test
来自中国的硬件平台
Dependents: mbed_in_china_blink_led
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/stm32f4xx_hal_adc.c
- Revision:
- 133:d4dda5c437f0
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/stm32f4xx_hal_adc.c Mon Mar 24 17:45:07 2014 +0000
@@ -0,0 +1,1286 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_adc.c
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 18-February-2014
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the Analog to Digital Convertor (ADC) peripheral:
+ * + Initialization and de-initialization functions
+ * + IO operation functions
+ * + State and errors functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### ADC Peripheral features #####
+ ==============================================================================
+ [..]
+ (#) 12-bit, 10-bit, 8-bit or 6-bit configurable resolution.
+ (#) Interrupt generation at the end of conversion, end of injected conversion,
+ and in case of analog watchdog or overrun events
+ (#) Single and continuous conversion modes.
+ (#) Scan mode for automatic conversion of channel 0 to channel x.
+ (#) Data alignment with in-built data coherency.
+ (#) Channel-wise programmable sampling time.
+ (#) External trigger option with configurable polarity for both regular and
+ injected conversion.
+ (#) Dual/Triple mode (on devices with 2 ADCs or more).
+ (#) Configurable DMA data storage in Dual/Triple ADC mode.
+ (#) Configurable delay between conversions in Dual/Triple interleaved mode.
+ (#) ADC conversion type (refer to the datasheets).
+ (#) ADC supply requirements: 2.4 V to 3.6 V at full speed and down to 1.8 V at
+ slower speed.
+ (#) ADC input range: VREF(minus) = VIN = VREF(plus).
+ (#) DMA request generation during regular channel conversion.
+
+
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+ (#)Initialize the ADC low level resources by implementing the HAL_ADC_MspInit():
+ (##) Enable the ADC interface clock using __ADC_CLK_ENABLE()
+ (##) ADC pins configuration
+ (+++) Enable the clock for the ADC GPIOs using the following function:
+ __GPIOx_CLK_ENABLE()
+ (+++) Configure these ADC pins in analog mode using HAL_GPIO_Init()
+ (##) In case of using interrupts (e.g. HAL_ADC_Start_IT())
+ (+++) Configure the ADC interrupt priority using HAL_NVIC_SetPriority()
+ (+++) Enable the ADC IRQ handler using HAL_NVIC_EnableIRQ()
+ (+++) In ADC IRQ handler, call HAL_ADC_IRQHandler()
+ (##) In case of using DMA to control data transfer (e.g. HAL_ADC_Start_DMA())
+ (+++) Enable the DMAx interface clock using __DMAx_CLK_ENABLE()
+ (+++) Configure and enable two DMA streams stream for managing data
+ transfer from peripheral to memory (output stream)
+ (+++) Associate the initilalized DMA handle to the CRYP DMA handle
+ using __HAL_LINKDMA()
+ (+++) Configure the priority and enable the NVIC for the transfer complete
+ interrupt on the two DMA Streams. The output stream should have higher
+ priority than the input stream.
+
+ (#) Configure the ADC Prescaler, conversion resolution and data alignment
+ using the HAL_ADC_Init() function.
+
+ (#) Configure the ADC regular channels group features, use HAL_ADC_Init()
+ and HAL_ADC_ConfigChannel() functions.
+
+ (#) Three mode of operations are available within this driver :
+
+ *** Polling mode IO operation ***
+ =================================
+ [..]
+ (+) Start the ADC peripheral using HAL_ADC_Start()
+ (+) Wait for end of conversion using HAL_ADC_PollForConversion(), at this stage
+ user can specify the value of timeout according to his end application
+ (+) To read the ADC converted values, use the HAL_ADC_GetValue() function.
+ (+) Stop the ADC peripheral using HAL_ADC_Stop()
+
+ *** Interrupt mode IO operation ***
+ ===================================
+ [..]
+ (+) Start the ADC peripheral using HAL_ADC_Start_IT()
+ (+) Use HAL_ADC_IRQHandler() called under ADC_IRQHandler() Interrupt subroutine
+ (+) At ADC end of conversion HAL_ADC_ConvCpltCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_ADC_ConvCpltCallback
+ (+) In case of ADC Error, HAL_ADC_ErrorCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_ADC_ErrorCallback
+ (+) Stop the ADC peripheral using HAL_ADC_Stop_IT()
+
+ *** DMA mode IO operation ***
+ ==============================
+ [..]
+ (+) Start the ADC peripheral using HAL_ADC_Start_DMA(), at this stage the user specify the length
+ of data to be transfered at each end of conversion
+ (+) At The end of data transfer by HAL_ADC_ConvCpltCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_ADC_ConvCpltCallback
+ (+) In case of transfer Error, HAL_ADC_ErrorCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_ADC_ErrorCallback
+ (+) Stop the ADC peripheral using HAL_ADC_Stop_DMA()
+
+ *** ADC HAL driver macros list ***
+ =============================================
+ [..]
+ Below the list of most used macros in ADC HAL driver.
+
+ (+) __HAL_ADC_ENABLE : Enable the ADC peripheral
+ (+) __HAL_ADC_DISABLE : Disable the ADC peripheral
+ (+) __HAL_ADC_ENABLE_IT: Enable the ADC end of conversion interrupt
+ (+) __HAL_ADC_DISABLE_IT: Disable the ADC end of conversion interrupt
+ (+) __HAL_ADC_GET_IT_SOURCE: Check if the specified ADC interrupt source is enabled or disabled
+ (+) __HAL_ADC_CLEAR_FLAG: Clear the ADC's pending flags
+ (+) __HAL_ADC_GET_FLAG: Get the selected ADC's flag status
+ (+) __HAL_ADC_GET_RESOLUTION: Return resolution bits in CR1 register
+
+ [..]
+ (@) You can refer to the ADC HAL driver header file for more useful macros
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup ADC
+ * @brief ADC driver modules
+ * @{
+ */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+static void ADC_Init(ADC_HandleTypeDef* hadc);
+static void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma);
+static void ADC_DMAError(DMA_HandleTypeDef *hdma);
+static void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma);
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup ADC_Private_Functions
+ * @{
+ */
+
+/** @defgroup ADC_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Initialize and configure the ADC.
+ (+) De-initialize the ADC.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initializes the ADCx peripheral according to the specified parameters
+ * in the ADC_InitStruct and initializes the ADC MSP.
+ *
+ * @note This function is used to configure the global features of the ADC (
+ * ClockPrescaler, Resolution, Data Alignment and number of conversion), however,
+ * the rest of the configuration parameters are specific to the regular
+ * channels group (scan mode activation, continuous mode activation,
+ * External trigger source and edge, DMA continuous request after the
+ * last transfer and End of conversion selection).
+ *
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef* hadc)
+{
+ /* Check ADC handle */
+ if(hadc == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_ADC_CLOCKPRESCALER(hadc->Init.ClockPrescaler));
+ assert_param(IS_ADC_RESOLUTION(hadc->Init.Resolution));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ScanConvMode));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
+ assert_param(IS_ADC_EXT_TRIG(hadc->Init.ExternalTrigConv));
+ assert_param(IS_ADC_DATA_ALIGN(hadc->Init.DataAlign));
+ assert_param(IS_ADC_REGULAR_LENGTH(hadc->Init.NbrOfConversion));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DMAContinuousRequests));
+ assert_param(IS_ADC_EOCSelection(hadc->Init.EOCSelection));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DiscontinuousConvMode));
+
+ if(hadc->State == HAL_ADC_STATE_RESET)
+ {
+ /* Init the low level hardware */
+ HAL_ADC_MspInit(hadc);
+ }
+
+ /* Initialize the ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY;
+
+ /* Set ADC parameters */
+ ADC_Init(hadc);
+
+ /* Set ADC error code to none */
+ hadc->ErrorCode = HAL_ADC_ERROR_NONE;
+
+ /* Initialize the ADC state */
+ hadc->State = HAL_ADC_STATE_READY;
+
+ /* Release Lock */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Deinitializes the ADCx peripheral registers to their default reset values.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef* hadc)
+{
+ /* Check ADC handle */
+ if(hadc == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY;
+
+ /* DeInit the low level hardware */
+ HAL_ADC_MspDeInit(hadc);
+
+ /* Set ADC error code to none */
+ hadc->ErrorCode = HAL_ADC_ERROR_NONE;
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_RESET;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the ADC MSP.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief DeInitializes the ADC MSP.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_MspDeInit could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Group2 IO operation functions
+ * @brief IO operation functions
+ *
+@verbatim
+ ===============================================================================
+ ##### IO operation functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Start conversion of regular channel.
+ (+) Stop conversion of regular channel.
+ (+) Start conversion of regular channel and enable interrupt.
+ (+) Stop conversion of regular channel and disable interrupt.
+ (+) Start conversion of regular channel and enable DMA transfer.
+ (+) Stop conversion of regular channel and disable DMA transfer.
+ (+) Handle ADC interrupt request.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables ADC and starts conversion of the regular channels.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef* hadc)
+{
+ uint16_t i = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Check if an injected conversion is ongoing */
+ if(hadc->State == HAL_ADC_STATE_BUSY_INJ)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY_REG;
+ }
+
+ /* Check if ADC peripheral is disabled in order to enable it and wait during
+ Tstab time the ADC's stabilization */
+ if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
+ {
+ /* Enable the Peripheral */
+ __HAL_ADC_ENABLE(hadc);
+
+ /* Delay inserted to wait during Tstab time the ADC's stabilazation */
+ for(; i <= 540; i++)
+ {
+ __NOP();
+ }
+ }
+
+ /* Check if Multimode enabled */
+ if(HAL_IS_BIT_CLR(ADC->CCR, ADC_CCR_MULTI))
+ {
+ /* if no external trigger present enable software conversion of regular channels */
+ if(hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE)
+ {
+ /* Enable the selected ADC software conversion for regular group */
+ hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
+ }
+ }
+ else
+ {
+ /* if instance of handle correspond to ADC1 and no external trigger present enable software conversion of regular channels */
+ if((hadc->Instance == ADC1) && (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE))
+ {
+ /* Enable the selected ADC software conversion for regular group */
+ hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
+ }
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Disables ADC and stop conversion of regular channels.
+ *
+ * @note Caution: This function will stop also injected channels.
+ *
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * last transfer and End of conversion selection).
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef* hadc)
+{
+ /* Disable the Peripheral */
+ __HAL_ADC_DISABLE(hadc);
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Poll for regular conversion complete
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @param Timeout: Timeout value in millisecond.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout)
+{
+ uint32_t timeout;
+
+ /* Get timeout */
+ timeout = HAL_GetTick() + Timeout;
+
+ /* Check End of conversion flag */
+ while(!(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOC)))
+ {
+ /* Check for the Timeout */
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if(HAL_GetTick() >= timeout)
+ {
+ hadc->State= HAL_ADC_STATE_TIMEOUT;
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Check if an injected conversion is ready */
+ if(hadc->State == HAL_ADC_STATE_EOC_INJ)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_REG;
+ }
+
+ /* Return ADC state */
+ return HAL_OK;
+}
+
+/**
+ * @brief Poll for conversion event
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @param EventType: the ADC event type.
+ * This parameter can be one of the following values:
+ * @arg AWD_EVENT: ADC Analog watch Dog event.
+ * @arg OVR_EVENT: ADC Overrun event.
+ * @param Timeout: Timeout value in millisecond.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef* hadc, uint32_t EventType, uint32_t Timeout)
+{
+ /* Check the parameters */
+ assert_param(IS_ADC_EVENT_TYPE(EventType));
+
+ uint32_t timeout;
+
+ /* Get timeout */
+ timeout = HAL_GetTick() + Timeout;
+
+ /* Check selected event flag */
+ while(!(__HAL_ADC_GET_FLAG(hadc,EventType)))
+ {
+ /* Check for the Timeout */
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if(HAL_GetTick() >= timeout)
+ {
+ hadc->State= HAL_ADC_STATE_TIMEOUT;
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Check analog watchdog flag */
+ if(EventType == AWD_EVENT)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_AWD;
+
+ /* Clear the ADCx's analog watchdog flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_AWD);
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_ERROR;
+
+ /* Clear the ADCx's Overrun flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_OVR);
+ }
+
+ /* Return ADC state */
+ return HAL_OK;
+}
+
+
+/**
+ * @brief Enables the interrupt and starts ADC conversion of regular channels.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc)
+{
+ uint16_t i = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Check if an injected conversion is ongoing */
+ if(hadc->State == HAL_ADC_STATE_BUSY_INJ)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY_REG;
+ }
+
+ /* Set ADC error code to none */
+ hadc->ErrorCode = HAL_ADC_ERROR_NONE;
+
+ /* Check if ADC peripheral is disabled in order to enable it and wait during
+ Tstab time the ADC's stabilization */
+ if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
+ {
+ /* Enable the Peripheral */
+ __HAL_ADC_ENABLE(hadc);
+
+ /* Delay inserted to wait during Tstab time the ADC's stabilazation */
+ for(; i <= 540; i++)
+ {
+ __NOP();
+ }
+ }
+
+ /* Enable the ADC overrun interrupt */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
+
+ /* Enable the ADC end of conversion interrupt for regular group */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_EOC);
+
+ /* Check if Multimode enabled */
+ if(HAL_IS_BIT_CLR(ADC->CCR, ADC_CCR_MULTI))
+ {
+ /* if no externel trigger present enable software conversion of regular channels */
+ if (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE)
+ {
+ /* Enable the selected ADC software conversion for regular group */
+ hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
+ }
+ }
+ else
+ {
+ /* if instance of handle correspond to ADC1 and no external trigger present enable software conversion of regular channels */
+ if ((hadc->Instance == (ADC_TypeDef*)0x40012000) && (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE))
+ {
+ /* Enable the selected ADC software conversion for regular group */
+ hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
+ }
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Disables the interrupt and stop ADC conversion of regular channels.
+ *
+ * @note Caution: This function will stop also injected channels.
+ *
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef* hadc)
+{
+ /* Disable the ADC end of conversion interrupt for regular group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
+
+ /* Disable the ADC end of conversion interrupt for injected group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_CR1_JEOCIE);
+
+ /* Enable the Periphral */
+ __HAL_ADC_DISABLE(hadc);
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Handles ADC interrupt request
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+void HAL_ADC_IRQHandler(ADC_HandleTypeDef* hadc)
+{
+ uint32_t tmp1 = 0, tmp2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_REGULAR_LENGTH(hadc->Init.NbrOfConversion));
+ assert_param(IS_ADC_EOCSelection(hadc->Init.EOCSelection));
+
+ tmp1 = __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOC);
+ tmp2 = __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_EOC);
+ /* Check End of conversion flag for regular channels */
+ if(tmp1 && tmp2)
+ {
+ /* Check if an injected conversion is ready */
+ if(hadc->State == HAL_ADC_STATE_EOC_INJ)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_REG;
+ }
+
+ if((hadc->Init.ContinuousConvMode == DISABLE) && (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE))
+ {
+ if(hadc->Init.EOCSelection == EOC_SEQ_CONV)
+ {
+ /* DISABLE the ADC end of conversion interrupt for regular group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
+
+ /* DISABLE the ADC overrun interrupt */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_OVR);
+ }
+ else
+ {
+ if (hadc->NbrOfCurrentConversionRank == 0)
+ {
+ hadc->NbrOfCurrentConversionRank = hadc->Init.NbrOfConversion;
+ }
+
+ /* Decrement the number of conversion when an interrupt occurs */
+ hadc->NbrOfCurrentConversionRank--;
+
+ /* Check if all conversions are finished */
+ if(hadc->NbrOfCurrentConversionRank == 0)
+ {
+ /* DISABLE the ADC end of conversion interrupt for regular group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
+
+ /* DISABLE the ADC overrun interrupt */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_OVR);
+ }
+ }
+ }
+
+ /* Conversion complete callback */
+ HAL_ADC_ConvCpltCallback(hadc);
+
+ /* Clear the ADCx flag for regular end of conversion */
+ __HAL_ADC_CLEAR_FLAG(hadc,ADC_FLAG_EOC);
+ }
+
+ tmp1 = __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_JEOC);
+ tmp2 = __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_JEOC);
+ /* Check End of conversion flag for injected channels */
+ if(tmp1 && tmp2)
+ {
+ /* Check if a regular conversion is ready */
+ if(hadc->State == HAL_ADC_STATE_EOC_REG)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_INJ;
+ }
+
+ tmp1 = HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO);
+ tmp2 = HAL_IS_BIT_CLR(hadc->Instance->CR2, ADC_CR2_JEXTEN);
+ if(((hadc->Init.ContinuousConvMode == DISABLE) || tmp1) && tmp2)
+ {
+ /* DISABLE the ADC end of conversion interrupt for injected group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_JEOC);
+ }
+
+ /* Conversion complete callback */
+ HAL_ADCEx_InjectedConvCpltCallback(hadc);
+
+ /* Clear the ADCx flag for injected end of conversion */
+ __HAL_ADC_CLEAR_FLAG(hadc,ADC_FLAG_JEOC);
+ }
+
+ tmp1 = __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_AWD);
+ tmp2 = __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_AWD);
+ /* Check Analog watchdog flag */
+ if(tmp1 && tmp2)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_AWD;
+
+ /* Clear the ADCx's Analog watchdog flag */
+ __HAL_ADC_CLEAR_FLAG(hadc,ADC_FLAG_AWD);
+
+ /* Level out of window callback */
+ HAL_ADC_LevelOutOfWindowCallback(hadc);
+ }
+
+ tmp1 = __HAL_ADC_GET_FLAG(hadc, ADC_FLAG_OVR);
+ tmp2 = __HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_OVR);
+ /* Check Overrun flag */
+ if(tmp1 && tmp2)
+ {
+ /* Change ADC state to overrun state */
+ hadc->State = HAL_ADC_STATE_ERROR;
+
+ /* Set ADC error code to overrun */
+ hadc->ErrorCode |= HAL_ADC_ERROR_OVR;
+
+ /* Clear the Overrun flag */
+ __HAL_ADC_CLEAR_FLAG(hadc,ADC_FLAG_OVR);
+
+ /* Error callback */
+ HAL_ADC_ErrorCallback(hadc);
+ }
+}
+
+/**
+ * @brief Enables ADC DMA request after last transfer (Single-ADC mode) and enables ADC peripheral
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @param pData: The destination Buffer address.
+ * @param Length: The length of data to be transferred from ADC peripheral to memory.
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
+{
+ uint16_t i = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Enable ADC overrun interrupt */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
+
+ /* Enable ADC DMA mode */
+ hadc->Instance->CR2 |= ADC_CR2_DMA;
+
+ /* Set the DMA transfer complete callback */
+ hadc->DMA_Handle->XferCpltCallback = ADC_DMAConvCplt;
+
+ /* Set the DMA half transfer complete callback */
+ hadc->DMA_Handle->XferHalfCpltCallback = ADC_DMAHalfConvCplt;
+
+ /* Set the DMA error callback */
+ hadc->DMA_Handle->XferErrorCallback = ADC_DMAError ;
+
+ /* Enable the DMA Stream */
+ HAL_DMA_Start_IT(hadc->DMA_Handle, (uint32_t)&hadc->Instance->DR, (uint32_t)pData, Length);
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_BUSY_REG;
+
+ /* Check if ADC peripheral is disabled in order to enable it and wait during
+ Tstab time the ADC's stabilization */
+ if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
+ {
+ /* Enable the Peripheral */
+ __HAL_ADC_ENABLE(hadc);
+
+ /* Delay inserted to wait during Tstab time the ADC's stabilazation */
+ for(; i <= 540; i++)
+ {
+ __NOP();
+ }
+ }
+
+ /* if no external trigger present enable software conversion of regular channels */
+ if (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE)
+ {
+ /* Enable the selected ADC software conversion for regular group */
+ hadc->Instance->CR2 |= ADC_CR2_SWSTART;
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Disables ADC DMA (Single-ADC mode) and disables ADC peripheral
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef* hadc)
+{
+ /* Disable the Periphral */
+ __HAL_ADC_DISABLE(hadc);
+
+ /* Disable ADC overrun interrupt */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_OVR);
+
+ /* Disable the selected ADC DMA mode */
+ hadc->Instance->CR2 &= ~ADC_CR2_DMA;
+
+ /* Disable the ADC DMA Stream */
+ HAL_DMA_Abort(hadc->DMA_Handle);
+
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Gets the converted value from data register of regular channel.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval Converted value
+ */
+uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef* hadc)
+{
+ /* Return the selected ADC converted value */
+ return hadc->Instance->DR;
+}
+
+/**
+ * @brief Regular conversion complete callback in non blocking mode
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_ConvCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Regular conversion half DMA transfer callback in non blocking mode
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef* hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_ConvHalfCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Analog watchdog callback in non blocking mode
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef* hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_LevelOoutOfWindowCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Error ADC callback.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+__weak void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_ADC_ErrorCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Group3 Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Configure regular channels.
+ (+) Configure injected channels.
+ (+) Configure multimode.
+ (+) Configure the analog watch dog.
+
+@endverbatim
+ * @{
+ */
+
+ /**
+ * @brief Configures for the selected ADC regular channel its corresponding
+ * rank in the sequencer and its sample time.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @param sConfig: ADC configuration structure.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig)
+{
+ /* Check the parameters */
+ assert_param(IS_ADC_CHANNEL(sConfig->Channel));
+ assert_param(IS_ADC_REGULAR_RANK(sConfig->Rank));
+ assert_param(IS_ADC_SAMPLE_TIME(sConfig->SamplingTime));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* if ADC_Channel_10 ... ADC_Channel_18 is selected */
+ if (sConfig->Channel > ADC_CHANNEL_9)
+ {
+ /* Clear the old sample time */
+ hadc->Instance->SMPR1 &= ~__HAL_ADC_SMPR1(ADC_SMPR1_SMP10, sConfig->Channel);
+
+ /* Set the new sample time */
+ hadc->Instance->SMPR1 |= __HAL_ADC_SMPR1(sConfig->SamplingTime, sConfig->Channel);
+ }
+ else /* ADC_Channel include in ADC_Channel_[0..9] */
+ {
+ /* Clear the old sample time */
+ hadc->Instance->SMPR2 &= ~__HAL_ADC_SMPR2(ADC_SMPR2_SMP0, sConfig->Channel);
+
+ /* Set the new sample time */
+ hadc->Instance->SMPR2 |= __HAL_ADC_SMPR2(sConfig->SamplingTime, sConfig->Channel);
+ }
+
+ /* For Rank 1 to 6 */
+ if (sConfig->Rank < 7)
+ {
+ /* Clear the old SQx bits for the selected rank */
+ hadc->Instance->SQR3 &= ~__HAL_ADC_SQR3_RK(ADC_SQR3_SQ1, sConfig->Rank);
+
+ /* Set the SQx bits for the selected rank */
+ hadc->Instance->SQR3 |= __HAL_ADC_SQR3_RK(sConfig->Channel, sConfig->Rank);
+ }
+ /* For Rank 7 to 12 */
+ else if (sConfig->Rank < 13)
+ {
+ /* Clear the old SQx bits for the selected rank */
+ hadc->Instance->SQR2 &= ~__HAL_ADC_SQR2_RK(ADC_SQR2_SQ7, sConfig->Rank);
+
+ /* Set the SQx bits for the selected rank */
+ hadc->Instance->SQR2 |= __HAL_ADC_SQR2_RK(sConfig->Channel, sConfig->Rank);
+ }
+ /* For Rank 13 to 16 */
+ else
+ {
+ /* Clear the old SQx bits for the selected rank */
+ hadc->Instance->SQR1 &= ~__HAL_ADC_SQR1_RK(ADC_SQR1_SQ13, sConfig->Rank);
+
+ /* Set the SQx bits for the selected rank */
+ hadc->Instance->SQR1 |= __HAL_ADC_SQR1_RK(sConfig->Channel, sConfig->Rank);
+ }
+
+ /* if ADC1 Channel_18 is selected enable VBAT Channel */
+ if ((hadc->Instance == ADC1) && (sConfig->Channel == ADC_CHANNEL_VBAT))
+ {
+ /* Enable the VBAT channel*/
+ ADC->CCR |= ADC_CCR_VBATE;
+ }
+
+ /* if ADC1 Channel_16 or Channel_17 is selected enable TSVREFE Channel(Temperature sensor and VREFINT) */
+ if ((hadc->Instance == ADC1) && ((sConfig->Channel == ADC_CHANNEL_TEMPSENSOR) || (sConfig->Channel == ADC_CHANNEL_VREFINT)))
+ {
+ /* Enable the TSVREFE channel*/
+ ADC->CCR |= ADC_CCR_TSVREFE;
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the analog watchdog.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @param AnalogWDGConfig : pointer to an ADC_AnalogWDGConfTypeDef structure
+ * that contains the configuration information of ADC analog watchdog.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig)
+{
+#ifdef USE_FULL_ASSERT
+ uint32_t tmp = 0;
+#endif /* USE_FULL_ASSERT */
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ANALOG_WATCHDOG(AnalogWDGConfig->WatchdogMode));
+ assert_param(IS_ADC_CHANNEL(AnalogWDGConfig->Channel));
+ assert_param(IS_FUNCTIONAL_STATE(AnalogWDGConfig->ITMode));
+
+#ifdef USE_FULL_ASSERT
+ tmp = __HAL_ADC_GET_RESOLUTION(hadc);
+ assert_param(IS_ADC_RANGE(tmp, AnalogWDGConfig->HighThreshold));
+ assert_param(IS_ADC_RANGE(tmp, AnalogWDGConfig->LowThreshold));
+#endif /* USE_FULL_ASSERT */
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ if(AnalogWDGConfig->ITMode == ENABLE)
+ {
+ /* Enable the ADC Analog watchdog interrupt */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_AWD);
+ }
+ else
+ {
+ /* Disable the ADC Analog watchdog interrupt */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_AWD);
+ }
+
+ /* Clear AWDEN, JAWDEN and AWDSGL bits */
+ hadc->Instance->CR1 &= ~(ADC_CR1_AWDSGL | ADC_CR1_JAWDEN | ADC_CR1_AWDEN);
+
+ /* Set the analog watchdog enable mode */
+ hadc->Instance->CR1 |= AnalogWDGConfig->WatchdogMode;
+
+ /* Set the high threshold */
+ hadc->Instance->HTR = AnalogWDGConfig->HighThreshold;
+
+ /* Set the low threshold */
+ hadc->Instance->LTR = AnalogWDGConfig->LowThreshold;
+
+ /* Clear the Analog watchdog channel select bits */
+ hadc->Instance->CR1 &= ~ADC_CR1_AWDCH;
+
+ /* Set the Analog watchdog channel */
+ hadc->Instance->CR1 |= AnalogWDGConfig->Channel;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Group4 ADC Peripheral State functions
+ * @brief ADC Peripheral State functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral State and errors functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions allowing to
+ (+) Check the ADC state
+ (+) Check the ADC Error
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief return the ADC state
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval HAL state
+ */
+HAL_ADC_StateTypeDef HAL_ADC_GetState(ADC_HandleTypeDef* hadc)
+{
+ /* Return ADC state */
+ return hadc->State;
+}
+
+/**
+ * @brief Return the ADC error code
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval ADC Error Code
+ */
+uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc)
+{
+ return hadc->ErrorCode;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @brief Initializes the ADCx peripheral according to the specified parameters
+ * in the ADC_InitStruct without initializing the ADC MSP.
+ * @param hadc: pointer to a ADC_HandleTypeDef structure that contains
+ * the configuration information for the specified ADC.
+ * @retval None
+ */
+static void ADC_Init(ADC_HandleTypeDef* hadc)
+{
+
+ /* Set ADC parameters */
+ /* Set the ADC clock prescaler */
+ ADC->CCR &= ~(ADC_CCR_ADCPRE);
+ ADC->CCR |= hadc->Init.ClockPrescaler;
+
+ /* Set ADC scan mode */
+ hadc->Instance->CR1 &= ~(ADC_CR1_SCAN);
+ hadc->Instance->CR1 |= __HAL_ADC_CR1_SCANCONV(hadc->Init.ScanConvMode);
+
+ /* Set ADC resolution */
+ hadc->Instance->CR1 &= ~(ADC_CR1_RES);
+ hadc->Instance->CR1 |= hadc->Init.Resolution;
+
+ /* Set ADC data alignment */
+ hadc->Instance->CR2 &= ~(ADC_CR2_ALIGN);
+ hadc->Instance->CR2 |= hadc->Init.DataAlign;
+
+ /* Select external trigger to start conversion */
+ hadc->Instance->CR2 &= ~(ADC_CR2_EXTSEL);
+ hadc->Instance->CR2 |= hadc->Init.ExternalTrigConv;
+
+ /* Select external trigger polarity */
+ hadc->Instance->CR2 &= ~(ADC_CR2_EXTEN);
+ hadc->Instance->CR2 |= hadc->Init.ExternalTrigConvEdge;
+
+ /* Enable or disable ADC continuous conversion mode */
+ hadc->Instance->CR2 &= ~(ADC_CR2_CONT);
+ hadc->Instance->CR2 |= __HAL_ADC_CR2_CONTINUOUS(hadc->Init.ContinuousConvMode);
+
+ if (hadc->Init.DiscontinuousConvMode != DISABLE)
+ {
+ assert_param(IS_ADC_REGULAR_DISC_NUMBER(hadc->Init.NbrOfDiscConversion));
+
+ /* Enable the selected ADC regular discontinuous mode */
+ hadc->Instance->CR1 |= (uint32_t)ADC_CR1_DISCEN;
+
+ /* Set the number of channels to be converted in discontinuous mode */
+ hadc->Instance->CR1 &= ~(ADC_CR1_DISCNUM);
+ hadc->Instance->CR1 |= __HAL_ADC_CR1_DISCONTINUOUS(hadc->Init.NbrOfDiscConversion);
+ }
+ else
+ {
+ /* Disable the selected ADC regular discontinuous mode */
+ hadc->Instance->CR1 &= ~(ADC_CR1_DISCEN);
+ }
+
+ /* Set ADC number of conversion */
+ hadc->Instance->SQR1 &= ~(ADC_SQR1_L);
+ hadc->Instance->SQR1 |= __HAL_ADC_SQR1(hadc->Init.NbrOfConversion);
+
+ /* Enable or disable ADC DMA continuous request */
+ hadc->Instance->CR2 &= ~(ADC_CR2_DDS);
+ hadc->Instance->CR2 |= __HAL_ADC_CR2_DMAContReq(hadc->Init.DMAContinuousRequests);
+
+ /* Enable or disable ADC end of conversion selection */
+ hadc->Instance->CR2 &= ~(ADC_CR2_EOCS);
+ hadc->Instance->CR2 |= __HAL_ADC_CR2_EOCSelection(hadc->Init.EOCSelection);
+}
+
+/**
+ * @brief DMA transfer complete callback.
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+static void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma)
+{
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+ /* Check if an injected conversion is ready */
+ if(hadc->State == HAL_ADC_STATE_EOC_INJ)
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_INJ_REG;
+ }
+ else
+ {
+ /* Change ADC state */
+ hadc->State = HAL_ADC_STATE_EOC_REG;
+ }
+
+ HAL_ADC_ConvCpltCallback(hadc);
+}
+
+/**
+ * @brief DMA half transfer complete callback.
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+static void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma)
+{
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+ /* Conversion complete callback */
+ HAL_ADC_ConvHalfCpltCallback(hadc);
+}
+
+/**
+ * @brief DMA error callback
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+static void ADC_DMAError(DMA_HandleTypeDef *hdma)
+{
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+ hadc->State= HAL_ADC_STATE_ERROR;
+ /* Set ADC error code to DMA error */
+ hadc->ErrorCode |= HAL_ADC_ERROR_DMA;
+ HAL_ADC_ErrorCallback(hadc);
+}
+
+
+/**
+ * @}
+ */
+
+#endif /* HAL_ADC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/