Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F334C8/stm32f3xx_hal_pwr_ex.c

Revision:

381:5460fc57b6e4

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F334C8/stm32f3xx_hal_pwr_ex.c	Mon Nov 03 10:30:07 2014 +0000
@@ -0,0 +1,289 @@
+/**
+  ******************************************************************************
+  * @file    stm32f3xx_hal_pwr_ex.c
+  * @author  MCD Application Team
+  * @version V1.1.0
+  * @date    12-Sept-2014
+  * @brief   Extended PWR HAL module driver.
+  *
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Power Controller (PWR) peripheral:
+  *           + Extended Initialization and de-initialization functions
+  *           + Extended Peripheral Control functions
+  *         
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f3xx_hal.h"
+
+/** @addtogroup STM32F3xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWREx PWR Extended HAL module driver
+  * @brief    PWREx HAL module driver
+  * @{
+  */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup PWREx_Private_Constants PWR Extended Private Constants
+  * @{
+  */
+#define PVD_MODE_IT               ((uint32_t)0x00010000)
+#define PVD_MODE_EVT              ((uint32_t)0x00020000)
+#define PVD_RISING_EDGE           ((uint32_t)0x00000001)
+#define PVD_FALLING_EDGE          ((uint32_t)0x00000002)
+/**
+  * @}
+  */
+ 
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions ---------------------------------------------------------*/
+
+/** @defgroup PWREx_Exported_Functions PWR Extended Exported Functions
+  * @{
+  */
+
+/** @defgroup PWREx_Exported_Functions_Group1 Peripheral Extended Control Functions
+  *  @brief   Extended Peripheral Control functions
+  *
+@verbatim
+
+ ===============================================================================
+                 ##### Peripheral Extended control functions #####
+ ===============================================================================
+    *** PVD configuration (present on all other devices than STM32F3x8 devices) ***
+    =========================
+    [..]
+      (+) The PVD is used to monitor the VDD power supply by comparing it to a
+          threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
+      (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
+          than the PVD threshold. This event is internally connected to the EXTI
+          line16 and can generate an interrupt if enabled. This is done through
+          __HAL_PVD_EXTI_ENABLE_IT() macro
+      (+) The PVD is stopped in Standby mode.
+      (+) Note: PVD is not available on STM32F3x8 Product Line
+
+
+    *** Voltage regulator ***
+    =========================
+      (+) The voltage regulator is always enabled after Reset. It works in three different
+          modes:
+          In Run mode, the regulator supplies full power to the 1.8V domain (core, memories
+          and digital peripherals).
+          In Stop mode, the regulator supplies low power to the 1.8V domain, preserving
+          contents of registers and SRAM.
+          In Stop mode, the regulator is powered off. The contents of the registers and SRAM
+          are lost except for the Standby circuitry and the Backup Domain.
+          Note: In the STM32F3x8xx devices, the voltage regulator is bypassed and the
+          microcontroller must be powered from a nominal VDD = 1.8V +/-8% voltage.
+
+
+      (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
+          than the PVD threshold. This event is internally connected to the EXTI
+          line16 and can generate an interrupt if enabled. This is done through
+          __HAL_PVD_EXTI_ENABLE_IT() macro
+      (+) The PVD is stopped in Standby mode.
+
+
+    *** SDADC power configuration ***
+    ================================
+      (+) On STM32F373xC/STM32F378xx devices, there are up to 
+          3 SDADC instances that can be enabled/disabled.
+
+@endverbatim
+  * @{
+  */
+
+#if defined(STM32F302xE) || defined(STM32F303xE) || \
+    defined(STM32F302xC) || defined(STM32F303xC) || \
+    defined(STM32F303x8) || defined(STM32F334x8) || \
+    defined(STM32F301x8) || defined(STM32F302x8) || \
+    defined(STM32F373xC)
+
+/**
+  * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
+  * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration
+  *        information for the PVD.
+  * @note Refer to the electrical characteristics of your device datasheet for
+  *         more details about the voltage threshold corresponding to each
+  *         detection level.
+  * @retval None
+  */
+void HAL_PWR_PVDConfig(PWR_PVDTypeDef *sConfigPVD)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
+  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));
+
+  /* Set PLS[7:5] bits according to PVDLevel value */
+  MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);
+  
+  /* Clear any previous config. Keep it clear if no event or IT mode is selected */
+  __HAL_PWR_PVD_EXTI_DISABLE_EVENT();
+  __HAL_PWR_PVD_EXTI_DISABLE_IT();
+  __HAL_PWR_PVD_EXTI_CLEAR_EGDE_TRIGGER();
+
+  /* Configure interrupt mode */
+  if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_IT();
+  }
+  
+  /* Configure event mode */
+  if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
+  {
+    __HAL_PWR_PVD_EXTI_ENABLE_EVENT();
+  }
+  
+  /* Configure the edge */
+  if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_SET_RISING_EDGE_TRIGGER();
+  }
+  
+  if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
+  {
+    __HAL_PWR_PVD_EXTI_SET_FALLING_EGDE_TRIGGER();
+  }
+}
+
+/**
+  * @brief Enables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_EnablePVD(void)
+{
+  *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)ENABLE;
+}
+
+/**
+  * @brief Disables the Power Voltage Detector(PVD).
+  * @retval None
+  */
+void HAL_PWR_DisablePVD(void)
+{
+  *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)DISABLE;
+}
+
+/**
+  * @brief This function handles the PWR PVD interrupt request.
+  * @note This API should be called under the PVD_IRQHandler().
+  * @retval None
+  */
+void HAL_PWR_PVD_IRQHandler(void)
+{
+  /* Check PWR exti flag */
+  if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET)
+  {
+    /* PWR PVD interrupt user callback */
+    HAL_PWR_PVDCallback();
+
+    /* Clear PWR Exti pending bit */
+    __HAL_PWR_PVD_EXTI_CLEAR_FLAG();
+  }
+}
+
+/**
+  * @brief PWR PVD interrupt callback
+  * @retval None
+  */
+__weak void HAL_PWR_PVDCallback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_PWR_PVDCallback could be implemented in the user file
+   */
+}
+
+#endif /* STM32F302xE || STM32F303xE || */
+       /* STM32F302xC || STM32F303xC || */
+       /* STM32F303x8 || STM32F334x8 || */
+       /* STM32F301x8 || STM32F302x8 || */
+       /* STM32F373xC                   */
+
+#if defined(STM32F373xC) || defined(STM32F378xx)
+
+/**
+  * @brief  Enables the SDADC peripheral functionaliy
+  * @param  Analogx: specifies the SDADC peripheral instance.
+  *   This parameter can be: PWR_SDADC_ANALOG1, PWR_SDADC_ANALOG2 or PWR_SDADC_ANALOG3.
+  * @retval None
+  */
+void HAL_PWREx_EnableSDADCAnalog(uint32_t Analogx)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_SDADC_ANALOG(Analogx));
+
+  /* Enable PWR clock interface for SDADC use */
+  __PWR_CLK_ENABLE();
+    
+  PWR->CR |= Analogx;
+}
+
+/**
+  * @brief  Disables the SDADC peripheral functionaliy
+  * @param  Analogx: specifies the SDADC peripheral instance.
+  *   This parameter can be: PWR_SDADC_ANALOG1, PWR_SDADC_ANALOG2 or PWR_SDADC_ANALOG3.
+  * @retval None
+  */
+void HAL_PWREx_DisableSDADCAnalog(uint32_t Analogx)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_SDADC_ANALOG(Analogx));
+  
+  PWR->CR &= ~Analogx;
+}
+
+#endif /* STM32F373xC || STM32F378xx */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_PWR_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/