Stuart Northfield
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_STM32L1/stm32l1xx_hal_rcc.c
- Revision:
- 394:83f921546702
- Parent:
- 354:e67efb2aab0e
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_STM32L1/stm32l1xx_hal_rcc.c Fri Nov 07 15:45:07 2014 +0000
@@ -0,0 +1,1313 @@
+/**
+ ******************************************************************************
+ * @file stm32l1xx_hal_rcc.c
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 5-September-2014
+ * @brief RCC HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Reset and Clock Control (RCC) peripheral:
+ * + Initialization and de-initialization functions
+ * + Peripheral Control functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### RCC specific features #####
+ ==============================================================================
+ [..]
+ After reset the device is running from multispeed internal oscillator clock
+ (MSI 2.097MHz) with Flash 0 wait state and Flash prefetch buffer is disabled,
+ and all peripherals are off except internal SRAM, Flash and JTAG.
+ (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses;
+ all peripherals mapped on these busses are running at MSI speed.
+ (+) The clock for all peripherals is switched off, except the SRAM and FLASH.
+ (+) All GPIOs are in input floating state, except the JTAG pins which
+ are assigned to be used for debug purpose.
+ [..] Once the device started from reset, the user application has to:
+ (+) Configure the clock source to be used to drive the System clock
+ (if the application needs higher frequency/performance)
+ (+) Configure the System clock frequency and Flash settings
+ (+) Configure the AHB and APB busses prescalers
+ (+) Enable the clock for the peripheral(s) to be used
+ (+) Configure the clock source(s) for peripherals whose clocks are not
+ derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG)
+ (*) SDIO only for STM32L1xxxD devices
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+*/
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l1xx_hal.h"
+
+/** @addtogroup STM32L1xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup RCC RCC
+* @brief RCC HAL module driver
+ * @{
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup RCC_Private_Defines RCC Private Defines
+ * @{
+ */
+
+#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT
+#define MSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
+#define HSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
+#define LSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
+#define PLL_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
+#define CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000) /* 5 s */
+
+/**
+ * @}
+ */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup RCC_Private_Macros RCC Private Macros
+ * @{
+ */
+
+#define __MCO1_CLK_ENABLE() __GPIOA_CLK_ENABLE()
+#define MCO1_GPIO_PORT GPIOA
+#define MCO1_PIN GPIO_PIN_8
+
+/**
+ * @}
+ */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup RCC_Private_Variables RCC Private Variables
+ * @{
+ */
+const uint8_t aAPBAHBPrescTable[16] = {0, 0, 0, 0, 1, 2, 3, 4, 1, 2, 3, 4, 6, 7, 8, 9};
+const uint8_t aPLLDivisionFactorTable[4] = {1, 2, 3, 4};
+const uint8_t aPLLMulFactorTable[9] = {3, 4, 6, 8, 12, 16, 24, 32, 48};
+
+/**
+ * @}
+ */
+
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RCC_Private_Functions RCC Exported Functions
+ * @{
+ */
+
+/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+ @verbatim
+ ===============================================================================
+##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..]
+ This section provides functions allowing to configure the internal/external oscillators
+ (MSI, HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, AHB, APB1
+ and APB2).
+
+ [..] Internal/external clock and PLL configuration
+ (#) MSI (Multispeed internal), Seven frequency ranges are available: 65.536 kHz,
+ 131.072 kHz, 262.144 kHz, 524.288 kHz, 1.048 MHz, 2.097 MHz (default value) and 4.194 MHz.
+
+ (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through
+ the PLL as System clock source.
+
+ (#) LSI (low-speed internal), ~37 KHz low consumption RC used as IWDG and/or RTC
+ clock source.
+
+ (#) HSE (high-speed external), 1 to 24 MHz crystal oscillator used directly or
+ through the PLL as System clock source. Can be used also as RTC clock source.
+
+ (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source.
+
+ (#) PLL (clocked by HSI or HSE), featuring two different output clocks:
+ (++) The first output is used to generate the high speed system clock (up to 32 MHz)
+ (++) The second output is used to generate the clock for the USB OTG FS (48 MHz)
+
+ (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE()
+ and if a HSE clock failure occurs(HSE used directly or through PLL as System
+ clock source), the System clockis automatically switched to MSI and an interrupt
+ is generated if enabled. The interrupt is linked to the Cortex-M3 NMI
+ (Non-Maskable Interrupt) exception vector.
+
+ (#) MCO1 (microcontroller clock output), used to output SYSCLK, HSI, LSI, MSI, LSE,
+ HSE or PLL clock (through a configurable prescaler) on PA8 pin.
+
+ [..] System, AHB and APB busses clocks configuration
+ (#) Several clock sources can be used to drive the System clock (SYSCLK): MSI, HSI,
+ HSE and PLL.
+ The AHB clock (HCLK) is derived from System clock through configurable
+ prescaler and used to clock the CPU, memory and peripherals mapped
+ on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived
+ from AHB clock through configurable prescalers and used to clock
+ the peripherals mapped on these busses. You can use
+ "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
+
+ -@- All the peripheral clocks are derived from the System clock (SYSCLK) except:
+ (+@) RTC: RTC clock can be derived either from the LSI, LSE or HSE clock
+ divided by 2 to 16. You have to use __HAL_RCC_RTC_CONFIG() and __HAL_RCC_RTC_ENABLE()
+ macros to configure this clock.
+ (+@) LCD: LCD clock can be derived either from the LSI, LSE or HSE clock
+ divided by 2 to 16. You have to use __HAL_RCC_LCD_CONFIG()
+ macros to configure this clock.
+ (+@) USB OTG FS and RTC: USB OTG FS require a frequency equal to 48 MHz
+ to work correctly. This clock is derived of the main PLL through PLL Multiplier.
+ (+@) IWDG clock which is always the LSI clock.
+
+ (#) The maximum frequency of the SYSCLK and HCLK is 32 MHz, PCLK2 32 MHz
+ and PCLK1 32 MHz. Depending on the device voltage range, the maximum
+ frequency should be adapted accordingly:
+ +----------------------------------------------------------------------+
+ | Latency | HCLK clock frequency (MHz) |
+ | |------------------------------------------------------|
+ | | voltage range 1 | voltage range 2 | voltage range 3 |
+ | | 1.8 V | 1.5 V | 1.2 V |
+ |---------------|------------------|-----------------|-----------------|
+ |0WS(1CPU cycle)| 0 < HCLK <= 16 | 0 < HCLK <= 8 | 0 < HCLK <= 2 |
+ |---------------|------------------|-----------------|-----------------|
+ |1WS(2CPU cycle)| 16 < HCLK <= 32 | 8 < HCLK <= 16 | 2 < HCLK <= 4 |
+ +----------------------------------------------------------------------+
+ (#) The following table gives the different clock source frequencies depending on the product
+ voltage range:
+ +------------------------------------------------------------------------------------------+
+ | Product voltage | Clock frequency |
+ | |------------------|-----------------------------|-----------------------|
+ | range | MSI | HSI | HSE | PLL |
+ |-----------------|---------|--------|-----------------------------|-----------------------|
+ | Range 1 (1.8 V) | 4.2 MHz | 16 MHz | HSE 32 MHz (external clock) | 32 MHz |
+ | | | | or 24 MHz (crystal) | (PLLVCO max = 96 MHz) |
+ |-----------------|---------|--------|-----------------------------|-----------------------|
+ | Range 2 (1.5 V) | 4.2 MHz | 16 MHz | 16 MHz | 16 MHz |
+ | | | | | (PLLVCO max = 48 MHz) |
+ |-----------------|---------|--------|-----------------------------|-----------------------|
+ | Range 3 (1.2 V) | 4.2 MHz | NA | 8 MHz | 4 MHz |
+ | | | | | (PLLVCO max = 24 MHz) |
+ +------------------------------------------------------------------------------------------+
+
+ @endverbatim
+ * @{
+ */
+
+/**
+ * @brief Resets the RCC clock configuration to the default reset state.
+ * @note The default reset state of the clock configuration is given below:
+ * - MSI ON and used as system clock source
+ * - HSI, HSE and PLL OFF
+ * - AHB, APB1 and APB2 prescaler set to 1.
+ * - CSS and MCO1 OFF
+ * - All interrupts disabled
+ * @note This function doesn't modify the configuration of the
+ * - Peripheral clocks
+ * - LSI, LSE and RTC clocks
+ * @retval None
+ */
+void HAL_RCC_DeInit(void)
+{
+ /* Set MSION bit */
+ SET_BIT(RCC->CR, RCC_CR_MSION);
+
+ /* Switch SYSCLK to MSI*/
+ CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW);
+
+ /* Reset HSION, HSEON, CSSON, HSEBYP & PLLON bits */
+ CLEAR_BIT(RCC->CR, RCC_CR_HSION | RCC_CR_HSEON | RCC_CR_CSSON | RCC_CR_PLLON | RCC_CR_HSEBYP);
+
+ /* Reset CFGR register */
+ CLEAR_REG(RCC->CFGR);
+
+ /* Set MSIClockRange & MSITRIM[4:0] bits to the reset value */
+ MODIFY_REG(RCC->ICSCR, (RCC_ICSCR_MSIRANGE | RCC_ICSCR_MSITRIM), (((uint32_t)0 << POSITION_VAL(RCC_ICSCR_MSITRIM)) | RCC_ICSCR_MSIRANGE_5));
+
+ /* Set HSITRIM bits to the reset value */
+ MODIFY_REG(RCC->ICSCR, RCC_ICSCR_HSITRIM, ((uint32_t)0x10 << POSITION_VAL(RCC_ICSCR_HSITRIM)));
+
+ /* Disable all interrupts */
+ CLEAR_REG(RCC->CIR);
+}
+
+/**
+ * @brief Initializes the RCC Oscillators according to the specified parameters in the
+ * RCC_OscInitTypeDef.
+ * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that
+ * contains the configuration information for the RCC Oscillators.
+ * @note The PLL is not disabled when used as system clock.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
+{
+ uint32_t tickstart = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType));
+
+ /*------------------------------- HSE Configuration ------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState));
+ /* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */
+ if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE)
+ || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE)))
+ {
+ if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState != RCC_HSE_ON))
+ {
+ return HAL_ERROR;
+ }
+ }
+ else
+ {
+ /* Reset HSEON and HSEBYP bits before configuring the HSE --------------*/
+ __HAL_RCC_HSE_CONFIG(RCC_HSE_OFF);
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSE is disabled */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Set the new HSE configuration ---------------------------------------*/
+ __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState);
+
+ /* Check the HSE State */
+ if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF)
+ {
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSE is bypassed or disabled */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /*----------------------------- HSI Configuration --------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState));
+ assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue));
+
+ /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */
+ if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI)
+ || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI)))
+ {
+ /* When HSI is used as system clock it will not disabled */
+ if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON))
+ {
+ return HAL_ERROR;
+ }
+ /* Otherwise, just the calibration is allowed */
+ else
+ {
+ /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
+ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+ }
+ }
+ else
+ {
+ /* Check the HSI State */
+ if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF)
+ {
+ /* Enable the Internal High Speed oscillator (HSI). */
+ __HAL_RCC_HSI_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
+ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+ }
+ else
+ {
+ /* Disable the Internal High Speed oscillator (HSI). */
+ __HAL_RCC_HSI_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /*----------------------------- MSI Configuration --------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_MSI(RCC_OscInitStruct->MSIState));
+ assert_param(IS_RCC_MSIRANGE(RCC_OscInitStruct->MSIClockRange));
+
+ /* Configures the Internal Multi Speed oscillator (MSI) clock range. */
+ __HAL_RCC_MSI_RANGE_CONFIG(RCC_OscInitStruct->MSIClockRange);
+
+ /* Check if MSI is used as system clock */
+ if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_MSI))
+ {
+ /* When MSI is used as system clock it will not disabled */
+ if((__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != RESET) && (RCC_OscInitStruct->MSIState != RCC_MSI_ON))
+ {
+ return HAL_ERROR;
+ }
+ /* Otherwise, just the calibration is allowed */
+ else
+ {
+ /* Adjusts the Multi Speed oscillator (MSI) calibration value. */
+ __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue);
+ }
+ }
+ else
+ {
+ /* Check the MSI State */
+ if((RCC_OscInitStruct->MSIState)!= RCC_MSI_OFF)
+ {
+ /* Enable the Multi Speed oscillator (MSI). */
+ __HAL_RCC_MSI_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till MSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > MSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Adjusts the Multi Speed oscillator (MSI) calibration value. */
+ __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue);
+ }
+ else
+ {
+ /* Disable the Multi Speed oscillator (MSI). */
+ __HAL_RCC_MSI_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till MSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > MSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /*------------------------------ LSI Configuration -------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState));
+
+ /* Check the LSI State */
+ if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF)
+ {
+ /* Enable the Internal Low Speed oscillator (LSI). */
+ __HAL_RCC_LSI_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Disable the Internal Low Speed oscillator (LSI). */
+ __HAL_RCC_LSI_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ /*------------------------------ LSE Configuration -------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState));
+
+ /* Enable Power Clock*/
+ __PWR_CLK_ENABLE();
+
+ /* Enable write access to Backup domain */
+ SET_BIT(PWR->CR, PWR_CR_DBP);
+
+ /* Wait for Backup domain Write protection disable */
+ tickstart = HAL_GetTick();
+
+ while((PWR->CR & PWR_CR_DBP) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > DBP_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Reset LSEON and LSEBYP bits before configuring the LSE ----------------*/
+ __HAL_RCC_LSE_CONFIG(RCC_LSE_OFF);
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Set the new LSE configuration -----------------------------------------*/
+ __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState);
+ /* Check the LSE State */
+ if((RCC_OscInitStruct->LSEState) == RCC_LSE_ON)
+ {
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ /*-------------------------------- PLL Configuration -----------------------*/
+ /* Check the parameters */
+ assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState));
+ if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE)
+ {
+ /* Check if the PLL is used as system clock or not */
+ if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL)
+ {
+ if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource));
+ assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL));
+ assert_param(IS_RCC_PLL_DIV(RCC_OscInitStruct->PLL.PLLDIV));
+
+
+ /* Disable the main PLL. */
+ __HAL_RCC_PLL_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Configure the main PLL clock source, multiplication and division factors. */
+ __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource,
+ RCC_OscInitStruct->PLL.PLLMUL,
+ RCC_OscInitStruct->PLL.PLLDIV);
+ /* Enable the main PLL. */
+ __HAL_RCC_PLL_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Disable the main PLL. */
+ __HAL_RCC_PLL_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ else
+ {
+ return HAL_ERROR;
+ }
+ }
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the CPU, AHB and APB busses clocks according to the specified
+ * parameters in the RCC_ClkInitStruct.
+ * @param RCC_ClkInitStruct: pointer to an RCC_OscInitTypeDef structure that
+ * contains the configuration information for the RCC peripheral.
+ * @param FLatency: FLASH Latency
+ * This parameter can be one of the following values:
+ * @arg FLASH_LATENCY_0: FLASH Zero Latency cycle
+ * @arg FLASH_LATENCY_1: FLASH One Latency cycle
+ * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+ * and updated by HAL_RCC_GetHCLKFreq() function called within this function
+ *
+ * @note The MSI is used (enabled by hardware) as system clock source after
+ * startup from Reset, wake-up from STOP and STANDBY mode, or in case
+ * of failure of the HSE used directly or indirectly as system clock
+ * (if the Clock Security System CSS is enabled).
+ *
+ * @note A switch from one clock source to another occurs only if the target
+ * clock source is ready (clock stable after startup delay or PLL locked).
+ * If a clock source which is not yet ready is selected, the switch will
+ * occur when the clock source will be ready.
+ * You can use HAL_RCC_GetClockConfig() function to know which clock is
+ * currently used as system clock source.
+ * @note Depending on the device voltage range, the software has to set correctly
+ * HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency
+ * (for more details refer to section above "Initialization/de-initialization functions")
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency)
+{
+ uint32_t tickstart = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType));
+ assert_param(IS_FLASH_LATENCY(FLatency));
+
+ /* To correctly read data from FLASH memory, the number of wait states (LATENCY)
+ must be correctly programmed according to the frequency of the CPU clock
+ (HCLK) and the supply voltage of the device. */
+
+ /* Increasing the CPU frequency */
+ if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY))
+ {
+ /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+ __HAL_FLASH_SET_LATENCY(FLatency);
+
+ /* Check that the new number of wait states is taken into account to access the Flash
+ memory by reading the FLASH_ACR register */
+ if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency)
+ {
+ return HAL_ERROR;
+ }
+
+ /*-------------------------- HCLK Configuration --------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
+ {
+ assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
+ }
+
+ /*------------------------- SYSCLK Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
+ {
+ assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
+
+ /* HSE is selected as System Clock Source */
+ if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+ {
+ /* Check the HSE ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* PLL is selected as System Clock Source */
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
+ {
+ /* Check the PLL ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* HSI is selected as System Clock Source */
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
+ {
+ /* Check the HSI ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* MSI is selected as System Clock Source */
+ else
+ {
+ /* Check the MSI ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource);
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_HSE)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_HSI)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ while(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_MSI)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /* Decreasing the CPU frequency */
+ else
+ {
+ /*-------------------------- HCLK Configuration --------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
+ {
+ assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
+ }
+
+ /*------------------------- SYSCLK Configuration -------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
+ {
+ assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
+
+ /* HSE is selected as System Clock Source */
+ if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+ {
+ /* Check the HSE ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* PLL is selected as System Clock Source */
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
+ {
+ /* Check the PLL ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* HSI is selected as System Clock Source */
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
+ {
+ /* Check the HSI ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* MSI is selected as System Clock Source */
+ else
+ {
+ /* Check the MSI ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource);
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_HSE)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
+ {
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_HSI)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ while(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_MSI)
+ {
+ if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+
+ /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+ __HAL_FLASH_SET_LATENCY(FLatency);
+
+ /* Check that the new number of wait states is taken into account to access the Flash
+ memory by reading the FLASH_ACR register */
+ if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ /*-------------------------- PCLK1 Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
+ {
+ assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider);
+ }
+
+ /*-------------------------- PCLK2 Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
+ {
+ assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3));
+ }
+
+ /* Configure the source of time base considering new system clocks settings*/
+ HAL_InitTick (TICK_INT_PRIORITY);
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions
+ * @brief RCC clocks control functions
+ *
+ @verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..]
+ This subsection provides a set of functions allowing to control the RCC Clocks
+ frequencies.
+
+ @endverbatim
+ * @{
+ */
+
+/**
+ * @brief Selects the clock source to output on MCO pin.
+ * @note MCO pin should be configured in alternate function mode.
+ * @param RCC_MCOx: specifies the output direction for the clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO: Clock source to output on MCO1 pin(PA8).
+ * @param RCC_MCOSource: specifies the clock source to output.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1SOURCE_NOCLOCK: No clock selected
+ * @arg RCC_MCO1SOURCE_SYSCLK: System clock selected
+ * @arg RCC_MCO1SOURCE_HSI: HSI oscillator clock selected
+ * @arg RCC_MCO1SOURCE_MSI: MSI oscillator clock selected
+ * @arg RCC_MCO1SOURCE_HSE: HSE oscillator clock selected
+ * @arg RCC_MCO1SOURCE_PLLCLK: PLL clock selected
+ * @arg RCC_MCO1SOURCE_LSI: LSI clock selected
+ * @arg RCC_MCO1SOURCE_LSE: LSE clock selected
+ * @param RCC_MCODiv: specifies the MCO DIV.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCODIV_1: no division applied to MCO clock
+ * @arg RCC_MCODIV_2: division by 2 applied to MCO clock
+ * @arg RCC_MCODIV_4: division by 4 applied to MCO clock
+ * @arg RCC_MCODIV_8: division by 8 applied to MCO clock
+ * @arg RCC_MCODIV_16: division by 16 applied to MCO clock
+ * @retval None
+ */
+void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
+{
+ GPIO_InitTypeDef gpio;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_MCO(RCC_MCOx));
+ assert_param(IS_RCC_MCODIV(RCC_MCODiv));
+ assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
+
+ /* MCO Clock Enable */
+ __MCO1_CLK_ENABLE();
+
+ /* Configure the MCO1 pin in alternate function mode */
+ gpio.Pin = MCO1_PIN;
+ gpio.Mode = GPIO_MODE_AF_PP;
+ gpio.Speed = GPIO_SPEED_HIGH;
+ gpio.Pull = GPIO_NOPULL;
+ gpio.Alternate = GPIO_AF0_MCO;
+ HAL_GPIO_Init(MCO1_GPIO_PORT, &gpio);
+
+ /* Mask MCO and MCOPRE[2:0] bits then Select MCO clock source and prescaler */
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCOSEL | RCC_CFGR_MCOPRE), (RCC_MCOSource | RCC_MCODiv));
+}
+
+/**
+ * @brief Enables the Clock Security System.
+ * @note If a failure is detected on the HSE oscillator clock, this oscillator
+ * is automatically disabled and an interrupt is generated to inform the
+ * software about the failure (Clock Security System Interrupt, CSSI),
+ * allowing the MCU to perform rescue operations. The CSSI is linked to
+ * the Cortex-M3 NMI (Non-Maskable Interrupt) exception vector.
+ * @retval None
+ */
+void HAL_RCC_EnableCSS(void)
+{
+ *(__IO uint32_t *) CR_CSSON_BB = (uint32_t)ENABLE;
+}
+
+/**
+ * @brief Disables the Clock Security System.
+ * @retval None
+ */
+void HAL_RCC_DisableCSS(void)
+{
+ *(__IO uint32_t *) CR_CSSON_BB = (uint32_t)DISABLE;
+}
+
+/**
+ * @brief Returns the SYSCLK frequency
+ *
+ * @note The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ * @note If SYSCLK source is MSI, function returns values based on MSI
+ * Value as defined by the MSI range.
+ * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
+ * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**)
+ * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied/divided by the PLL factors.
+ * @note (*) HSI_VALUE is a constant defined in stm32l1xx_hal_conf.h file (default value
+ * 16 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ * @note (**) HSE_VALUE is a constant defined in stm32l1xx_hal_conf.h file (default value
+ * 8 MHz), user has to ensure that HSE_VALUE is same as the real
+ * frequency of the crystal used. Otherwise, this function may
+ * have wrong result.
+ *
+ * @note The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ *
+ * @note This function can be used by the user application to compute the
+ * baudrate for the communication peripherals or configure other parameters.
+ *
+ * @note Each time SYSCLK changes, this function must be called to update the
+ * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
+ *
+ *
+ * @retval SYSCLK frequency
+ */
+uint32_t HAL_RCC_GetSysClockFreq(void)
+{
+ uint32_t tmpreg = 0, pllm = 0, plld = 0, pllvco = 0, msiclkrange = 0;
+ uint32_t sysclockfreq = 0;
+
+ tmpreg = RCC->CFGR;
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ switch (tmpreg & RCC_CFGR_SWS)
+ {
+ case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */
+ {
+ sysclockfreq = HSI_VALUE;
+ break;
+ }
+ case RCC_CFGR_SWS_HSE: /* HSE used as system clock */
+ {
+ sysclockfreq = HSE_VALUE;
+ break;
+ }
+ case RCC_CFGR_SWS_PLL: /* PLL used as system clock */
+ {
+ pllm = aPLLMulFactorTable[(uint32_t)(tmpreg & RCC_CFGR_PLLMUL) >> POSITION_VAL(RCC_CFGR_PLLMUL)];
+ plld = aPLLDivisionFactorTable[(uint32_t)(tmpreg & RCC_CFGR_PLLDIV) >> POSITION_VAL(RCC_CFGR_PLLDIV)];
+ if (__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI)
+ {
+ /* HSE used as PLL clock source */
+ pllvco = HSE_VALUE * (pllm / plld);
+ }
+ else
+ {
+ /* HSI used as PLL clock source */
+ pllvco = HSI_VALUE * (pllm / plld);
+ }
+ sysclockfreq = pllvco;
+ break;
+ }
+ case RCC_CFGR_SWS_MSI: /* MSI used as system clock source */
+ default: /* MSI used as system clock */
+ {
+ msiclkrange = (RCC->ICSCR & RCC_ICSCR_MSIRANGE ) >> POSITION_VAL(RCC_ICSCR_MSIRANGE);
+ sysclockfreq = (32768 * (1 << (msiclkrange + 1)));
+ break;
+ }
+ }
+ return sysclockfreq;
+}
+
+/**
+ * @brief Returns the HCLK frequency
+ * @note Each time HCLK changes, this function must be called to update the
+ * right HCLK value. Otherwise, any configuration based on this function will be incorrect.
+ *
+ * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+ * and updated within this function
+ * @retval HCLK frequency
+ */
+uint32_t HAL_RCC_GetHCLKFreq(void)
+{
+ SystemCoreClock = HAL_RCC_GetSysClockFreq() >> aAPBAHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> POSITION_VAL(RCC_CFGR_HPRE)];
+ return SystemCoreClock;
+}
+
+/**
+ * @brief Returns the PCLK1 frequency
+ * @note Each time PCLK1 changes, this function must be called to update the
+ * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect.
+ * @retval PCLK1 frequency
+ */
+uint32_t HAL_RCC_GetPCLK1Freq(void)
+{
+ /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/
+ return (HAL_RCC_GetHCLKFreq() >> aAPBAHBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1)>> POSITION_VAL(RCC_CFGR_PPRE1)]);
+}
+
+/**
+ * @brief Returns the PCLK2 frequency
+ * @note Each time PCLK2 changes, this function must be called to update the
+ * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect.
+ * @retval PCLK2 frequency
+ */
+uint32_t HAL_RCC_GetPCLK2Freq(void)
+{
+ /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/
+ return (HAL_RCC_GetHCLKFreq()>> aAPBAHBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2)>> POSITION_VAL(RCC_CFGR_PPRE2)]);
+}
+
+/**
+ * @brief Configures the RCC_OscInitStruct according to the internal
+ * RCC configuration registers.
+ * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that
+ * will be configured.
+ * @retval None
+ */
+void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
+{
+ /* Set all possible values for the Oscillator type parameter ---------------*/
+ RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI \
+ | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_MSI;
+
+ /* Get the HSE configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP)
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS;
+ }
+ else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON)
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_OFF;
+ }
+
+ /* Get the HSI configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION)
+ {
+ RCC_OscInitStruct->HSIState = RCC_HSI_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->HSIState = RCC_HSI_OFF;
+ }
+
+ RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->ICSCR & RCC_ICSCR_HSITRIM) >> POSITION_VAL(RCC_ICSCR_HSITRIM));
+
+ /* Get the MSI configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_MSION) == RCC_CR_MSION)
+ {
+ RCC_OscInitStruct->MSIState = RCC_MSI_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->MSIState = RCC_MSI_OFF;
+ }
+
+ RCC_OscInitStruct->MSICalibrationValue = (uint32_t)((RCC->ICSCR & RCC_ICSCR_MSITRIM) >> POSITION_VAL(RCC_ICSCR_MSITRIM));
+ RCC_OscInitStruct->MSIClockRange = (uint32_t)((RCC->ICSCR & RCC_ICSCR_MSIRANGE));
+
+ /* Get the LSE configuration -----------------------------------------------*/
+ if((RCC->CSR &RCC_CSR_LSEBYP) == RCC_CSR_LSEBYP)
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS;
+ }
+ else if((RCC->CSR &RCC_CSR_LSEON) == RCC_CSR_LSEON)
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_OFF;
+ }
+
+ /* Get the LSI configuration -----------------------------------------------*/
+ if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION)
+ {
+ RCC_OscInitStruct->LSIState = RCC_LSI_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->LSIState = RCC_LSI_OFF;
+ }
+
+ /* Get the PLL configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON)
+ {
+ RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF;
+ }
+ RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC);
+ RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMUL);
+ RCC_OscInitStruct->PLL.PLLDIV = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLDIV);
+}
+
+/**
+ * @brief Configures the RCC_ClkInitStruct according to the internal
+ * RCC configuration registers.
+ * @param RCC_ClkInitStruct: pointer to an RCC_ClkInitTypeDef structure that
+ * will be configured.
+ * @param pFLatency: Pointer on the Flash Latency.
+ * @retval None
+ */
+void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency)
+{
+ /* Set all possible values for the Clock type parameter --------------------*/
+ RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+
+ /* Get the SYSCLK configuration --------------------------------------------*/
+ RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW);
+
+ /* Get the HCLK configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE);
+
+ /* Get the APB1 configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1);
+
+ /* Get the APB2 configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3);
+
+ /* Get the Flash Wait State (Latency) configuration ------------------------*/
+ *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY);
+}
+
+/**
+ * @brief This function handles the RCC CSS interrupt request.
+ * @note This API should be called under the NMI_Handler().
+ * @retval None
+ */
+void HAL_RCC_NMI_IRQHandler(void)
+{
+ /* Check RCC CSSF flag */
+ if(__HAL_RCC_GET_IT(RCC_IT_CSS))
+ {
+ /* RCC Clock Security System interrupt user callback */
+ HAL_RCC_CCSCallback();
+
+ /* Clear RCC CSS pending bit */
+ __HAL_RCC_CLEAR_IT(RCC_IT_CSS);
+ }
+}
+
+/**
+ * @brief RCC Clock Security System interrupt callback
+ * @retval none
+ */
+__weak void HAL_RCC_CCSCallback(void)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_RCC_CCSCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* HAL_RCC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
