test
mbed library sources
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F302R8/stm32f30x_tim.c
- Revision:
- 125:23cc3068a9e4
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F302R8/stm32f30x_tim.c Wed Mar 19 10:15:22 2014 +0000
@@ -0,0 +1,4005 @@
+/**
+ ******************************************************************************
+ * @file stm32f30x_tim.c
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 27-February-2014
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the TIM peripheral:
+ * + TimeBase management
+ * + Output Compare management
+ * + Input Capture management
+ * + Advanced-control timers (TIM1 and TIM8) specific features
+ * + Interrupts, DMA and flags management
+ * + Clocks management
+ * + Synchronization management
+ * + Specific interface management
+ * + Specific remapping management
+ *
+ @verbatim
+
+ ==============================================================================
+ ##### How to use this driver #####
+ ==============================================================================
+ [..] This driver provides functions to configure and program the TIM
+ of all stm32f30x devices.
+ These functions are split in 9 groups:
+
+ (#) TIM TimeBase management: this group includes all needed functions
+ to configure the TM Timebase unit:
+ (++) Set/Get Prescaler
+ (++) Set/Get Autoreload
+ (++) Counter modes configuration
+ (++) Set Clock division
+ (++) Select the One Pulse mode
+ (++) Update Request Configuration
+ (++) Update Disable Configuration
+ (++) Auto-Preload Configuration
+ (++) Enable/Disable the counter
+
+ (#) TIM Output Compare management: this group includes all needed
+ functions to configure the Capture/Compare unit used in Output
+ compare mode:
+ (++) Configure each channel, independently, in Output Compare mode
+ (++) Select the output compare modes
+ (++) Select the Polarities of each channel
+ (++) Set/Get the Capture/Compare register values
+ (++) Select the Output Compare Fast mode
+ (++) Select the Output Compare Forced mode
+ (++) Output Compare-Preload Configuration
+ (++) Clear Output Compare Reference
+ (++) Select the OCREF Clear signal
+ (++) Enable/Disable the Capture/Compare Channels
+
+ (#) TIM Input Capture management: this group includes all needed
+ functions to configure the Capture/Compare unit used in
+ Input Capture mode:
+ (++) Configure each channel in input capture mode
+ (++) Configure Channel1/2 in PWM Input mode
+ (++) Set the Input Capture Prescaler
+ (++) Get the Capture/Compare values
+
+ (#) Advanced-control timers (TIM1 and TIM8) specific features
+ (++) Configures the Break input, dead time, Lock level, the OSSI,
+ the OSSR State and the AOE(automatic output enable)
+ (++) Enable/Disable the TIM peripheral Main Outputs
+ (++) Select the Commutation event
+ (++) Set/Reset the Capture Compare Preload Control bit
+
+ (#) TIM interrupts, DMA and flags management
+ (++) Enable/Disable interrupt sources
+ (++) Get flags status
+ (++) Clear flags/ Pending bits
+ (++) Enable/Disable DMA requests
+ (++) Configure DMA burst mode
+ (++) Select CaptureCompare DMA request
+
+ (#) TIM clocks management: this group includes all needed functions
+ to configure the clock controller unit:
+ (++) Select internal/External clock
+ (++) Select the external clock mode: ETR(Mode1/Mode2), TIx or ITRx
+
+ (#) TIM synchronization management: this group includes all needed
+ functions to configure the Synchronization unit:
+ (++) Select Input Trigger
+ (++) Select Output Trigger
+ (++) Select Master Slave Mode
+ (++) ETR Configuration when used as external trigger
+
+ (#) TIM specific interface management, this group includes all
+ needed functions to use the specific TIM interface:
+ (++) Encoder Interface Configuration
+ (++) Select Hall Sensor
+
+ (#) TIM specific remapping management includes the Remapping
+ configuration of specific timers
+
+ @endverbatim
+
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f30x_tim.h"
+#include "stm32f30x_rcc.h"
+
+/** @addtogroup STM32F30x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup TIM
+ * @brief TIM driver modules
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+
+/* ---------------------- TIM registers bit mask ------------------------ */
+#define SMCR_ETR_MASK ((uint16_t)0x00FF)
+#define CCMR_OFFSET ((uint16_t)0x0018)
+#define CCER_CCE_SET ((uint16_t)0x0001)
+#define CCER_CCNE_SET ((uint16_t)0x0004)
+#define CCMR_OC13M_MASK ((uint32_t)0xFFFEFF8F)
+#define CCMR_OC24M_MASK ((uint32_t)0xFEFF8FFF)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+static void TI1_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI2_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI3_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI4_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup TIM_Private_Functions
+ * @{
+ */
+
+/** @defgroup TIM_Group1 TimeBase management functions
+ * @brief TimeBase management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### TimeBase management functions #####
+ ===============================================================================
+
+
+ *** TIM Driver: how to use it in Timing(Time base) Mode ***
+ ============================================================
+ [..]
+ To use the Timer in Timing(Time base) mode, the following steps are mandatory:
+
+ (#) Enable TIM clock using
+ RCC_APBxPeriphClockCmd(RCC_APBxPeriph_TIMx, ENABLE) function
+ (#) Fill the TIM_TimeBaseInitStruct with the desired parameters.
+ (#) Call TIM_TimeBaseInit(TIMx, &TIM_TimeBaseInitStruct) to configure
+ the Time Base unit
+ with the corresponding configuration
+ (#) Enable the NVIC if you need to generate the update interrupt.
+ (#) Enable the corresponding interrupt using the function
+ TIM_ITConfig(TIMx, TIM_IT_Update)
+ (#) Call the TIM_Cmd(ENABLE) function to enable the TIM counter.
+ [..]
+ (@) All other functions can be used separately to modify, if needed,
+ a specific feature of the Timer.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the TIMx peripheral registers to their default reset values.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @retval None
+
+ */
+void TIM_DeInit(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ if (TIMx == TIM1)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM1, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM1, DISABLE);
+ }
+ else if (TIMx == TIM2)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM2, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM2, DISABLE);
+ }
+ else if (TIMx == TIM3)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM3, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM3, DISABLE);
+ }
+ else if (TIMx == TIM4)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM4, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM4, DISABLE);
+ }
+ else if (TIMx == TIM6)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM6, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM6, DISABLE);
+ }
+ else if (TIMx == TIM7)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM7, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM7, DISABLE);
+ }
+ else if (TIMx == TIM8)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM8, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM8, DISABLE);
+ }
+ else if (TIMx == TIM15)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM15, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM15, DISABLE);
+ }
+ else if (TIMx == TIM16)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM16, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM16, DISABLE);
+ }
+ else
+ {
+ if (TIMx == TIM17)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM17, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM17, DISABLE);
+ }
+ }
+}
+
+/**
+ * @brief Initializes the TIMx Time Base Unit peripheral according to
+ * the specified parameters in the TIM_TimeBaseInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_TimeBaseInitStruct: pointer to a TIM_TimeBaseInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_TimeBaseInit(TIM_TypeDef* TIMx, TIM_TimeBaseInitTypeDef* TIM_TimeBaseInitStruct)
+{
+ uint16_t tmpcr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_COUNTER_MODE(TIM_TimeBaseInitStruct->TIM_CounterMode));
+ assert_param(IS_TIM_CKD_DIV(TIM_TimeBaseInitStruct->TIM_ClockDivision));
+
+ tmpcr1 = TIMx->CR1;
+
+ if((TIMx == TIM1) || (TIMx == TIM8)|| (TIMx == TIM2) ||
+ (TIMx == TIM3)|| (TIMx == TIM4))
+ {
+ /* Select the Counter Mode */
+ tmpcr1 &= (uint16_t)(~(TIM_CR1_DIR | TIM_CR1_CMS));
+ tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->TIM_CounterMode;
+ }
+
+ if((TIMx != TIM6) && (TIMx != TIM7))
+ {
+ /* Set the clock division */
+ tmpcr1 &= (uint16_t)(~TIM_CR1_CKD);
+ tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->TIM_ClockDivision;
+ }
+
+ TIMx->CR1 = tmpcr1;
+
+ /* Set the Autoreload value */
+ TIMx->ARR = TIM_TimeBaseInitStruct->TIM_Period ;
+
+ /* Set the Prescaler value */
+ TIMx->PSC = TIM_TimeBaseInitStruct->TIM_Prescaler;
+
+ if ((TIMx == TIM1) || (TIMx == TIM8)|| (TIMx == TIM15) ||
+ (TIMx == TIM16) || (TIMx == TIM17))
+ {
+ /* Set the Repetition Counter value */
+ TIMx->RCR = TIM_TimeBaseInitStruct->TIM_RepetitionCounter;
+ }
+
+ /* Generate an update event to reload the Prescaler
+ and the repetition counter(only for TIM1 and TIM8) value immediatly */
+ TIMx->EGR = TIM_PSCReloadMode_Immediate;
+}
+
+/**
+ * @brief Fills each TIM_TimeBaseInitStruct member with its default value.
+ * @param TIM_TimeBaseInitStruct : pointer to a TIM_TimeBaseInitTypeDef
+ * structure which will be initialized.
+ * @retval None
+ */
+void TIM_TimeBaseStructInit(TIM_TimeBaseInitTypeDef* TIM_TimeBaseInitStruct)
+{
+ /* Set the default configuration */
+ TIM_TimeBaseInitStruct->TIM_Period = 0xFFFFFFFF;
+ TIM_TimeBaseInitStruct->TIM_Prescaler = 0x0000;
+ TIM_TimeBaseInitStruct->TIM_ClockDivision = TIM_CKD_DIV1;
+ TIM_TimeBaseInitStruct->TIM_CounterMode = TIM_CounterMode_Up;
+ TIM_TimeBaseInitStruct->TIM_RepetitionCounter = 0x0000;
+}
+
+/**
+ * @brief Configures the TIMx Prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param Prescaler: specifies the Prescaler Register value
+ * @param TIM_PSCReloadMode: specifies the TIM Prescaler Reload mode
+ * This parameter can be one of the following values:
+ * @arg TIM_PSCReloadMode_Update: The Prescaler is loaded at the update event.
+ * @arg TIM_PSCReloadMode_Immediate: The Prescaler is loaded immediatly.
+ * @retval None
+ */
+void TIM_PrescalerConfig(TIM_TypeDef* TIMx, uint16_t Prescaler, uint16_t TIM_PSCReloadMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_PRESCALER_RELOAD(TIM_PSCReloadMode));
+ /* Set the Prescaler value */
+ TIMx->PSC = Prescaler;
+ /* Set or reset the UG Bit */
+ TIMx->EGR = TIM_PSCReloadMode;
+}
+
+/**
+ * @brief Specifies the TIMx Counter Mode to be used.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_CounterMode: specifies the Counter Mode to be used
+ * This parameter can be one of the following values:
+ * @arg TIM_CounterMode_Up: TIM Up Counting Mode
+ * @arg TIM_CounterMode_Down: TIM Down Counting Mode
+ * @arg TIM_CounterMode_CenterAligned1: TIM Center Aligned Mode1
+ * @arg TIM_CounterMode_CenterAligned2: TIM Center Aligned Mode2
+ * @arg TIM_CounterMode_CenterAligned3: TIM Center Aligned Mode3
+ * @retval None
+ */
+void TIM_CounterModeConfig(TIM_TypeDef* TIMx, uint16_t TIM_CounterMode)
+{
+ uint16_t tmpcr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_COUNTER_MODE(TIM_CounterMode));
+
+ tmpcr1 = TIMx->CR1;
+
+ /* Reset the CMS and DIR Bits */
+ tmpcr1 &= (uint16_t)~(TIM_CR1_DIR | TIM_CR1_CMS);
+
+ /* Set the Counter Mode */
+ tmpcr1 |= TIM_CounterMode;
+
+ /* Write to TIMx CR1 register */
+ TIMx->CR1 = tmpcr1;
+}
+
+/**
+ * @brief Sets the TIMx Counter Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param Counter: specifies the Counter register new value.
+ * @retval None
+ */
+void TIM_SetCounter(TIM_TypeDef* TIMx, uint32_t Counter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Set the Counter Register value */
+ TIMx->CNT = Counter;
+}
+
+/**
+ * @brief Sets the TIMx Autoreload Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param Autoreload: specifies the Autoreload register new value.
+ * @retval None
+ */
+void TIM_SetAutoreload(TIM_TypeDef* TIMx, uint32_t Autoreload)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Set the Autoreload Register value */
+ TIMx->ARR = Autoreload;
+}
+
+/**
+ * @brief Gets the TIMx Counter value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @retval Counter Register value
+ */
+uint32_t TIM_GetCounter(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Get the Counter Register value */
+ return TIMx->CNT;
+}
+
+/**
+ * @brief Gets the TIMx Prescaler value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @retval Prescaler Register value.
+ */
+uint16_t TIM_GetPrescaler(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Get the Prescaler Register value */
+ return TIMx->PSC;
+}
+
+/**
+ * @brief Enables or Disables the TIMx Update event.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param NewState: new state of the TIMx UDIS bit
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_UpdateDisableConfig(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the Update Disable Bit */
+ TIMx->CR1 |= TIM_CR1_UDIS;
+ }
+ else
+ {
+ /* Reset the Update Disable Bit */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_UDIS;
+ }
+}
+
+/**
+ * @brief Configures the TIMx Update Request Interrupt source.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_UpdateSource: specifies the Update source.
+ * This parameter can be one of the following values:
+ * @arg TIM_UpdateSource_Regular: Source of update is the counter
+ * overflow/underflow or the setting of UG bit, or an update
+ * generation through the slave mode controller.
+ * @arg TIM_UpdateSource_Global: Source of update is counter overflow/underflow.
+ * @retval None
+ */
+void TIM_UpdateRequestConfig(TIM_TypeDef* TIMx, uint16_t TIM_UpdateSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_UPDATE_SOURCE(TIM_UpdateSource));
+
+ if (TIM_UpdateSource != TIM_UpdateSource_Global)
+ {
+ /* Set the URS Bit */
+ TIMx->CR1 |= TIM_CR1_URS;
+ }
+ else
+ {
+ /* Reset the URS Bit */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_URS;
+ }
+}
+
+/**
+ * @brief Sets or resets the update interrupt flag (UIF)status bit Remapping.
+ * when sets, reading TIMx_CNT register returns UIF bit instead of CNT[31]
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param NewState: new state of the UIFREMAP bit.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_UIFRemap(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the TIM Counter */
+ TIMx->CR1 |= TIM_CR1_UIFREMAP;
+ }
+ else
+ {
+ /* Disable the TIM Counter */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_UIFREMAP;
+ }
+}
+
+/**
+ * @brief Enables or disables TIMx peripheral Preload register on ARR.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param NewState: new state of the TIMx peripheral Preload register
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_ARRPreloadConfig(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the ARR Preload Bit */
+ TIMx->CR1 |= TIM_CR1_ARPE;
+ }
+ else
+ {
+ /* Reset the ARR Preload Bit */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_ARPE;
+ }
+}
+
+/**
+ * @brief Selects the TIMx's One Pulse Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6 ,7 ,8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OPMode: specifies the OPM Mode to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_OPMode_Single
+ * @arg TIM_OPMode_Repetitive
+ * @retval None
+ */
+void TIM_SelectOnePulseMode(TIM_TypeDef* TIMx, uint16_t TIM_OPMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_OPM_MODE(TIM_OPMode));
+
+ /* Reset the OPM Bit */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_OPM;
+
+ /* Configure the OPM Mode */
+ TIMx->CR1 |= TIM_OPMode;
+}
+
+/**
+ * @brief Sets the TIMx Clock Division value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17, to select the TIM peripheral.
+ * @param TIM_CKD: specifies the clock division value.
+ * This parameter can be one of the following value:
+ * @arg TIM_CKD_DIV1: TDTS = Tck_tim
+ * @arg TIM_CKD_DIV2: TDTS = 2*Tck_tim
+ * @arg TIM_CKD_DIV4: TDTS = 4*Tck_tim
+ * @retval None
+ */
+void TIM_SetClockDivision(TIM_TypeDef* TIMx, uint16_t TIM_CKD)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_CKD_DIV(TIM_CKD));
+
+ /* Reset the CKD Bits */
+ TIMx->CR1 &= (uint16_t)(~TIM_CR1_CKD);
+
+ /* Set the CKD value */
+ TIMx->CR1 |= TIM_CKD;
+}
+
+/**
+ * @brief Enables or disables the specified TIM peripheral.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select
+ * the TIMx peripheral.
+ * @param NewState: new state of the TIMx peripheral.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_Cmd(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the TIM Counter */
+ TIMx->CR1 |= TIM_CR1_CEN;
+ }
+ else
+ {
+ /* Disable the TIM Counter */
+ TIMx->CR1 &= (uint16_t)~TIM_CR1_CEN;
+ }
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group2 Output Compare management functions
+ * @brief Output Compare management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Output Compare management functions #####
+ ===============================================================================
+
+ *** TIM Driver: how to use it in Output Compare Mode ***
+ ========================================================
+ [..]
+ To use the Timer in Output Compare mode, the following steps are mandatory:
+
+ (#) Enable TIM clock using RCC_APBxPeriphClockCmd(RCC_APBxPeriph_TIMx, ENABLE) function
+
+ (#) Configure the TIM pins by configuring the corresponding GPIO pins
+
+ (#) Configure the Time base unit as described in the first part of this driver,
+ if needed, else the Timer will run with the default configuration:
+ (++) Autoreload value = 0xFFFF
+ (++) Prescaler value = 0x0000
+ (++) Counter mode = Up counting
+ (++) Clock Division = TIM_CKD_DIV1
+ (#) Fill the TIM_OCInitStruct with the desired parameters including:
+ (++) The TIM Output Compare mode: TIM_OCMode
+ (++) TIM Output State: TIM_OutputState
+ (++) TIM Pulse value: TIM_Pulse
+ (++) TIM Output Compare Polarity : TIM_OCPolarity
+
+ (#) Call TIM_OCxInit(TIMx, &TIM_OCInitStruct) to configure the desired channel with the
+ corresponding configuration
+
+ (#) Call the TIM_Cmd(ENABLE) function to enable the TIM counter.
+ [..]
+ (@) All other functions can be used separately to modify, if needed,
+ a specific feature of the Timer.
+
+ (@) In case of PWM mode, this function is mandatory:
+ TIM_OCxPreloadConfig(TIMx, TIM_OCPreload_ENABLE);
+
+ (@) If the corresponding interrupt or DMA request are needed, the user should:
+ (#@) Enable the NVIC (or the DMA) to use the TIM interrupts (or DMA requests).
+ (#@) Enable the corresponding interrupt (or DMA request) using the function
+ TIM_ITConfig(TIMx, TIM_IT_CCx) (or TIM_DMA_Cmd(TIMx, TIM_DMA_CCx))
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initializes the TIMx Channel1 according to the specified parameters in
+ * the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17, to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC1Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 1: Reset the CC1E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC1E;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmrx = TIMx->CCMR1;
+
+ /* Reset the Output Compare Mode Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR1_OC1M;
+ tmpccmrx &= (uint32_t)~TIM_CCMR1_CC1S;
+ /* Select the Output Compare Mode */
+ tmpccmrx |= TIM_OCInitStruct->TIM_OCMode;
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC1P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= TIM_OCInitStruct->TIM_OCPolarity;
+
+ /* Set the Output State */
+ tmpccer |= TIM_OCInitStruct->TIM_OutputState;
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM15) || (TIMx == TIM16) || (TIMx == TIM17))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC1NP;
+ /* Set the Output N Polarity */
+ tmpccer |= TIM_OCInitStruct->TIM_OCNPolarity;
+ /* Reset the Output N State */
+ tmpccer &= (uint32_t)~TIM_CCER_CC1NE;
+
+ /* Set the Output N State */
+ tmpccer |= TIM_OCInitStruct->TIM_OutputNState;
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS1;
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS1N;
+ /* Set the Output Idle state */
+ tmpcr2 |= TIM_OCInitStruct->TIM_OCIdleState;
+ /* Set the Output N Idle state */
+ tmpcr2 |= TIM_OCInitStruct->TIM_OCNIdleState;
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR1 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel2 according to the specified parameters
+ * in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC2Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 2: Reset the CC2E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC2E;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmrx = TIMx->CCMR1;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR1_OC2M;
+ tmpccmrx &= (uint32_t)~TIM_CCMR1_CC2S;
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint32_t)(TIM_OCInitStruct->TIM_OCMode << 8);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC2P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCPolarity << 4);
+
+ /* Set the Output State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputState << 4);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC2NP;
+ /* Set the Output N Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCNPolarity << 4);
+ /* Reset the Output N State */
+ tmpccer &= (uint32_t)~TIM_CCER_CC2NE;
+
+ /* Set the Output N State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputNState << 4);
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS2;
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS2N;
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCIdleState << 2);
+ /* Set the Output N Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCNIdleState << 2);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR2 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel3 according to the specified parameters
+ * in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC3Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 3: Reset the CC2E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC3E;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmrx = TIMx->CCMR2;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR2_OC3M;
+ tmpccmrx &= (uint32_t)~TIM_CCMR2_CC3S;
+ /* Select the Output Compare Mode */
+ tmpccmrx |= TIM_OCInitStruct->TIM_OCMode;
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC3P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCPolarity << 8);
+
+ /* Set the Output State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputState << 8);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC3NP;
+ /* Set the Output N Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCNPolarity << 8);
+ /* Reset the Output N State */
+ tmpccer &= (uint32_t)~TIM_CCER_CC3NE;
+
+ /* Set the Output N State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputNState << 8);
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS3;
+ tmpcr2 &= (uint32_t)~TIM_CR2_OIS3N;
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCIdleState << 4);
+ /* Set the Output N Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCNIdleState << 4);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR3 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel4 according to the specified parameters
+ * in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC4Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 4: Reset the CC4E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC4E;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmrx = TIMx->CCMR2;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR2_OC4M;
+ tmpccmrx &= (uint32_t)~TIM_CCMR2_CC4S;
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint32_t)(TIM_OCInitStruct->TIM_OCMode << 8);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC4P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCPolarity << 12);
+
+ /* Set the Output State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputState << 12);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+ /* Reset the Output Compare IDLE State */
+ tmpcr2 &=(uint32_t) ~TIM_CR2_OIS4;
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCIdleState << 6);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR4 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel5 according to the specified parameters
+ * in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC5Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 5: Reset the CC5E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC5E; /* to be verified*/
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR3 register value */
+ tmpccmrx = TIMx->CCMR3;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR3_OC5M;
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint32_t)(TIM_OCInitStruct->TIM_OCMode);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC5P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCPolarity << 16);
+
+ /* Set the Output State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputState << 16);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+ /* Reset the Output Compare IDLE State */
+ tmpcr2 &=(uint32_t) ~TIM_CR2_OIS5;
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCIdleState << 16);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR3 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR5 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel6 according to the specified parameters
+ * in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC6Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint32_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+
+ /* Disable the Channel 5: Reset the CC5E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC6E; /* to be verified*/
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR3 register value */
+ tmpccmrx = TIMx->CCMR3;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint32_t)~TIM_CCMR3_OC6M;
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint32_t)(TIM_OCInitStruct->TIM_OCMode << 8);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint32_t)~TIM_CCER_CC6P;
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OCPolarity << 20);
+
+ /* Set the Output State */
+ tmpccer |= (uint32_t)((uint32_t)TIM_OCInitStruct->TIM_OutputState << 20);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+ /* Reset the Output Compare IDLE State */
+ tmpcr2 &=(uint32_t) ~TIM_CR2_OIS6;
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCIdleState << 18);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR3 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR6 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Selects the TIM Group Channel 5 and Channel 1,
+ OC1REFC is the logical AND of OC1REFC and OC5REF.
+ * @param TIMx: where x can be 1 or 8 to select the TIMx peripheral
+ * @param NewState: new state of the Commutation event.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectGC5C1(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the GC5C1 Bit */
+ TIMx->CCR5 |= TIM_CCR5_GC5C1;
+ }
+ else
+ {
+ /* Reset the GC5C1 Bit */
+ TIMx->CCR5 &= (uint32_t)~TIM_CCR5_GC5C1;
+ }
+}
+
+/**
+ * @brief Selects the TIM Group Channel 5 and Channel 2,
+ OC2REFC is the logical AND of OC2REFC and OC5REF.
+ * @param TIMx: where x can be 1 or 8 to select the TIMx peripheral
+ * @param NewState: new state of the Commutation event.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectGC5C2(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the GC5C2 Bit */
+ TIMx->CCR5 |= TIM_CCR5_GC5C2;
+ }
+ else
+ {
+ /* Reset the GC5C2 Bit */
+ TIMx->CCR5 &= (uint32_t)~TIM_CCR5_GC5C2;
+ }
+}
+
+
+/**
+ * @brief Selects the TIM Group Channel 5 and Channel 3,
+ OC3REFC is the logical AND of OC3REFC and OC5REF.
+ * @param TIMx: where x can be 1 or 8 to select the TIMx peripheral
+ * @param NewState: new state of the Commutation event.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectGC5C3(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the GC5C3 Bit */
+ TIMx->CCR5 |= TIM_CCR5_GC5C3;
+ }
+ else
+ {
+ /* Reset the GC5C3 Bit */
+ TIMx->CCR5 &= (uint32_t)~TIM_CCR5_GC5C3;
+ }
+}
+
+/**
+ * @brief Fills each TIM_OCInitStruct member with its default value.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void TIM_OCStructInit(TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ /* Set the default configuration */
+ TIM_OCInitStruct->TIM_OCMode = TIM_OCMode_Timing;
+ TIM_OCInitStruct->TIM_OutputState = TIM_OutputState_Disable;
+ TIM_OCInitStruct->TIM_OutputNState = TIM_OutputNState_Disable;
+ TIM_OCInitStruct->TIM_Pulse = 0x00000000;
+ TIM_OCInitStruct->TIM_OCPolarity = TIM_OCPolarity_High;
+ TIM_OCInitStruct->TIM_OCNPolarity = TIM_OCPolarity_High;
+ TIM_OCInitStruct->TIM_OCIdleState = TIM_OCIdleState_Reset;
+ TIM_OCInitStruct->TIM_OCNIdleState = TIM_OCNIdleState_Reset;
+}
+
+/**
+ * @brief Selects the TIM Output Compare Mode.
+ * @note This function disables the selected channel before changing the Output
+ * Compare Mode. If needed, user has to enable this channel using
+ * TIM_CCxCmd() and TIM_CCxNCmd() functions.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @arg TIM_Channel_4: TIM Channel 4
+ * @param TIM_OCMode: specifies the TIM Output Compare Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCMode_Timing
+ * @arg TIM_OCMode_Active
+ * @arg TIM_OCMode_Toggle
+ * @arg TIM_OCMode_PWM1
+ * @arg TIM_OCMode_PWM2
+ * @arg TIM_ForcedAction_Active
+ * @arg TIM_ForcedAction_InActive
+ * @arg TIM_OCMode_Retrigerrable_OPM1
+ * @arg TIM_OCMode_Retrigerrable_OPM2
+ * @arg TIM_OCMode_Combined_PWM1
+ * @arg TIM_OCMode_Combined_PWM2
+ * @arg TIM_OCMode_Asymmetric_PWM1
+ * @arg TIM_OCMode_Asymmetric_PWM2
+ * @retval None
+ */
+void TIM_SelectOCxM(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint32_t TIM_OCMode)
+{
+ uint32_t tmp = 0;
+ uint16_t tmp1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_OCM(TIM_OCMode));
+
+ tmp = (uint32_t) TIMx;
+ tmp += CCMR_OFFSET;
+
+ tmp1 = CCER_CCE_SET << (uint16_t)TIM_Channel;
+
+ /* Disable the Channel: Reset the CCxE Bit */
+ TIMx->CCER &= (uint16_t) ~tmp1;
+
+ if((TIM_Channel == TIM_Channel_1) ||(TIM_Channel == TIM_Channel_3))
+ {
+ tmp += (TIM_Channel>>1);
+
+ /* Reset the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp &= CCMR_OC13M_MASK;
+
+ /* Configure the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp |= TIM_OCMode;
+ }
+ else
+ {
+ tmp += (uint32_t)(TIM_Channel - (uint32_t)4)>> (uint32_t)1;
+
+ /* Reset the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp &= CCMR_OC24M_MASK;
+
+ /* Configure the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp |= (uint32_t)(TIM_OCMode << 8);
+ }
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare1 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param Compare1: specifies the Capture Compare1 register new value.
+ * @retval None
+ */
+void TIM_SetCompare1(TIM_TypeDef* TIMx, uint32_t Compare1)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+
+ /* Set the Capture Compare1 Register value */
+ TIMx->CCR1 = Compare1;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare2 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param Compare2: specifies the Capture Compare2 register new value.
+ * @retval None
+ */
+void TIM_SetCompare2(TIM_TypeDef* TIMx, uint32_t Compare2)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+
+ /* Set the Capture Compare2 Register value */
+ TIMx->CCR2 = Compare2;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare3 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param Compare3: specifies the Capture Compare3 register new value.
+ * @retval None
+ */
+void TIM_SetCompare3(TIM_TypeDef* TIMx, uint32_t Compare3)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+
+ /* Set the Capture Compare3 Register value */
+ TIMx->CCR3 = Compare3;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare4 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param Compare4: specifies the Capture Compare4 register new value.
+ * @retval None
+ */
+void TIM_SetCompare4(TIM_TypeDef* TIMx, uint32_t Compare4)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+
+ /* Set the Capture Compare4 Register value */
+ TIMx->CCR4 = Compare4;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare5 Register value
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param Compare5: specifies the Capture Compare5 register new value.
+ * @retval None
+ */
+void TIM_SetCompare5(TIM_TypeDef* TIMx, uint32_t Compare5)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+
+ /* Set the Capture Compare5 Register value */
+ TIMx->CCR5 = Compare5;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare6 Register value
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param Compare6: specifies the Capture Compare5 register new value.
+ * @retval None
+ */
+void TIM_SetCompare6(TIM_TypeDef* TIMx, uint32_t Compare6)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+
+ /* Set the Capture Compare6 Register value */
+ TIMx->CCR6 = Compare6;
+}
+
+/**
+ * @brief Forces the TIMx output 1 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC1REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC1REF.
+ * @retval None
+ */
+void TIM_ForcedOC1Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC1M Bits */
+ tmpccmr1 &= (uint32_t)~TIM_CCMR1_OC1M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr1 |= TIM_ForcedAction;
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Forces the TIMx output 2 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC2REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC2REF.
+ * @retval None
+ */
+void TIM_ForcedOC2Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC2M Bits */
+ tmpccmr1 &= (uint32_t)~TIM_CCMR1_OC2M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr1 |= ((uint32_t)TIM_ForcedAction << 8);
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Forces the TIMx output 3 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC3REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC3REF.
+ * @retval None
+ */
+void TIM_ForcedOC3Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC1M Bits */
+ tmpccmr2 &= (uint32_t)~TIM_CCMR2_OC3M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr2 |= TIM_ForcedAction;
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Forces the TIMx output 4 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC4REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC4REF.
+ * @retval None
+ */
+void TIM_ForcedOC4Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC2M Bits */
+ tmpccmr2 &= (uint32_t)~TIM_CCMR2_OC4M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr2 |= ((uint32_t)TIM_ForcedAction << 8);
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Forces the TIMx output 5 waveform to active or inactive level.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC5REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC5REF.
+ * @retval None
+ */
+void TIM_ForcedOC5Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC5M Bits */
+ tmpccmr3 &= (uint32_t)~TIM_CCMR3_OC5M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr3 |= (uint32_t)(TIM_ForcedAction);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Forces the TIMx output 6 waveform to active or inactive level.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC5REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC5REF.
+ * @retval None
+ */
+void TIM_ForcedOC6Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC6M Bits */
+ tmpccmr3 &= (uint32_t)~TIM_CCMR3_OC6M;
+
+ /* Configure The Forced output Mode */
+ tmpccmr3 |= ((uint32_t)TIM_ForcedAction << 8);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR1.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC1PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC1PE Bit */
+ tmpccmr1 &= (uint32_t)(~TIM_CCMR1_OC1PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr1 |= TIM_OCPreload;
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR2.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC2PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC2PE Bit */
+ tmpccmr1 &= (uint32_t)(~TIM_CCMR1_OC2PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr1 |= ((uint32_t)TIM_OCPreload << 8);
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR3.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC3PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC3PE Bit */
+ tmpccmr2 &= (uint32_t)(~TIM_CCMR2_OC3PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr2 |= TIM_OCPreload;
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR4.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC4PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC4PE Bit */
+ tmpccmr2 &= (uint32_t)(~TIM_CCMR2_OC4PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr2 |= ((uint32_t)TIM_OCPreload << 8);
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR5.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC5PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC5PE Bit */
+ tmpccmr3 &= (uint32_t)(~TIM_CCMR3_OC5PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr3 |= (uint32_t)(TIM_OCPreload);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR6.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC6PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC5PE Bit */
+ tmpccmr3 &= (uint32_t)(~TIM_CCMR3_OC6PE);
+
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr3 |= ((uint32_t)TIM_OCPreload << 8);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 1 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC1FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC1FE Bit */
+ tmpccmr1 &= (uint32_t)~TIM_CCMR1_OC1FE;
+
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr1 |= TIM_OCFast;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 2 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC2FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC2FE Bit */
+ tmpccmr1 &= (uint32_t)(~TIM_CCMR1_OC2FE);
+
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr1 |= ((uint32_t)TIM_OCFast << 8);
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 3 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC3FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC3FE Bit */
+ tmpccmr2 &= (uint32_t)~TIM_CCMR2_OC3FE;
+
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr2 |= TIM_OCFast;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 4 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC4FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC4FE Bit */
+ tmpccmr2 &= (uint32_t)(~TIM_CCMR2_OC4FE);
+
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr2 |= ((uint32_t)TIM_OCFast << 8);
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF1 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC1Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC1CE Bit */
+ tmpccmr1 &= (uint32_t)~TIM_CCMR1_OC1CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr1 |= TIM_OCClear;
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF2 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC2Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC2CE Bit */
+ tmpccmr1 &= (uint32_t)~TIM_CCMR1_OC2CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr1 |= ((uint32_t)TIM_OCClear << 8);
+
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF3 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC3Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC3CE Bit */
+ tmpccmr2 &= (uint32_t)~TIM_CCMR2_OC3CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr2 |= TIM_OCClear;
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF4 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC4Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr2 = TIMx->CCMR2;
+
+ /* Reset the OC4CE Bit */
+ tmpccmr2 &= (uint32_t)~TIM_CCMR2_OC4CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr2 |= ((uint32_t)TIM_OCClear << 8);
+
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF5 signal on an external event
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC5Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC5CE Bit */
+ tmpccmr3 &= (uint32_t)~TIM_CCMR3_OC5CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr3 |= (uint32_t)(TIM_OCClear);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF6 signal on an external event
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC6Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint32_t tmpccmr3 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr3 = TIMx->CCMR3;
+
+ /* Reset the OC5CE Bit */
+ tmpccmr3 &= (uint32_t)~TIM_CCMR3_OC6CE;
+
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr3 |= ((uint32_t)TIM_OCClear << 8);
+
+ /* Write to TIMx CCMR3 register */
+ TIMx->CCMR3 = tmpccmr3;
+}
+
+/**
+ * @brief Selects the OCReference Clear source.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCReferenceClear: specifies the OCReference Clear source.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCReferenceClear_ETRF: The internal OCreference clear input is connected to ETRF.
+ * @arg TIM_OCReferenceClear_OCREFCLR: The internal OCreference clear input is connected to OCREF_CLR input.
+ * @retval None
+ */
+void TIM_SelectOCREFClear(TIM_TypeDef* TIMx, uint16_t TIM_OCReferenceClear)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(TIM_OCREFERENCECECLEAR_SOURCE(TIM_OCReferenceClear));
+
+ /* Set the TIM_OCReferenceClear source */
+ TIMx->SMCR &= (uint16_t)~((uint16_t)TIM_SMCR_OCCS);
+ TIMx->SMCR |= TIM_OCReferenceClear;
+}
+
+/**
+ * @brief Configures the TIMx channel 1 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC1 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC1PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC1P Bit */
+ tmpccer &= (uint32_t)(~TIM_CCER_CC1P);
+ tmpccer |= TIM_OCPolarity;
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 1N polarity.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC1N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC1NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint32_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC1NP Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC1NP;
+ tmpccer |= TIM_OCNPolarity;
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 2 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_OCPolarity: specifies the OC2 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC2PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC2P Bit */
+ tmpccer &= (uint32_t)(~TIM_CCER_CC2P);
+ tmpccer |= ((uint32_t)TIM_OCPolarity << 4);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 2N polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC2N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC2NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC2NP Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC2NP;
+ tmpccer |= ((uint32_t)TIM_OCNPolarity << 4);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 3 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC3 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC3PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC3P Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC3P;
+ tmpccer |= ((uint32_t)TIM_OCPolarity << 8);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 3N polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC3N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC3NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC3NP Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC3NP;
+ tmpccer |= ((uint32_t)TIM_OCNPolarity << 8);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 4 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC4 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC4PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC4P Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC4P;
+ tmpccer |= ((uint32_t)TIM_OCPolarity << 12);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 5 polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC5 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC5PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC5P Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC5P;
+ tmpccer |= ((uint32_t)TIM_OCPolarity << 16);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 6 polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC6 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC6PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint32_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+
+ tmpccer = TIMx->CCER;
+
+ /* Set or Reset the CC6P Bit */
+ tmpccer &= (uint32_t)~TIM_CCER_CC6P;
+ tmpccer |= ((uint32_t)TIM_OCPolarity << 20);
+
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel x.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @arg TIM_Channel_4: TIM Channel 4
+ * @arg TIM_Channel_5: TIM Channel 5
+ * @arg TIM_Channel_6: TIM Channel 6
+ * @param TIM_CCx: specifies the TIM Channel CCxE bit new state.
+ * This parameter can be: TIM_CCx_Enable or TIM_CCx_Disable.
+ * @retval None
+ */
+void TIM_CCxCmd(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint16_t TIM_CCx)
+{
+ uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_CCX(TIM_CCx));
+
+ tmp = (uint32_t)CCER_CCE_SET << (uint32_t)TIM_Channel;
+
+ /* Reset the CCxE Bit */
+ TIMx->CCER &= (uint32_t)(~tmp);
+
+ /* Set or reset the CCxE Bit */
+ TIMx->CCER |= ((uint32_t)TIM_CCx << (uint32_t)TIM_Channel);
+}
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel xN.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @param TIM_CCxN: specifies the TIM Channel CCxNE bit new state.
+ * This parameter can be: TIM_CCxN_Enable or TIM_CCxN_Disable.
+ * @retval None
+ */
+void TIM_CCxNCmd(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint16_t TIM_CCxN)
+{
+ uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_COMPLEMENTARY_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_CCXN(TIM_CCxN));
+
+ tmp = (uint32_t)CCER_CCNE_SET << (uint32_t)TIM_Channel;
+
+ /* Reset the CCxNE Bit */
+ TIMx->CCER &= (uint32_t) ~tmp;
+
+ /* Set or reset the CCxNE Bit */
+ TIMx->CCER |= ((uint32_t)TIM_CCxN << (uint32_t)TIM_Channel);
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group3 Input Capture management functions
+ * @brief Input Capture management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Input Capture management functions #####
+ ===============================================================================
+
+ *** TIM Driver: how to use it in Input Capture Mode ***
+ =======================================================
+ [..]
+ To use the Timer in Input Capture mode, the following steps are mandatory:
+
+ (#) Enable TIM clock using RCC_APBxPeriphClockCmd(RCC_APBxPeriph_TIMx, ENABLE) function
+
+ (#) Configure the TIM pins by configuring the corresponding GPIO pins
+
+ (#) Configure the Time base unit as described in the first part of this driver,
+ if needed, else the Timer will run with the default configuration:
+ (++) Autoreload value = 0xFFFF
+ (++) Prescaler value = 0x0000
+ (++) Counter mode = Up counting
+ (++) Clock Division = TIM_CKD_DIV1
+
+ (#) Fill the TIM_ICInitStruct with the desired parameters including:
+ (++) TIM Channel: TIM_Channel
+ (++) TIM Input Capture polarity: TIM_ICPolarity
+ (++) TIM Input Capture selection: TIM_ICSelection
+ (++) TIM Input Capture Prescaler: TIM_ICPrescaler
+ (++) TIM Input CApture filter value: TIM_ICFilter
+
+ (#) Call TIM_ICInit(TIMx, &TIM_ICInitStruct) to configure the desired channel with the
+ corresponding configuration and to measure only frequency or duty cycle of the input signal,
+ or,
+ Call TIM_PWMIConfig(TIMx, &TIM_ICInitStruct) to configure the desired channels with the
+ corresponding configuration and to measure the frequency and the duty cycle of the input signal
+
+ (#) Enable the NVIC or the DMA to read the measured frequency.
+
+ (#) Enable the corresponding interrupt (or DMA request) to read the Captured value,
+ using the function TIM_ITConfig(TIMx, TIM_IT_CCx) (or TIM_DMA_Cmd(TIMx, TIM_DMA_CCx))
+
+ (#) Call the TIM_Cmd(ENABLE) function to enable the TIM counter.
+
+ (#) Use TIM_GetCapturex(TIMx); to read the captured value.
+ [..]
+ (@) All other functions can be used separately to modify, if needed,
+ a specific feature of the Timer.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initializes the TIM peripheral according to the specified parameters
+ * in the TIM_ICInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_ICInit(TIM_TypeDef* TIMx, TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_POLARITY(TIM_ICInitStruct->TIM_ICPolarity));
+ assert_param(IS_TIM_IC_SELECTION(TIM_ICInitStruct->TIM_ICSelection));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICInitStruct->TIM_ICPrescaler));
+ assert_param(IS_TIM_IC_FILTER(TIM_ICInitStruct->TIM_ICFilter));
+
+ if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_1)
+ {
+ /* TI1 Configuration */
+ TI1_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_2)
+ {
+ /* TI2 Configuration */
+ TI2_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_3)
+ {
+ /* TI3 Configuration */
+ TI3_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC3Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else
+ {
+ /* TI4 Configuration */
+ TI4_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC4Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+}
+
+/**
+ * @brief Fills each TIM_ICInitStruct member with its default value.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void TIM_ICStructInit(TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ /* Set the default configuration */
+ TIM_ICInitStruct->TIM_Channel = TIM_Channel_1;
+ TIM_ICInitStruct->TIM_ICPolarity = TIM_ICPolarity_Rising;
+ TIM_ICInitStruct->TIM_ICSelection = TIM_ICSelection_DirectTI;
+ TIM_ICInitStruct->TIM_ICPrescaler = TIM_ICPSC_DIV1;
+ TIM_ICInitStruct->TIM_ICFilter = 0x00;
+}
+
+/**
+ * @brief Configures the TIM peripheral according to the specified parameters
+ * in the TIM_ICInitStruct to measure an external PWM signal.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure that contains
+ * the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_PWMIConfig(TIM_TypeDef* TIMx, TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ uint16_t icoppositepolarity = TIM_ICPolarity_Rising;
+ uint16_t icoppositeselection = TIM_ICSelection_DirectTI;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+
+ /* Select the Opposite Input Polarity */
+ if (TIM_ICInitStruct->TIM_ICPolarity == TIM_ICPolarity_Rising)
+ {
+ icoppositepolarity = TIM_ICPolarity_Falling;
+ }
+ else
+ {
+ icoppositepolarity = TIM_ICPolarity_Rising;
+ }
+ /* Select the Opposite Input */
+ if (TIM_ICInitStruct->TIM_ICSelection == TIM_ICSelection_DirectTI)
+ {
+ icoppositeselection = TIM_ICSelection_IndirectTI;
+ }
+ else
+ {
+ icoppositeselection = TIM_ICSelection_DirectTI;
+ }
+ if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_1)
+ {
+ /* TI1 Configuration */
+ TI1_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity, TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ /* TI2 Configuration */
+ TI2_Config(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else
+ {
+ /* TI2 Configuration */
+ TI2_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity, TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ /* TI1 Configuration */
+ TI1_Config(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 1 value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @retval Capture Compare 1 Register value.
+ */
+uint32_t TIM_GetCapture1(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+
+ /* Get the Capture 1 Register value */
+ return TIMx->CCR1;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 2 value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @retval Capture Compare 2 Register value.
+ */
+uint32_t TIM_GetCapture2(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+
+ /* Get the Capture 2 Register value */
+ return TIMx->CCR2;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 3 value.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @retval Capture Compare 3 Register value.
+ */
+uint32_t TIM_GetCapture3(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+
+ /* Get the Capture 3 Register value */
+ return TIMx->CCR3;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 4 value.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @retval Capture Compare 4 Register value.
+ */
+uint32_t TIM_GetCapture4(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+
+ /* Get the Capture 4 Register value */
+ return TIMx->CCR4;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 1 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture1 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC1Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+
+ /* Reset the IC1PSC Bits */
+ TIMx->CCMR1 &= (uint32_t)~TIM_CCMR1_IC1PSC;
+
+ /* Set the IC1PSC value */
+ TIMx->CCMR1 |= TIM_ICPSC;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 2 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture2 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC2Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+
+ /* Reset the IC2PSC Bits */
+ TIMx->CCMR1 &= (uint32_t)~TIM_CCMR1_IC2PSC;
+
+ /* Set the IC2PSC value */
+ TIMx->CCMR1 |= (uint32_t)((uint32_t)TIM_ICPSC << 8);
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 3 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture3 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC3Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+
+ /* Reset the IC3PSC Bits */
+ TIMx->CCMR2 &= (uint16_t)~TIM_CCMR2_IC3PSC;
+
+ /* Set the IC3PSC value */
+ TIMx->CCMR2 |= TIM_ICPSC;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 4 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture4 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC4Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+
+ /* Reset the IC4PSC Bits */
+ TIMx->CCMR2 &= (uint16_t)~TIM_CCMR2_IC4PSC;
+
+ /* Set the IC4PSC value */
+ TIMx->CCMR2 |= (uint16_t)(TIM_ICPSC << 8);
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group4 Advanced-control timers (TIM1 and TIM8) specific features
+ * @brief Advanced-control timers (TIM1 and TIM8) specific features
+ *
+@verbatim
+ ===============================================================================
+ ##### Advanced-control timers (TIM1 and TIM8) specific features #####
+ ===============================================================================
+
+ *** TIM Driver: how to use the Break feature ***
+ ================================================
+ [..]
+ After configuring the Timer channel(s) in the appropriate Output Compare mode:
+
+ (#) Fill the TIM_BDTRInitStruct with the desired parameters for the Timer
+ Break Polarity, dead time, Lock level, the OSSI/OSSR State and the
+ AOE(automatic output enable).
+
+ (#) Call TIM_BDTRConfig(TIMx, &TIM_BDTRInitStruct) to configure the Timer
+
+ (#) Enable the Main Output using TIM_CtrlPWMOutputs(TIM1, ENABLE)
+
+ (#) Once the break even occurs, the Timer's output signals are put in reset
+ state or in a known state (according to the configuration made in
+ TIM_BDTRConfig() function).
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State
+ * and the AOE(automatic output enable).
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIM
+ * @param TIM_BDTRInitStruct: pointer to a TIM_BDTRInitTypeDef structure that
+ * contains the BDTR Register configuration information for the TIM peripheral.
+ * @retval None
+ */
+void TIM_BDTRConfig(TIM_TypeDef* TIMx, TIM_BDTRInitTypeDef *TIM_BDTRInitStruct)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OSSR_STATE(TIM_BDTRInitStruct->TIM_OSSRState));
+ assert_param(IS_TIM_OSSI_STATE(TIM_BDTRInitStruct->TIM_OSSIState));
+ assert_param(IS_TIM_LOCK_LEVEL(TIM_BDTRInitStruct->TIM_LOCKLevel));
+ assert_param(IS_TIM_BREAK_STATE(TIM_BDTRInitStruct->TIM_Break));
+ assert_param(IS_TIM_BREAK_POLARITY(TIM_BDTRInitStruct->TIM_BreakPolarity));
+ assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(TIM_BDTRInitStruct->TIM_AutomaticOutput));
+
+ /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State,
+ the OSSI State, the dead time value and the Automatic Output Enable Bit */
+ TIMx->BDTR = (uint32_t)TIM_BDTRInitStruct->TIM_OSSRState | TIM_BDTRInitStruct->TIM_OSSIState |
+ TIM_BDTRInitStruct->TIM_LOCKLevel | TIM_BDTRInitStruct->TIM_DeadTime |
+ TIM_BDTRInitStruct->TIM_Break | TIM_BDTRInitStruct->TIM_BreakPolarity |
+ TIM_BDTRInitStruct->TIM_AutomaticOutput;
+}
+
+/**
+ * @brief Configures the Break1 feature.
+ * @param TIMx: where x can be 1 or 8 to select the TIM
+ * @param TIM_Break1Polarity: specifies the Break1 polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_Break1Polarity_Low: Break1 input is active low
+ * @arg TIM_Break1Polarity_High: Break1 input is active high
+ * @param TIM_Break1Filter: specifies the Break1 filter value.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_Break1Config(TIM_TypeDef* TIMx, uint32_t TIM_Break1Polarity, uint8_t TIM_Break1Filter)
+{ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_BREAK1_FILTER(TIM_Break1Filter));
+
+ /* Reset the BKP and BKF Bits */
+ TIMx->BDTR &= (uint32_t)~ (TIM_BDTR_BKP | TIM_BDTR_BKF);
+ /* Configure the Break1 polarity and filter */
+ TIMx->BDTR |= TIM_Break1Polarity |((uint32_t)TIM_Break1Filter << 16);
+}
+
+/**
+ * @brief Configures the Break2 feature.
+ * @param TIMx: where x can be 1 or 8 to select the TIM
+ * @param TIM_Break2Polarity: specifies the Break2 polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_Break2Polarity_Low: Break2 input is active low
+ * @arg TIM_Break2Polarity_High: Break2 input is active high
+ * @param TIM_Break2Filter: specifies the Break2 filter value.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_Break2Config(TIM_TypeDef* TIMx, uint32_t TIM_Break2Polarity, uint8_t TIM_Break2Filter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_BREAK2_FILTER(TIM_Break2Filter));
+
+ /* Reset the BKP and BKF Bits */
+ TIMx->BDTR &= (uint32_t)~ (TIM_BDTR_BK2P | TIM_BDTR_BK2F);
+
+ /* Configure the Break1 polarity and filter */
+ TIMx->BDTR |= TIM_Break2Polarity |((uint32_t)TIM_Break2Filter << 20);
+}
+
+/**
+ * @brief Enables or disables the TIM Break1 input.
+ * @param TIMx: where x can be 1, 8, 1, 16 or 17 to select the TIMx peripheral.
+ * @param NewState: new state of the TIM Break1 input.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_Break1Cmd(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Break1 */
+ TIMx->BDTR |= TIM_BDTR_BKE;
+ }
+ else
+ {
+ /* Disable the Break1 */
+ TIMx->BDTR &= (uint32_t)~TIM_BDTR_BKE;
+ }
+}
+
+/**
+ * @brief Enables or disables the TIM Break2 input.
+ * @param TIMx: where x can be 1 or 8 to select the TIMx peripheral.
+ * @param NewState: new state of the TIM Break2 input.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_Break2Cmd(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Break1 */
+ TIMx->BDTR |= TIM_BDTR_BK2E;
+ }
+ else
+ {
+ /* Disable the Break1 */
+ TIMx->BDTR &= (uint32_t)~TIM_BDTR_BK2E;
+ }
+}
+
+/**
+ * @brief Fills each TIM_BDTRInitStruct member with its default value.
+ * @param TIM_BDTRInitStruct: pointer to a TIM_BDTRInitTypeDef structure which
+ * will be initialized.
+ * @retval None
+ */
+void TIM_BDTRStructInit(TIM_BDTRInitTypeDef* TIM_BDTRInitStruct)
+{
+ /* Set the default configuration */
+ TIM_BDTRInitStruct->TIM_OSSRState = TIM_OSSRState_Disable;
+ TIM_BDTRInitStruct->TIM_OSSIState = TIM_OSSIState_Disable;
+ TIM_BDTRInitStruct->TIM_LOCKLevel = TIM_LOCKLevel_OFF;
+ TIM_BDTRInitStruct->TIM_DeadTime = 0x00;
+ TIM_BDTRInitStruct->TIM_Break = TIM_Break_Disable;
+ TIM_BDTRInitStruct->TIM_BreakPolarity = TIM_BreakPolarity_Low;
+ TIM_BDTRInitStruct->TIM_AutomaticOutput = TIM_AutomaticOutput_Disable;
+}
+
+/**
+ * @brief Enables or disables the TIM peripheral Main Outputs.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral.
+ * @param NewState: new state of the TIM peripheral Main Outputs.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_CtrlPWMOutputs(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the TIM Main Output */
+ TIMx->BDTR |= TIM_BDTR_MOE;
+ }
+ else
+ {
+ /* Disable the TIM Main Output */
+ TIMx->BDTR &= (uint16_t)~TIM_BDTR_MOE;
+ }
+}
+
+/**
+ * @brief Selects the TIM peripheral Commutation event.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral
+ * @param NewState: new state of the Commutation event.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectCOM(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the COM Bit */
+ TIMx->CR2 |= TIM_CR2_CCUS;
+ }
+ else
+ {
+ /* Reset the COM Bit */
+ TIMx->CR2 &= (uint16_t)~TIM_CR2_CCUS;
+ }
+}
+
+/**
+ * @brief Sets or Resets the TIM peripheral Capture Compare Preload Control bit.
+ * @param TIMx: where x can be 1 or 8 to select the TIMx peripheral
+ * @param NewState: new state of the Capture Compare Preload Control bit
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_CCPreloadControl(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the CCPC Bit */
+ TIMx->CR2 |= TIM_CR2_CCPC;
+ }
+ else
+ {
+ /* Reset the CCPC Bit */
+ TIMx->CR2 &= (uint16_t)~TIM_CR2_CCPC;
+ }
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group5 Interrupts DMA and flags management functions
+ * @brief Interrupts, DMA and flags management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Interrupts, DMA and flags management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables or disables the specified TIM interrupts.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIMx peripheral.
+ * @param TIM_IT: specifies the TIM interrupts sources to be enabled or disabled.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_IT_Update: TIM update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ *
+ * @note For TIM6 and TIM7 only the parameter TIM_IT_Update can be used
+ * @note For TIM9 and TIM12 only one of the following parameters can be used: TIM_IT_Update,
+ * TIM_IT_CC1, TIM_IT_CC2 or TIM_IT_Trigger.
+ * @note For TIM10, TIM11, TIM13 and TIM14 only one of the following parameters can
+ * be used: TIM_IT_Update or TIM_IT_CC1
+ * @note TIM_IT_COM and TIM_IT_Break can be used only with TIM1 and TIM8
+ *
+ * @param NewState: new state of the TIM interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_ITConfig(TIM_TypeDef* TIMx, uint16_t TIM_IT, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_IT(TIM_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Interrupt sources */
+ TIMx->DIER |= TIM_IT;
+ }
+ else
+ {
+ /* Disable the Interrupt sources */
+ TIMx->DIER &= (uint16_t)~TIM_IT;
+ }
+}
+
+/**
+ * @brief Configures the TIMx event to be generate by software.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_EventSource: specifies the event source.
+ * This parameter can be one or more of the following values:
+ * @arg TIM_EventSource_Update: Timer update Event source
+ * @arg TIM_EventSource_CC1: Timer Capture Compare 1 Event source
+ * @arg TIM_EventSource_CC2: Timer Capture Compare 2 Event source
+ * @arg TIM_EventSource_CC3: Timer Capture Compare 3 Event source
+ * @arg TIM_EventSource_CC4: Timer Capture Compare 4 Event source
+ * @arg TIM_EventSource_COM: Timer COM event source
+ * @arg TIM_EventSource_Trigger: Timer Trigger Event source
+ * @arg TIM_EventSource_Break: Timer Break event source
+ *
+ * @note TIM6 and TIM7 can only generate an update event.
+ * @note TIM_EventSource_COM and TIM_EventSource_Break are used only with TIM1 and TIM8.
+ *
+ * @retval None
+ */
+void TIM_GenerateEvent(TIM_TypeDef* TIMx, uint16_t TIM_EventSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_EVENT_SOURCE(TIM_EventSource));
+
+ /* Set the event sources */
+ TIMx->EGR = TIM_EventSource;
+}
+
+/**
+ * @brief Checks whether the specified TIM flag is set or not.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg TIM_FLAG_Update: TIM update Flag
+ * @arg TIM_FLAG_CC1: TIM Capture Compare 1 Flag
+ * @arg TIM_FLAG_CC2: TIM Capture Compare 2 Flag
+ * @arg TIM_FLAG_CC3: TIM Capture Compare 3 Flag
+ * @arg TIM_FLAG_CC4: TIM Capture Compare 4 Flag
+ * @arg TIM_FLAG_CC5: TIM Capture Compare 5 Flag
+ * @arg TIM_FLAG_CC6: TIM Capture Compare 6 Flag
+ * @arg TIM_FLAG_COM: TIM Commutation Flag
+ * @arg TIM_FLAG_Trigger: TIM Trigger Flag
+ * @arg TIM_FLAG_Break: TIM Break Flag
+ * @arg TIM_FLAG_CC1OF: TIM Capture Compare 1 over capture Flag
+ * @arg TIM_FLAG_CC2OF: TIM Capture Compare 2 over capture Flag
+ * @arg TIM_FLAG_CC3OF: TIM Capture Compare 3 over capture Flag
+ * @arg TIM_FLAG_CC4OF: TIM Capture Compare 4 over capture Flag
+ *
+ * @note TIM6 and TIM7 can have only one update flag.
+ * @note TIM_FLAG_COM and TIM_FLAG_Break are used only with TIM1 and TIM8.
+ *
+ * @retval The new state of TIM_FLAG (SET or RESET).
+ */
+FlagStatus TIM_GetFlagStatus(TIM_TypeDef* TIMx, uint32_t TIM_FLAG)
+{
+ ITStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_GET_FLAG(TIM_FLAG));
+
+
+ if ((TIMx->SR & TIM_FLAG) != RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the TIMx's pending flags.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_FLAG: specifies the flag bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_FLAG_Update: TIM update Flag
+ * @arg TIM_FLAG_CC1: TIM Capture Compare 1 Flag
+ * @arg TIM_FLAG_CC2: TIM Capture Compare 2 Flag
+ * @arg TIM_FLAG_CC3: TIM Capture Compare 3 Flag
+ * @arg TIM_FLAG_CC4: TIM Capture Compare 4 Flag
+ * @arg TIM_FLAG_CC5: TIM Capture Compare 5 Flag
+ * @arg TIM_FLAG_CC6: TIM Capture Compare 6 Flag
+ * @arg TIM_FLAG_COM: TIM Commutation Flag
+ * @arg TIM_FLAG_Trigger: TIM Trigger Flag
+ * @arg TIM_FLAG_Break: TIM Break Flag
+ * @arg TIM_FLAG_CC1OF: TIM Capture Compare 1 over capture Flag
+ * @arg TIM_FLAG_CC2OF: TIM Capture Compare 2 over capture Flag
+ * @arg TIM_FLAG_CC3OF: TIM Capture Compare 3 over capture Flag
+ * @arg TIM_FLAG_CC4OF: TIM Capture Compare 4 over capture Flag
+ *
+ * @note TIM6 and TIM7 can have only one update flag.
+ * @note TIM_FLAG_COM and TIM_FLAG_Break are used only with TIM1 and TIM8.
+ *
+ * @retval None
+ */
+void TIM_ClearFlag(TIM_TypeDef* TIMx, uint16_t TIM_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Clear the flags */
+ TIMx->SR = (uint16_t)~TIM_FLAG;
+}
+
+/**
+ * @brief Checks whether the TIM interrupt has occurred or not.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_IT: specifies the TIM interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg TIM_IT_Update: TIM update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ *
+ * @note TIM6 and TIM7 can generate only an update interrupt.
+ * @note TIM_IT_COM and TIM_IT_Break are used only with TIM1 and TIM8.
+ *
+ * @retval The new state of the TIM_IT(SET or RESET).
+ */
+ITStatus TIM_GetITStatus(TIM_TypeDef* TIMx, uint16_t TIM_IT)
+{
+ ITStatus bitstatus = RESET;
+ uint16_t itstatus = 0x0, itenable = 0x0;
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_GET_IT(TIM_IT));
+
+ itstatus = TIMx->SR & TIM_IT;
+
+ itenable = TIMx->DIER & TIM_IT;
+ if ((itstatus != (uint16_t)RESET) && (itenable != (uint16_t)RESET))
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the TIMx's interrupt pending bits.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_IT: specifies the pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_IT_Update: TIM1 update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ *
+ * @note TIM6 and TIM7 can generate only an update interrupt.
+ * @note TIM_IT_COM and TIM_IT_Break are used only with TIM1 and TIM8.
+ *
+ * @retval None
+ */
+void TIM_ClearITPendingBit(TIM_TypeDef* TIMx, uint16_t TIM_IT)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ /* Clear the IT pending Bit */
+ TIMx->SR = (uint16_t)~TIM_IT;
+}
+
+/**
+ * @brief Configures the TIMx's DMA interface.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_DMABase: DMA Base address.
+ * This parameter can be one of the following values:
+ * @arg TIM_DMABase_CR1
+ * @arg TIM_DMABase_CR2
+ * @arg TIM_DMABase_SMCR
+ * @arg TIM_DMABase_DIER
+ * @arg TIM1_DMABase_SR
+ * @arg TIM_DMABase_EGR
+ * @arg TIM_DMABase_CCMR1
+ * @arg TIM_DMABase_CCMR2
+ * @arg TIM_DMABase_CCER
+ * @arg TIM_DMABase_CNT
+ * @arg TIM_DMABase_PSC
+ * @arg TIM_DMABase_ARR
+ * @arg TIM_DMABase_RCR
+ * @arg TIM_DMABase_CCR1
+ * @arg TIM_DMABase_CCR2
+ * @arg TIM_DMABase_CCR3
+ * @arg TIM_DMABase_CCR4
+ * @arg TIM_DMABase_BDTR
+ * @arg TIM_DMABase_DCR
+ * @param TIM_DMABurstLength: DMA Burst length. This parameter can be one value
+ * between: TIM_DMABurstLength_1Transfer and TIM_DMABurstLength_18Transfers.
+ * @retval None
+ */
+void TIM_DMAConfig(TIM_TypeDef* TIMx, uint16_t TIM_DMABase, uint16_t TIM_DMABurstLength)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_DMA_BASE(TIM_DMABase));
+ assert_param(IS_TIM_DMA_LENGTH(TIM_DMABurstLength));
+
+ /* Set the DMA Base and the DMA Burst Length */
+ TIMx->DCR = TIM_DMABase | TIM_DMABurstLength;
+}
+
+/**
+ * @brief Enables or disables the TIMx's DMA Requests.
+ * @param TIMx: where x can be 1, 2, 3, 4, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_DMASource: specifies the DMA Request sources.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_DMA_Update: TIM update Interrupt source
+ * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
+ * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
+ * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
+ * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
+ * @arg TIM_DMA_COM: TIM Commutation DMA source
+ * @arg TIM_DMA_Trigger: TIM Trigger DMA source
+ * @param NewState: new state of the DMA Request sources.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_DMACmd(TIM_TypeDef* TIMx, uint16_t TIM_DMASource, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_DMA_SOURCE(TIM_DMASource));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the DMA sources */
+ TIMx->DIER |= TIM_DMASource;
+ }
+ else
+ {
+ /* Disable the DMA sources */
+ TIMx->DIER &= (uint16_t)~TIM_DMASource;
+ }
+}
+
+/**
+ * @brief Selects the TIMx peripheral Capture Compare DMA source.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param NewState: new state of the Capture Compare DMA source
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectCCDMA(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the CCDS Bit */
+ TIMx->CR2 |= TIM_CR2_CCDS;
+ }
+ else
+ {
+ /* Reset the CCDS Bit */
+ TIMx->CR2 &= (uint16_t)~TIM_CR2_CCDS;
+ }
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group6 Clocks management functions
+ * @brief Clocks management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Clocks management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the TIMx internal Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @retval None
+ */
+void TIM_InternalClockConfig(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+
+ /* Disable slave mode to clock the prescaler directly with the internal clock */
+ TIMx->SMCR &= (uint16_t)~TIM_SMCR_SMS;
+}
+
+/**
+ * @brief Configures the TIMx Internal Trigger as External Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param TIM_InputTriggerSource: Trigger source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal Trigger 0
+ * @arg TIM_TS_ITR1: Internal Trigger 1
+ * @arg TIM_TS_ITR2: Internal Trigger 2
+ * @arg TIM_TS_ITR3: Internal Trigger 3
+ * @retval None
+ */
+void TIM_ITRxExternalClockConfig(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_INTERNAL_TRIGGER_SELECTION(TIM_InputTriggerSource));
+
+ /* Select the Internal Trigger */
+ TIM_SelectInputTrigger(TIMx, TIM_InputTriggerSource);
+
+ /* Select the External clock mode1 */
+ TIMx->SMCR |= TIM_SlaveMode_External1;
+}
+
+/**
+ * @brief Configures the TIMx Trigger as External Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15
+ * to select the TIM peripheral.
+ * @param TIM_TIxExternalCLKSource: Trigger source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TIxExternalCLK1Source_TI1ED: TI1 Edge Detector
+ * @arg TIM_TIxExternalCLK1Source_TI1: Filtered Timer Input 1
+ * @arg TIM_TIxExternalCLK1Source_TI2: Filtered Timer Input 2
+ * @param TIM_ICPolarity: specifies the TIx Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param ICFilter: specifies the filter value.
+ * This parameter must be a value between 0x0 and 0xF.
+ * @retval None
+ */
+void TIM_TIxExternalClockConfig(TIM_TypeDef* TIMx, uint16_t TIM_TIxExternalCLKSource,
+ uint16_t TIM_ICPolarity, uint16_t ICFilter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_POLARITY(TIM_ICPolarity));
+ assert_param(IS_TIM_IC_FILTER(ICFilter));
+
+ /* Configure the Timer Input Clock Source */
+ if (TIM_TIxExternalCLKSource == TIM_TIxExternalCLK1Source_TI2)
+ {
+ TI2_Config(TIMx, TIM_ICPolarity, TIM_ICSelection_DirectTI, ICFilter);
+ }
+ else
+ {
+ TI1_Config(TIMx, TIM_ICPolarity, TIM_ICSelection_DirectTI, ICFilter);
+ }
+ /* Select the Trigger source */
+ TIM_SelectInputTrigger(TIMx, TIM_TIxExternalCLKSource);
+ /* Select the External clock mode1 */
+ TIMx->SMCR |= TIM_SlaveMode_External1;
+}
+
+/**
+ * @brief Configures the External clock Mode1
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRClockMode1Config(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler,
+ uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter)
+{
+ uint16_t tmpsmcr = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+ /* Configure the ETR Clock source */
+ TIM_ETRConfig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter);
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+
+ /* Reset the SMS Bits */
+ tmpsmcr &= (uint16_t)~TIM_SMCR_SMS;
+
+ /* Select the External clock mode1 */
+ tmpsmcr |= TIM_SlaveMode_External1;
+
+ /* Select the Trigger selection : ETRF */
+ tmpsmcr &= (uint16_t)~TIM_SMCR_TS;
+ tmpsmcr |= TIM_TS_ETRF;
+
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+
+/**
+ * @brief Configures the External clock Mode2
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRClockMode2Config(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler,
+ uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+
+ /* Configure the ETR Clock source */
+ TIM_ETRConfig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter);
+
+ /* Enable the External clock mode2 */
+ TIMx->SMCR |= TIM_SMCR_ECE;
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group7 Synchronization management functions
+ * @brief Synchronization management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Synchronization management functions #####
+ ===============================================================================
+
+ *** TIM Driver: how to use it in synchronization Mode ***
+ =========================================================
+ [..] Case of two/several Timers
+
+ (#) Configure the Master Timers using the following functions:
+ (++) void TIM_SelectOutputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_TRGOSource);
+ (++) void TIM_SelectMasterSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_MasterSlaveMode);
+ (#) Configure the Slave Timers using the following functions:
+ (++) void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource);
+ (++) void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_SlaveMode);
+
+ [..] Case of Timers and external trigger(ETR pin)
+
+ (#) Configure the External trigger using this function:
+ (++) void TIM_ETRConfig(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity,
+ uint16_t ExtTRGFilter);
+ (#) Configure the Slave Timers using the following functions:
+ (++) void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource);
+ (++) void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_SlaveMode);
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Selects the Input Trigger source
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15
+ * to select the TIM peripheral.
+ * @param TIM_InputTriggerSource: The Input Trigger source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal Trigger 0
+ * @arg TIM_TS_ITR1: Internal Trigger 1
+ * @arg TIM_TS_ITR2: Internal Trigger 2
+ * @arg TIM_TS_ITR3: Internal Trigger 3
+ * @arg TIM_TS_TI1F_ED: TI1 Edge Detector
+ * @arg TIM_TS_TI1FP1: Filtered Timer Input 1
+ * @arg TIM_TS_TI2FP2: Filtered Timer Input 2
+ * @arg TIM_TS_ETRF: External Trigger input
+ * @retval None
+ */
+void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource)
+{
+ uint16_t tmpsmcr = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_TRIGGER_SELECTION(TIM_InputTriggerSource));
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+
+ /* Reset the TS Bits */
+ tmpsmcr &= (uint16_t)~TIM_SMCR_TS;
+
+ /* Set the Input Trigger source */
+ tmpsmcr |= TIM_InputTriggerSource;
+
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+
+/**
+ * @brief Selects the TIMx Trigger Output Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 6, 7, 8 or 15 to select the TIM peripheral.
+ *
+ * @param TIM_TRGOSource: specifies the Trigger Output source.
+ * This parameter can be one of the following values:
+ *
+ * - For all TIMx
+ * @arg TIM_TRGOSource_Reset: The UG bit in the TIM_EGR register is used as the trigger output(TRGO)
+ * @arg TIM_TRGOSource_Enable: The Counter Enable CEN is used as the trigger output(TRGO)
+ * @arg TIM_TRGOSource_Update: The update event is selected as the trigger output(TRGO)
+ *
+ * - For all TIMx except TIM6 and TIM7
+ * @arg TIM_TRGOSource_OC1: The trigger output sends a positive pulse when the CC1IF flag
+ * is to be set, as soon as a capture or compare match occurs(TRGO)
+ * @arg TIM_TRGOSource_OC1Ref: OC1REF signal is used as the trigger output(TRGO)
+ * @arg TIM_TRGOSource_OC2Ref: OC2REF signal is used as the trigger output(TRGO)
+ * @arg TIM_TRGOSource_OC3Ref: OC3REF signal is used as the trigger output(TRGO)
+ * @arg TIM_TRGOSource_OC4Ref: OC4REF signal is used as the trigger output(TRGO)
+ *
+ * @retval None
+ */
+void TIM_SelectOutputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_TRGOSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST7_PERIPH(TIMx));
+ assert_param(IS_TIM_TRGO_SOURCE(TIM_TRGOSource));
+
+ /* Reset the MMS Bits */
+ TIMx->CR2 &= (uint16_t)~TIM_CR2_MMS;
+ /* Select the TRGO source */
+ TIMx->CR2 |= TIM_TRGOSource;
+}
+
+/**
+ * @brief Selects the TIMx Trigger Output Mode2 (TRGO2).
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ *
+ * @param TIM_TRGO2Source: specifies the Trigger Output source.
+ * This parameter can be one of the following values:
+ *
+ * - For all TIMx
+ * @arg TIM_TRGOSource_Reset: The UG bit in the TIM_EGR register is used as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_Enable: The Counter Enable CEN is used as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_Update: The update event is selected as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_OC1: The trigger output sends a positive pulse when the CC1IF flag
+ * is to be set, as soon as a capture or compare match occurs(TRGO2)
+ * @arg TIM_TRGOSource_OC1Ref: OC1REF signal is used as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_OC2Ref: OC2REF signal is used as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_OC3Ref: OC3REF signal is used as the trigger output(TRGO2)
+ * @arg TIM_TRGOSource_OC4Ref: OC4REF signal is used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC4Ref_RisingFalling: OC4Ref Rising and Falling are used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC6Ref_RisingFalling: OC6Ref Rising and Falling are used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC4RefRising_OC6RefRising: OC4Ref Rising and OC6Ref Rising are used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC4RefRising_OC6RefFalling: OC4Ref Rising and OC6Ref Falling are used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC5RefRising_OC6RefRising: OC5Ref Rising and OC6Ref Rising are used as the trigger output(TRGO2)
+ * @arg TIM_TRGO2Source_OC5RefRising_OC6RefFalling: OC5Ref Rising and OC6Ref Falling are used as the trigger output(TRGO2)
+ *
+ * @retval None
+ */
+void TIM_SelectOutputTrigger2(TIM_TypeDef* TIMx, uint32_t TIM_TRGO2Source)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_TRGO2_SOURCE(TIM_TRGO2Source));
+
+ /* Reset the MMS Bits */
+ TIMx->CR2 &= (uint32_t)~TIM_CR2_MMS2;
+ /* Select the TRGO source */
+ TIMx->CR2 |= TIM_TRGO2Source;
+}
+
+/**
+ * @brief Selects the TIMx Slave Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM peripheral.
+ * @param TIM_SlaveMode: specifies the Timer Slave Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_SlaveMode_Reset: Rising edge of the selected trigger signal(TRGI) reinitialize
+ * the counter and triggers an update of the registers
+ * @arg TIM_SlaveMode_Gated: The counter clock is enabled when the trigger signal (TRGI) is high
+ * @arg TIM_SlaveMode_Trigger: The counter starts at a rising edge of the trigger TRGI
+ * @arg TIM_SlaveMode_External1: Rising edges of the selected trigger (TRGI) clock the counter
+ * @arg TIM_SlaveMode_Combined_ResetTrigger: Rising edge of the selected trigger input (TRGI)
+ * reinitializes the counter, generates an update
+ * of the registers and starts the counter.
+ * @retval None
+ */
+void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint32_t TIM_SlaveMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_SLAVE_MODE(TIM_SlaveMode));
+
+ /* Reset the SMS Bits */
+ TIMx->SMCR &= (uint32_t)~TIM_SMCR_SMS;
+
+ /* Select the Slave Mode */
+ TIMx->SMCR |= (uint32_t)TIM_SlaveMode;
+}
+
+/**
+ * @brief Sets or Resets the TIMx Master/Slave Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM peripheral.
+ * @param TIM_MasterSlaveMode: specifies the Timer Master Slave Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_MasterSlaveMode_Enable: synchronization between the current timer
+ * and its slaves (through TRGO)
+ * @arg TIM_MasterSlaveMode_Disable: No action
+ * @retval None
+ */
+void TIM_SelectMasterSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_MasterSlaveMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_MSM_STATE(TIM_MasterSlaveMode));
+
+ /* Reset the MSM Bit */
+ TIMx->SMCR &= (uint16_t)~TIM_SMCR_MSM;
+
+ /* Set or Reset the MSM Bit */
+ TIMx->SMCR |= TIM_MasterSlaveMode;
+}
+
+/**
+ * @brief Configures the TIMx External Trigger (ETR).
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRConfig(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler,
+ uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter)
+{
+ uint16_t tmpsmcr = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+
+ tmpsmcr = TIMx->SMCR;
+
+ /* Reset the ETR Bits */
+ tmpsmcr &= SMCR_ETR_MASK;
+
+ /* Set the Prescaler, the Filter value and the Polarity */
+ tmpsmcr |= (uint16_t)(TIM_ExtTRGPrescaler | (uint16_t)(TIM_ExtTRGPolarity | (uint16_t)(ExtTRGFilter << (uint16_t)8)));
+
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group8 Specific interface management functions
+ * @brief Specific interface management functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Specific interface management functions #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the TIMx Encoder Interface.
+ * @param TIMx: where x can be 1, 2, 3, 4 or 8 to select the TIM
+ * peripheral.
+ * @param TIM_EncoderMode: specifies the TIMx Encoder Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_EncoderMode_TI1: Counter counts on TI1FP1 edge depending on TI2FP2 level.
+ * @arg TIM_EncoderMode_TI2: Counter counts on TI2FP2 edge depending on TI1FP1 level.
+ * @arg TIM_EncoderMode_TI12: Counter counts on both TI1FP1 and TI2FP2 edges depending
+ * on the level of the other input.
+ * @param TIM_IC1Polarity: specifies the IC1 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Falling: IC Falling edge.
+ * @arg TIM_ICPolarity_Rising: IC Rising edge.
+ * @param TIM_IC2Polarity: specifies the IC2 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Falling: IC Falling edge.
+ * @arg TIM_ICPolarity_Rising: IC Rising edge.
+ * @retval None
+ */
+void TIM_EncoderInterfaceConfig(TIM_TypeDef* TIMx, uint16_t TIM_EncoderMode,
+ uint16_t TIM_IC1Polarity, uint16_t TIM_IC2Polarity)
+{
+ uint16_t tmpsmcr = 0;
+ uint16_t tmpccmr1 = 0;
+ uint16_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_ENCODER_MODE(TIM_EncoderMode));
+ assert_param(IS_TIM_IC_POLARITY(TIM_IC1Polarity));
+ assert_param(IS_TIM_IC_POLARITY(TIM_IC2Polarity));
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+
+ /* Set the encoder Mode */
+ tmpsmcr &= (uint16_t)~TIM_SMCR_SMS;
+ tmpsmcr |= TIM_EncoderMode;
+
+ /* Select the Capture Compare 1 and the Capture Compare 2 as input */
+ tmpccmr1 &= ((uint16_t)~TIM_CCMR1_CC1S) & ((uint16_t)~TIM_CCMR1_CC2S);
+ tmpccmr1 |= TIM_CCMR1_CC1S_0 | TIM_CCMR1_CC2S_0;
+
+ /* Set the TI1 and the TI2 Polarities */
+ tmpccer &= ((uint16_t)~TIM_CCER_CC1P) & ((uint16_t)~TIM_CCER_CC2P);
+ tmpccer |= (uint16_t)(TIM_IC1Polarity | (uint16_t)(TIM_IC2Polarity << (uint16_t)4));
+
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Enables or disables the TIMx's Hall sensor interface.
+ * @param TIMx: where x can be 1, 2, 3, 4, 8 or 15 to select the TIM
+ * peripheral.
+ * @param NewState: new state of the TIMx Hall sensor interface.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectHallSensor(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Set the TI1S Bit */
+ TIMx->CR2 |= TIM_CR2_TI1S;
+ }
+ else
+ {
+ /* Reset the TI1S Bit */
+ TIMx->CR2 &= (uint16_t)~TIM_CR2_TI1S;
+ }
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Group9 Specific remapping management function
+ * @brief Specific remapping management function
+ *
+@verbatim
+ ===============================================================================
+ ##### Specific remapping management function #####
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the TIM16 Remapping input Capabilities.
+ * @param TIMx: where x can be 1, 8 or 16 to select the TIM peripheral.
+ * @param TIM_Remap: specifies the TIM input reampping source.
+ * This parameter can be one of the following values:
+ * @arg TIM16_GPIO: TIM16 Channel 1 is connected to GPIO.
+ * @arg TIM16_RTC_CLK: TIM16 Channel 1 is connected to RTC input clock.
+ * @arg TIM16_HSE_DIV32: TIM16 Channel 1 is connected to HSE/32 clock.
+ * @arg TIM16_MCO: TIM16 Channel 1 is connected to MCO clock.
+ * @arg TIM1_ADC1_AWDG1: TIM1 ETR is connected to ADC1 AWDG1.
+ * @arg TIM1_ADC1_AWDG2: TIM1 ETR is connected to ADC1 AWDG2.
+ * @arg TIM1_ADC1_AWDG3: TIM1 ETR is connected to ADC1 AWDG3.
+ * @arg TIM1_ADC4_AWDG1: TIM1 ETR is connected to ADC4 AWDG1.
+ * @arg TIM1_ADC4_AWDG2: TIM1 ETR is connected to ADC4 AWDG2.
+ * @arg TIM1_ADC4_AWDG3: TIM1 ETR is connected to ADC4 AWDG3.
+ * @arg TIM8_ADC2_AWDG1: TIM8 ETR is connected to ADC2 AWDG1.
+ * @arg TIM8_ADC2_AWDG2: TIM8 ETR is connected to ADC2 AWDG2.
+ * @arg TIM8_ADC2_AWDG3: TIM8 ETR is connected to ADC2 AWDG3.
+ * @arg TIM8_ADC4_AWDG1: TIM8 ETR is connected to ADC4 AWDG1.
+ * @arg TIM8_ADC4_AWDG2: TIM8 ETR is connected to ADC4 AWDG2.
+ * @arg TIM8_ADC4_AWDG3: TIM8 ETR is connected to ADC4 AWDG3.
+ * @retval : None
+ */
+void TIM_RemapConfig(TIM_TypeDef* TIMx, uint16_t TIM_Remap)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_REMAP(TIM_Remap));
+
+ /* Set the Timer remapping configuration */
+ TIMx->OR = TIM_Remap;
+}
+/**
+ * @}
+ */
+
+/**
+ * @brief Configure the TI1 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 10, 11, 12, 13 or 14
+ * to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @arg TIM_ICPolarity_BothEdge
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2.
+ * @arg TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI1_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint32_t tmpccmr1 = 0, tmpccer = 0;
+
+ /* Disable the Channel 1: Reset the CC1E Bit */
+ TIMx->CCER &= (uint32_t)~TIM_CCER_CC1E;
+ tmpccmr1 = TIMx->CCMR1;
+ tmpccer = TIMx->CCER;
+
+ /* Select the Input and set the filter */
+ tmpccmr1 &= ((uint32_t)~TIM_CCMR1_CC1S) & ((uint32_t)~TIM_CCMR1_IC1F);
+ tmpccmr1 |= (uint32_t)(TIM_ICSelection | (uint32_t)((uint32_t)TIM_ICFilter << 4));
+
+ /* Select the Polarity and set the CC1E Bit */
+ tmpccer &= (uint32_t)~(TIM_CCER_CC1P | TIM_CCER_CC1NP);
+ tmpccer |= (uint32_t)(TIM_ICPolarity | (uint32_t)TIM_CCER_CC1E);
+
+ /* Write to TIMx CCMR1 and CCER registers */
+ TIMx->CCMR1 = tmpccmr1;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI2 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9 or 12 to select the TIM
+ * peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @arg TIM_ICPolarity_BothEdge
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1.
+ * @arg TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI2_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint32_t tmpccmr1 = 0, tmpccer = 0, tmp = 0;
+
+ /* Disable the Channel 2: Reset the CC2E Bit */
+ TIMx->CCER &= (uint16_t)~TIM_CCER_CC2E;
+ tmpccmr1 = TIMx->CCMR1;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 4);
+
+ /* Select the Input and set the filter */
+ tmpccmr1 &= ((uint32_t)~TIM_CCMR1_CC2S) & ((uint32_t)~TIM_CCMR1_IC2F);
+ tmpccmr1 |= (uint32_t)((uint32_t)TIM_ICFilter << 12);
+ tmpccmr1 |= (uint32_t)((uint32_t)TIM_ICSelection << 8);
+
+ /* Select the Polarity and set the CC2E Bit */
+ tmpccer &= (uint16_t)~(TIM_CCER_CC2P | TIM_CCER_CC2NP);
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC2E);
+
+ /* Write to TIMx CCMR1 and CCER registers */
+ TIMx->CCMR1 = tmpccmr1 ;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI3 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @arg TIM_ICPolarity_BothEdge
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4.
+ * @arg TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI3_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr2 = 0, tmpccer = 0, tmp = 0;
+
+ /* Disable the Channel 3: Reset the CC3E Bit */
+ TIMx->CCER &= (uint16_t)~TIM_CCER_CC3E;
+ tmpccmr2 = TIMx->CCMR2;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 8);
+
+ /* Select the Input and set the filter */
+ tmpccmr2 &= ((uint16_t)~TIM_CCMR1_CC1S) & ((uint16_t)~TIM_CCMR2_IC3F);
+ tmpccmr2 |= (uint16_t)(TIM_ICSelection | (uint16_t)(TIM_ICFilter << (uint16_t)4));
+
+ /* Select the Polarity and set the CC3E Bit */
+ tmpccer &= (uint16_t)~(TIM_CCER_CC3P | TIM_CCER_CC3NP);
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC3E);
+
+ /* Write to TIMx CCMR2 and CCER registers */
+ TIMx->CCMR2 = tmpccmr2;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI4 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @arg TIM_ICPolarity_BothEdge
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3.
+ * @arg TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI4_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr2 = 0, tmpccer = 0, tmp = 0;
+
+ /* Disable the Channel 4: Reset the CC4E Bit */
+ TIMx->CCER &= (uint16_t)~TIM_CCER_CC4E;
+ tmpccmr2 = TIMx->CCMR2;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 12);
+
+ /* Select the Input and set the filter */
+ tmpccmr2 &= ((uint16_t)~TIM_CCMR1_CC2S) & ((uint16_t)~TIM_CCMR1_IC2F);
+ tmpccmr2 |= (uint16_t)(TIM_ICSelection << 8);
+ tmpccmr2 |= (uint16_t)(TIM_ICFilter << 12);
+
+ /* Select the Polarity and set the CC4E Bit */
+ tmpccer &= (uint16_t)~(TIM_CCER_CC4P | TIM_CCER_CC4NP);
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC4E);
+
+ /* Write to TIMx CCMR2 and CCER registers */
+ TIMx->CCMR2 = tmpccmr2;
+ TIMx->CCER = tmpccer ;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/