Stuart Northfield
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_hal_tim.c
- Revision:
- 394:83f921546702
- Parent:
- 393:17d2d502961d
- Child:
- 395:bfce16e86ea4
--- a/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_hal_tim.c Fri Nov 07 12:00:11 2014 +0000
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,5039 +0,0 @@
-/**
- ******************************************************************************
- * @file stm32l1xx_hal_tim.c
- * @author MCD Application Team
- * @version V1.0.0
- * @date 5-September-2014
- * @brief TIM HAL module driver.
- * This file provides firmware functions to manage the following
- * functionalities of the Timer (TIM) peripheral:
- * + Time Base Initialization
- * + Time Base Start
- * + Time Base Start Interruption
- * + Time Base Start DMA
- * + Time Output Compare/PWM Initialization
- * + Time Output Compare/PWM Channel Configuration
- * + Time Output Compare/PWM Start
- * + Time Output Compare/PWM Start Interruption
- * + Time Output Compare/PWM Start DMA
- * + Time Input Capture Initialization
- * + Time Input Capture Channel Configuration
- * + Time Input Capture Start
- * + Time Input Capture Start Interruption
- * + Time Input Capture Start DMA
- * + Time One Pulse Initialization
- * + Time One Pulse Channel Configuration
- * + Time One Pulse Start
- * + Time Encoder Interface Initialization
- * + Time Encoder Interface Start
- * + Time Encoder Interface Start Interruption
- * + Time Encoder Interface Start DMA
- * + Commutation Event configuration with Interruption and DMA
- * + Time OCRef clear configuration
- * + Time External Clock configuration
- * + Time Master and Slave synchronization configuration
- @verbatim
- ==============================================================================
- ##### TIMER Generic features #####
- ==============================================================================
- [..] The Timer features include:
- (#) 16-bit up, down, up/down auto-reload counter.
- (#) 16-bit programmable prescaler allowing dividing (also on the fly) the
- counter clock frequency either by any factor between 1 and 65536.
- (#) Up to 4 independent channels for:
- (++) Input Capture
- (++) Output Compare
- (++) PWM generation (Edge and Center-aligned Mode)
- (++) One-pulse mode output
- (#) Synchronization circuit to control the timer with external signals and to interconnect
- several timers together.
- (#) Supports incremental (quadrature) encoder
-
- ##### How to use this driver #####
-================================================================================
- [..]
- (#) Initialize the TIM low level resources by implementing the following functions
- depending from feature used :
- (++) Time Base : HAL_TIM_Base_MspInit()
- (++) Input Capture : HAL_TIM_IC_MspInit()
- (++) Output Compare : HAL_TIM_OC_MspInit()
- (++) PWM generation : HAL_TIM_PWM_MspInit()
- (++) One-pulse mode output : HAL_TIM_OnePulse_MspInit()
- (++) Encoder mode output : HAL_TIM_Encoder_MspInit()
-
- (#) Initialize the TIM low level resources :
- (##) Enable the TIM interface clock using __TIMx_CLK_ENABLE();
- (##) TIM pins configuration
- (+++) Enable the clock for the TIM GPIOs using the following function:
- __GPIOx_CLK_ENABLE();
- (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init();
-
- (#) The external Clock can be configured, if needed (the default clock is the
- internal clock from the APBx), using the following function:
- HAL_TIM_ConfigClockSource, the clock configuration should be done before
- any start function.
-
- (#) Configure the TIM in the desired functioning mode using one of the
- Initialization function of this driver:
- (++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base
- (++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an
- Output Compare signal.
- (++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a
- PWM signal.
- (++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an
- external signal.
- (++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer
- in One Pulse Mode.
- (++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface.
-
- (#) Activate the TIM peripheral using one of the start functions depending from the feature used:
- (++) Time Base : HAL_TIM_Base_Start(), HAL_TIM_Base_Start_DMA(), HAL_TIM_Base_Start_IT()
- (++) Input Capture : HAL_TIM_IC_Start(), HAL_TIM_IC_Start_DMA(), HAL_TIM_IC_Start_IT()
- (++) Output Compare : HAL_TIM_OC_Start(), HAL_TIM_OC_Start_DMA(), HAL_TIM_OC_Start_IT()
- (++) PWM generation : HAL_TIM_PWM_Start(), HAL_TIM_PWM_Start_DMA(), HAL_TIM_PWM_Start_IT()
- (++) One-pulse mode output : HAL_TIM_OnePulse_Start(), HAL_TIM_OnePulse_Start_IT()
- (++) Encoder mode output : HAL_TIM_Encoder_Start(), HAL_TIM_Encoder_Start_DMA(), HAL_TIM_Encoder_Start_IT().
-
- (#) The DMA Burst is managed with the two following functions:
- HAL_TIM_DMABurst_WriteStart()
- HAL_TIM_DMABurst_ReadStart()
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32l1xx_hal.h"
-
-/** @addtogroup STM32L1xx_HAL_Driver
- * @{
- */
-
-/** @defgroup TIM TIM
- * @brief TIM HAL module driver
- * @{
- */
-
-#ifdef HAL_TIM_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-/* Private macro -------------------------------------------------------------*/
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/** @defgroup TIM_Private_Functions TIM Private Functions
- * @{
- */
-static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
-static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
-static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
-
-static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter);
-static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter);
-static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter);
-static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter);
-static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter);
-
-static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler,
- uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter);
-
-static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t InputTriggerSource);
-static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma);
-static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma);
-static void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure);
-static void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter);
-static void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
-static void TIM_DMADelayPulseCplt(DMA_HandleTypeDef *hdma);
-static void TIM_DMAError(DMA_HandleTypeDef *hdma);
-static void TIM_DMACaptureCplt(DMA_HandleTypeDef *hdma);
-static void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState);
-
-/**
- * @}
- */
-
-/* External functions ---------------------------------------------------------*/
-
-/** @defgroup TIM_Exported_Functions TIM Exported Functions
- * @{
- */
-
-/** @defgroup TIM_Exported_Functions_Group1 Time Base functions
- * @brief Time Base functions
- *
-@verbatim
- ==============================================================================
- ##### Time Base functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM base.
- (+) De-initialize the TIM base.
- (+) Start the Time Base.
- (+) Stop the Time Base.
- (+) Start the Time Base and enable interrupt.
- (+) Stop the Time Base and disable interrupt.
- (+) Start the Time Base and enable DMA transfer.
- (+) Stop the Time Base and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM Time base Unit according to the specified
- * parameters in the TIM_HandleTypeDef and create the associated handle.
- * @param htim: TIM Base handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef *htim)
-{
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
- assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC */
- HAL_TIM_Base_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Set the Time Base configuration */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the TIM Base peripheral
- * @param htim: TIM Base handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- HAL_TIM_Base_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM Base MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_Base_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_Base_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM Base MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_Base_MspDeInit could be implemented in the user file
- */
-}
-
-
-/**
- * @brief Starts the TIM Base generation.
- * @param htim : TIM handle
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Change the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Base generation.
- * @param htim : TIM handle
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Base generation in interrupt mode.
- * @param htim : TIM handle
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- /* Enable the TIM Update interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_UPDATE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Base generation in interrupt mode.
- * @param htim : TIM handle
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- /* Disable the TIM Update interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_UPDATE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Base generation in DMA mode.
- * @param htim : TIM handle
- * @param pData: The source Buffer address.
- * @param Length: The length of data to be transferred from memory to peripheral.
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_INSTANCE(htim->Instance));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if((pData == 0 ) && (Length > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length);
-
- /* Enable the TIM Update DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_UPDATE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Base generation in DMA mode.
- * @param htim : TIM handle
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_INSTANCE(htim->Instance));
-
- /* Disable the TIM Update DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_UPDATE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group2 Time Output Compare functions
- * @brief Time Output Compare functions
- *
-@verbatim
- ==============================================================================
- ##### Time Output Compare functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM Output Compare.
- (+) De-initialize the TIM Output Compare.
- (+) Start the Time Output Compare.
- (+) Stop the Time Output Compare.
- (+) Start the Time Output Compare and enable interrupt.
- (+) Stop the Time Output Compare and disable interrupt.
- (+) Start the Time Output Compare and enable DMA transfer.
- (+) Stop the Time Output Compare and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM Output Compare according to the specified
- * parameters in the TIM_HandleTypeDef and create the associated handle.
- * @param htim: TIM Output Compare handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim)
-{
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
- assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_OC_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Init the base time for the Output Compare */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the TIM peripheral
- * @param htim: TIM Output Compare handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_OC_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM Output Compare MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_OC_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_OC_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM Output Compare MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_OC_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Starts the TIM Output Compare signal generation.
- * @param htim : TIM Output Compare handle
- * @param Channel : TIM Channel to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Enable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Output Compare signal generation.
- * @param htim : TIM handle
- * @param Channel : TIM Channel to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Disable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Output Compare signal generation in interrupt mode.
- * @param htim : TIM OC handle
- * @param Channel : TIM Channel to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Enable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Enable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Enable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Enable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Enable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Output Compare signal generation in interrupt mode.
- * @param htim : TIM Output Compare handle
- * @param Channel : TIM Channel to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Output Compare signal generation in DMA mode.
- * @param htim : TIM Output Compare handle
- * @param Channel : TIM Channel to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @param pData: The source Buffer address.
- * @param Length: The length of data to be transferred from memory to TIM peripheral
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if(((uint32_t)pData == 0 ) && (Length > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
-
- /* Enable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
-
- /* Enable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
-
- /* Enable the TIM Capture/Compare 3 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
-
- /* Enable the TIM Capture/Compare 4 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Enable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Output Compare signal generation in DMA mode.
- * @param htim : TIM Output Compare handle
- * @param Channel : TIM Channel to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Output compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group3 Time PWM functions
- * @brief Time PWM functions
- *
-@verbatim
- ==============================================================================
- ##### Time PWM functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM OPWM.
- (+) De-initialize the TIM PWM.
- (+) Start the Time PWM.
- (+) Stop the Time PWM.
- (+) Start the Time PWM and enable interrupt.
- (+) Stop the Time PWM and disable interrupt.
- (+) Start the Time PWM and enable DMA transfer.
- (+) Stop the Time PWM and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM PWM Time Base according to the specified
- * parameters in the TIM_HandleTypeDef and create the associated handle.
- * @param htim: TIM handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef *htim)
-{
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
- assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_PWM_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Init the base time for the PWM */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the TIM peripheral
- * @param htim: TIM handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_PWM_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM PWM MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_PWM_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM PWM MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_PWM_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Starts the PWM signal generation.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the PWM signal generation.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Disable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the PWM signal generation in interrupt mode.
- * @param htim : TIM handle
- * @param Channel : TIM Channel to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Enable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Enable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Enable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Enable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the PWM signal generation in interrupt mode.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM PWM signal generation in DMA mode.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @param pData: The source Buffer address.
- * @param Length: The length of data to be transferred from memory to TIM peripheral
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if(((uint32_t)pData == 0 ) && (Length > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
-
- /* Enable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
-
- /* Enable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
-
- /* Enable the TIM Output Capture/Compare 3 request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
-
- /* Enable the TIM Capture/Compare 4 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM PWM signal generation in DMA mode.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group4 Time Input Capture functions
- * @brief Time Input Capture functions
- *
-@verbatim
- ==============================================================================
- ##### Time Input Capture functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM Input Capture.
- (+) De-initialize the TIM Input Capture.
- (+) Start the Time Input Capture.
- (+) Stop the Time Input Capture.
- (+) Start the Time Input Capture and enable interrupt.
- (+) Stop the Time Input Capture and disable interrupt.
- (+) Start the Time Input Capture and enable DMA transfer.
- (+) Stop the Time Input Capture and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM Input Capture Time base according to the specified
- * parameters in the TIM_HandleTypeDef and create the associated handle.
- * @param htim: TIM Input Capture handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef *htim)
-{
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
- assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_IC_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Init the base time for the input capture */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the TIM peripheral
- * @param htim: TIM Input Capture handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_IC_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM INput Capture MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_IC_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_IC_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM Input Capture MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_IC_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Starts the TIM Input Capture measurement.
- * @param htim : TIM Input Capture handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Start (TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Enable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Input Capture measurement.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- /* Disable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Input Capture measurement in interrupt mode.
- * @param htim : TIM Input Capture handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Enable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Enable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Enable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Enable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
- /* Enable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Input Capture measurement in interrupt mode.
- * @param htim : TIM handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Input Capture measurement on in DMA mode.
- * @param htim : TIM Input Capture handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @param pData: The destination Buffer address.
- * @param Length: The length of data to be transferred from TIM peripheral to memory.
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
- assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if((pData == 0 ) && (Length > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length);
-
- /* Enable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length);
-
- /* Enable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length);
-
- /* Enable the TIM Capture/Compare 3 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length);
-
- /* Enable the TIM Capture/Compare 4 DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Enable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Input Capture measurement on in DMA mode.
- * @param htim : TIM Input Capture handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
- assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Disable the TIM Capture/Compare 1 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Disable the TIM Capture/Compare 2 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- /* Disable the TIM Capture/Compare 3 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- /* Disable the TIM Capture/Compare 4 DMA request */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
- }
- break;
-
- default:
- break;
- }
-
- /* Disable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group5 Time One Pulse functions
- * @brief Time One Pulse functions
- *
-@verbatim
- ==============================================================================
- ##### Time One Pulse functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM One Pulse.
- (+) De-initialize the TIM One Pulse.
- (+) Start the Time One Pulse.
- (+) Stop the Time One Pulse.
- (+) Start the Time One Pulse and enable interrupt.
- (+) Stop the Time One Pulse and disable interrupt.
- (+) Start the Time One Pulse and enable DMA transfer.
- (+) Stop the Time One Pulse and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM One Pulse Time Base according to the specified
- * parameters in the TIM_HandleTypeDef and create the associated handle.
- * @param htim: TIM OnePulse handle
- * @param OnePulseMode: Select the One pulse mode.
- * This parameter can be one of the following values:
- * @arg TIM_OPMODE_SINGLE: Only one pulse will be generated.
- * @arg TIM_OPMODE_REPETITIVE: Repetitive pulses wil be generated.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef *htim, uint32_t OnePulseMode)
-{
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
- assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
- assert_param(IS_TIM_OPM_MODE(OnePulseMode));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_OnePulse_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Configure the Time base in the One Pulse Mode */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Reset the OPM Bit */
- htim->Instance->CR1 &= ~TIM_CR1_OPM;
-
- /* Configure the OPM Mode */
- htim->Instance->CR1 |= OnePulseMode;
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitializes the TIM One Pulse
- * @param htim: TIM One Pulse handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- HAL_TIM_OnePulse_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM One Pulse MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_OnePulse_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM One Pulse MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_OnePulse_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Starts the TIM One Pulse signal generation.
- * @param htim : TIM One Pulse handle
- * @param OutputChannel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
-{
- /* Enable the Capture compare and the Input Capture channels
- (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
- if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
- if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
-
- No need to enable the counter, it's enabled automatically by hardware
- (the counter starts in response to a stimulus and generate a pulse */
-
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM One Pulse signal generation.
- * @param htim : TIM One Pulse handle
- * @param OutputChannel : TIM Channels to be disable
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
-{
- /* Disable the Capture compare and the Input Capture channels
- (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
- if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
- if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
-
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM One Pulse signal generation in interrupt mode.
- * @param htim : TIM One Pulse handle
- * @param OutputChannel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
-{
- /* Enable the Capture compare and the Input Capture channels
- (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
- if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
- if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
-
- No need to enable the counter, it's enabled automatically by hardware
- (the counter starts in response to a stimulus and generate a pulse */
-
- /* Enable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
-
- /* Enable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
-
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM One Pulse signal generation in interrupt mode.
- * @param htim : TIM One Pulse handle
- * @param OutputChannel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
-{
- /* Disable the TIM Capture/Compare 1 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
-
- /* Disable the TIM Capture/Compare 2 interrupt */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
-
- /* Disable the Capture compare and the Input Capture channels
- (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
- if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
- if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group6 Time Encoder functions
- * @brief Time Encoder functions
- *
-@verbatim
- ==============================================================================
- ##### Time Encoder functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Initialize and configure the TIM Encoder.
- (+) De-initialize the TIM Encoder.
- (+) Start the Time Encoder.
- (+) Stop the Time Encoder.
- (+) Start the Time Encoder and enable interrupt.
- (+) Stop the Time Encoder and disable interrupt.
- (+) Start the Time Encoder and enable DMA transfer.
- (+) Stop the Time Encoder and disable DMA transfer.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Initializes the TIM Encoder Interface and create the associated handle.
- * @param htim: TIM Encoder Interface handle
- * @param sConfig: TIM Encoder Interface configuration structure
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef *htim, TIM_Encoder_InitTypeDef* sConfig)
-{
- uint32_t tmpsmcr = 0;
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Check the TIM handle allocation */
- if(htim == HAL_NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- assert_param(IS_TIM_ENCODER_MODE(sConfig->EncoderMode));
- assert_param(IS_TIM_IC_SELECTION(sConfig->IC1Selection));
- assert_param(IS_TIM_IC_SELECTION(sConfig->IC2Selection));
- assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity));
- assert_param(IS_TIM_IC_POLARITY(sConfig->IC2Polarity));
- assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler));
- assert_param(IS_TIM_IC_PRESCALER(sConfig->IC2Prescaler));
- assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter));
- assert_param(IS_TIM_IC_FILTER(sConfig->IC2Filter));
-
- if(htim->State == HAL_TIM_STATE_RESET)
- {
- /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
- HAL_TIM_Encoder_MspInit(htim);
- }
-
- /* Set the TIM state */
- htim->State= HAL_TIM_STATE_BUSY;
-
- /* Reset the SMS bits */
- htim->Instance->SMCR &= ~TIM_SMCR_SMS;
-
- /* Configure the Time base in the Encoder Mode */
- TIM_Base_SetConfig(htim->Instance, &htim->Init);
-
- /* Get the TIMx SMCR register value */
- tmpsmcr = htim->Instance->SMCR;
-
- /* Get the TIMx CCMR1 register value */
- tmpccmr1 = htim->Instance->CCMR1;
-
- /* Get the TIMx CCER register value */
- tmpccer = htim->Instance->CCER;
-
- /* Set the encoder Mode */
- tmpsmcr |= sConfig->EncoderMode;
-
- /* Select the Capture Compare 1 and the Capture Compare 2 as input */
- tmpccmr1 &= ~(TIM_CCMR1_CC1S | TIM_CCMR1_CC2S);
- tmpccmr1 |= (sConfig->IC1Selection | (sConfig->IC2Selection << 8));
-
- /* Set the the Capture Compare 1 and the Capture Compare 2 prescalers and filters */
- tmpccmr1 &= ~(TIM_CCMR1_IC1PSC | TIM_CCMR1_IC2PSC);
- tmpccmr1 &= (~(TIM_CCMR1_IC1F | TIM_CCMR1_IC2F));
- tmpccmr1 |= sConfig->IC1Prescaler | (sConfig->IC2Prescaler << 8);
- tmpccmr1 |= (sConfig->IC1Filter << 4) | (sConfig->IC2Filter << 12);
-
- /* Set the TI1 and the TI2 Polarities */
- tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC2P);
- tmpccer &= ~(TIM_CCER_CC1NP | TIM_CCER_CC2NP);
- tmpccer |= sConfig->IC1Polarity | (sConfig->IC2Polarity << 4);
-
- /* Write to TIMx SMCR */
- htim->Instance->SMCR = tmpsmcr;
-
- /* Write to TIMx CCMR1 */
- htim->Instance->CCMR1 = tmpccmr1;
-
- /* Write to TIMx CCER */
- htim->Instance->CCER = tmpccer;
-
- /* Initialize the TIM state*/
- htim->State= HAL_TIM_STATE_READY;
-
- return HAL_OK;
-}
-
-
-/**
- * @brief DeInitializes the TIM Encoder interface
- * @param htim: TIM Encoder handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef *htim)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Disable the TIM Peripheral Clock */
- __HAL_TIM_DISABLE(htim);
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- HAL_TIM_Encoder_MspDeInit(htim);
-
- /* Change TIM state */
- htim->State = HAL_TIM_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM Encoder Interface MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_Encoder_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitializes TIM Encoder Interface MSP.
- * @param htim: TIM handle
- * @retval None
- */
-__weak void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_Encoder_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Starts the TIM Encoder Interface.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- /* Enable the encoder interface channels */
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- break;
- }
- case TIM_CHANNEL_2:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
- break;
- }
- default :
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
- break;
- }
- }
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Encoder Interface.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- /* Disable the Input Capture channels 1 and 2
- (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- break;
- }
- case TIM_CHANNEL_2:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
- break;
- }
- default :
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
- break;
- }
- }
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Encoder Interface in interrupt mode.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- /* Enable the encoder interface channels */
- /* Enable the capture compare Interrupts 1 and/or 2 */
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
- break;
- }
- case TIM_CHANNEL_2:
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
- break;
- }
- default :
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
- __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
- break;
- }
- }
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Encoder Interface in interrupt mode.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be disabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- /* Disable the Input Capture channels 1 and 2
- (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
- if(Channel == TIM_CHANNEL_1)
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
-
- /* Disable the capture compare Interrupts 1 */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
- }
- else if(Channel == TIM_CHANNEL_2)
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the capture compare Interrupts 2 */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
- }
- else
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the capture compare Interrupts 1 and 2 */
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
- __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
- }
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Starts the TIM Encoder Interface in DMA mode.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @param pData1: The destination Buffer address for IC1.
- * @param pData2: The destination Buffer address for IC2.
- * @param Length: The length of data to be transferred from TIM peripheral to memory.
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData1, uint32_t *pData2, uint16_t Length)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if((((pData1 == 0) || (pData2 == 0) )) && (Length > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t )pData1, Length);
-
- /* Enable the TIM Input Capture DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError;
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length);
-
- /* Enable the TIM Input Capture DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
- }
- break;
-
- case TIM_CHANNEL_ALL:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length);
-
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length);
-
- /* Enable the Peripheral */
- __HAL_TIM_ENABLE(htim);
-
- /* Enable the Capture compare channel */
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
-
- /* Enable the TIM Input Capture DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
- /* Enable the TIM Input Capture DMA request */
- __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
- }
- break;
-
- default:
- break;
- }
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM Encoder Interface in DMA mode.
- * @param htim : TIM Encoder Interface handle
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
-*/
-HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
-
- /* Disable the Input Capture channels 1 and 2
- (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
- if(Channel == TIM_CHANNEL_1)
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
-
- /* Disable the capture compare DMA Request 1 */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
- }
- else if(Channel == TIM_CHANNEL_2)
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the capture compare DMA Request 2 */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
- }
- else
- {
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
- TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
-
- /* Disable the capture compare DMA Request 1 and 2 */
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
- __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
- }
-
- /* Disable the Peripheral */
- __HAL_TIM_DISABLE(htim);
-
- /* Change the htim state */
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @}
- */
-/** @defgroup TIM_Exported_Functions_Group7 TIM IRQ handler management
- * @brief IRQ handler management
- *
-@verbatim
- ==============================================================================
- ##### IRQ handler management #####
- ==============================================================================
- [..]
- This section provides Timer IRQ handler function.
-
-@endverbatim
- * @{
- */
-/**
- * @brief This function handles TIM interrupts requests.
- * @param htim: TIM handle
- * @retval None
- */
-void HAL_TIM_IRQHandler(TIM_HandleTypeDef *htim)
-{
- /* Capture compare 1 event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC1) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_CC1) !=RESET)
- {
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC1);
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
-
- /* Input capture event */
- if((htim->Instance->CCMR1 & TIM_CCMR1_CC1S) != 0x00)
- {
- HAL_TIM_IC_CaptureCallback(htim);
- }
- /* Output compare event */
- else
- {
- HAL_TIM_OC_DelayElapsedCallback(htim);
- HAL_TIM_PWM_PulseFinishedCallback(htim);
- }
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
- }
- }
- }
- /* Capture compare 2 event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC2) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_CC2) !=RESET)
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC2);
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
- /* Input capture event */
- if((htim->Instance->CCMR1 & TIM_CCMR1_CC2S) != 0x00)
- {
- HAL_TIM_IC_CaptureCallback(htim);
- }
- /* Output compare event */
- else
- {
- HAL_TIM_OC_DelayElapsedCallback(htim);
- HAL_TIM_PWM_PulseFinishedCallback(htim);
- }
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
- }
- }
- /* Capture compare 3 event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC3) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_CC3) !=RESET)
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC3);
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
- /* Input capture event */
- if((htim->Instance->CCMR2 & TIM_CCMR2_CC3S) != 0x00)
- {
- HAL_TIM_IC_CaptureCallback(htim);
- }
- /* Output compare event */
- else
- {
- HAL_TIM_OC_DelayElapsedCallback(htim);
- HAL_TIM_PWM_PulseFinishedCallback(htim);
- }
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
- }
- }
- /* Capture compare 4 event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC4) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_CC4) !=RESET)
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC4);
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
- /* Input capture event */
- if((htim->Instance->CCMR2 & TIM_CCMR2_CC4S) != 0x00)
- {
- HAL_TIM_IC_CaptureCallback(htim);
- }
- /* Output compare event */
- else
- {
- HAL_TIM_OC_DelayElapsedCallback(htim);
- HAL_TIM_PWM_PulseFinishedCallback(htim);
- }
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
- }
- }
- /* TIM Update event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_UPDATE) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_UPDATE) !=RESET)
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_UPDATE);
- HAL_TIM_PeriodElapsedCallback(htim);
- }
- }
- /* TIM Trigger detection event */
- if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_TRIGGER) != RESET)
- {
- if(__HAL_TIM_GET_ITSTATUS(htim, TIM_IT_TRIGGER) !=RESET)
- {
- __HAL_TIM_CLEAR_IT(htim, TIM_IT_TRIGGER);
- HAL_TIM_TriggerCallback(htim);
- }
- }
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group8 Peripheral Control functions
- * @brief Peripheral Control functions
- *
-@verbatim
- ==============================================================================
- ##### Peripheral Control functions #####
- ==============================================================================
- [..]
- This section provides functions allowing to:
- (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode.
- (+) Configure External Clock source.
- (+) Configure Complementary channels, break features and dead time.
- (+) Configure Master and the Slave synchronization.
- (+) Configure the DMA Burst Mode.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Initializes the TIM Output Compare Channels according to the specified
- * parameters in the TIM_OC_InitTypeDef.
- * @param htim: TIM Output Compare handle
- * @param sConfig: TIM Output Compare configuration structure
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CHANNELS(Channel));
- assert_param(IS_TIM_OC_MODE(sConfig->OCMode));
- assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity));
- assert_param(IS_TIM_FAST_STATE(sConfig->OCFastMode));
-
- /* Check input state */
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
- /* Configure the TIM Channel 1 in Output Compare */
- TIM_OC1_SetConfig(htim->Instance, sConfig);
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- /* Configure the TIM Channel 2 in Output Compare */
- TIM_OC2_SetConfig(htim->Instance, sConfig);
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
- /* Configure the TIM Channel 3 in Output Compare */
- TIM_OC3_SetConfig(htim->Instance, sConfig);
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
- /* Configure the TIM Channel 4 in Output Compare */
- TIM_OC4_SetConfig(htim->Instance, sConfig);
- }
- break;
-
- default:
- break;
- }
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM Input Capture Channels according to the specified
- * parameters in the TIM_IC_InitTypeDef.
- * @param htim: TIM IC handle
- * @param sConfig: TIM Input Capture configuration structure
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
- assert_param(IS_TIM_IC_POLARITY(sConfig->ICPolarity));
- assert_param(IS_TIM_IC_SELECTION(sConfig->ICSelection));
- assert_param(IS_TIM_IC_PRESCALER(sConfig->ICPrescaler));
- assert_param(IS_TIM_IC_FILTER(sConfig->ICFilter));
-
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- if (Channel == TIM_CHANNEL_1)
- {
- /* TI1 Configuration */
- TIM_TI1_SetConfig(htim->Instance,
- sConfig->ICPolarity,
- sConfig->ICSelection,
- sConfig->ICFilter);
-
- /* Reset the IC1PSC Bits */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
-
- /* Set the IC1PSC value */
- htim->Instance->CCMR1 |= sConfig->ICPrescaler;
- }
- else if (Channel == TIM_CHANNEL_2)
- {
- /* TI2 Configuration */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- TIM_TI2_SetConfig(htim->Instance,
- sConfig->ICPolarity,
- sConfig->ICSelection,
- sConfig->ICFilter);
-
- /* Reset the IC2PSC Bits */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC;
-
- /* Set the IC2PSC value */
- htim->Instance->CCMR1 |= (sConfig->ICPrescaler << 8);
- }
- else if (Channel == TIM_CHANNEL_3)
- {
- /* TI3 Configuration */
- assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
-
- TIM_TI3_SetConfig(htim->Instance,
- sConfig->ICPolarity,
- sConfig->ICSelection,
- sConfig->ICFilter);
-
- /* Reset the IC3PSC Bits */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC;
-
- /* Set the IC3PSC value */
- htim->Instance->CCMR2 |= sConfig->ICPrescaler;
- }
- else
- {
- /* TI4 Configuration */
- assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
-
- TIM_TI4_SetConfig(htim->Instance,
- sConfig->ICPolarity,
- sConfig->ICSelection,
- sConfig->ICFilter);
-
- /* Reset the IC4PSC Bits */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC;
-
- /* Set the IC4PSC value */
- htim->Instance->CCMR2 |= (sConfig->ICPrescaler << 8);
- }
-
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM PWM channels according to the specified
- * parameters in the TIM_OC_InitTypeDef.
- * @param htim: TIM handle
- * @param sConfig: TIM PWM configuration structure
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel)
-{
- /* Check the parameters */
- assert_param(IS_TIM_CHANNELS(Channel));
- assert_param(IS_TIM_PWM_MODE(sConfig->OCMode));
- assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity));
-
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
- /* Configure the Channel 1 in PWM mode */
- TIM_OC1_SetConfig(htim->Instance, sConfig);
-
- /* Set the Preload enable bit for channel1 */
- htim->Instance->CCMR1 |= TIM_CCMR1_OC1PE;
-
- /* Configure the Output Fast mode */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE;
- htim->Instance->CCMR1 |= sConfig->OCFastMode;
- }
- break;
-
- case TIM_CHANNEL_2:
- {
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- /* Configure the Channel 2 in PWM mode */
- TIM_OC2_SetConfig(htim->Instance, sConfig);
-
- /* Set the Preload enable bit for channel2 */
- htim->Instance->CCMR1 |= TIM_CCMR1_OC2PE;
-
- /* Configure the Output Fast mode */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE;
- htim->Instance->CCMR1 |= sConfig->OCFastMode << 8;
- }
- break;
-
- case TIM_CHANNEL_3:
- {
- assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
- /* Configure the Channel 3 in PWM mode */
- TIM_OC3_SetConfig(htim->Instance, sConfig);
-
- /* Set the Preload enable bit for channel3 */
- htim->Instance->CCMR2 |= TIM_CCMR2_OC3PE;
-
- /* Configure the Output Fast mode */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE;
- htim->Instance->CCMR2 |= sConfig->OCFastMode;
- }
- break;
-
- case TIM_CHANNEL_4:
- {
- assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
- /* Configure the Channel 4 in PWM mode */
- TIM_OC4_SetConfig(htim->Instance, sConfig);
-
- /* Set the Preload enable bit for channel4 */
- htim->Instance->CCMR2 |= TIM_CCMR2_OC4PE;
-
- /* Configure the Output Fast mode */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE;
- htim->Instance->CCMR2 |= sConfig->OCFastMode << 8;
- }
- break;
-
- default:
- break;
- }
-
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initializes the TIM One Pulse Channels according to the specified
- * parameters in the TIM_OnePulse_InitTypeDef.
- * @param htim: TIM One Pulse handle
- * @param sConfig: TIM One Pulse configuration structure
- * @param OutputChannel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @param InputChannel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel)
-{
- TIM_OC_InitTypeDef temp1;
-
- /* Check the parameters */
- assert_param(IS_TIM_OPM_CHANNELS(OutputChannel));
- assert_param(IS_TIM_OPM_CHANNELS(InputChannel));
-
- if(OutputChannel != InputChannel)
- {
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Extract the Ouput compare configuration from sConfig structure */
- temp1.OCMode = sConfig->OCMode;
- temp1.Pulse = sConfig->Pulse;
- temp1.OCPolarity = sConfig->OCPolarity;
- temp1.OCIdleState = sConfig->OCIdleState;
-
- switch (OutputChannel)
- {
- case TIM_CHANNEL_1:
- {
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
-
- TIM_OC1_SetConfig(htim->Instance, &temp1);
- }
- break;
- case TIM_CHANNEL_2:
- {
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- TIM_OC2_SetConfig(htim->Instance, &temp1);
- }
- break;
- default:
- break;
- }
- switch (InputChannel)
- {
- case TIM_CHANNEL_1:
- {
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
-
- TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity,
- sConfig->ICSelection, sConfig->ICFilter);
-
- /* Reset the IC1PSC Bits */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
-
- /* Select the Trigger source */
- htim->Instance->SMCR &= ~TIM_SMCR_TS;
- htim->Instance->SMCR |= TIM_TS_TI1FP1;
-
- /* Select the Slave Mode */
- htim->Instance->SMCR &= ~TIM_SMCR_SMS;
- htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER;
- }
- break;
- case TIM_CHANNEL_2:
- {
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity,
- sConfig->ICSelection, sConfig->ICFilter);
-
- /* Reset the IC2PSC Bits */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC;
-
- /* Select the Trigger source */
- htim->Instance->SMCR &= ~TIM_SMCR_TS;
- htim->Instance->SMCR |= TIM_TS_TI2FP2;
-
- /* Select the Slave Mode */
- htim->Instance->SMCR &= ~TIM_SMCR_SMS;
- htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER;
- }
- break;
-
- default:
- break;
- }
-
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
- else
- {
- return HAL_ERROR;
- }
-}
-
-/**
- * @brief Configure the DMA Burst to transfer Data from the memory to the TIM peripheral
- * @param htim: TIM handle
- * @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data write
- * This parameters can be on of the following values:
- * @arg TIM_DMABase_CR1
- * @arg TIM_DMABase_CR2
- * @arg TIM_DMABase_SMCR
- * @arg TIM_DMABase_DIER
- * @arg TIM_DMABase_SR
- * @arg TIM_DMABase_EGR
- * @arg TIM_DMABase_CCMR1
- * @arg TIM_DMABase_CCMR2
- * @arg TIM_DMABase_CCER
- * @arg TIM_DMABase_CNT
- * @arg TIM_DMABase_PSC
- * @arg TIM_DMABase_ARR
- * @arg TIM_DMABase_CCR1
- * @arg TIM_DMABase_CCR2
- * @arg TIM_DMABase_CCR3
- * @arg TIM_DMABase_CCR4
- * @arg TIM_DMABase_DCR
- * @param BurstRequestSrc: TIM DMA Request sources
- * This parameters can be on of the following values:
- * @arg TIM_DMA_UPDATE: TIM update Interrupt source
- * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
- * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
- * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
- * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
- * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source
- * @param BurstBuffer: The Buffer address.
- * @param BurstLength: DMA Burst length. This parameter can be one value
- * between: TIM_DMABurstLength_1Transfer and TIM_DMABurstLength_18Transfers.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc,
- uint32_t* BurstBuffer, uint32_t BurstLength)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance));
- assert_param(IS_TIM_DMA_BASE(BurstBaseAddress));
- assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
- assert_param(IS_TIM_DMA_LENGTH(BurstLength));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if((BurstBuffer == 0 ) && (BurstLength > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch(BurstRequestSrc)
- {
- case TIM_DMA_UPDATE:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC3:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC4:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_TRIGGER:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
- }
- break;
- default:
- break;
- }
- /* configure the DMA Burst Mode */
- htim->Instance->DCR = BurstBaseAddress | BurstLength;
-
- /* Enable the TIM DMA Request */
- __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc);
-
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stops the TIM DMA Burst mode
- * @param htim: TIM handle
- * @param BurstRequestSrc: TIM DMA Request sources to disable
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
-
- /* Abort the DMA transfer (at least disable the DMA channel) */
- switch(BurstRequestSrc)
- {
- case TIM_DMA_UPDATE:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]);
- }
- break;
- case TIM_DMA_CC1:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]);
- }
- break;
- case TIM_DMA_CC2:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]);
- }
- break;
- case TIM_DMA_CC3:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]);
- }
- break;
- case TIM_DMA_CC4:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]);
- }
- break;
- case TIM_DMA_TRIGGER:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]);
- }
- break;
- default:
- break;
- }
-
- /* Disable the TIM Update DMA request */
- __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Configure the DMA Burst to transfer Data from the TIM peripheral to the memory
- * @param htim: TIM handle
- * @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data read
- * This parameters can be on of the following values:
- * @arg TIM_DMABase_CR1
- * @arg TIM_DMABase_CR2
- * @arg TIM_DMABase_SMCR
- * @arg TIM_DMABase_DIER
- * @arg TIM_DMABase_SR
- * @arg TIM_DMABase_EGR
- * @arg TIM_DMABase_CCMR1
- * @arg TIM_DMABase_CCMR2
- * @arg TIM_DMABase_CCER
- * @arg TIM_DMABase_CNT
- * @arg TIM_DMABase_PSC
- * @arg TIM_DMABase_ARR
- * @arg TIM_DMABase_RCR
- * @arg TIM_DMABase_CCR1
- * @arg TIM_DMABase_CCR2
- * @arg TIM_DMABase_CCR3
- * @arg TIM_DMABase_CCR4
- * @arg TIM_DMABase_BDTR
- * @arg TIM_DMABase_DCR
- * @param BurstRequestSrc: TIM DMA Request sources
- * This parameters can be on of the following values:
- * @arg TIM_DMA_UPDATE: TIM update Interrupt source
- * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
- * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
- * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
- * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
- * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source
- * @param BurstBuffer: The Buffer address.
- * @param BurstLength: DMA Burst length. This parameter can be one value
- * between: TIM_DMABurstLength_1Transfer and TIM_DMABurstLength_18Transfers.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc,
- uint32_t *BurstBuffer, uint32_t BurstLength)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance));
- assert_param(IS_TIM_DMA_BASE(BurstBaseAddress));
- assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
- assert_param(IS_TIM_DMA_LENGTH(BurstLength));
-
- if((htim->State == HAL_TIM_STATE_BUSY))
- {
- return HAL_BUSY;
- }
- else if((htim->State == HAL_TIM_STATE_READY))
- {
- if((BurstBuffer == 0 ) && (BurstLength > 0))
- {
- return HAL_ERROR;
- }
- else
- {
- htim->State = HAL_TIM_STATE_BUSY;
- }
- }
- else
- {
- return HAL_ERROR;
- }
-
- switch(BurstRequestSrc)
- {
- case TIM_DMA_UPDATE:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC1:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC2:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC3:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_CC4:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- case TIM_DMA_TRIGGER:
- {
- /* Set the DMA Period elapsed callback */
- htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt;
-
- /* Set the DMA error callback */
- htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ;
-
- /* Enable the DMA channel */
- HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8) + 1);
- }
- break;
- default:
- break;
- }
-
- /* configure the DMA Burst Mode */
- htim->Instance->DCR = BurstBaseAddress | BurstLength;
-
- /* Enable the TIM DMA Request */
- __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc);
-
- htim->State = HAL_TIM_STATE_READY;
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Stop the DMA burst reading
- * @param htim: TIM handle
- * @param BurstRequestSrc: TIM DMA Request sources to disable.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
-{
- /* Check the parameters */
- assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
-
- /* Abort the DMA transfer (at least disable the DMA channel) */
- switch(BurstRequestSrc)
- {
- case TIM_DMA_UPDATE:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]);
- }
- break;
- case TIM_DMA_CC1:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]);
- }
- break;
- case TIM_DMA_CC2:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]);
- }
- break;
- case TIM_DMA_CC3:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]);
- }
- break;
- case TIM_DMA_CC4:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]);
- }
- break;
- case TIM_DMA_TRIGGER:
- {
- HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]);
- }
- break;
- default:
- break;
- }
-
- /* Disable the TIM Update DMA request */
- __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Generate a software event
- * @param htim: TIM handle
- * @param EventSource: specifies the event source.
- * This parameter can be one of the following values:
- * @arg TIM_EventSource_Update: Timer update Event source
- * @arg TIM_EventSource_CC1: Timer Capture Compare 1 Event source
- * @arg TIM_EventSource_CC2: Timer Capture Compare 2 Event source
- * @arg TIM_EventSource_CC3: Timer Capture Compare 3 Event source
- * @arg TIM_EventSource_CC4: Timer Capture Compare 4 Event source
- * @arg TIM_EventSource_COM: Timer COM event source
- * @arg TIM_EventSource_Trigger: Timer Trigger Event source
- * @arg TIM_EventSource_Break: Timer Break event source
- * @note TBC can only generate an update event.
- * @note TIM_EventSource_COM and TIM_EventSource_Break are used only with TBC.
- * @retval HAL status
- */
-
-HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef *htim, uint32_t EventSource)
-{
- /* Check the parameters */
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- assert_param(IS_TIM_EVENT_SOURCE(EventSource));
-
- /* Process Locked */
- __HAL_LOCK(htim);
-
- /* Change the TIM state */
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Set the event sources */
- htim->Instance->EGR = EventSource;
-
- /* Change the TIM state */
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- /* Return function status */
- return HAL_OK;
-}
-
-/**
- * @brief Configures the OCRef clear feature
- * @param htim: TIM handle
- * @param sClearInputConfig: pointer to a TIM_ClearInputConfigTypeDef structure that
- * contains the OCREF clear feature and parameters for the TIM peripheral.
- * @param Channel: specifies the TIM Channel
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1
- * @arg TIM_CHANNEL_2: TIM Channel 2
- * @arg TIM_CHANNEL_3: TIM Channel 3
- * @arg TIM_CHANNEL_4: TIM Channel 4
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef *htim, TIM_ClearInputConfigTypeDef * sClearInputConfig, uint32_t Channel)
-{
-
- /* Check the parameters */
- assert_param(IS_TIM_OCXREF_CLEAR_INSTANCE(htim->Instance));
- assert_param(IS_TIM_CLEARINPUT_SOURCE(sClearInputConfig->ClearInputSource));
- assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity));
- assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler));
- assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter));
-
- /* Process Locked */
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- switch (sClearInputConfig->ClearInputSource)
- {
- case TIM_CLEARINPUTSOURCE_NONE:
- {
- /* Clear the OCREF clear selection bit */
- CLEAR_BIT(htim->Instance->SMCR, TIM_SMCR_OCCS);
-
- /* Clear the ETR Bits */
- CLEAR_BIT(htim->Instance->SMCR, (TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP));
-
- }
- break;
-
- case TIM_CLEARINPUTSOURCE_OCREFCLR:
- {
- /* Clear the OCREF clear selection bit */
- CLEAR_BIT(htim->Instance->SMCR, TIM_SMCR_OCCS);
- }
- break;
-
- case TIM_CLEARINPUTSOURCE_ETR:
- {
- TIM_ETR_SetConfig(htim->Instance,
- sClearInputConfig->ClearInputPrescaler,
- sClearInputConfig->ClearInputPolarity,
- sClearInputConfig->ClearInputFilter);
-
- /* Set the OCREF clear selection bit */
- SET_BIT(htim->Instance->SMCR, TIM_SMCR_OCCS);
- }
- break;
-
- default:
- break;
-
- }
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- if(sClearInputConfig->ClearInputState != RESET)
- {
- /* Enable the Ocref clear feature for Channel 1 */
- htim->Instance->CCMR1 |= TIM_CCMR1_OC1CE;
- }
- else
- {
- /* Disable the Ocref clear feature for Channel 1 */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1CE;
- }
- }
- break;
- case TIM_CHANNEL_2:
- {
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- if(sClearInputConfig->ClearInputState != RESET)
- {
- /* Enable the Ocref clear feature for Channel 2 */
- htim->Instance->CCMR1 |= TIM_CCMR1_OC2CE;
- }
- else
- {
- /* Disable the Ocref clear feature for Channel 2 */
- htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2CE;
- }
- }
- break;
- case TIM_CHANNEL_3:
- {
- assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
- if(sClearInputConfig->ClearInputState != RESET)
- {
- /* Enable the Ocref clear feature for Channel 3 */
- htim->Instance->CCMR2 |= TIM_CCMR2_OC3CE;
- }
- else
- {
- /* Disable the Ocref clear feature for Channel 3 */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3CE;
- }
- }
- break;
- case TIM_CHANNEL_4:
- {
- assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
- if(sClearInputConfig->ClearInputState != RESET)
- {
- /* Enable the Ocref clear feature for Channel 4 */
- htim->Instance->CCMR2 |= TIM_CCMR2_OC4CE;
- }
- else
- {
- /* Disable the Ocref clear feature for Channel 4 */
- htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4CE;
- }
- }
- break;
- default:
- break;
- }
-
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Configures the clock source to be used
- * @param htim: TIM handle
- * @param sClockSourceConfig: pointer to a TIM_ClockConfigTypeDef structure that
- * contains the clock source information for the TIM peripheral.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef *htim, TIM_ClockConfigTypeDef * sClockSourceConfig)
-{
- uint32_t tmpsmcr = 0;
-
- /* Check the parameters */
- assert_param(IS_TIM_CLOCKSOURCE(sClockSourceConfig->ClockSource));
- assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
- assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler));
- assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
-
- /* Process Locked */
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Reset the SMS, TS, ECE, ETPS and ETRF bits */
- tmpsmcr = htim->Instance->SMCR;
- tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS);
- tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP);
- htim->Instance->SMCR = tmpsmcr;
-
- switch (sClockSourceConfig->ClockSource)
- {
- case TIM_CLOCKSOURCE_INTERNAL:
- {
- assert_param(IS_TIM_INSTANCE(htim->Instance));
- /* Disable slave mode to clock the prescaler directly with the internal clock */
- htim->Instance->SMCR &= ~TIM_SMCR_SMS;
- }
- break;
-
- case TIM_CLOCKSOURCE_ETRMODE1:
- {
- /* Check whether or not the timer instance supports external trigger input mode 1 (ETRF)*/
- assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance));
-
- /* Configure the ETR Clock source */
- TIM_ETR_SetConfig(htim->Instance,
- sClockSourceConfig->ClockPrescaler,
- sClockSourceConfig->ClockPolarity,
- sClockSourceConfig->ClockFilter);
- /* Get the TIMx SMCR register value */
- tmpsmcr = htim->Instance->SMCR;
- /* Reset the SMS and TS Bits */
- tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS);
- /* Select the External clock mode1 and the ETRF trigger */
- tmpsmcr |= (TIM_SLAVEMODE_EXTERNAL1 | TIM_CLOCKSOURCE_ETRMODE1);
- /* Write to TIMx SMCR */
- htim->Instance->SMCR = tmpsmcr;
- }
- break;
-
- case TIM_CLOCKSOURCE_ETRMODE2:
- {
- /* Check whether or not the timer instance supports external trigger input mode 2 (ETRF)*/
- assert_param(IS_TIM_CLOCKSOURCE_ETRMODE2_INSTANCE(htim->Instance));
-
- /* Configure the ETR Clock source */
- TIM_ETR_SetConfig(htim->Instance,
- sClockSourceConfig->ClockPrescaler,
- sClockSourceConfig->ClockPolarity,
- sClockSourceConfig->ClockFilter);
- /* Enable the External clock mode2 */
- htim->Instance->SMCR |= TIM_SMCR_ECE;
- }
- break;
-
- case TIM_CLOCKSOURCE_TI1:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance));
-
- TIM_TI1_ConfigInputStage(htim->Instance,
- sClockSourceConfig->ClockPolarity,
- sClockSourceConfig->ClockFilter);
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1);
- }
- break;
- case TIM_CLOCKSOURCE_TI2:
- {
- /* Check whether or not the timer instance supports external clock mode 1 (ETRF)*/
- assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance));
-
- TIM_TI2_ConfigInputStage(htim->Instance,
- sClockSourceConfig->ClockPolarity,
- sClockSourceConfig->ClockFilter);
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI2);
- }
- break;
- case TIM_CLOCKSOURCE_TI1ED:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance));
-
- TIM_TI1_ConfigInputStage(htim->Instance,
- sClockSourceConfig->ClockPolarity,
- sClockSourceConfig->ClockFilter);
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1ED);
- }
- break;
- case TIM_CLOCKSOURCE_ITR0:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance));
-
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR0);
- }
- break;
- case TIM_CLOCKSOURCE_ITR1:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance));
-
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR1);
- }
- break;
- case TIM_CLOCKSOURCE_ITR2:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance));
-
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR2);
- }
- break;
- case TIM_CLOCKSOURCE_ITR3:
- {
- /* Check whether or not the timer instance supports external clock mode 1 */
- assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance));
-
- TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR3);
- }
- break;
-
- default:
- break;
- }
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Selects the signal connected to the TI1 input: direct from CH1_input
- * or a XOR combination between CH1_input, CH2_input & CH3_input
- * @param htim: TIM handle.
- * @param TI1_Selection: Indicate whether or not channel 1 is connected to the
- * output of a XOR gate.
- * This parameter can be one of the following values:
- * @arg TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input
- * @arg TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3
- * pins are connected to the TI1 input (XOR combination)
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef *htim, uint32_t TI1_Selection)
-{
- uint32_t tmpcr2 = 0;
-
- /* Check the parameters */
- assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
- assert_param(IS_TIM_TI1SELECTION(TI1_Selection));
-
- /* Get the TIMx CR2 register value */
- tmpcr2 = htim->Instance->CR2;
-
- /* Reset the TI1 selection */
- tmpcr2 &= ~TIM_CR2_TI1S;
-
- /* Set the the TI1 selection */
- tmpcr2 |= TI1_Selection;
-
- /* Write to TIMxCR2 */
- htim->Instance->CR2 = tmpcr2;
-
- return HAL_OK;
-}
-
-/**
- * @brief Configures the TIM in Slave mode
- * @param htim: TIM handle.
- * @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that
- * contains the selected trigger (internal trigger input, filtered
- * timer input or external trigger input) and the ) and the Slave
- * mode (Disable, Reset, Gated, Trigger, External clock mode 1).
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig)
-{
- uint32_t tmpsmcr = 0;
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Check the parameters */
- assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance));
- assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode));
- assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger));
-
- __HAL_LOCK(htim);
-
- htim->State = HAL_TIM_STATE_BUSY;
-
- /* Get the TIMx SMCR register value */
- tmpsmcr = htim->Instance->SMCR;
-
- /* Reset the Trigger Selection Bits */
- tmpsmcr &= ~TIM_SMCR_TS;
- /* Set the Input Trigger source */
- tmpsmcr |= sSlaveConfig->InputTrigger;
-
- /* Reset the slave mode Bits */
- tmpsmcr &= ~TIM_SMCR_SMS;
- /* Set the slave mode */
- tmpsmcr |= sSlaveConfig->SlaveMode;
-
- /* Write to TIMx SMCR */
- htim->Instance->SMCR = tmpsmcr;
-
- /* Configure the trigger prescaler, filter, and polarity */
- switch (sSlaveConfig->InputTrigger)
- {
- case TIM_TS_ETRF:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance));
- assert_param(IS_TIM_TRIGGERPRESCALER(sSlaveConfig->TriggerPrescaler));
- assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
- assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
- /* Configure the ETR Trigger source */
- TIM_ETR_SetConfig(htim->Instance,
- sSlaveConfig->TriggerPrescaler,
- sSlaveConfig->TriggerPolarity,
- sSlaveConfig->TriggerFilter);
- }
- break;
-
- case TIM_TS_TI1F_ED:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
- assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
- assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
-
- /* Disable the Channel 1: Reset the CC1E Bit */
- tmpccer = htim->Instance->CCER;
- htim->Instance->CCER &= ~TIM_CCER_CC1E;
- tmpccmr1 = htim->Instance->CCMR1;
-
- /* Set the filter */
- tmpccmr1 &= ~TIM_CCMR1_IC1F;
- tmpccmr1 |= ((sSlaveConfig->TriggerFilter) << 4);
-
- /* Write to TIMx CCMR1 and CCER registers */
- htim->Instance->CCMR1 = tmpccmr1;
- htim->Instance->CCER = tmpccer;
-
- }
- break;
-
- case TIM_TS_TI1FP1:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
- assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
- assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
-
- /* Configure TI1 Filter and Polarity */
- TIM_TI1_ConfigInputStage(htim->Instance,
- sSlaveConfig->TriggerPolarity,
- sSlaveConfig->TriggerFilter);
- }
- break;
-
- case TIM_TS_TI2FP2:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
- assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
-
- /* Configure TI2 Filter and Polarity */
- TIM_TI2_ConfigInputStage(htim->Instance,
- sSlaveConfig->TriggerPolarity,
- sSlaveConfig->TriggerFilter);
- }
- break;
-
- case TIM_TS_ITR0:
- {
- /* Check the parameter */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- }
- break;
-
- case TIM_TS_ITR1:
- {
- /* Check the parameter */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- }
- break;
-
- case TIM_TS_ITR2:
- {
- /* Check the parameter */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- }
- break;
-
- case TIM_TS_ITR3:
- {
- /* Check the parameter */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
- }
- break;
-
- default:
- break;
- }
-
- htim->State = HAL_TIM_STATE_READY;
-
- __HAL_UNLOCK(htim);
-
- return HAL_OK;
-}
-
-/**
- * @brief Read the captured value from Capture Compare unit
- * @param htim: TIM handle.
- * @param Channel : TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
- * @arg TIM_CHANNEL_3: TIM Channel 3 selected
- * @arg TIM_CHANNEL_4: TIM Channel 4 selected
- * @retval Captured value
- */
-uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef *htim, uint32_t Channel)
-{
- uint32_t tmpreg = 0;
-
- __HAL_LOCK(htim);
-
- switch (Channel)
- {
- case TIM_CHANNEL_1:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
-
- /* Return the capture 1 value */
- tmpreg = htim->Instance->CCR1;
-
- break;
- }
- case TIM_CHANNEL_2:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
-
- /* Return the capture 2 value */
- tmpreg = htim->Instance->CCR2;
-
- break;
- }
-
- case TIM_CHANNEL_3:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
-
- /* Return the capture 3 value */
- tmpreg = htim->Instance->CCR3;
-
- break;
- }
-
- case TIM_CHANNEL_4:
- {
- /* Check the parameters */
- assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
-
- /* Return the capture 4 value */
- tmpreg = htim->Instance->CCR4;
-
- break;
- }
-
- default:
- break;
- }
-
- __HAL_UNLOCK(htim);
- return tmpreg;
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group9 TIM Callbacks functions
- * @brief TIM Callbacks functions
- *
-@verbatim
- ==============================================================================
- ##### TIM Callbacks functions #####
- ==============================================================================
- [..]
- This section provides TIM callback functions:
- (+) Timer Period elapsed callback
- (+) Timer Output Compare callback
- (+) Timer Input capture callback
- (+) Timer Trigger callback
- (+) Timer Error callback
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Period elapsed callback in non blocking mode
- * @param htim : TIM handle
- * @retval None
- */
-__weak void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file
- */
-
-}
-/**
- * @brief Output Compare callback in non blocking mode
- * @param htim : TIM OC handle
- * @retval None
- */
-__weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the __HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file
- */
-}
-/**
- * @brief Input Capture callback in non blocking mode
- * @param htim : TIM IC handle
- * @retval None
- */
-__weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the __HAL_TIM_IC_CaptureCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief PWM Pulse finished callback in non blocking mode
- * @param htim : TIM handle
- * @retval None
- */
-__weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the __HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Hall Trigger detection callback in non blocking mode
- * @param htim : TIM handle
- * @retval None
- */
-__weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_TriggerCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Timer error callback in non blocking mode
- * @param htim : TIM handle
- * @retval None
- */
-__weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef *htim)
-{
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_TIM_ErrorCallback could be implemented in the user file
- */
-}
-
-/**
- * @}
- */
-
-/** @defgroup TIM_Exported_Functions_Group10 Peripheral State functions
- * @brief Peripheral State functions
- *
-@verbatim
- ==============================================================================
- ##### Peripheral State functions #####
- ==============================================================================
- [..]
- This subsection permit to get in run-time the status of the peripheral
- and the data flow.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Return the TIM Base state
- * @param htim: TIM Base handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @brief Return the TIM OC state
- * @param htim: TIM Ouput Compare handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @brief Return the TIM PWM state
- * @param htim: TIM handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @brief Return the TIM Input Capture state
- * @param htim: TIM IC handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @brief Return the TIM One Pulse Mode state
- * @param htim: TIM OPM handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @brief Return the TIM Encoder Mode state
- * @param htim: TIM Encoder handle
- * @retval HAL state
- */
-HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef *htim)
-{
- return htim->State;
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-
-/** @addtogroup TIM_Private_Functions
- * @{
- */
-
-
-/**
- * @brief TIM DMA error callback
- * @param hdma : pointer to DMA handle.
- * @retval None
- */
-static void TIM_DMAError(DMA_HandleTypeDef *hdma)
-{
- TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
-
- htim->State= HAL_TIM_STATE_READY;
-
- HAL_TIM_ErrorCallback(htim);
-}
-
-/**
- * @brief TIM DMA Delay Pulse complete callback.
- * @param hdma : pointer to DMA handle.
- * @retval None
- */
-static void TIM_DMADelayPulseCplt(DMA_HandleTypeDef *hdma)
-{
- TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
-
- htim->State= HAL_TIM_STATE_READY;
-
- if (hdma == htim->hdma[TIM_DMA_ID_CC1])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC2])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC3])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC4])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
- }
-
- HAL_TIM_PWM_PulseFinishedCallback(htim);
-
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
-}
-
-/**
- * @brief TIM DMA Capture complete callback.
- * @param hdma : pointer to DMA handle.
- * @retval None
- */
-static void TIM_DMACaptureCplt(DMA_HandleTypeDef *hdma)
-{
- TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
-
- htim->State= HAL_TIM_STATE_READY;
-
- if (hdma == htim->hdma[TIM_DMA_ID_CC1])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC2])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC3])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
- }
- else if (hdma == htim->hdma[TIM_DMA_ID_CC4])
- {
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
- }
-
- HAL_TIM_IC_CaptureCallback(htim);
-
- htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
-}
-
-/**
- * @brief TIM DMA Period Elapse complete callback.
- * @param hdma : pointer to DMA handle.
- * @retval None
- */
-static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma)
-{
- TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
-
- htim->State= HAL_TIM_STATE_READY;
-
- HAL_TIM_PeriodElapsedCallback(htim);
-}
-
-/**
- * @brief TIM DMA Trigger callback.
- * @param hdma : pointer to DMA handle.
- * @retval None
- */
-static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma)
-{
- TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
-
- htim->State= HAL_TIM_STATE_READY;
-
- HAL_TIM_TriggerCallback(htim);
-}
-
-/**
- * @brief Time Base configuration
- * @param TIMx: TIM periheral
- * @param Structure: TIM Base configuration structure
- * @retval None
- */
-static void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure)
-{
- uint32_t tmpcr1 = 0;
- tmpcr1 = TIMx->CR1;
-
- /* Set TIM Time Base Unit parameters ---------------------------------------*/
- if (IS_TIM_COUNTER_MODE_SELECT_INSTANCE(TIMx))
- {
- /* Select the Counter Mode */
- tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS);
- tmpcr1 |= Structure->CounterMode;
- }
-
- if(IS_TIM_CLOCK_DIVISION_INSTANCE(TIMx))
- {
- /* Set the clock division */
- tmpcr1 &= ~TIM_CR1_CKD;
- tmpcr1 |= (uint32_t)Structure->ClockDivision;
- }
-
- TIMx->CR1 = tmpcr1;
-
- /* Set the Autoreload value */
- TIMx->ARR = (uint32_t)Structure->Period ;
-
- /* Set the Prescaler value */
- TIMx->PSC = (uint32_t)Structure->Prescaler;
-
- /* Generate an update event to reload the Prescaler
- and the repetition counter(only for TIM1 and TIM8) value immediatly */
- TIMx->EGR = TIM_EGR_UG;
-}
-
-/**
- * @brief Time Ouput Compare 1 configuration
- * @param TIMx to select the TIM peripheral
- * @param OC_Config: The ouput configuration structure
- * @retval None
- */
-static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
-{
- uint32_t tmpccmrx = 0;
- uint32_t tmpccer = 0;
- uint32_t tmpcr2 = 0;
-
- /* Disable the Channel 1: Reset the CC1E Bit */
- TIMx->CCER &= ~TIM_CCER_CC1E;
-
- /* Get the TIMx CCER register value */
- tmpccer = TIMx->CCER;
- /* Get the TIMx CR2 register value */
- tmpcr2 = TIMx->CR2;
-
- /* Get the TIMx CCMR1 register value */
- tmpccmrx = TIMx->CCMR1;
-
- /* Reset the Output Compare Mode Bits */
- tmpccmrx &= ~TIM_CCMR1_OC1M;
- tmpccmrx &= ~TIM_CCMR1_CC1S;
- /* Select the Output Compare Mode */
- tmpccmrx |= OC_Config->OCMode;
-
- /* Reset the Output Polarity level */
- tmpccer &= ~TIM_CCER_CC1P;
- /* Set the Output Compare Polarity */
- tmpccer |= OC_Config->OCPolarity;
-
- /* Write to TIMx CR2 */
- TIMx->CR2 = tmpcr2;
-
- /* Write to TIMx CCMR1 */
- TIMx->CCMR1 = tmpccmrx;
-
- /* Set the Capture Compare Register value */
- TIMx->CCR1 = OC_Config->Pulse;
-
- /* Write to TIMx CCER */
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Time Ouput Compare 2 configuration
- * @param TIMx to select the TIM peripheral
- * @param OC_Config: The ouput configuration structure
- * @retval None
- */
-static void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
-{
- uint32_t tmpccmrx = 0;
- uint32_t tmpccer = 0;
- uint32_t tmpcr2 = 0;
-
- /* Disable the Channel 2: Reset the CC2E Bit */
- TIMx->CCER &= ~TIM_CCER_CC2E;
-
- /* Get the TIMx CCER register value */
- tmpccer = TIMx->CCER;
- /* Get the TIMx CR2 register value */
- tmpcr2 = TIMx->CR2;
-
- /* Get the TIMx CCMR1 register value */
- tmpccmrx = TIMx->CCMR1;
-
- /* Reset the Output Compare mode and Capture/Compare selection Bits */
- tmpccmrx &= ~TIM_CCMR1_OC2M;
- tmpccmrx &= ~TIM_CCMR1_CC2S;
-
- /* Select the Output Compare Mode */
- tmpccmrx |= (OC_Config->OCMode << 8);
-
- /* Reset the Output Polarity level */
- tmpccer &= ~TIM_CCER_CC2P;
- /* Set the Output Compare Polarity */
- tmpccer |= (OC_Config->OCPolarity << 4);
-
- /* Write to TIMx CR2 */
- TIMx->CR2 = tmpcr2;
-
- /* Write to TIMx CCMR1 */
- TIMx->CCMR1 = tmpccmrx;
-
- /* Set the Capture Compare Register value */
- TIMx->CCR2 = OC_Config->Pulse;
-
- /* Write to TIMx CCER */
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Time Ouput Compare 3 configuration
- * @param TIMx to select the TIM peripheral
- * @param OC_Config: The ouput configuration structure
- * @retval None
- */
-static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
-{
- uint32_t tmpccmrx = 0;
- uint32_t tmpccer = 0;
- uint32_t tmpcr2 = 0;
-
- /* Disable the Channel 3: Reset the CC2E Bit */
- TIMx->CCER &= ~TIM_CCER_CC3E;
-
- /* Get the TIMx CCER register value */
- tmpccer = TIMx->CCER;
- /* Get the TIMx CR2 register value */
- tmpcr2 = TIMx->CR2;
-
- /* Get the TIMx CCMR2 register value */
- tmpccmrx = TIMx->CCMR2;
-
- /* Reset the Output Compare mode and Capture/Compare selection Bits */
- tmpccmrx &= ~TIM_CCMR2_OC3M;
- tmpccmrx &= ~TIM_CCMR2_CC3S;
- /* Select the Output Compare Mode */
- tmpccmrx |= OC_Config->OCMode;
-
- /* Reset the Output Polarity level */
- tmpccer &= ~TIM_CCER_CC3P;
- /* Set the Output Compare Polarity */
- tmpccer |= (OC_Config->OCPolarity << 8);
-
- /* Write to TIMx CR2 */
- TIMx->CR2 = tmpcr2;
-
- /* Write to TIMx CCMR2 */
- TIMx->CCMR2 = tmpccmrx;
-
- /* Set the Capture Compare Register value */
- TIMx->CCR3 = OC_Config->Pulse;
-
- /* Write to TIMx CCER */
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Time Ouput Compare 4 configuration
- * @param TIMx to select the TIM peripheral
- * @param OC_Config: The ouput configuration structure
- * @retval None
- */
-static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
-{
- uint32_t tmpccmrx = 0;
- uint32_t tmpccer = 0;
- uint32_t tmpcr2 = 0;
-
- /* Disable the Channel 4: Reset the CC4E Bit */
- TIMx->CCER &= ~TIM_CCER_CC4E;
-
- /* Get the TIMx CCER register value */
- tmpccer = TIMx->CCER;
- /* Get the TIMx CR2 register value */
- tmpcr2 = TIMx->CR2;
-
- /* Get the TIMx CCMR2 register value */
- tmpccmrx = TIMx->CCMR2;
-
- /* Reset the Output Compare mode and Capture/Compare selection Bits */
- tmpccmrx &= ~TIM_CCMR2_OC4M;
- tmpccmrx &= ~TIM_CCMR2_CC4S;
-
- /* Select the Output Compare Mode */
- tmpccmrx |= (OC_Config->OCMode << 8);
-
- /* Reset the Output Polarity level */
- tmpccer &= ~TIM_CCER_CC4P;
- /* Set the Output Compare Polarity */
- tmpccer |= (OC_Config->OCPolarity << 12);
-
- /* Write to TIMx CR2 */
- TIMx->CR2 = tmpcr2;
-
- /* Write to TIMx CCMR2 */
- TIMx->CCMR2 = tmpccmrx;
-
- /* Set the Capture Compare Register value */
- TIMx->CCR4 = OC_Config->Pulse;
-
- /* Write to TIMx CCER */
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the TI1 as Input.
- * @param TIMx to select the TIM peripheral.
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICSelection: specifies the input to be used.
- * This parameter can be one of the following values:
- * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 1 is selected to be connected to IC1.
- * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 1 is selected to be connected to IC2.
- * @arg TIM_ICSELECTION_TRC: TIM Input 1 is selected to be connected to TRC.
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 1: Reset the CC1E Bit */
- TIMx->CCER &= ~TIM_CCER_CC1E;
- tmpccmr1 = TIMx->CCMR1;
- tmpccer = TIMx->CCER;
-
- /* Select the Input */
- if(IS_TIM_CC2_INSTANCE(TIMx) != RESET)
- {
- tmpccmr1 &= ~TIM_CCMR1_CC1S;
- tmpccmr1 |= TIM_ICSelection;
- }
- else
- {
- tmpccmr1 |= TIM_CCMR1_CC1S_0;
- }
-
- /* Set the filter */
- tmpccmr1 &= ~TIM_CCMR1_IC1F;
- tmpccmr1 |= (TIM_ICFilter << 4);
-
- /* Select the Polarity and set the CC1E Bit */
- tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP);
- tmpccer |= TIM_ICPolarity;
-
- /* Write to TIMx CCMR1 and CCER registers */
- TIMx->CCMR1 = tmpccmr1;
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the Polarity and Filter for TI1.
- * @param TIMx to select the TIM peripheral.
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 1: Reset the CC1E Bit */
- tmpccer = TIMx->CCER;
- TIMx->CCER &= ~TIM_CCER_CC1E;
- tmpccmr1 = TIMx->CCMR1;
-
- /* Set the filter */
- tmpccmr1 &= ~TIM_CCMR1_IC1F;
- tmpccmr1 |= (TIM_ICFilter << 4);
-
- /* Select the Polarity and set the CC1E Bit */
- tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP);
- tmpccer |= TIM_ICPolarity;
-
- /* Write to TIMx CCMR1 and CCER registers */
- TIMx->CCMR1 = tmpccmr1;
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the TI2 as Input.
- * @param TIMx to select the TIM peripheral
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICSelection: specifies the input to be used.
- * This parameter can be one of the following values:
- * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 2 is selected to be connected to IC2.
- * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 2 is selected to be connected to IC1.
- * @arg TIM_ICSELECTION_TRC: TIM Input 2 is selected to be connected to TRC.
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 2: Reset the CC2E Bit */
- TIMx->CCER &= ~TIM_CCER_CC2E;
- tmpccmr1 = TIMx->CCMR1;
- tmpccer = TIMx->CCER;
-
- /* Select the Input */
- tmpccmr1 &= ~TIM_CCMR1_CC2S;
- tmpccmr1 |= (TIM_ICSelection << 8);
-
- /* Set the filter */
- tmpccmr1 &= ~TIM_CCMR1_IC2F;
- tmpccmr1 |= (TIM_ICFilter << 12);
-
- /* Select the Polarity and set the CC2E Bit */
- tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP);
- tmpccer |= (TIM_ICPolarity << 4);
-
- /* Write to TIMx CCMR1 and CCER registers */
- TIMx->CCMR1 = tmpccmr1 ;
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the Polarity and Filter for TI2.
- * @param TIMx to select the TIM peripheral.
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr1 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 2: Reset the CC2E Bit */
- TIMx->CCER &= ~TIM_CCER_CC2E;
- tmpccmr1 = TIMx->CCMR1;
- tmpccer = TIMx->CCER;
-
- /* Set the filter */
- tmpccmr1 &= ~TIM_CCMR1_IC2F;
- tmpccmr1 |= (TIM_ICFilter << 12);
-
- /* Select the Polarity and set the CC2E Bit */
- tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP);
- tmpccer |= (TIM_ICPolarity << 4);
-
- /* Write to TIMx CCMR1 and CCER registers */
- TIMx->CCMR1 = tmpccmr1 ;
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the TI3 as Input.
- * @param TIMx to select the TIM peripheral
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICSelection: specifies the input to be used.
- * This parameter can be one of the following values:
- * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 3 is selected to be connected to IC3.
- * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 3 is selected to be connected to IC4.
- * @arg TIM_ICSELECTION_TRC: TIM Input 3 is selected to be connected to TRC.
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr2 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 3: Reset the CC3E Bit */
- TIMx->CCER &= ~TIM_CCER_CC3E;
- tmpccmr2 = TIMx->CCMR2;
- tmpccer = TIMx->CCER;
-
- /* Select the Input */
- tmpccmr2 &= ~TIM_CCMR2_CC3S;
- tmpccmr2 |= TIM_ICSelection;
-
- /* Set the filter */
- tmpccmr2 &= ~TIM_CCMR2_IC3F;
- tmpccmr2 |= (TIM_ICFilter << 4);
-
- /* Select the Polarity and set the CC3E Bit */
- tmpccer &= ~(TIM_CCER_CC3P | TIM_CCER_CC3NP);
- tmpccer |= (TIM_ICPolarity << 8);
-
- /* Write to TIMx CCMR2 and CCER registers */
- TIMx->CCMR2 = tmpccmr2;
- TIMx->CCER = tmpccer;
-}
-
-/**
- * @brief Configure the TI4 as Input.
- * @param TIMx to select the TIM peripheral
- * @param TIM_ICPolarity : The Input Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ICPOLARITY_RISING
- * @arg TIM_ICPOLARITY_FALLING
- * @arg TIM_ICPOLARITY_BOTHEDGE
- * @param TIM_ICSelection: specifies the input to be used.
- * This parameter can be one of the following values:
- * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 4 is selected to be connected to IC4.
- * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 4 is selected to be connected to IC3.
- * @arg TIM_ICSELECTION_TRC: TIM Input 4 is selected to be connected to TRC.
- * @param TIM_ICFilter: Specifies the Input Capture Filter.
- * This parameter must be a value between 0x00 and 0x0F.
- * @retval None
- */
-static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
- uint32_t TIM_ICFilter)
-{
- uint32_t tmpccmr2 = 0;
- uint32_t tmpccer = 0;
-
- /* Disable the Channel 4: Reset the CC4E Bit */
- TIMx->CCER &= ~TIM_CCER_CC4E;
- tmpccmr2 = TIMx->CCMR2;
- tmpccer = TIMx->CCER;
-
- /* Select the Input */
- tmpccmr2 &= ~TIM_CCMR2_CC4S;
- tmpccmr2 |= (TIM_ICSelection << 8);
-
- /* Set the filter */
- tmpccmr2 &= ~TIM_CCMR2_IC4F;
- tmpccmr2 |= (TIM_ICFilter << 12);
-
- /* Select the Polarity and set the CC4E Bit */
- tmpccer &= ~(TIM_CCER_CC4P | TIM_CCER_CC4NP);
- tmpccer |= (TIM_ICPolarity << 12);
-
- /* Write to TIMx CCMR2 and CCER registers */
- TIMx->CCMR2 = tmpccmr2;
- TIMx->CCER = tmpccer ;
-}
-
-/**
- * @brief Selects the Input Trigger source
- * @param TIMx to select the TIM peripheral
- * @param InputTriggerSource: The Input Trigger source.
- * This parameter can be one of the following values:
- * @arg TIM_TS_ITR0: Internal Trigger 0
- * @arg TIM_TS_ITR1: Internal Trigger 1
- * @arg TIM_TS_ITR2: Internal Trigger 2
- * @arg TIM_TS_ITR3: Internal Trigger 3
- * @arg TIM_TS_TI1F_ED: TI1 Edge Detector
- * @arg TIM_TS_TI1FP1: Filtered Timer Input 1
- * @arg TIM_TS_TI2FP2: Filtered Timer Input 2
- * @arg TIM_TS_ETRF: External Trigger input
- * @retval None
- */
-static void TIM_ITRx_SetConfig(TIM_TypeDef *TIMx, uint16_t InputTriggerSource)
-{
- uint32_t tmpsmcr = 0;
-
- /* Get the TIMx SMCR register value */
- tmpsmcr = TIMx->SMCR;
- /* Reset the TS Bits */
- tmpsmcr &= ~TIM_SMCR_TS;
- /* Set the Input Trigger source and the slave mode*/
- tmpsmcr |= InputTriggerSource | TIM_SLAVEMODE_EXTERNAL1;
- /* Write to TIMx SMCR */
- TIMx->SMCR = tmpsmcr;
-}
-/**
- * @brief Configures the TIMx External Trigger (ETR).
- * @param TIMx to select the TIM peripheral
- * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
- * This parameter can be one of the following values:
- * @arg TIM_ETRPRESCALER_DIV1: ETRP Prescaler OFF.
- * @arg TIM_ETRPRESCALER_DIV2: ETRP frequency divided by 2.
- * @arg TIM_ETRPRESCALER_DIV4: ETRP frequency divided by 4.
- * @arg TIM_ETRPRESCALER_DIV8: ETRP frequency divided by 8.
- * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
- * This parameter can be one of the following values:
- * @arg TIM_ETRPOLARITY_INVERTED: active low or falling edge active.
- * @arg TIM_ETRPOLARITY_NONINVERTED: active high or rising edge active.
- * @param ExtTRGFilter: External Trigger Filter.
- * This parameter must be a value between 0x00 and 0x0F
- * @retval None
- */
-static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler,
- uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter)
-{
- uint32_t tmpsmcr = 0;
-
- tmpsmcr = TIMx->SMCR;
-
- /* Reset the ETR Bits */
- tmpsmcr &= (uint32_t)(~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP));
-
- /* Set the Prescaler, the Filter value and the Polarity */
- tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8)));
-
- /* Write to TIMx SMCR */
- TIMx->SMCR = tmpsmcr;
-}
-
-/**
- * @brief Enables or disables the TIM Capture Compare Channel x.
- * @param TIMx to select the TIM peripheral
- * @param Channel: specifies the TIM Channel
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1
- * @arg TIM_CHANNEL_2: TIM Channel 2
- * @arg TIM_CHANNEL_3: TIM Channel 3
- * @arg TIM_CHANNEL_4: TIM Channel 4
- * @param ChannelState: specifies the TIM Channel CCxE bit new state.
- * This parameter can be: TIM_CCx_ENABLE or TIM_CCx_Disable.
- * @retval None
- */
-static void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState)
-{
- uint32_t tmp = 0;
-
- /* Check the parameters */
- assert_param(IS_TIM_CC1_INSTANCE(TIMx));
- assert_param(IS_TIM_CHANNELS(Channel));
-
- tmp = (uint16_t)(TIM_CCER_CC1E << Channel);
-
- /* Reset the CCxE Bit */
- TIMx->CCER &= ~tmp;
-
- /* Set or reset the CCxE Bit */
- TIMx->CCER |= (uint32_t)(ChannelState << Channel);
-}
-
-/**
- * @}
- */
-
-#endif /* HAL_TIM_MODULE_ENABLED */
-
-
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
