL_SMARTCARD_MODULE_ENABLED */
-
-#ifdef HAL_WWDG_MODULE_ENABLED
- #include "stm32f4xx_hal_wwdg.h"
-#endif /* HAL_WWDG_MODULE_ENABLED */
-
-#ifdef HAL_PCD_MODULE_ENABLED
- #include "stm32f4xx_hal_pcd.h"
-#endif /* HAL_PCD_MODULE_ENABLED */
-
-#ifdef HAL_HCD_MODULE_ENABLED
- #include "stm32f4xx_hal_hcd.h"
-#endif /* HAL_HCD_MODULE_ENABLED */
-
-/* Exported macro ------------------------------------------------------------*/
-#ifdef USE_FULL_ASSERT
-/**
- * @brief The assert_param macro is used for function's parameters check.
- * @param expr: If expr is false, it calls assert_failed function
- * which reports the name of the source file and the source
- * line number of the call that failed.
- * If expr is true, it returns no value.
- * @retval None
- */
- #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
-/* Exported functions ------------------------------------------------------- */
- void assert_failed(uint8_t* file, uint32_t line);
-#else
- #define assert_param(expr) ((void)0)
-#endif /* USE_FULL_ASSERT */
-
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __STM32F4xx_HAL_CONF_H */
-
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
