Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F302R8/stm32f30x_misc.c

Revision:

125:23cc3068a9e4

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F302R8/stm32f30x_misc.c	Wed Mar 19 10:15:22 2014 +0000
@@ -0,0 +1,240 @@
+/**
+  ******************************************************************************
+  * @file    stm32f30x_misc.c
+  * @author  MCD Application Team
+  * @version V1.1.0
+  * @date    27-February-2014
+  * @brief   This file provides all the miscellaneous firmware functions (add-on
+  *          to CMSIS functions).
+  *          
+  @verbatim   
+                               
+ ===============================================================================      
+              ##### How to configure Interrupts using driver #####
+ ===============================================================================      
+    [..] This section provide functions allowing to configure the NVIC interrupts 
+         (IRQ). The Cortex-M4 exceptions are managed by CMSIS functions.
+         (#) Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig()
+             function according to the following table.
+             The table below gives the allowed values of the pre-emption priority 
+             and subpriority according to the Priority Grouping configuration 
+             performed by NVIC_PriorityGroupConfig function.
+         
+         (#) Enable and Configure the priority of the selected IRQ Channels.
+    [..]
+    (@) When the NVIC_PriorityGroup_0 is selected, it will no any nested interrupt,
+        the IRQ priority will be managed only by subpriority.
+        The sub-priority is only used to sort pending exception priorities, 
+        and does not affect active exceptions.
+    (@) Lower priority values gives higher priority.
+    (@) Priority Order:
+        (#@) Lowest Preemption priority.
+        (#@) Lowest Subpriority.
+        (#@) Lowest hardware priority (IRQn position).
+
+  @endverbatim
+
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f30x_misc.h"
+
+/** @addtogroup STM32F30x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup MISC 
+  * @brief MISC driver modules
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+#define AIRCR_VECTKEY_MASK    ((uint32_t)0x05FA0000)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup MISC_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Configures the priority grouping: pre-emption priority and subpriority.
+  * @param  NVIC_PriorityGroup: specifies the priority grouping bits length. 
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority.
+  *                                4 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority.
+  *                                3 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority.
+  *                                2 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority.
+  *                                1 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority.
+  *                                0 bits for subpriority.
+  *     @note When NVIC_PriorityGroup_0 is selected, it will no be any nested 
+  *           interrupt. This interrupts priority is managed only with subpriority.                                    
+  * @retval None
+  */
+void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup));
+  
+  /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */
+  SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup;
+}
+
+/**
+  * @brief  Initializes the NVIC peripheral according to the specified
+  *         parameters in the NVIC_InitStruct.
+  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
+  *         function should be called before. 
+  * @param  NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains
+  *         the configuration information for the specified NVIC peripheral.
+  * @retval None
+  */
+void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)
+{
+  uint32_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F;
+  
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd));
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority));  
+  assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority));
+    
+  if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE)
+  {
+    /* Compute the Corresponding IRQ Priority --------------------------------*/    
+    tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08;
+    tmppre = (0x4 - tmppriority);
+    tmpsub = tmpsub >> tmppriority;
+
+    tmppriority = (uint32_t)NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre;
+    tmppriority |=  NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub;
+    tmppriority = tmppriority << 0x04;
+        
+    NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority;
+    
+    /* Enable the Selected IRQ Channels --------------------------------------*/
+    NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+  else
+  {
+    /* Disable the Selected IRQ Channels -------------------------------------*/
+    NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+}
+
+/**
+  * @brief  Sets the vector table location and Offset.
+  * @param  NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_VectTab_RAM
+  *     @arg NVIC_VectTab_FLASH
+  * @param  Offset: Vector Table base offset field. This value must be a multiple of 0x200.
+  * @retval None
+  */
+void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset)
+{ 
+  /* Check the parameters */
+  assert_param(IS_NVIC_VECTTAB(NVIC_VectTab));
+  assert_param(IS_NVIC_OFFSET(Offset));  
+   
+  SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80);
+}
+
+/**
+  * @brief  Selects the condition for the system to enter low power mode.
+  * @param  LowPowerMode: Specifies the new mode for the system to enter low power mode.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_LP_SEVONPEND
+  *     @arg NVIC_LP_SLEEPDEEP
+  *     @arg NVIC_LP_SLEEPONEXIT
+  * @param  NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_LP(LowPowerMode));
+  assert_param(IS_FUNCTIONAL_STATE(NewState));  
+  
+  if (NewState != DISABLE)
+  {
+    SCB->SCR |= LowPowerMode;
+  }
+  else
+  {
+    SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode);
+  }
+}
+
+/**
+  * @brief  Configures the SysTick clock source.
+  * @param  SysTick_CLKSource: specifies the SysTick clock source.
+  *   This parameter can be one of the following values:
+  *     @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source.
+  *     @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource));
+  if (SysTick_CLKSource == SysTick_CLKSource_HCLK)
+  {
+    SysTick->CTRL |= SysTick_CLKSource_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/