test
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_gpio.c
- Revision:
- 76:aeb1df146756
- Child:
- 80:66393a7b209d
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_gpio.c Mon Jan 27 14:30:07 2014 +0000
@@ -0,0 +1,557 @@
+/**
+ ******************************************************************************
+ * @file stm32l1xx_gpio.c
+ * @author MCD Application Team
+ * @version V1.2.0
+ * @date 22-February-2013
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the GPIO peripheral:
+ * + Initialization and Configuration
+ * + GPIO Read and Write
+ * + GPIO Alternate functions configuration
+ *
+ * @verbatim
+ ===========================================================================
+ ##### How to use this driver #####
+ ===========================================================================
+ [..]
+ (#) Enable the GPIO AHB clock using RCC_AHBPeriphClockCmd()
+ (#) Configure the GPIO pin(s) using GPIO_Init()
+ Four possible configuration are available for each pin:
+ (++) Input: Floating, Pull-up, Pull-down.
+ (++) Output: Push-Pull (Pull-up, Pull-down or no Pull)
+ Open Drain (Pull-up, Pull-down or no Pull).
+ In output mode, the speed is configurable: Very Low, Low,
+ Medium or High.
+ (++) Alternate Function: Push-Pull (Pull-up, Pull-down or no Pull)
+ Open Drain (Pull-up, Pull-down or no Pull).
+ (++) Analog: required mode when a pin is to be used as ADC channel,
+ DAC output or comparator input.
+ (#) Peripherals alternate function:
+ (++) For ADC, DAC and comparators, configure the desired pin in
+ analog mode using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AN
+ (++) For other peripherals (TIM, USART...):
+ (+++) Connect the pin to the desired peripherals' Alternate
+ Function (AF) using GPIO_PinAFConfig() function.
+ (+++) Configure the desired pin in alternate function mode using
+ GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
+ (+++) Select the type, pull-up/pull-down and output speed via
+ GPIO_PuPd, GPIO_OType and GPIO_Speed members.
+ (+++) Call GPIO_Init() function.
+ (#) To get the level of a pin configured in input mode use GPIO_ReadInputDataBit()
+ (#) To set/reset the level of a pin configured in output mode use
+ GPIO_SetBits()/GPIO_ResetBits()
+ (#) During and just after reset, the alternate functions are not
+ active and the GPIO pins are configured in input floating mode
+ (except JTAG pins).
+ (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as
+ general-purpose (PC14 and PC15, respectively) when the LSE
+ oscillator is off. The LSE has priority over the GPIO function.
+ (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as
+ general-purpose PH0 and PH1, respectively, when the HSE
+ oscillator is off. The HSE has priority over the GPIO function.
+ @endverbatim
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2>
+ *
+ * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+ * You may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at:
+ *
+ * http://www.st.com/software_license_agreement_liberty_v2
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l1xx_gpio.h"
+#include "stm32l1xx_rcc.h"
+
+/** @addtogroup STM32L1xx_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup GPIO
+ * @brief GPIO driver modules
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup GPIO_Private_Functions
+ * @{
+ */
+
+/** @defgroup GPIO_Group1 Initialization and Configuration
+ * @brief Initialization and Configuration
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and Configuration #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the GPIOx peripheral registers to their default reset
+ * values.
+ * By default, The GPIO pins are configured in input floating mode
+ * (except JTAG pins).
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @retval None
+ */
+void GPIO_DeInit(GPIO_TypeDef* GPIOx)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+
+ if(GPIOx == GPIOA)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, DISABLE);
+ }
+ else if(GPIOx == GPIOB)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, DISABLE);
+ }
+ else if(GPIOx == GPIOC)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, DISABLE);
+ }
+ else if(GPIOx == GPIOD)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, DISABLE);
+ }
+ else if(GPIOx == GPIOE)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, DISABLE);
+ }
+ else if(GPIOx == GPIOF)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, DISABLE);
+ }
+ else if(GPIOx == GPIOG)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOG, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOG, DISABLE);
+ }
+ else
+ {
+ if(GPIOx == GPIOH)
+ {
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOH, ENABLE);
+ RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOH, DISABLE);
+ }
+ }
+}
+
+/**
+ * @brief Initializes the GPIOx peripheral according to the specified
+ * parameters in the GPIO_InitStruct.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure that
+ * contains the configuration information for the specified GPIO
+ * peripheral.
+
+ * @retval None
+ */
+void GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_InitStruct)
+{
+ uint32_t pinpos = 0x00, pos = 0x00 , currentpin = 0x00;
+
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GPIO_PIN(GPIO_InitStruct->GPIO_Pin));
+ assert_param(IS_GPIO_MODE(GPIO_InitStruct->GPIO_Mode));
+ assert_param(IS_GPIO_PUPD(GPIO_InitStruct->GPIO_PuPd));
+
+ /* -------------------------Configure the port pins---------------- */
+ /*-- GPIO Mode Configuration --*/
+ for (pinpos = 0x00; pinpos < 0x10; pinpos++)
+ {
+ pos = ((uint32_t)0x01) << pinpos;
+
+ /* Get the port pins position */
+ currentpin = (GPIO_InitStruct->GPIO_Pin) & pos;
+
+ if (currentpin == pos)
+ {
+ GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (pinpos * 2));
+
+ GPIOx->MODER |= (((uint32_t)GPIO_InitStruct->GPIO_Mode) << (pinpos * 2));
+
+ if ((GPIO_InitStruct->GPIO_Mode == GPIO_Mode_OUT) || (GPIO_InitStruct->GPIO_Mode == GPIO_Mode_AF))
+ {
+ /* Check Speed mode parameters */
+ assert_param(IS_GPIO_SPEED(GPIO_InitStruct->GPIO_Speed));
+
+ /* Speed mode configuration */
+ GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (pinpos * 2));
+ GPIOx->OSPEEDR |= ((uint32_t)(GPIO_InitStruct->GPIO_Speed) << (pinpos * 2));
+
+ /*Check Output mode parameters */
+ assert_param(IS_GPIO_OTYPE(GPIO_InitStruct->GPIO_OType));
+
+ /* Output mode configuration */
+ GPIOx->OTYPER &= ~((GPIO_OTYPER_OT_0) << ((uint16_t)pinpos)) ;
+ GPIOx->OTYPER |= (uint16_t)(((uint16_t)GPIO_InitStruct->GPIO_OType) << ((uint16_t)pinpos));
+ }
+
+ /* Pull-up Pull down resistor configuration */
+ GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << ((uint16_t)pinpos * 2));
+ GPIOx->PUPDR |= (((uint32_t)GPIO_InitStruct->GPIO_PuPd) << (pinpos * 2));
+ }
+ }
+}
+
+/**
+ * @brief Fills each GPIO_InitStruct member with its default value.
+ * @param GPIO_InitStruct : pointer to a GPIO_InitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void GPIO_StructInit(GPIO_InitTypeDef* GPIO_InitStruct)
+{
+ /* Reset GPIO init structure parameters values */
+ GPIO_InitStruct->GPIO_Pin = GPIO_Pin_All;
+ GPIO_InitStruct->GPIO_Mode = GPIO_Mode_IN;
+ GPIO_InitStruct->GPIO_Speed = GPIO_Speed_400KHz;
+ GPIO_InitStruct->GPIO_OType = GPIO_OType_PP;
+ GPIO_InitStruct->GPIO_PuPd = GPIO_PuPd_NOPULL;
+}
+
+/**
+ * @brief Locks GPIO Pins configuration registers.
+ * The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
+ * GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
+ * The configuration of the locked GPIO pins can no longer be modified
+ * until the next reset.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: specifies the port bit to be written.
+ * This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
+ * @retval None
+ */
+void GPIO_PinLockConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ __IO uint32_t tmp = 0x00010000;
+
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+ tmp |= GPIO_Pin;
+ /* Set LCKK bit */
+ GPIOx->LCKR = tmp;
+ /* Reset LCKK bit */
+ GPIOx->LCKR = GPIO_Pin;
+ /* Set LCKK bit */
+ GPIOx->LCKR = tmp;
+ /* Read LCKK bit*/
+ tmp = GPIOx->LCKR;
+ /* Read LCKK bit*/
+ tmp = GPIOx->LCKR;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup GPIO_Group2 GPIO Read and Write
+ * @brief GPIO Read and Write
+ *
+@verbatim
+ ===============================================================================
+ ##### GPIO Read and Write #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Reads the specified input port pin.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: specifies the port bit to read.
+ * This parameter can be GPIO_Pin_x where x can be (0..15).
+ * @retval The input port pin value.
+ */
+uint8_t GPIO_ReadInputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ uint8_t bitstatus = 0x00;
+
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
+
+ if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)Bit_RESET)
+ {
+ bitstatus = (uint8_t)Bit_SET;
+ }
+ else
+ {
+ bitstatus = (uint8_t)Bit_RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Reads the specified GPIO input data port.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @retval GPIO input data port value.
+ */
+uint16_t GPIO_ReadInputData(GPIO_TypeDef* GPIOx)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+
+ return ((uint16_t)GPIOx->IDR);
+}
+
+/**
+ * @brief Reads the specified output data port bit.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: Specifies the port bit to read.
+ * This parameter can be GPIO_Pin_x where x can be (0..15).
+ * @retval The output port pin value.
+ */
+uint8_t GPIO_ReadOutputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ uint8_t bitstatus = 0x00;
+
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
+
+ if ((GPIOx->ODR & GPIO_Pin) != (uint32_t)Bit_RESET)
+ {
+ bitstatus = (uint8_t)Bit_SET;
+ }
+ else
+ {
+ bitstatus = (uint8_t)Bit_RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Reads the specified GPIO output data port.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @retval GPIO output data port value.
+ */
+uint16_t GPIO_ReadOutputData(GPIO_TypeDef* GPIOx)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+
+ return ((uint16_t)GPIOx->ODR);
+}
+
+/**
+ * @brief Sets the selected data port bits.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: specifies the port bits to be written.
+ * This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
+ * @note This functions uses GPIOx_BSRR register to allow atomic read/modify
+ * accesses. In this way, there is no risk of an IRQ occurring between
+ * the read and the modify access.
+ * @retval None
+ */
+void GPIO_SetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+ GPIOx->BSRRL = GPIO_Pin;
+}
+
+/**
+ * @brief Clears the selected data port bits.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: specifies the port bits to be written.
+ * This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
+ * @note This functions uses GPIOx_BSRR register to allow atomic read/modify
+ * accesses. In this way, there is no risk of an IRQ occurring between
+ * the read and the modify access.
+ * @retval None
+ */
+void GPIO_ResetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GPIO_PIN(GPIO_Pin));
+
+ GPIOx->BSRRH = GPIO_Pin;
+}
+
+/**
+ * @brief Sets or clears the selected data port bit.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: specifies the port bit to be written.
+ * This parameter can be one of GPIO_Pin_x where x can be (0..15).
+ * @param BitVal: specifies the value to be written to the selected bit.
+ * This parameter can be one of the BitAction enum values:
+ * @arg Bit_RESET: to clear the port pin
+ * @arg Bit_SET: to set the port pin
+ * @retval None
+ */
+void GPIO_WriteBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, BitAction BitVal)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
+ assert_param(IS_GPIO_BIT_ACTION(BitVal));
+
+ if (BitVal != Bit_RESET)
+ {
+ GPIOx->BSRRL = GPIO_Pin;
+ }
+ else
+ {
+ GPIOx->BSRRH = GPIO_Pin ;
+ }
+}
+
+/**
+ * @brief Writes data to the specified GPIO data port.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param PortVal: specifies the value to be written to the port output data
+ * register.
+ * @retval None
+ */
+void GPIO_Write(GPIO_TypeDef* GPIOx, uint16_t PortVal)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+
+ GPIOx->ODR = PortVal;
+}
+
+/**
+ * @brief Toggles the specified GPIO pins..
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_Pin: Specifies the pins to be toggled.
+ * @retval None
+ */
+void GPIO_ToggleBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
+{
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+
+ GPIOx->ODR ^= GPIO_Pin;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup GPIO_Group3 GPIO Alternate functions configuration functions
+ * @brief GPIO Alternate functions configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### GPIO Alternate functions configuration functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Changes the mapping of the specified pin.
+ * @param GPIOx: where x can be (A..H) to select the GPIO peripheral.
+ * @param GPIO_PinSource: specifies the pin for the Alternate function.
+ * This parameter can be GPIO_PinSourcex where x can be (0..15).
+ * @param GPIO_AFSelection: selects the pin to used as Alternat function.
+ * This parameter can be one of the following values:
+ * @arg GPIO_AF_RTC_50Hz: RTC 50/60 Hz synchronization
+ * @arg GPIO_AF_MCO: Microcontroller clock output
+ * @arg GPIO_AF_RTC_AF1: Time stamp, Tamper, Alarm A out, Alarm B out,
+ * 512 Hz clock output (with an LSE oscillator of 32.768 kHz)
+ * @arg GPIO_AF_WKUP: wakeup
+ * @arg GPIO_AF_SWJ: SWJ (SW and JTAG)
+ * @arg GPIO_AF_TRACE: Connect TRACE pins to AF0 (default after reset)
+ * @arg GPIO_AF_TIM2c: Connect TIM2 pins to AF1
+ * @arg GPIO_AF_TIM3: Connect TIM3 pins to AF2
+ * @arg GPIO_AF_TIM4: Connect TIM4 pins to AF2
+ * @arg GPIO_AF_TIM5: Connect TIM5 pins to AF2
+ * @arg GPIO_AF_TIM9: Connect TIM9 pins to AF3
+ * @arg GPIO_AF_TIM10: Connect TIM10 pins to AF3
+ * @arg GPIO_AF_TIM11: Connect TIM11 pins to AF3
+ * @arg GPIO_AF_I2C1: Connect I2C1 pins to AF4
+ * @arg GPIO_AF_I2C2: Connect I2C2 pins to AF4
+ * @arg GPIO_AF_SPI1: Connect SPI1 pins to AF5
+ * @arg GPIO_AF_SPI2: Connect SPI2/I2S2 pins to AF5
+ * @arg GPIO_AF_SPI3: Connect SPI3/I2S3 pins to AF6
+ * @arg GPIO_AF_USART1: Connect USART1 pins to AF7
+ * @arg GPIO_AF_USART2: Connect USART2 pins to AF7
+ * @arg GPIO_AF_USART3: Connect USART3 pins to AF7
+ * @arg GPIO_AF_UART4: Connect UART4 pins to AF8
+ * @arg GPIO_AF_UART5: Connect UART5 pins to AF8
+ * @arg GPIO_AF_USB: Connect USB pins to AF10
+ * @arg GPIO_AF_LCD: Connect LCD pins to AF11
+ * @arg GPIO_AF_FSMC: Connect FSMC pins to AF12
+ * @arg GPIO_AF_SDIO: Connect SDIO pins to AF12
+ * @arg GPIO_AF_RI: Connect RI pins to AF14
+ * @arg GPIO_AF_EVENTOUT: Cortex-M3 EVENTOUT signal
+ * @note The pin should already been configured in Alternate Function mode(AF)
+ * using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
+ * @note Please refer to the Alternate function mapping table in the device
+ * datasheet for the detailed mapping of the system and peripherals'
+ * alternate function I/O pins.
+ * @note EVENTOUT is not mapped on PH0, PH1 and PH2.
+ * @retval None
+ */
+void GPIO_PinAFConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_PinSource, uint8_t GPIO_AF)
+{
+ uint32_t temp = 0x00;
+ uint32_t temp_2 = 0x00;
+
+ /* Check the parameters */
+ assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
+ assert_param(IS_GPIO_PIN_SOURCE(GPIO_PinSource));
+ assert_param(IS_GPIO_AF(GPIO_AF));
+
+ temp = ((uint32_t)(GPIO_AF) << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)) ;
+ GPIOx->AFR[GPIO_PinSource >> 0x03] &= ~((uint32_t)0xF << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)) ;
+ temp_2 = GPIOx->AFR[GPIO_PinSource >> 0x03] | temp;
+ GPIOx->AFR[GPIO_PinSource >> 0x03] = temp_2;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/