File content as of revision 106:ced8cbb51063:

/**
  ******************************************************************************
  * @file    stm32f0xx_gpio.c
  * @author  MCD Application Team
  * @version V1.3.0
  * @date    16-January-2014
  * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the GPIO peripheral:
  *           + Initialization and Configuration functions
  *           + GPIO Read and Write functions
  *           + GPIO Alternate functions configuration functions
  *
  *  @verbatim
  *
  *
    ===========================================================================
                         ##### How to use this driver #####
    ===========================================================================
      [..]
      (#) Enable the GPIO AHB clock using RCC_AHBPeriphClockCmd()
      (#) Configure the GPIO pin(s) using GPIO_Init()
          Four possible configuration are available for each pin:
         (++) Input: Floating, Pull-up, Pull-down.
         (++) Output: Push-Pull (Pull-up, Pull-down or no Pull)
                      Open Drain (Pull-up, Pull-down or no Pull).
              In output mode, the speed is configurable: Low, Medium, Fast or High.
         (++) Alternate Function: Push-Pull (Pull-up, Pull-down or no Pull)
                                  Open Drain (Pull-up, Pull-down or no Pull).
         (++) Analog: required mode when a pin is to be used as ADC channel,
              DAC output or comparator input.
      (#) Peripherals alternate function:
         (++) For ADC, DAC and comparators, configure the desired pin in analog 
              mode using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AN
         (++) For other peripherals (TIM, USART...):
              (+++) Connect the pin to the desired peripherals' Alternate 
                    Function (AF) using GPIO_PinAFConfig() function. For PortC, 
                    PortD and PortF, no configuration is needed.
              (+++) Configure the desired pin in alternate function mode using
                    GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
              (+++) Select the type, pull-up/pull-down and output speed via 
                    GPIO_PuPd, GPIO_OType and GPIO_Speed members
              (+++) Call GPIO_Init() function
      (#) To get the level of a pin configured in input mode use GPIO_ReadInputDataBit()
      (#) To set/reset the level of a pin configured in output mode use
          GPIO_SetBits()/GPIO_ResetBits()
      (#) During and just after reset, the alternate functions are not active and 
          the GPIO pins are configured in input floating mode (except JTAG pins).
      (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as 
          general-purpose (PC14 and PC15, respectively) when the LSE oscillator 
          is off. The LSE has priority over the GPIO function.
      (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as general-purpose 
          PD0 and PD1, respectively, when the HSE oscillator is off. The HSE has 
          priority over the GPIO function.
    @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f0xx_gpio.h"
#include "stm32f0xx_rcc.h"

/** @addtogroup STM32F0xx_StdPeriph_Driver
  * @{
  */

/** @defgroup GPIO 
  * @brief GPIO driver modules
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup GPIO_Private_Functions 
  * @{
  */

/** @defgroup GPIO_Group1 Initialization and Configuration
 *  @brief   Initialization and Configuration
 *
@verbatim
 ===============================================================================
                    ##### Initialization and Configuration #####
 ===============================================================================

@endverbatim
  * @{
  */

/**
  * @brief  Deinitializes the GPIOx peripheral registers to their default reset 
  *         values.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.    
  * @retval None
  */
void GPIO_DeInit(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  if(GPIOx == GPIOA)
  {
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, ENABLE);
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, DISABLE);
  }
  else if(GPIOx == GPIOB)
  {
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, ENABLE);
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, DISABLE);
  }
  else if(GPIOx == GPIOC)
  {
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, ENABLE);
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, DISABLE);
  }
  else if(GPIOx == GPIOD)
  {
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, ENABLE);
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, DISABLE);
  }
  else if(GPIOx == GPIOE)
  {
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, ENABLE);
    RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, DISABLE);
  }
  else
  {
    if(GPIOx == GPIOF)
    {
      RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, ENABLE);
      RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, DISABLE);
    }
  }
}

/**
  * @brief  Initializes the GPIOx peripheral according to the specified 
  *         parameters in the GPIO_InitStruct.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.   
  * @param  GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure that contains
  *         the configuration information for the specified GPIO peripheral.
  * @retval None
  */
void GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_InitStruct)
{
  uint32_t pinpos = 0x00, pos = 0x00 , currentpin = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_InitStruct->GPIO_Pin));
  assert_param(IS_GPIO_MODE(GPIO_InitStruct->GPIO_Mode));
  assert_param(IS_GPIO_PUPD(GPIO_InitStruct->GPIO_PuPd));

  /*-------------------------- Configure the port pins -----------------------*/
  /*-- GPIO Mode Configuration --*/
  for (pinpos = 0x00; pinpos < 0x10; pinpos++)
  {
    pos = ((uint32_t)0x01) << pinpos;

    /* Get the port pins position */
    currentpin = (GPIO_InitStruct->GPIO_Pin) & pos;

    if (currentpin == pos)
    {
      if ((GPIO_InitStruct->GPIO_Mode == GPIO_Mode_OUT) || (GPIO_InitStruct->GPIO_Mode == GPIO_Mode_AF))
      {
        /* Check Speed mode parameters */
        assert_param(IS_GPIO_SPEED(GPIO_InitStruct->GPIO_Speed));

        /* Speed mode configuration */
        GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (pinpos * 2));
        GPIOx->OSPEEDR |= ((uint32_t)(GPIO_InitStruct->GPIO_Speed) << (pinpos * 2));

        /* Check Output mode parameters */
        assert_param(IS_GPIO_OTYPE(GPIO_InitStruct->GPIO_OType));

        /* Output mode configuration */
        GPIOx->OTYPER &= ~((GPIO_OTYPER_OT_0) << ((uint16_t)pinpos));
        GPIOx->OTYPER |= (uint16_t)(((uint16_t)GPIO_InitStruct->GPIO_OType) << ((uint16_t)pinpos));
      }

      GPIOx->MODER  &= ~(GPIO_MODER_MODER0 << (pinpos * 2));

      GPIOx->MODER |= (((uint32_t)GPIO_InitStruct->GPIO_Mode) << (pinpos * 2));

      /* Pull-up Pull down resistor configuration */
      GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << ((uint16_t)pinpos * 2));
      GPIOx->PUPDR |= (((uint32_t)GPIO_InitStruct->GPIO_PuPd) << (pinpos * 2));
    }
  }
}

/**
  * @brief  Fills each GPIO_InitStruct member with its default value.
  * @param  GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure which will 
  *         be initialized.
  * @retval None
  */
void GPIO_StructInit(GPIO_InitTypeDef* GPIO_InitStruct)
{
  /* Reset GPIO init structure parameters values */
  GPIO_InitStruct->GPIO_Pin  = GPIO_Pin_All;
  GPIO_InitStruct->GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStruct->GPIO_Speed = GPIO_Speed_Level_2;
  GPIO_InitStruct->GPIO_OType = GPIO_OType_PP;
  GPIO_InitStruct->GPIO_PuPd = GPIO_PuPd_NOPULL;
}

/**
  * @brief  Locks GPIO Pins configuration registers.
  * @note   The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
  *         GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
  * @note   The configuration of the locked GPIO pins can no longer be modified
  *         until the next device reset.
  * @param  GPIOx: where x can be (A or B) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bit to be written.
  *          This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
  * @retval None
  */
void GPIO_PinLockConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  __IO uint32_t tmp = 0x00010000;

  /* Check the parameters */
  assert_param(IS_GPIO_LIST_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  tmp |= GPIO_Pin;
  /* Set LCKK bit */
  GPIOx->LCKR = tmp;
  /* Reset LCKK bit */
  GPIOx->LCKR =  GPIO_Pin;
  /* Set LCKK bit */
  GPIOx->LCKR = tmp;
  /* Read LCKK bit */
  tmp = GPIOx->LCKR;
  /* Read LCKK bit */
  tmp = GPIOx->LCKR;
}

/**
  * @}
  */

/** @defgroup GPIO_Group2 GPIO Read and Write
 *  @brief   GPIO Read and Write
 *
@verbatim   
 ===============================================================================
                      ##### GPIO Read and Write #####
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Reads the specified input port pin.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.   
  * @param  GPIO_Pin: specifies the port bit to read.
  * @note   This parameter can be GPIO_Pin_x where x can be:
  *         For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF.
  *         For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF.
  *         For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF.  
  * @retval The input port pin value.
  */
uint8_t GPIO_ReadInputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  uint8_t bitstatus = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));

  if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)Bit_RESET)
  {
    bitstatus = (uint8_t)Bit_SET;
  }
  else
  {
    bitstatus = (uint8_t)Bit_RESET;
  }
  return bitstatus;
}

/**
  * @brief  Reads the specified input port pin.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.   
  * @retval The input port pin value.
  */
uint16_t GPIO_ReadInputData(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  return ((uint16_t)GPIOx->IDR);
}

/**
  * @brief  Reads the specified output data port bit.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.   
  * @param  GPIO_Pin: Specifies the port bit to read.
  * @note   This parameter can be GPIO_Pin_x where x can be:
  *         For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF.
  *         For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF.
  *         For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. 
  * @retval The output port pin value.
  */
uint8_t GPIO_ReadOutputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  uint8_t bitstatus = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));

  if ((GPIOx->ODR & GPIO_Pin) != (uint32_t)Bit_RESET)
  {
    bitstatus = (uint8_t)Bit_SET;
  }
  else
  {
    bitstatus = (uint8_t)Bit_RESET;
  }
  return bitstatus;
}

/**
  * @brief  Reads the specified GPIO output data port.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.    
  * @retval GPIO output data port value.
  */
uint16_t GPIO_ReadOutputData(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  return ((uint16_t)GPIOx->ODR);
}

/**
  * @brief  Sets the selected data port bits.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.    
  * @param  GPIO_Pin: specifies the port bits to be written.
  * @note   This parameter can be GPIO_Pin_x where x can be:
  *         For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF.
  *         For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF.
  *         For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. 
  * @retval None
  */
void GPIO_SetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  GPIOx->BSRR = GPIO_Pin;
}

/**
  * @brief  Clears the selected data port bits.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.
  * @param  GPIO_Pin: specifies the port bits to be written.
  * @note   This parameter can be GPIO_Pin_x where x can be:
  *         For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF.
  *         For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF.
  *         For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. 
  * @retval None
  */
void GPIO_ResetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  GPIOx->BRR = GPIO_Pin;
}

/**
  * @brief  Sets or clears the selected data port bit.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.  
  * @param  GPIO_Pin: specifies the port bit to be written.
  * @param  BitVal: specifies the value to be written to the selected bit.
  *          This parameter can be one of the BitAction enumeration values:
  *            @arg Bit_RESET: to clear the port pin
  *            @arg Bit_SET: to set the port pin
  * @note   This parameter can be GPIO_Pin_x where x can be:
  *         For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF.
  *         For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF.
  *         For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF.
  * @retval None
  */
void GPIO_WriteBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, BitAction BitVal)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
  assert_param(IS_GPIO_BIT_ACTION(BitVal));

  if (BitVal != Bit_RESET)
  {
    GPIOx->BSRR = GPIO_Pin;
  }
  else
  {
    GPIOx->BRR = GPIO_Pin ;
  }
}

/**
  * @brief  Writes data to the specified GPIO data port.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOE is available only for STM32F072.
  * @note   GPIOD is not available for STM32F031.  
  * @param  PortVal: specifies the value to be written to the port output data register.
  * @retval None
  */
void GPIO_Write(GPIO_TypeDef* GPIOx, uint16_t PortVal)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  GPIOx->ODR = PortVal;
}

/**
  * @}
  */

/** @defgroup GPIO_Group3 GPIO Alternate functions configuration functions
 *  @brief   GPIO Alternate functions configuration functions
 *
@verbatim   
 ===============================================================================
          ##### GPIO Alternate functions configuration functions #####
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Writes data to the specified GPIO data port.
  * @param  GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral.
  * @note   GPIOC, GPIOD, GPIOE and GPIOF  are available only for STM32F072. 
  * @param  GPIO_PinSource: specifies the pin for the Alternate function.
  *          This parameter can be GPIO_PinSourcex where x can be (0..15) for GPIOA, GPIOB, GPIOD, GPIOE
  *          and (0..12) for GPIOC and (0, 2..5, 9..10) for GPIOF.    
  * @param  GPIO_AF: selects the pin to used as Alternate function.
  *          This parameter can be one of the following value:
  *            @arg GPIO_AF_0:  WKUP, EVENTOUT, TIM15, SPI1, TIM17, MCO, SWDAT, SWCLK,
  *                             TIM14, BOOT, USART1, CEC, IR_OUT, SPI2, TIM3, USART4,
  *                             CAN, USART2, CRS, TIM16, TIM1, TS 
  *            @arg GPIO_AF_1: USART2, CEC, TIM3, USART1, USART2, EVENTOUT, I2C1,
  *                            I2C2, TIM15, SPI2, USART3, TS, SPI1 
  *            @arg GPIO_AF_2: TIM2, TIM1, EVENTOUT, TIM16, TIM17, USB
  *            @arg GPIO_AF_3: TS, I2C1, TIM15, EVENTOUT 
  *            @arg GPIO_AF_4: TIM14, USART4, USART3, CRS, CAN
  *            @arg GPIO_AF_5: TIM16, TIM17, TIM15, SPI2, I2C2
  *            @arg GPIO_AF_6: EVENTOUT
  *            @arg GPIO_AF_7: COMP1 OUT, COMP2 OUT 
  * @note   The pin should already been configured in Alternate Function mode(AF)
  *         using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
  * @note   Refer to the Alternate function mapping table in the device datasheet 
  *         for the detailed mapping of the system and peripherals'alternate 
  *         function I/O pins.
  * @retval None
  */
void GPIO_PinAFConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_PinSource, uint8_t GPIO_AF)
{
  uint32_t temp = 0x00;
  uint32_t temp_2 = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN_SOURCE(GPIO_PinSource));
  assert_param(IS_GPIO_AF(GPIO_AF));

  temp = ((uint32_t)(GPIO_AF) << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4));
  GPIOx->AFR[GPIO_PinSource >> 0x03] &= ~((uint32_t)0xF << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4));
  temp_2 = GPIOx->AFR[GPIO_PinSource >> 0x03] | temp;
  GPIOx->AFR[GPIO_PinSource >> 0x03] = temp_2;
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/