james kain
JEK changes enabling proper recording of IMU/GPS datastrams - 02-APR-2013
Fork of
GPS_Incremental
by 
Dan Matthews
Revision 0:c746ee34feae, committed 2013-03-19
- Comitter:
- dannyman939
- Date:
- Tue Mar 19 02:17:40 2013 +0000
- Child:
- 1:cbb9104d826f
- Commit message:
- Basic functionality, Chris Version 0.0
Changed in this revision
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/ADIS16488.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,91 @@
+
+
+
+//set up the SPI on pins 5, 6, 7 to read from the ADIS16488
+SPI spi(p5, p6, p7); // mosi (DIN), miso (DOUT), sclk (CLK)
+DigitalOut ADIS_CS(p8); //Chip Select for the ADIS SPI
+InterruptIn ADIS_DR(p28); //DataReady interrupt connected to DIO2 for ADIS
+DigitalOut ADIS_RST(p20); //ADIS reset pin
+
+bool IMUDataReady = false;
+int IMURecordCounter = 0;
+//see Table 9 from page 11 of the ADIS16488 spec
+//see fig 15 of spec -- note the low byte of the regsiter word is always zero
+// X_DELTANG_LOW, Y_DELTANG_LOW, X_DETANG_LOW, X_DELTVEL_LOW, Y_DELTVEL_LOW, Z_DELTVEL_LOW
+unsigned short LOW_REGISTER[] = {0x4000, 0x4400, 0x4800, 0x4C00, 0x5000, 0x5400};
+// X_DELTANG_HIGH, Y_DELTANG_HIGH, X_DETANG_HIGH, X_DELTVEL_HIGH, Y_DELTVEL_HIGH, Z_DELTVEL_HIGH
+unsigned short HIGH_REGISTER[] = {0x4200, 0x4600, 0x4A00, 0x4E00, 0x5200, 0x5600};
+
+union WD { long dataWord; unsigned short pt[2];} wd;
+
+#pragma pack(1)
+struct IMUREC
+{
+ unsigned long synch;
+ unsigned char msgID;
+ double GPSTime;
+ long dataWord[6];
+} imuRec;
+
+
+
+void IMUDataReadyISR(void)
+{
+ imuRec.GPSTime = GPSTimemsecs + timeFromPPS.read_us()/1000000.0;
+ spi.write((int) HIGH_REGISTER[0]); // next read will return results from HIGH_REGITER[0]
+ for (int i=0; i<6; i++) //read the 6 rate and accel variables
+ {
+ wd.pt[1] = (unsigned short)spi.write((int) LOW_REGISTER[i]) ;
+ if (i<5) // dont this on the last because this was pre-called
+ {
+ wd.pt[0] = (unsigned short)spi.write((int) HIGH_REGISTER[i+1]);
+ }
+ imuRec.dataWord[i] = wd.dataWord; //data word is a signed long
+
+ }
+ IMUDataReady = true;
+ IMURecordCounter++;
+
+ return;
+}
+
+void setupADIS(void)
+{
+ ADIS_DR.mode(PullDown);
+ ADIS_RST = 0;
+
+ printf("\nStart of ADIS test\n");
+ // set the IMU dataReady ISR
+ ADIS_DR.rise(&IMUDataReadyISR);
+
+ // Setup the mbed SPI for 16 bit data, high steady state clock,
+ // second edge capture, with a 1MHz clock rate
+ spi.format(16,3);
+ spi.frequency(1000000);
+
+ ADIS_CS = 1; //CS must be set high before it goes low cause the enable is the transition
+ ADIS_RST = 1;
+ wait(0.5);
+ ADIS_CS = 0; //set the Chip select low to enable the IMU SPI access
+
+ spi.write((int)0x8003); //change to page 3
+
+ //change the DECRATE to 98.4 Hz (this is also in page 3)
+ //the 8 sets the high bit to 1 indicating a write to a register
+ // The C abd D designate the registers for the DECRATE of Page 3
+ // The 17 sets the rate to: 2460/(23+1) = 102.5Hz
+ spi.write((int)0x8C17); //write high byte (only page number can be written in a single byte)
+ spi.write((int)0x8D00); //write the low byte of DECRATE
+
+ //to set the GPS VARF clock as the input synch clock for the IMU
+ //the high byte is CD indicating the synch is enabled on the rising edge of the input clock
+ //spi.write((int)0x86CD); //write high byte to register 0x06
+ //spi.write((int)0x8700); //write the low byte of 00 to registed 0x07
+
+ //change the page to 0 to get the data
+ spi.write((int)0x8000); //change to page 0
+
+ //set the IMU synch and message ID
+ imuRec.synch = 0xAA44121C; //same as the GPS synch words
+ imuRec.msgID=111; //IMU record ID
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATDirHandle.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,66 @@
+/* mbed Microcontroller Library - FATDirHandle
+ * Copyright (c) 2008, sford
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include "ff.h"
+#include "FATDirHandle.h"
+#include "FATFileSystem.h"
+
+namespace mbed {
+
+FATDirHandle::FATDirHandle(const FATFS_DIR &the_dir) {
+ dir = the_dir;
+}
+
+int FATDirHandle::closedir() {
+ delete this;
+ return 0;
+}
+
+struct dirent *FATDirHandle::readdir() {
+ FILINFO finfo;
+
+#if _USE_LFN
+ finfo.lfname = cur_entry.d_name;
+ finfo.lfsize = sizeof(cur_entry.d_name);
+#endif // _USE_LFN
+
+ FRESULT res = f_readdir(&dir, &finfo);
+
+#if _USE_LFN
+ if(res != 0 || finfo.fname[0]==0) {
+ return NULL;
+ } else {
+ if(cur_entry.d_name[0]==0) {
+ // No long filename so use short filename.
+ memcpy(cur_entry.d_name, finfo.fname, sizeof(finfo.fname));
+ }
+ return &cur_entry;
+ }
+#else
+ if(res != 0 || finfo.fname[0]==0) {
+ return NULL;
+ } else {
+ memcpy(cur_entry.d_name, finfo.fname, sizeof(finfo.fname));
+ return &cur_entry;
+ }
+#endif /* _USE_LFN */
+}
+
+void FATDirHandle::rewinddir() {
+ dir.index = 0;
+}
+
+off_t FATDirHandle::telldir() {
+ return dir.index;
+}
+
+void FATDirHandle::seekdir(off_t location) {
+ dir.index = location;
+}
+
+}
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATDirHandle.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,31 @@
+/* mbed Microcontroller Library - FATDirHandle
+ * Copyright (c) 2008, sford
+ */
+
+#ifndef MBED_FATDIRHANDLE_H
+#define MBED_FATDIRHANDLE_H
+
+#include "DirHandle.h"
+#include "ff.h"
+
+namespace mbed {
+
+class FATDirHandle : public DirHandle {
+
+ public:
+ FATDirHandle(const FATFS_DIR &the_dir);
+ virtual int closedir();
+ virtual struct dirent *readdir();
+ virtual void rewinddir();
+ virtual off_t telldir();
+ virtual void seekdir(off_t location);
+
+ private:
+ FATFS_DIR dir;
+ struct dirent cur_entry;
+
+};
+
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATFileHandle.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,102 @@
+/* mbed Microcontroller Library - FATFileHandle
+ * Copyright (c) 2008, sford
+ */
+
+#include "FATFileHandle.h"
+
+#include <stdio.h>
+#include <stdlib.h>
+#include "ff.h"
+#include "FATFileSystem.h"
+
+namespace mbed {
+
+#if FFSDEBUG_ENABLED
+static const char *FR_ERRORS[] = {
+ "FR_OK = 0",
+ "FR_NOT_READY",
+ "FR_NO_FILE",
+ "FR_NO_PATH",
+ "FR_INVALID_NAME",
+ "FR_INVALID_DRIVE",
+ "FR_DENIED",
+ "FR_EXIST",
+ "FR_RW_ERROR",
+ "FR_WRITE_PROTECTED",
+ "FR_NOT_ENABLED",
+ "FR_NO_FILESYSTEM",
+ "FR_INVALID_OBJECT",
+ "FR_MKFS_ABORTED"
+};
+#endif
+
+FATFileHandle::FATFileHandle(FIL fh) {
+ _fh = fh;
+}
+
+int FATFileHandle::close() {
+ FFSDEBUG("close\n");
+ int retval = f_close(&_fh);
+ delete this;
+ return retval;
+}
+
+ssize_t FATFileHandle::write(const void* buffer, size_t length) {
+ FFSDEBUG("write(%d)\n", length);
+ UINT n;
+ FRESULT res = f_write(&_fh, buffer, length, &n);
+ if(res) {
+ FFSDEBUG("f_write() failed (%d, %s)", res, FR_ERRORS[res]);
+ return -1;
+ }
+ return n;
+}
+
+ssize_t FATFileHandle::read(void* buffer, size_t length) {
+ FFSDEBUG("read(%d)\n", length);
+ UINT n;
+ FRESULT res = f_read(&_fh, buffer, length, &n);
+ if(res) {
+ FFSDEBUG("f_read() failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return -1;
+ }
+ return n;
+}
+
+int FATFileHandle::isatty() {
+ return 0;
+}
+
+off_t FATFileHandle::lseek(off_t position, int whence) {
+ FFSDEBUG("lseek(%i,%i)\n",position,whence);
+ if(whence == SEEK_END) {
+ position += _fh.fsize;
+ } else if(whence==SEEK_CUR) {
+ position += _fh.fptr;
+ }
+ FRESULT res = f_lseek(&_fh, position);
+ if(res) {
+ FFSDEBUG("lseek failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return -1;
+ } else {
+ FFSDEBUG("lseek OK, returning %i\n", _fh.fptr);
+ return _fh.fptr;
+ }
+}
+
+int FATFileHandle::fsync() {
+ FFSDEBUG("fsync()\n");
+ FRESULT res = f_sync(&_fh);
+ if (res) {
+ FFSDEBUG("f_sync() failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return -1;
+ }
+ return 0;
+}
+
+off_t FATFileHandle::flen() {
+ FFSDEBUG("flen\n");
+ return _fh.fsize;
+}
+
+} // namespace mbed
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATFileHandle.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,33 @@
+/* mbed Microcontroller Library - FATFileHandle
+ * Copyright (c) 2008, sford
+ */
+
+#ifndef MBED_FATFILEHANDLE_H
+#define MBED_FATFILEHANDLE_H
+
+#include "FileHandle.h"
+#include "ff.h"
+
+namespace mbed {
+
+class FATFileHandle : public FileHandle {
+public:
+
+ FATFileHandle(FIL fh);
+ virtual int close();
+ virtual ssize_t write(const void* buffer, size_t length);
+ virtual ssize_t read(void* buffer, size_t length);
+ virtual int isatty();
+ virtual off_t lseek(off_t position, int whence);
+ virtual int fsync();
+ virtual off_t flen();
+
+protected:
+
+ FIL _fh;
+
+};
+
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATFileSystem.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,134 @@
+/* mbed Microcontroller Library - FATFileSystem
+ * Copyright (c) 2008, sford
+ */
+
+#include "FATFileSystem.h"
+
+#include "mbed.h"
+
+#include "FileSystemLike.h"
+#include "FATFileHandle.h"
+#include "FATDirHandle.h"
+#include "ff.h"
+//#include "Debug.h"
+#include <stdio.h>
+#include <stdlib.h>
+
+DWORD get_fattime (void) {
+ return 999;
+}
+
+namespace mbed {
+
+#if FFSDEBUG_ENABLED
+static const char *FR_ERRORS[] = {
+ "FR_OK = 0",
+ "FR_NOT_READY",
+ "FR_NO_FILE",
+ "FR_NO_PATH",
+ "FR_INVALID_NAME",
+ "FR_INVALID_DRIVE",
+ "FR_DENIED",
+ "FR_EXIST",
+ "FR_RW_ERROR",
+ "FR_WRITE_PROTECTED",
+ "FR_NOT_ENABLED",
+ "FR_NO_FILESYSTEM",
+ "FR_INVALID_OBJECT",
+ "FR_MKFS_ABORTED"
+};
+#endif
+
+FATFileSystem *FATFileSystem::_ffs[_VOLUMES] = {0};
+
+FATFileSystem::FATFileSystem(const char* n) : FileSystemLike(n) {
+ FFSDEBUG("FATFileSystem(%s)\n", n);
+ for(int i=0; i<_VOLUMES; i++) {
+ if(_ffs[i] == 0) {
+ _ffs[i] = this;
+ _fsid = i;
+ FFSDEBUG("Mounting [%s] on ffs drive [%d]\n", _name, _fsid);
+ f_mount(i, &_fs);
+ return;
+ }
+ }
+ error("Couldn't create %s in FATFileSystem::FATFileSystem\n",n);
+}
+
+FATFileSystem::~FATFileSystem() {
+ for(int i=0; i<_VOLUMES; i++) {
+ if(_ffs[i] == this) {
+ _ffs[i] = 0;
+ f_mount(i, NULL);
+ }
+ }
+}
+
+FileHandle *FATFileSystem::open(const char* name, int flags) {
+ FFSDEBUG("open(%s) on filesystem [%s], drv [%d]\n", name, _name, _fsid);
+ char n[64];
+ sprintf(n, "%d:/%s", _fsid, name);
+
+ /* POSIX flags -> FatFS open mode */
+ BYTE openmode;
+ if(flags & O_RDWR) {
+ openmode = FA_READ|FA_WRITE;
+ } else if(flags & O_WRONLY) {
+ openmode = FA_WRITE;
+ } else {
+ openmode = FA_READ;
+ }
+ if(flags & O_CREAT) {
+ if(flags & O_TRUNC) {
+ openmode |= FA_CREATE_ALWAYS;
+ } else {
+ openmode |= FA_OPEN_ALWAYS;
+ }
+ }
+
+ FIL fh;
+ FRESULT res = f_open(&fh, n, openmode);
+ if(res) {
+ FFSDEBUG("f_open('w') failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return NULL;
+ }
+ if(flags & O_APPEND) {
+ f_lseek(&fh, fh.fsize);
+ }
+ return new FATFileHandle(fh);
+}
+
+int FATFileSystem::remove(const char *filename) {
+ FRESULT res = f_unlink(filename);
+ if(res) {
+ FFSDEBUG("f_unlink() failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return -1;
+ }
+ return 0;
+}
+
+int FATFileSystem::format() {
+ FFSDEBUG("format()\n");
+ FRESULT res = f_mkfs(_fsid, 0, 512); // Logical drive number, Partitioning rule, Allocation unit size (bytes per cluster)
+ if(res) {
+ FFSDEBUG("f_mkfs() failed (%d, %s)\n", res, FR_ERRORS[res]);
+ return -1;
+ }
+ return 0;
+}
+
+DirHandle *FATFileSystem::opendir(const char *name) {
+ FATFS_DIR dir;
+ FRESULT res = f_opendir(&dir, name);
+ if(res != 0) {
+ return NULL;
+ }
+ return new FATDirHandle(dir);
+}
+
+int FATFileSystem::mkdir(const char *name, mode_t mode) {
+ FRESULT res = f_mkdir(name);
+ return res == 0 ? 0 : -1;
+}
+
+} // namespace mbed
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/FATFileSystem.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,61 @@
+/* mbed Microcontroller Library - FATFileSystem
+ * Copyright (c) 2008, sford
+ */
+
+/* Library: FATFileSystem.h
+ * A library of stuff to make a fat filesystem on top of a block device
+ */
+
+#ifndef MBED_FATFILESYSTEM_H
+#define MBED_FATFILESYSTEM_H
+
+#ifndef FFSDEBUG_ENABLED
+#define FFSDEBUG_ENABLED 0
+#endif
+
+#if FFSDEBUG_ENABLED
+#define FFSDEBUG(FMT, ...) printf(FMT, ##__VA_ARGS__)
+#else
+#define FFSDEBUG(FMT, ...)
+#endif
+
+#include "FileSystemLike.h"
+#include "FileHandle.h"
+#include "ff.h"
+#include "diskio.h"
+
+namespace mbed {
+/* Class: FATFileSystem
+ * The class itself
+ */
+class FATFileSystem : public FileSystemLike {
+public:
+
+ FATFileSystem(const char* n);
+ virtual ~FATFileSystem();
+
+ /* Function: open
+ * open a file on the filesystem. never called directly
+ */
+ virtual FileHandle *open(const char* name, int flags);
+ virtual int remove(const char *filename);
+ virtual int format();
+ virtual DirHandle *opendir(const char *name);
+ virtual int mkdir(const char *name, mode_t mode);
+
+ FATFS _fs; // Work area (file system object) for logical drive
+ static FATFileSystem *_ffs[_VOLUMES]; // FATFileSystem objects, as parallel to FatFs drives array
+ int _fsid;
+
+ virtual int disk_initialize() { return 0; }
+ virtual int disk_status() { return 0; }
+ virtual int disk_read(char *buffer, int sector) = 0;
+ virtual int disk_write(const char *buffer, int sector) = 0;
+ virtual int disk_sync() { return 0; }
+ virtual int disk_sectors() = 0;
+
+};
+
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/MemFileSystem.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,75 @@
+/* mbed Microcontroller Library - MemFileSystem
+ * Copyright (c) 2008, sford
+ */
+
+
+#ifndef MBED_MEMFILESYSTEM_H
+#define MBED_MEMFILESYSTEM_H
+
+#include "FATFileSystem.h"
+
+namespace mbed {
+
+class MemFileSystem : public FATFileSystem {
+public:
+
+ // 2000 sectors, each 512 bytes (malloced as required)
+ char *sectors[2000];
+
+ MemFileSystem(const char* name) : FATFileSystem(name) {
+ memset(sectors, 0, sizeof(sectors));
+ }
+
+ virtual ~MemFileSystem() {
+ for(int i = 0; i < 2000; i++) {
+ if(sectors[i]) {
+ free(sectors[i]);
+ }
+ }
+ }
+
+ // read a sector in to the buffer, return 0 if ok
+ virtual int disk_read(char *buffer, int sector) {
+ if(sectors[sector] == 0) {
+ // nothing allocated means sector is empty
+ memset(buffer, 0, 512);
+ } else {
+ memcpy(buffer, sectors[sector], 512);
+ }
+ return 0;
+ }
+
+ // write a sector from the buffer, return 0 if ok
+ virtual int disk_write(const char *buffer, int sector) {
+ // if buffer is zero deallocate sector
+ char zero[512];
+ memset(zero, 0, 512);
+ if(memcmp(zero, buffer, 512)==0) {
+ if(sectors[sector] != 0) {
+ free(sectors[sector]);
+ sectors[sector] = 0;
+ }
+ return 0;
+ }
+ // else allocate a sector if needed, and write
+ if(sectors[sector] == 0) {
+ char *sec = (char*)malloc(512);
+ if(sec==0) {
+ return 1; // out of memory
+ }
+ sectors[sector] = sec;
+ }
+ memcpy(sectors[sector], buffer, 512);
+ return 0;
+ }
+
+ // return the number of sectors
+ virtual int disk_sectors() {
+ return sizeof(sectors)/sizeof(sectors[0]);
+ }
+
+};
+
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/diskio.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,105 @@
+/*-----------------------------------------------------------------------*/
+/* Low level disk I/O module skeleton for FatFs (C)ChaN, 2007 */
+/*-----------------------------------------------------------------------*/
+/* This is a stub disk I/O module that acts as front end of the existing */
+/* disk I/O modules and attach it to FatFs module with common interface. */
+/*-----------------------------------------------------------------------*/
+
+#include "diskio.h"
+#include <stdio.h>
+#include <string.h>
+#include "FATFileSystem.h"
+
+#include "mbed.h"
+
+DSTATUS disk_initialize (
+ BYTE drv /* Physical drive nmuber (0..) */
+)
+{
+ FFSDEBUG("disk_initialize on drv [%d]\n", drv);
+ return (DSTATUS)FATFileSystem::_ffs[drv]->disk_initialize();
+}
+
+DSTATUS disk_status (
+ BYTE drv /* Physical drive nmuber (0..) */
+)
+{
+ FFSDEBUG("disk_status on drv [%d]\n", drv);
+ return (DSTATUS)FATFileSystem::_ffs[drv]->disk_status();
+}
+
+DRESULT disk_read (
+ BYTE drv, /* Physical drive nmuber (0..) */
+ BYTE *buff, /* Data buffer to store read data */
+ DWORD sector, /* Sector address (LBA) */
+ BYTE count /* Number of sectors to read (1..255) */
+)
+{
+ FFSDEBUG("disk_read(sector %d, count %d) on drv [%d]\n", sector, count, drv);
+ for(DWORD s=sector; s<sector+count; s++) {
+ FFSDEBUG(" disk_read(sector %d)\n", s);
+ int res = FATFileSystem::_ffs[drv]->disk_read((char*)buff, s);
+ if(res) {
+ return RES_PARERR;
+ }
+ buff += 512;
+ }
+ return RES_OK;
+}
+
+#if _READONLY == 0
+DRESULT disk_write (
+ BYTE drv, /* Physical drive nmuber (0..) */
+ const BYTE *buff, /* Data to be written */
+ DWORD sector, /* Sector address (LBA) */
+ BYTE count /* Number of sectors to write (1..255) */
+)
+{
+ FFSDEBUG("disk_write(sector %d, count %d) on drv [%d]\n", sector, count, drv);
+ for(DWORD s=sector; s<sector+count; s++) {
+ FFSDEBUG(" disk_write(sector %d)\n", s);
+ int res = FATFileSystem::_ffs[drv]->disk_write((char*)buff, s);
+ if(res) {
+ return RES_PARERR;
+ }
+ buff += 512;
+ }
+ return RES_OK;
+}
+#endif /* _READONLY */
+
+DRESULT disk_ioctl (
+ BYTE drv, /* Physical drive nmuber (0..) */
+ BYTE ctrl, /* Control code */
+ void *buff /* Buffer to send/receive control data */
+)
+{
+ FFSDEBUG("disk_ioctl(%d)\n", ctrl);
+ switch(ctrl) {
+ case CTRL_SYNC:
+ if(FATFileSystem::_ffs[drv] == NULL) {
+ return RES_NOTRDY;
+ } else if(FATFileSystem::_ffs[drv]->disk_sync()) {
+ return RES_ERROR;
+ }
+ return RES_OK;
+ case GET_SECTOR_COUNT:
+ if(FATFileSystem::_ffs[drv] == NULL) {
+ return RES_NOTRDY;
+ } else {
+ int res = FATFileSystem::_ffs[drv]->disk_sectors();
+ if(res > 0) {
+ *((DWORD*)buff) = res; // minimum allowed
+ return RES_OK;
+ } else {
+ return RES_ERROR;
+ }
+ }
+ case GET_BLOCK_SIZE:
+ *((DWORD*)buff) = 1; // default when not known
+ return RES_OK;
+
+ }
+ return RES_PARERR;
+}
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/diskio.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,78 @@
+/*-----------------------------------------------------------------------
+/ Low level disk interface modlue include file
+/-----------------------------------------------------------------------*/
+
+#ifndef _DISKIO
+
+#define _READONLY 0 /* 1: Remove write functions */
+#define _USE_IOCTL 1 /* 1: Use disk_ioctl fucntion */
+
+#include "integer.h"
+
+
+/* Status of Disk Functions */
+typedef BYTE DSTATUS;
+
+/* Results of Disk Functions */
+typedef enum {
+ RES_OK = 0, /* 0: Successful */
+ RES_ERROR, /* 1: R/W Error */
+ RES_WRPRT, /* 2: Write Protected */
+ RES_NOTRDY, /* 3: Not Ready */
+ RES_PARERR /* 4: Invalid Parameter */
+} DRESULT;
+
+
+/*---------------------------------------*/
+/* Prototypes for disk control functions */
+
+int assign_drives (int, int);
+DSTATUS disk_initialize (BYTE);
+DSTATUS disk_status (BYTE);
+DRESULT disk_read (BYTE, BYTE*, DWORD, BYTE);
+#if _READONLY == 0
+DRESULT disk_write (BYTE, const BYTE*, DWORD, BYTE);
+#endif
+DRESULT disk_ioctl (BYTE, BYTE, void*);
+
+
+
+/* Disk Status Bits (DSTATUS) */
+
+#define STA_NOINIT 0x01 /* Drive not initialized */
+#define STA_NODISK 0x02 /* No medium in the drive */
+#define STA_PROTECT 0x04 /* Write protected */
+
+
+/* Command code for disk_ioctrl fucntion */
+
+/* Generic command (defined for FatFs) */
+#define CTRL_SYNC 0 /* Flush disk cache (for write functions) */
+#define GET_SECTOR_COUNT 1 /* Get media size (for only f_mkfs()) */
+#define GET_SECTOR_SIZE 2 /* Get sector size (for multiple sector size (_MAX_SS >= 1024)) */
+#define GET_BLOCK_SIZE 3 /* Get erase block size (for only f_mkfs()) */
+#define CTRL_ERASE_SECTOR 4 /* Force erased a block of sectors (for only _USE_ERASE) */
+
+/* Generic command */
+#define CTRL_POWER 5 /* Get/Set power status */
+#define CTRL_LOCK 6 /* Lock/Unlock media removal */
+#define CTRL_EJECT 7 /* Eject media */
+
+/* MMC/SDC specific ioctl command */
+#define MMC_GET_TYPE 10 /* Get card type */
+#define MMC_GET_CSD 11 /* Get CSD */
+#define MMC_GET_CID 12 /* Get CID */
+#define MMC_GET_OCR 13 /* Get OCR */
+#define MMC_GET_SDSTAT 14 /* Get SD status */
+
+/* ATA/CF specific ioctl command */
+#define ATA_GET_REV 20 /* Get F/W revision */
+#define ATA_GET_MODEL 21 /* Get model name */
+#define ATA_GET_SN 22 /* Get serial number */
+
+/* NAND specific ioctl command */
+#define NAND_FORMAT 30 /* Create physical format */
+
+
+#define _DISKIO
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/ff.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,4077 @@
+/*----------------------------------------------------------------------------/
+/ FatFs - FAT file system module R0.09 (C)ChaN, 2011
+/-----------------------------------------------------------------------------/
+/ FatFs module is a generic FAT file system module for small embedded systems.
+/ This is a free software that opened for education, research and commercial
+/ developments under license policy of following terms.
+/
+/ Copyright (C) 2011, ChaN, all right reserved.
+/
+/ * The FatFs module is a free software and there is NO WARRANTY.
+/ * No restriction on use. You can use, modify and redistribute it for
+/ personal, non-profit or commercial products UNDER YOUR RESPONSIBILITY.
+/ * Redistributions of source code must retain the above copyright notice.
+/
+/-----------------------------------------------------------------------------/
+/ Feb 26,'06 R0.00 Prototype.
+/
+/ Apr 29,'06 R0.01 First stable version.
+/
+/ Jun 01,'06 R0.02 Added FAT12 support.
+/ Removed unbuffered mode.
+/ Fixed a problem on small (<32M) partition.
+/ Jun 10,'06 R0.02a Added a configuration option (_FS_MINIMUM).
+/
+/ Sep 22,'06 R0.03 Added f_rename().
+/ Changed option _FS_MINIMUM to _FS_MINIMIZE.
+/ Dec 11,'06 R0.03a Improved cluster scan algorithm to write files fast.
+/ Fixed f_mkdir() creates incorrect directory on FAT32.
+/
+/ Feb 04,'07 R0.04 Supported multiple drive system.
+/ Changed some interfaces for multiple drive system.
+/ Changed f_mountdrv() to f_mount().
+/ Added f_mkfs().
+/ Apr 01,'07 R0.04a Supported multiple partitions on a physical drive.
+/ Added a capability of extending file size to f_lseek().
+/ Added minimization level 3.
+/ Fixed an endian sensitive code in f_mkfs().
+/ May 05,'07 R0.04b Added a configuration option _USE_NTFLAG.
+/ Added FSInfo support.
+/ Fixed DBCS name can result FR_INVALID_NAME.
+/ Fixed short seek (<= csize) collapses the file object.
+/
+/ Aug 25,'07 R0.05 Changed arguments of f_read(), f_write() and f_mkfs().
+/ Fixed f_mkfs() on FAT32 creates incorrect FSInfo.
+/ Fixed f_mkdir() on FAT32 creates incorrect directory.
+/ Feb 03,'08 R0.05a Added f_truncate() and f_utime().
+/ Fixed off by one error at FAT sub-type determination.
+/ Fixed btr in f_read() can be mistruncated.
+/ Fixed cached sector is not flushed when create and close without write.
+/
+/ Apr 01,'08 R0.06 Added fputc(), fputs(), fprintf() and fgets().
+/ Improved performance of f_lseek() on moving to the same or following cluster.
+/
+/ Apr 01,'09 R0.07 Merged Tiny-FatFs as a configuration option. (_FS_TINY)
+/ Added long file name feature.
+/ Added multiple code page feature.
+/ Added re-entrancy for multitask operation.
+/ Added auto cluster size selection to f_mkfs().
+/ Added rewind option to f_readdir().
+/ Changed result code of critical errors.
+/ Renamed string functions to avoid name collision.
+/ Apr 14,'09 R0.07a Separated out OS dependent code on reentrant cfg.
+/ Added multiple sector size feature.
+/ Jun 21,'09 R0.07c Fixed f_unlink() can return FR_OK on error.
+/ Fixed wrong cache control in f_lseek().
+/ Added relative path feature.
+/ Added f_chdir() and f_chdrive().
+/ Added proper case conversion to extended char.
+/ Nov 03,'09 R0.07e Separated out configuration options from ff.h to ffconf.h.
+/ Fixed f_unlink() fails to remove a sub-dir on _FS_RPATH.
+/ Fixed name matching error on the 13 char boundary.
+/ Added a configuration option, _LFN_UNICODE.
+/ Changed f_readdir() to return the SFN with always upper case on non-LFN cfg.
+/
+/ May 15,'10 R0.08 Added a memory configuration option. (_USE_LFN = 3)
+/ Added file lock feature. (_FS_SHARE)
+/ Added fast seek feature. (_USE_FASTSEEK)
+/ Changed some types on the API, XCHAR->TCHAR.
+/ Changed fname member in the FILINFO structure on Unicode cfg.
+/ String functions support UTF-8 encoding files on Unicode cfg.
+/ Aug 16,'10 R0.08a Added f_getcwd(). (_FS_RPATH = 2)
+/ Added sector erase feature. (_USE_ERASE)
+/ Moved file lock semaphore table from fs object to the bss.
+/ Fixed a wrong directory entry is created on non-LFN cfg when the given name contains ';'.
+/ Fixed f_mkfs() creates wrong FAT32 volume.
+/ Jan 15,'11 R0.08b Fast seek feature is also applied to f_read() and f_write().
+/ f_lseek() reports required table size on creating CLMP.
+/ Extended format syntax of f_printf function.
+/ Ignores duplicated directory separators in given path names.
+/
+/ Sep 06,'11 R0.09 f_mkfs() supports multiple partition to finish the multiple partition feature.
+/ Added f_fdisk(). (_MULTI_PARTITION = 2)
+/---------------------------------------------------------------------------*/
+
+#include "ff.h" /* FatFs configurations and declarations */
+#include "diskio.h" /* Declarations of low level disk I/O functions */
+
+
+/*--------------------------------------------------------------------------
+
+ Module Private Definitions
+
+---------------------------------------------------------------------------*/
+
+#if _FATFS != 6502 /* Revision ID */
+#error Wrong include file (ff.h).
+#endif
+
+
+/* Definitions on sector size */
+#if _MAX_SS != 512 && _MAX_SS != 1024 && _MAX_SS != 2048 && _MAX_SS != 4096
+#error Wrong sector size.
+#endif
+#if _MAX_SS != 512
+#define SS(fs) ((fs)->ssize) /* Variable sector size */
+#else
+#define SS(fs) 512U /* Fixed sector size */
+#endif
+
+
+/* Reentrancy related */
+#if _FS_REENTRANT
+#if _USE_LFN == 1
+#error Static LFN work area must not be used in re-entrant configuration.
+#endif
+#define ENTER_FF(fs) { if (!lock_fs(fs)) return FR_TIMEOUT; }
+#define LEAVE_FF(fs, res) { unlock_fs(fs, res); return res; }
+#else
+#define ENTER_FF(fs)
+#define LEAVE_FF(fs, res) return res
+#endif
+
+#define ABORT(fs, res) { fp->flag |= FA__ERROR; LEAVE_FF(fs, res); }
+
+
+/* File shareing feature */
+#if _FS_SHARE
+#if _FS_READONLY
+#error _FS_SHARE must be 0 on read-only cfg.
+#endif
+typedef struct {
+ FATFS *fs; /* File ID 1, volume (NULL:blank entry) */
+ DWORD clu; /* File ID 2, directory */
+ WORD idx; /* File ID 3, directory index */
+ WORD ctr; /* File open counter, 0:none, 0x01..0xFF:read open count, 0x100:write mode */
+} FILESEM;
+#endif
+
+
+/* Misc definitions */
+#define LD_CLUST(dir) (((DWORD)LD_WORD(dir+DIR_FstClusHI)<<16) | LD_WORD(dir+DIR_FstClusLO))
+#define ST_CLUST(dir,cl) {ST_WORD(dir+DIR_FstClusLO, cl); ST_WORD(dir+DIR_FstClusHI, (DWORD)cl>>16);}
+
+
+/* DBCS code ranges and SBCS extend char conversion table */
+
+#if _CODE_PAGE == 932 /* Japanese Shift-JIS */
+#define _DF1S 0x81 /* DBC 1st byte range 1 start */
+#define _DF1E 0x9F /* DBC 1st byte range 1 end */
+#define _DF2S 0xE0 /* DBC 1st byte range 2 start */
+#define _DF2E 0xFC /* DBC 1st byte range 2 end */
+#define _DS1S 0x40 /* DBC 2nd byte range 1 start */
+#define _DS1E 0x7E /* DBC 2nd byte range 1 end */
+#define _DS2S 0x80 /* DBC 2nd byte range 2 start */
+#define _DS2E 0xFC /* DBC 2nd byte range 2 end */
+
+#elif _CODE_PAGE == 936 /* Simplified Chinese GBK */
+#define _DF1S 0x81
+#define _DF1E 0xFE
+#define _DS1S 0x40
+#define _DS1E 0x7E
+#define _DS2S 0x80
+#define _DS2E 0xFE
+
+#elif _CODE_PAGE == 949 /* Korean */
+#define _DF1S 0x81
+#define _DF1E 0xFE
+#define _DS1S 0x41
+#define _DS1E 0x5A
+#define _DS2S 0x61
+#define _DS2E 0x7A
+#define _DS3S 0x81
+#define _DS3E 0xFE
+
+#elif _CODE_PAGE == 950 /* Traditional Chinese Big5 */
+#define _DF1S 0x81
+#define _DF1E 0xFE
+#define _DS1S 0x40
+#define _DS1E 0x7E
+#define _DS2S 0xA1
+#define _DS2E 0xFE
+
+#elif _CODE_PAGE == 437 /* U.S. (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x90,0x41,0x8E,0x41,0x8F,0x80,0x45,0x45,0x45,0x49,0x49,0x49,0x8E,0x8F,0x90,0x92,0x92,0x4F,0x99,0x4F,0x55,0x55,0x59,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0x41,0x49,0x4F,0x55,0xA5,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0x21,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE4,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 720 /* Arabic (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x45,0x41,0x84,0x41,0x86,0x43,0x45,0x45,0x45,0x49,0x49,0x8D,0x8E,0x8F,0x90,0x92,0x92,0x93,0x94,0x95,0x49,0x49,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE4,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 737 /* Greek (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x92,0x92,0x93,0x94,0x95,0x96,0x97,0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87, \
+ 0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0xAA,0x92,0x93,0x94,0x95,0x96,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0x97,0xEA,0xEB,0xEC,0xE4,0xED,0xEE,0xE7,0xE8,0xF1,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 775 /* Baltic (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x91,0xA0,0x8E,0x95,0x8F,0x80,0xAD,0xED,0x8A,0x8A,0xA1,0x8D,0x8E,0x8F,0x90,0x92,0x92,0xE2,0x99,0x95,0x96,0x97,0x97,0x99,0x9A,0x9D,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xE0,0xA3,0xA3,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xB5,0xB6,0xB7,0xB8,0xBD,0xBE,0xC6,0xC7,0xA5,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE5,0xE5,0xE6,0xE3,0xE8,0xE8,0xEA,0xEA,0xEE,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 850 /* Multilingual Latin 1 (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x90,0xB6,0x8E,0xB7,0x8F,0x80,0xD2,0xD3,0xD4,0xD8,0xD7,0xDE,0x8E,0x8F,0x90,0x92,0x92,0xE2,0x99,0xE3,0xEA,0xEB,0x59,0x99,0x9A,0x9D,0x9C,0x9D,0x9E,0x9F, \
+ 0xB5,0xD6,0xE0,0xE9,0xA5,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0x21,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC7,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE5,0xE5,0xE6,0xE7,0xE7,0xE9,0xEA,0xEB,0xED,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 852 /* Latin 2 (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x90,0xB6,0x8E,0xDE,0x8F,0x80,0x9D,0xD3,0x8A,0x8A,0xD7,0x8D,0x8E,0x8F,0x90,0x91,0x91,0xE2,0x99,0x95,0x95,0x97,0x97,0x99,0x9A,0x9B,0x9B,0x9D,0x9E,0x9F, \
+ 0xB5,0xD6,0xE0,0xE9,0xA4,0xA4,0xA6,0xA6,0xA8,0xA8,0xAA,0x8D,0xAC,0xB8,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBD,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC6,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD1,0xD1,0xD2,0xD3,0xD2,0xD5,0xD6,0xD7,0xB7,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE3,0xD5,0xE6,0xE6,0xE8,0xE9,0xE8,0xEB,0xED,0xED,0xDD,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xEB,0xFC,0xFC,0xFE,0xFF}
+
+#elif _CODE_PAGE == 855 /* Cyrillic (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x81,0x81,0x83,0x83,0x85,0x85,0x87,0x87,0x89,0x89,0x8B,0x8B,0x8D,0x8D,0x8F,0x8F,0x91,0x91,0x93,0x93,0x95,0x95,0x97,0x97,0x99,0x99,0x9B,0x9B,0x9D,0x9D,0x9F,0x9F, \
+ 0xA1,0xA1,0xA3,0xA3,0xA5,0xA5,0xA7,0xA7,0xA9,0xA9,0xAB,0xAB,0xAD,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB6,0xB6,0xB8,0xB8,0xB9,0xBA,0xBB,0xBC,0xBE,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC7,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD1,0xD1,0xD3,0xD3,0xD5,0xD5,0xD7,0xD7,0xDD,0xD9,0xDA,0xDB,0xDC,0xDD,0xE0,0xDF, \
+ 0xE0,0xE2,0xE2,0xE4,0xE4,0xE6,0xE6,0xE8,0xE8,0xEA,0xEA,0xEC,0xEC,0xEE,0xEE,0xEF,0xF0,0xF2,0xF2,0xF4,0xF4,0xF6,0xF6,0xF8,0xF8,0xFA,0xFA,0xFC,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 857 /* Turkish (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x90,0xB6,0x8E,0xB7,0x8F,0x80,0xD2,0xD3,0xD4,0xD8,0xD7,0x98,0x8E,0x8F,0x90,0x92,0x92,0xE2,0x99,0xE3,0xEA,0xEB,0x98,0x99,0x9A,0x9D,0x9C,0x9D,0x9E,0x9E, \
+ 0xB5,0xD6,0xE0,0xE9,0xA5,0xA5,0xA6,0xA6,0xA8,0xA9,0xAA,0xAB,0xAC,0x21,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC7,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE5,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xDE,0x59,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 858 /* Multilingual Latin 1 + Euro (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x9A,0x90,0xB6,0x8E,0xB7,0x8F,0x80,0xD2,0xD3,0xD4,0xD8,0xD7,0xDE,0x8E,0x8F,0x90,0x92,0x92,0xE2,0x99,0xE3,0xEA,0xEB,0x59,0x99,0x9A,0x9D,0x9C,0x9D,0x9E,0x9F, \
+ 0xB5,0xD6,0xE0,0xE9,0xA5,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0x21,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC7,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD1,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE5,0xE5,0xE6,0xE7,0xE7,0xE9,0xEA,0xEB,0xED,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 862 /* Hebrew (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0x41,0x49,0x4F,0x55,0xA5,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0x21,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE4,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 866 /* Russian (OEM) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0x90,0x91,0x92,0x93,0x9d,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F,0xF0,0xF0,0xF2,0xF2,0xF4,0xF4,0xF6,0xF6,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 874 /* Thai (OEM, Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE4,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 1250 /* Central Europe (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x8A,0x9B,0x8C,0x8D,0x8E,0x8F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xA3,0xB4,0xB5,0xB6,0xB7,0xB8,0xA5,0xAA,0xBB,0xBC,0xBD,0xBC,0xAF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xF7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xFF}
+
+#elif _CODE_PAGE == 1251 /* Cyrillic (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x82,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x80,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x8A,0x9B,0x8C,0x8D,0x8E,0x8F, \
+ 0xA0,0xA2,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB2,0xA5,0xB5,0xB6,0xB7,0xA8,0xB9,0xAA,0xBB,0xA3,0xBD,0xBD,0xAF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF}
+
+#elif _CODE_PAGE == 1252 /* Latin 1 (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0xAd,0x9B,0x8C,0x9D,0xAE,0x9F, \
+ 0xA0,0x21,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xF7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0x9F}
+
+#elif _CODE_PAGE == 1253 /* Greek (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xA2,0xB8,0xB9,0xBA, \
+ 0xE0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xF2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xFB,0xBC,0xFD,0xBF,0xFF}
+
+#elif _CODE_PAGE == 1254 /* Turkish (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x8A,0x9B,0x8C,0x9D,0x9E,0x9F, \
+ 0xA0,0x21,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xF7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0x9F}
+
+#elif _CODE_PAGE == 1255 /* Hebrew (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0x21,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xE0,0xE1,0xE2,0xE3,0xE4,0xE5,0xE6,0xE7,0xE8,0xE9,0xEA,0xEB,0xEC,0xED,0xEE,0xEF,0xF0,0xF1,0xF2,0xF3,0xF4,0xF5,0xF6,0xF7,0xF8,0xF9,0xFA,0xFB,0xFC,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 1256 /* Arabic (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x8C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0x41,0xE1,0x41,0xE3,0xE4,0xE5,0xE6,0x43,0x45,0x45,0x45,0x45,0xEC,0xED,0x49,0x49,0xF0,0xF1,0xF2,0xF3,0x4F,0xF5,0xF6,0xF7,0xF8,0x55,0xFA,0x55,0x55,0xFD,0xFE,0xFF}
+
+#elif _CODE_PAGE == 1257 /* Baltic (Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0x9C,0x9D,0x9E,0x9F, \
+ 0xA0,0xA1,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xA8,0xB9,0xAA,0xBB,0xBC,0xBD,0xBE,0xAF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xF7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xFF}
+
+#elif _CODE_PAGE == 1258 /* Vietnam (OEM, Windows) */
+#define _DF1S 0
+#define _EXCVT {0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8A,0x8B,0x8C,0x8D,0x8E,0x8F,0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98,0x99,0x9A,0x9B,0xAC,0x9D,0x9E,0x9F, \
+ 0xA0,0x21,0xA2,0xA3,0xA4,0xA5,0xA6,0xA7,0xA8,0xA9,0xAA,0xAB,0xAC,0xAD,0xAE,0xAF,0xB0,0xB1,0xB2,0xB3,0xB4,0xB5,0xB6,0xB7,0xB8,0xB9,0xBA,0xBB,0xBC,0xBD,0xBE,0xBF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xCC,0xCD,0xCE,0xCF,0xD0,0xD1,0xD2,0xD3,0xD4,0xD5,0xD6,0xD7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xDE,0xDF, \
+ 0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB,0xEC,0xCD,0xCE,0xCF,0xD0,0xD1,0xF2,0xD3,0xD4,0xD5,0xD6,0xF7,0xD8,0xD9,0xDA,0xDB,0xDC,0xDD,0xFE,0x9F}
+
+#elif _CODE_PAGE == 1 /* ASCII (for only non-LFN cfg) */
+#if _USE_LFN
+#error Cannot use LFN feature without valid code page.
+#endif
+#define _DF1S 0
+
+#else
+#error Unknown code page
+
+#endif
+
+
+/* Character code support macros */
+#define IsUpper(c) (((c)>='A')&&((c)<='Z'))
+#define IsLower(c) (((c)>='a')&&((c)<='z'))
+#define IsDigit(c) (((c)>='0')&&((c)<='9'))
+
+#if _DF1S /* Code page is DBCS */
+
+#ifdef _DF2S /* Two 1st byte areas */
+#define IsDBCS1(c) (((BYTE)(c) >= _DF1S && (BYTE)(c) <= _DF1E) || ((BYTE)(c) >= _DF2S && (BYTE)(c) <= _DF2E))
+#else /* One 1st byte area */
+#define IsDBCS1(c) ((BYTE)(c) >= _DF1S && (BYTE)(c) <= _DF1E)
+#endif
+
+#ifdef _DS3S /* Three 2nd byte areas */
+#define IsDBCS2(c) (((BYTE)(c) >= _DS1S && (BYTE)(c) <= _DS1E) || ((BYTE)(c) >= _DS2S && (BYTE)(c) <= _DS2E) || ((BYTE)(c) >= _DS3S && (BYTE)(c) <= _DS3E))
+#else /* Two 2nd byte areas */
+#define IsDBCS2(c) (((BYTE)(c) >= _DS1S && (BYTE)(c) <= _DS1E) || ((BYTE)(c) >= _DS2S && (BYTE)(c) <= _DS2E))
+#endif
+
+#else /* Code page is SBCS */
+
+#define IsDBCS1(c) 0
+#define IsDBCS2(c) 0
+
+#endif /* _DF1S */
+
+
+/* Name status flags */
+#define NS 11 /* Index of name status byte in fn[] */
+#define NS_LOSS 0x01 /* Out of 8.3 format */
+#define NS_LFN 0x02 /* Force to create LFN entry */
+#define NS_LAST 0x04 /* Last segment */
+#define NS_BODY 0x08 /* Lower case flag (body) */
+#define NS_EXT 0x10 /* Lower case flag (ext) */
+#define NS_DOT 0x20 /* Dot entry */
+
+
+/* FAT sub-type boundaries */
+/* Note that the FAT spec by Microsoft says 4085 but Windows works with 4087! */
+#define MIN_FAT16 4086 /* Minimum number of clusters for FAT16 */
+#define MIN_FAT32 65526 /* Minimum number of clusters for FAT32 */
+
+
+/* FatFs refers the members in the FAT structures as byte array instead of
+/ structure member because the structure is not binary compatible between
+/ different platforms */
+
+#define BS_jmpBoot 0 /* Jump instruction (3) */
+#define BS_OEMName 3 /* OEM name (8) */
+#define BPB_BytsPerSec 11 /* Sector size [byte] (2) */
+#define BPB_SecPerClus 13 /* Cluster size [sector] (1) */
+#define BPB_RsvdSecCnt 14 /* Size of reserved area [sector] (2) */
+#define BPB_NumFATs 16 /* Number of FAT copies (1) */
+#define BPB_RootEntCnt 17 /* Number of root dir entries for FAT12/16 (2) */
+#define BPB_TotSec16 19 /* Volume size [sector] (2) */
+#define BPB_Media 21 /* Media descriptor (1) */
+#define BPB_FATSz16 22 /* FAT size [sector] (2) */
+#define BPB_SecPerTrk 24 /* Track size [sector] (2) */
+#define BPB_NumHeads 26 /* Number of heads (2) */
+#define BPB_HiddSec 28 /* Number of special hidden sectors (4) */
+#define BPB_TotSec32 32 /* Volume size [sector] (4) */
+#define BS_DrvNum 36 /* Physical drive number (2) */
+#define BS_BootSig 38 /* Extended boot signature (1) */
+#define BS_VolID 39 /* Volume serial number (4) */
+#define BS_VolLab 43 /* Volume label (8) */
+#define BS_FilSysType 54 /* File system type (1) */
+#define BPB_FATSz32 36 /* FAT size [sector] (4) */
+#define BPB_ExtFlags 40 /* Extended flags (2) */
+#define BPB_FSVer 42 /* File system version (2) */
+#define BPB_RootClus 44 /* Root dir first cluster (4) */
+#define BPB_FSInfo 48 /* Offset of FSInfo sector (2) */
+#define BPB_BkBootSec 50 /* Offset of backup boot sectot (2) */
+#define BS_DrvNum32 64 /* Physical drive number (2) */
+#define BS_BootSig32 66 /* Extended boot signature (1) */
+#define BS_VolID32 67 /* Volume serial number (4) */
+#define BS_VolLab32 71 /* Volume label (8) */
+#define BS_FilSysType32 82 /* File system type (1) */
+#define FSI_LeadSig 0 /* FSI: Leading signature (4) */
+#define FSI_StrucSig 484 /* FSI: Structure signature (4) */
+#define FSI_Free_Count 488 /* FSI: Number of free clusters (4) */
+#define FSI_Nxt_Free 492 /* FSI: Last allocated cluster (4) */
+#define MBR_Table 446 /* MBR: Partition table offset (2) */
+#define SZ_PTE 16 /* MBR: Size of a partition table entry */
+#define BS_55AA 510 /* Boot sector signature (2) */
+
+#define DIR_Name 0 /* Short file name (11) */
+#define DIR_Attr 11 /* Attribute (1) */
+#define DIR_NTres 12 /* NT flag (1) */
+#define DIR_CrtTime 14 /* Created time (2) */
+#define DIR_CrtDate 16 /* Created date (2) */
+#define DIR_FstClusHI 20 /* Higher 16-bit of first cluster (2) */
+#define DIR_WrtTime 22 /* Modified time (2) */
+#define DIR_WrtDate 24 /* Modified date (2) */
+#define DIR_FstClusLO 26 /* Lower 16-bit of first cluster (2) */
+#define DIR_FileSize 28 /* File size (4) */
+#define LDIR_Ord 0 /* LFN entry order and LLE flag (1) */
+#define LDIR_Attr 11 /* LFN attribute (1) */
+#define LDIR_Type 12 /* LFN type (1) */
+#define LDIR_Chksum 13 /* Sum of corresponding SFN entry */
+#define LDIR_FstClusLO 26 /* Filled by zero (0) */
+#define SZ_DIR 32 /* Size of a directory entry */
+#define LLE 0x40 /* Last long entry flag in LDIR_Ord */
+#define DDE 0xE5 /* Deleted directory enrty mark in DIR_Name[0] */
+#define NDDE 0x05 /* Replacement of a character collides with DDE */
+
+
+/*------------------------------------------------------------*/
+/* Module private work area */
+/*------------------------------------------------------------*/
+/* Note that uninitialized variables with static duration are
+/ zeroed/nulled at start-up. If not, the compiler or start-up
+/ routine is out of ANSI-C standard.
+*/
+
+#if _VOLUMES
+static
+FATFS *FatFs[_VOLUMES]; /* Pointer to the file system objects (logical drives) */
+#else
+#error Number of volumes must not be 0.
+#endif
+
+static
+WORD Fsid; /* File system mount ID */
+
+#if _FS_RPATH
+static
+BYTE CurrVol; /* Current drive */
+#endif
+
+#if _FS_SHARE
+static
+FILESEM Files[_FS_SHARE]; /* File lock semaphores */
+#endif
+
+#if _USE_LFN == 0 /* No LFN feature */
+#define DEF_NAMEBUF BYTE sfn[12]
+#define INIT_BUF(dobj) (dobj).fn = sfn
+#define FREE_BUF()
+
+#elif _USE_LFN == 1 /* LFN feature with static working buffer */
+static WCHAR LfnBuf[_MAX_LFN+1];
+#define DEF_NAMEBUF BYTE sfn[12]
+#define INIT_BUF(dobj) { (dobj).fn = sfn; (dobj).lfn = LfnBuf; }
+#define FREE_BUF()
+
+#elif _USE_LFN == 2 /* LFN feature with dynamic working buffer on the stack */
+#define DEF_NAMEBUF BYTE sfn[12]; WCHAR lbuf[_MAX_LFN+1]
+#define INIT_BUF(dobj) { (dobj).fn = sfn; (dobj).lfn = lbuf; }
+#define FREE_BUF()
+
+#elif _USE_LFN == 3 /* LFN feature with dynamic working buffer on the heap */
+#define DEF_NAMEBUF BYTE sfn[12]; WCHAR *lfn
+#define INIT_BUF(dobj) { lfn = ff_memalloc((_MAX_LFN + 1) * 2); \
+ if (!lfn) LEAVE_FF((dobj).fs, FR_NOT_ENOUGH_CORE); \
+ (dobj).lfn = lfn; (dobj).fn = sfn; }
+#define FREE_BUF() ff_memfree(lfn)
+
+#else
+#error Wrong LFN configuration.
+#endif
+
+
+
+
+/*--------------------------------------------------------------------------
+
+ Module Private Functions
+
+---------------------------------------------------------------------------*/
+
+
+/*-----------------------------------------------------------------------*/
+/* String functions */
+/*-----------------------------------------------------------------------*/
+
+/* Copy memory to memory */
+static
+void mem_cpy (void* dst, const void* src, UINT cnt) {
+ BYTE *d = (BYTE*)dst;
+ const BYTE *s = (const BYTE*)src;
+
+#if _WORD_ACCESS == 1
+ while (cnt >= sizeof(int)) {
+ *(int*)d = *(int*)s;
+ d += sizeof(int); s += sizeof(int);
+ cnt -= sizeof(int);
+ }
+#endif
+ while (cnt--)
+ *d++ = *s++;
+}
+
+/* Fill memory */
+static
+void mem_set (void* dst, int val, UINT cnt) {
+ BYTE *d = (BYTE*)dst;
+
+ while (cnt--)
+ *d++ = (BYTE)val;
+}
+
+/* Compare memory to memory */
+static
+int mem_cmp (const void* dst, const void* src, UINT cnt) {
+ const BYTE *d = (const BYTE *)dst, *s = (const BYTE *)src;
+ int r = 0;
+
+ while (cnt-- && (r = *d++ - *s++) == 0) ;
+ return r;
+}
+
+/* Check if chr is contained in the string */
+static
+int chk_chr (const char* str, int chr) {
+ while (*str && *str != chr) str++;
+ return *str;
+}
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Request/Release grant to access the volume */
+/*-----------------------------------------------------------------------*/
+#if _FS_REENTRANT
+
+static
+int lock_fs (
+ FATFS *fs /* File system object */
+)
+{
+ return ff_req_grant(fs->sobj);
+}
+
+
+static
+void unlock_fs (
+ FATFS *fs, /* File system object */
+ FRESULT res /* Result code to be returned */
+)
+{
+ if (res != FR_NOT_ENABLED &&
+ res != FR_INVALID_DRIVE &&
+ res != FR_INVALID_OBJECT &&
+ res != FR_TIMEOUT) {
+ ff_rel_grant(fs->sobj);
+ }
+}
+#endif
+
+
+
+/*-----------------------------------------------------------------------*/
+/* File shareing control functions */
+/*-----------------------------------------------------------------------*/
+#if _FS_SHARE
+
+static
+FRESULT chk_lock ( /* Check if the file can be accessed */
+ FATFS_DIR* dj, /* Directory object pointing the file to be checked */
+ int acc /* Desired access (0:Read, 1:Write, 2:Delete/Rename) */
+)
+{
+ UINT i, be;
+
+ /* Search file semaphore table */
+ for (i = be = 0; i < _FS_SHARE; i++) {
+ if (Files[i].fs) { /* Existing entry */
+ if (Files[i].fs == dj->fs && /* Check if the file matched with an open file */
+ Files[i].clu == dj->sclust &&
+ Files[i].idx == dj->index) break;
+ } else { /* Blank entry */
+ be++;
+ }
+ }
+ if (i == _FS_SHARE) /* The file is not opened */
+ return (be || acc == 2) ? FR_OK : FR_TOO_MANY_OPEN_FILES; /* Is there a blank entry for new file? */
+
+ /* The file has been opened. Reject any open against writing file and all write mode open */
+ return (acc || Files[i].ctr == 0x100) ? FR_LOCKED : FR_OK;
+}
+
+
+static
+int enq_lock (void) /* Check if an entry is available for a new file */
+{
+ UINT i;
+
+ for (i = 0; i < _FS_SHARE && Files[i].fs; i++) ;
+ return (i == _FS_SHARE) ? 0 : 1;
+}
+
+
+static
+UINT inc_lock ( /* Increment file open counter and returns its index (0:int error) */
+ FATFS_DIR* dj, /* Directory object pointing the file to register or increment */
+ int acc /* Desired access mode (0:Read, !0:Write) */
+)
+{
+ UINT i;
+
+
+ for (i = 0; i < _FS_SHARE; i++) { /* Find the file */
+ if (Files[i].fs == dj->fs &&
+ Files[i].clu == dj->sclust &&
+ Files[i].idx == dj->index) break;
+ }
+
+ if (i == _FS_SHARE) { /* Not opened. Register it as new. */
+ for (i = 0; i < _FS_SHARE && Files[i].fs; i++) ;
+ if (i == _FS_SHARE) return 0; /* No space to register (int err) */
+ Files[i].fs = dj->fs;
+ Files[i].clu = dj->sclust;
+ Files[i].idx = dj->index;
+ Files[i].ctr = 0;
+ }
+
+ if (acc && Files[i].ctr) return 0; /* Access violation (int err) */
+
+ Files[i].ctr = acc ? 0x100 : Files[i].ctr + 1; /* Set semaphore value */
+
+ return i + 1;
+}
+
+
+static
+FRESULT dec_lock ( /* Decrement file open counter */
+ UINT i /* Semaphore index */
+)
+{
+ WORD n;
+ FRESULT res;
+
+
+ if (--i < _FS_SHARE) {
+ n = Files[i].ctr;
+ if (n == 0x100) n = 0;
+ if (n) n--;
+ Files[i].ctr = n;
+ if (!n) Files[i].fs = 0;
+ res = FR_OK;
+ } else {
+ res = FR_INT_ERR;
+ }
+ return res;
+}
+
+
+static
+void clear_lock ( /* Clear lock entries of the volume */
+ FATFS *fs
+)
+{
+ UINT i;
+
+ for (i = 0; i < _FS_SHARE; i++) {
+ if (Files[i].fs == fs) Files[i].fs = 0;
+ }
+}
+#endif
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Change window offset */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT move_window (
+ FATFS *fs, /* File system object */
+ DWORD sector /* Sector number to make appearance in the fs->win[] */
+) /* Move to zero only writes back dirty window */
+{
+ DWORD wsect;
+
+
+ wsect = fs->winsect;
+ if (wsect != sector) { /* Changed current window */
+#if !_FS_READONLY
+ if (fs->wflag) { /* Write back dirty window if needed */
+ if (disk_write(fs->drv, fs->win, wsect, 1) != RES_OK)
+ return FR_DISK_ERR;
+ fs->wflag = 0;
+ if (wsect < (fs->fatbase + fs->fsize)) { /* In FAT area */
+ BYTE nf;
+ for (nf = fs->n_fats; nf > 1; nf--) { /* Reflect the change to all FAT copies */
+ wsect += fs->fsize;
+ disk_write(fs->drv, fs->win, wsect, 1);
+ }
+ }
+ }
+#endif
+ if (sector) {
+ if (disk_read(fs->drv, fs->win, sector, 1) != RES_OK)
+ return FR_DISK_ERR;
+ fs->winsect = sector;
+ }
+ }
+
+ return FR_OK;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Clean-up cached data */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY
+static
+FRESULT sync ( /* FR_OK: successful, FR_DISK_ERR: failed */
+ FATFS *fs /* File system object */
+)
+{
+ FRESULT res;
+
+
+ res = move_window(fs, 0);
+ if (res == FR_OK) {
+ /* Update FSInfo sector if needed */
+ if (fs->fs_type == FS_FAT32 && fs->fsi_flag) {
+ fs->winsect = 0;
+ /* Create FSInfo structure */
+ mem_set(fs->win, 0, 512);
+ ST_WORD(fs->win+BS_55AA, 0xAA55);
+ ST_DWORD(fs->win+FSI_LeadSig, 0x41615252);
+ ST_DWORD(fs->win+FSI_StrucSig, 0x61417272);
+ ST_DWORD(fs->win+FSI_Free_Count, fs->free_clust);
+ ST_DWORD(fs->win+FSI_Nxt_Free, fs->last_clust);
+ /* Write it into the FSInfo sector */
+ disk_write(fs->drv, fs->win, fs->fsi_sector, 1);
+ fs->fsi_flag = 0;
+ }
+ /* Make sure that no pending write process in the physical drive */
+ if (disk_ioctl(fs->drv, CTRL_SYNC, 0) != RES_OK)
+ res = FR_DISK_ERR;
+ }
+
+ return res;
+}
+#endif
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Get sector# from cluster# */
+/*-----------------------------------------------------------------------*/
+
+
+DWORD clust2sect ( /* !=0: Sector number, 0: Failed - invalid cluster# */
+ FATFS *fs, /* File system object */
+ DWORD clst /* Cluster# to be converted */
+)
+{
+ clst -= 2;
+ if (clst >= (fs->n_fatent - 2)) return 0; /* Invalid cluster# */
+ return clst * fs->csize + fs->database;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* FAT access - Read value of a FAT entry */
+/*-----------------------------------------------------------------------*/
+
+
+DWORD get_fat ( /* 0xFFFFFFFF:Disk error, 1:Internal error, Else:Cluster status */
+ FATFS *fs, /* File system object */
+ DWORD clst /* Cluster# to get the link information */
+)
+{
+ UINT wc, bc;
+ BYTE *p;
+
+
+ if (clst < 2 || clst >= fs->n_fatent) /* Chack range */
+ return 1;
+
+ switch (fs->fs_type) {
+ case FS_FAT12 :
+ bc = (UINT)clst; bc += bc / 2;
+ if (move_window(fs, fs->fatbase + (bc / SS(fs)))) break;
+ wc = fs->win[bc % SS(fs)]; bc++;
+ if (move_window(fs, fs->fatbase + (bc / SS(fs)))) break;
+ wc |= fs->win[bc % SS(fs)] << 8;
+ return (clst & 1) ? (wc >> 4) : (wc & 0xFFF);
+
+ case FS_FAT16 :
+ if (move_window(fs, fs->fatbase + (clst / (SS(fs) / 2)))) break;
+ p = &fs->win[clst * 2 % SS(fs)];
+ return LD_WORD(p);
+
+ case FS_FAT32 :
+ if (move_window(fs, fs->fatbase + (clst / (SS(fs) / 4)))) break;
+ p = &fs->win[clst * 4 % SS(fs)];
+ return LD_DWORD(p) & 0x0FFFFFFF;
+ }
+
+ return 0xFFFFFFFF; /* An error occurred at the disk I/O layer */
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* FAT access - Change value of a FAT entry */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY
+
+FRESULT put_fat (
+ FATFS *fs, /* File system object */
+ DWORD clst, /* Cluster# to be changed in range of 2 to fs->n_fatent - 1 */
+ DWORD val /* New value to mark the cluster */
+)
+{
+ UINT bc;
+ BYTE *p;
+ FRESULT res;
+
+
+ if (clst < 2 || clst >= fs->n_fatent) { /* Check range */
+ res = FR_INT_ERR;
+
+ } else {
+ switch (fs->fs_type) {
+ case FS_FAT12 :
+ bc = clst; bc += bc / 2;
+ res = move_window(fs, fs->fatbase + (bc / SS(fs)));
+ if (res != FR_OK) break;
+ p = &fs->win[bc % SS(fs)];
+ *p = (clst & 1) ? ((*p & 0x0F) | ((BYTE)val << 4)) : (BYTE)val;
+ bc++;
+ fs->wflag = 1;
+ res = move_window(fs, fs->fatbase + (bc / SS(fs)));
+ if (res != FR_OK) break;
+ p = &fs->win[bc % SS(fs)];
+ *p = (clst & 1) ? (BYTE)(val >> 4) : ((*p & 0xF0) | ((BYTE)(val >> 8) & 0x0F));
+ break;
+
+ case FS_FAT16 :
+ res = move_window(fs, fs->fatbase + (clst / (SS(fs) / 2)));
+ if (res != FR_OK) break;
+ p = &fs->win[clst * 2 % SS(fs)];
+ ST_WORD(p, (WORD)val);
+ break;
+
+ case FS_FAT32 :
+ res = move_window(fs, fs->fatbase + (clst / (SS(fs) / 4)));
+ if (res != FR_OK) break;
+ p = &fs->win[clst * 4 % SS(fs)];
+ val |= LD_DWORD(p) & 0xF0000000;
+ ST_DWORD(p, val);
+ break;
+
+ default :
+ res = FR_INT_ERR;
+ }
+ fs->wflag = 1;
+ }
+
+ return res;
+}
+#endif /* !_FS_READONLY */
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* FAT handling - Remove a cluster chain */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY
+static
+FRESULT remove_chain (
+ FATFS *fs, /* File system object */
+ DWORD clst /* Cluster# to remove a chain from */
+)
+{
+ FRESULT res;
+ DWORD nxt;
+#if _USE_ERASE
+ DWORD scl = clst, ecl = clst, resion[2];
+#endif
+
+ if (clst < 2 || clst >= fs->n_fatent) { /* Check range */
+ res = FR_INT_ERR;
+
+ } else {
+ res = FR_OK;
+ while (clst < fs->n_fatent) { /* Not a last link? */
+ nxt = get_fat(fs, clst); /* Get cluster status */
+ if (nxt == 0) break; /* Empty cluster? */
+ if (nxt == 1) { res = FR_INT_ERR; break; } /* Internal error? */
+ if (nxt == 0xFFFFFFFF) { res = FR_DISK_ERR; break; } /* Disk error? */
+ res = put_fat(fs, clst, 0); /* Mark the cluster "empty" */
+ if (res != FR_OK) break;
+ if (fs->free_clust != 0xFFFFFFFF) { /* Update FSInfo */
+ fs->free_clust++;
+ fs->fsi_flag = 1;
+ }
+#if _USE_ERASE
+ if (ecl + 1 == nxt) { /* Next cluster is contiguous */
+ ecl = nxt;
+ } else { /* End of contiguous clusters */
+ resion[0] = clust2sect(fs, scl); /* Start sector */
+ resion[1] = clust2sect(fs, ecl) + fs->csize - 1; /* End sector */
+ disk_ioctl(fs->drv, CTRL_ERASE_SECTOR, resion); /* Erase the block */
+ scl = ecl = nxt;
+ }
+#endif
+ clst = nxt; /* Next cluster */
+ }
+ }
+
+ return res;
+}
+#endif
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* FAT handling - Stretch or Create a cluster chain */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY
+static
+DWORD create_chain ( /* 0:No free cluster, 1:Internal error, 0xFFFFFFFF:Disk error, >=2:New cluster# */
+ FATFS *fs, /* File system object */
+ DWORD clst /* Cluster# to stretch. 0 means create a new chain. */
+)
+{
+ DWORD cs, ncl, scl;
+ FRESULT res;
+
+
+ if (clst == 0) { /* Create a new chain */
+ scl = fs->last_clust; /* Get suggested start point */
+ if (!scl || scl >= fs->n_fatent) scl = 1;
+ }
+ else { /* Stretch the current chain */
+ cs = get_fat(fs, clst); /* Check the cluster status */
+ if (cs < 2) return 1; /* It is an invalid cluster */
+ if (cs < fs->n_fatent) return cs; /* It is already followed by next cluster */
+ scl = clst;
+ }
+
+ ncl = scl; /* Start cluster */
+ for (;;) {
+ ncl++; /* Next cluster */
+ if (ncl >= fs->n_fatent) { /* Wrap around */
+ ncl = 2;
+ if (ncl > scl) return 0; /* No free cluster */
+ }
+ cs = get_fat(fs, ncl); /* Get the cluster status */
+ if (cs == 0) break; /* Found a free cluster */
+ if (cs == 0xFFFFFFFF || cs == 1)/* An error occurred */
+ return cs;
+ if (ncl == scl) return 0; /* No free cluster */
+ }
+
+ res = put_fat(fs, ncl, 0x0FFFFFFF); /* Mark the new cluster "last link" */
+ if (res == FR_OK && clst != 0) {
+ res = put_fat(fs, clst, ncl); /* Link it to the previous one if needed */
+ }
+ if (res == FR_OK) {
+ fs->last_clust = ncl; /* Update FSINFO */
+ if (fs->free_clust != 0xFFFFFFFF) {
+ fs->free_clust--;
+ fs->fsi_flag = 1;
+ }
+ } else {
+ ncl = (res == FR_DISK_ERR) ? 0xFFFFFFFF : 1;
+ }
+
+ return ncl; /* Return new cluster number or error code */
+}
+#endif /* !_FS_READONLY */
+
+
+
+/*-----------------------------------------------------------------------*/
+/* FAT handling - Convert offset into cluster with link map table */
+/*-----------------------------------------------------------------------*/
+
+#if _USE_FASTSEEK
+static
+DWORD clmt_clust ( /* <2:Error, >=2:Cluster number */
+ FIL* fp, /* Pointer to the file object */
+ DWORD ofs /* File offset to be converted to cluster# */
+)
+{
+ DWORD cl, ncl, *tbl;
+
+
+ tbl = fp->cltbl + 1; /* Top of CLMT */
+ cl = ofs / SS(fp->fs) / fp->fs->csize; /* Cluster order from top of the file */
+ for (;;) {
+ ncl = *tbl++; /* Number of cluters in the fragment */
+ if (!ncl) return 0; /* End of table? (error) */
+ if (cl < ncl) break; /* In this fragment? */
+ cl -= ncl; tbl++; /* Next fragment */
+ }
+ return cl + *tbl; /* Return the cluster number */
+}
+#endif /* _USE_FASTSEEK */
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Directory handling - Set directory index */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT dir_sdi (
+ FATFS_DIR *dj, /* Pointer to directory object */
+ WORD idx /* Directory index number */
+)
+{
+ DWORD clst;
+ WORD ic;
+
+
+ dj->index = idx;
+ clst = dj->sclust;
+ if (clst == 1 || clst >= dj->fs->n_fatent) /* Check start cluster range */
+ return FR_INT_ERR;
+ if (!clst && dj->fs->fs_type == FS_FAT32) /* Replace cluster# 0 with root cluster# if in FAT32 */
+ clst = dj->fs->dirbase;
+
+ if (clst == 0) { /* Static table (root-dir in FAT12/16) */
+ dj->clust = clst;
+ if (idx >= dj->fs->n_rootdir) /* Index is out of range */
+ return FR_INT_ERR;
+ dj->sect = dj->fs->dirbase + idx / (SS(dj->fs) / SZ_DIR); /* Sector# */
+ }
+ else { /* Dynamic table (sub-dirs or root-dir in FAT32) */
+ ic = SS(dj->fs) / SZ_DIR * dj->fs->csize; /* Entries per cluster */
+ while (idx >= ic) { /* Follow cluster chain */
+ clst = get_fat(dj->fs, clst); /* Get next cluster */
+ if (clst == 0xFFFFFFFF) return FR_DISK_ERR; /* Disk error */
+ if (clst < 2 || clst >= dj->fs->n_fatent) /* Reached to end of table or int error */
+ return FR_INT_ERR;
+ idx -= ic;
+ }
+ dj->clust = clst;
+ dj->sect = clust2sect(dj->fs, clst) + idx / (SS(dj->fs) / SZ_DIR); /* Sector# */
+ }
+
+ dj->dir = dj->fs->win + (idx % (SS(dj->fs) / SZ_DIR)) * SZ_DIR; /* Ptr to the entry in the sector */
+
+ return FR_OK; /* Seek succeeded */
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Directory handling - Move directory index next */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT dir_next ( /* FR_OK:Succeeded, FR_NO_FILE:End of table, FR_DENIED:EOT and could not stretch */
+ FATFS_DIR *dj, /* Pointer to directory object */
+ int stretch /* 0: Do not stretch table, 1: Stretch table if needed */
+)
+{
+ DWORD clst;
+ WORD i;
+
+
+ stretch = stretch; /* To suppress warning on read-only cfg. */
+ i = dj->index + 1;
+ if (!i || !dj->sect) /* Report EOT when index has reached 65535 */
+ return FR_NO_FILE;
+
+ if (!(i % (SS(dj->fs) / SZ_DIR))) { /* Sector changed? */
+ dj->sect++; /* Next sector */
+
+ if (dj->clust == 0) { /* Static table */
+ if (i >= dj->fs->n_rootdir) /* Report EOT when end of table */
+ return FR_NO_FILE;
+ }
+ else { /* Dynamic table */
+ if (((i / (SS(dj->fs) / SZ_DIR)) & (dj->fs->csize - 1)) == 0) { /* Cluster changed? */
+ clst = get_fat(dj->fs, dj->clust); /* Get next cluster */
+ if (clst <= 1) return FR_INT_ERR;
+ if (clst == 0xFFFFFFFF) return FR_DISK_ERR;
+ if (clst >= dj->fs->n_fatent) { /* When it reached end of dynamic table */
+#if !_FS_READONLY
+ BYTE c;
+ if (!stretch) return FR_NO_FILE; /* When do not stretch, report EOT */
+ clst = create_chain(dj->fs, dj->clust); /* Stretch cluster chain */
+ if (clst == 0) return FR_DENIED; /* No free cluster */
+ if (clst == 1) return FR_INT_ERR;
+ if (clst == 0xFFFFFFFF) return FR_DISK_ERR;
+ /* Clean-up stretched table */
+ if (move_window(dj->fs, 0)) return FR_DISK_ERR; /* Flush active window */
+ mem_set(dj->fs->win, 0, SS(dj->fs)); /* Clear window buffer */
+ dj->fs->winsect = clust2sect(dj->fs, clst); /* Cluster start sector */
+ for (c = 0; c < dj->fs->csize; c++) { /* Fill the new cluster with 0 */
+ dj->fs->wflag = 1;
+ if (move_window(dj->fs, 0)) return FR_DISK_ERR;
+ dj->fs->winsect++;
+ }
+ dj->fs->winsect -= c; /* Rewind window address */
+#else
+ return FR_NO_FILE; /* Report EOT */
+#endif
+ }
+ dj->clust = clst; /* Initialize data for new cluster */
+ dj->sect = clust2sect(dj->fs, clst);
+ }
+ }
+ }
+
+ dj->index = i;
+ dj->dir = dj->fs->win + (i % (SS(dj->fs) / SZ_DIR)) * SZ_DIR;
+
+ return FR_OK;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* LFN handling - Test/Pick/Fit an LFN segment from/to directory entry */
+/*-----------------------------------------------------------------------*/
+#if _USE_LFN
+static
+const BYTE LfnOfs[] = {1,3,5,7,9,14,16,18,20,22,24,28,30}; /* Offset of LFN chars in the directory entry */
+
+
+static
+int cmp_lfn ( /* 1:Matched, 0:Not matched */
+ WCHAR *lfnbuf, /* Pointer to the LFN to be compared */
+ BYTE *dir /* Pointer to the directory entry containing a part of LFN */
+)
+{
+ UINT i, s;
+ WCHAR wc, uc;
+
+
+ i = ((dir[LDIR_Ord] & ~LLE) - 1) * 13; /* Get offset in the LFN buffer */
+ s = 0; wc = 1;
+ do {
+ uc = LD_WORD(dir+LfnOfs[s]); /* Pick an LFN character from the entry */
+ if (wc) { /* Last char has not been processed */
+ wc = ff_wtoupper(uc); /* Convert it to upper case */
+ if (i >= _MAX_LFN || wc != ff_wtoupper(lfnbuf[i++])) /* Compare it */
+ return 0; /* Not matched */
+ } else {
+ if (uc != 0xFFFF) return 0; /* Check filler */
+ }
+ } while (++s < 13); /* Repeat until all chars in the entry are checked */
+
+ if ((dir[LDIR_Ord] & LLE) && wc && lfnbuf[i]) /* Last segment matched but different length */
+ return 0;
+
+ return 1; /* The part of LFN matched */
+}
+
+
+
+static
+int pick_lfn ( /* 1:Succeeded, 0:Buffer overflow */
+ WCHAR *lfnbuf, /* Pointer to the Unicode-LFN buffer */
+ BYTE *dir /* Pointer to the directory entry */
+)
+{
+ UINT i, s;
+ WCHAR wc, uc;
+
+
+ i = ((dir[LDIR_Ord] & 0x3F) - 1) * 13; /* Offset in the LFN buffer */
+
+ s = 0; wc = 1;
+ do {
+ uc = LD_WORD(dir+LfnOfs[s]); /* Pick an LFN character from the entry */
+ if (wc) { /* Last char has not been processed */
+ if (i >= _MAX_LFN) return 0; /* Buffer overflow? */
+ lfnbuf[i++] = wc = uc; /* Store it */
+ } else {
+ if (uc != 0xFFFF) return 0; /* Check filler */
+ }
+ } while (++s < 13); /* Read all character in the entry */
+
+ if (dir[LDIR_Ord] & LLE) { /* Put terminator if it is the last LFN part */
+ if (i >= _MAX_LFN) return 0; /* Buffer overflow? */
+ lfnbuf[i] = 0;
+ }
+
+ return 1;
+}
+
+
+#if !_FS_READONLY
+static
+void fit_lfn (
+ const WCHAR *lfnbuf, /* Pointer to the LFN buffer */
+ BYTE *dir, /* Pointer to the directory entry */
+ BYTE ord, /* LFN order (1-20) */
+ BYTE sum /* SFN sum */
+)
+{
+ UINT i, s;
+ WCHAR wc;
+
+
+ dir[LDIR_Chksum] = sum; /* Set check sum */
+ dir[LDIR_Attr] = AM_LFN; /* Set attribute. LFN entry */
+ dir[LDIR_Type] = 0;
+ ST_WORD(dir+LDIR_FstClusLO, 0);
+
+ i = (ord - 1) * 13; /* Get offset in the LFN buffer */
+ s = wc = 0;
+ do {
+ if (wc != 0xFFFF) wc = lfnbuf[i++]; /* Get an effective char */
+ ST_WORD(dir+LfnOfs[s], wc); /* Put it */
+ if (!wc) wc = 0xFFFF; /* Padding chars following last char */
+ } while (++s < 13);
+ if (wc == 0xFFFF || !lfnbuf[i]) ord |= LLE; /* Bottom LFN part is the start of LFN sequence */
+ dir[LDIR_Ord] = ord; /* Set the LFN order */
+}
+
+#endif
+#endif
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Create numbered name */
+/*-----------------------------------------------------------------------*/
+#if _USE_LFN
+void gen_numname (
+ BYTE *dst, /* Pointer to generated SFN */
+ const BYTE *src, /* Pointer to source SFN to be modified */
+ const WCHAR *lfn, /* Pointer to LFN */
+ WORD seq /* Sequence number */
+)
+{
+ BYTE ns[8], c;
+ UINT i, j;
+
+
+ mem_cpy(dst, src, 11);
+
+ if (seq > 5) { /* On many collisions, generate a hash number instead of sequential number */
+ do seq = (seq >> 1) + (seq << 15) + (WORD)*lfn++; while (*lfn);
+ }
+
+ /* itoa (hexdecimal) */
+ i = 7;
+ do {
+ c = (seq % 16) + '0';
+ if (c > '9') c += 7;
+ ns[i--] = c;
+ seq /= 16;
+ } while (seq);
+ ns[i] = '~';
+
+ /* Append the number */
+ for (j = 0; j < i && dst[j] != ' '; j++) {
+ if (IsDBCS1(dst[j])) {
+ if (j == i - 1) break;
+ j++;
+ }
+ }
+ do {
+ dst[j++] = (i < 8) ? ns[i++] : ' ';
+ } while (j < 8);
+}
+#endif
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Calculate sum of an SFN */
+/*-----------------------------------------------------------------------*/
+#if _USE_LFN
+static
+BYTE sum_sfn (
+ const BYTE *dir /* Ptr to directory entry */
+)
+{
+ BYTE sum = 0;
+ UINT n = 11;
+
+ do sum = (sum >> 1) + (sum << 7) + *dir++; while (--n);
+ return sum;
+}
+#endif
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Directory handling - Find an object in the directory */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT dir_find (
+ FATFS_DIR *dj /* Pointer to the directory object linked to the file name */
+)
+{
+ FRESULT res;
+ BYTE c, *dir;
+#if _USE_LFN
+ BYTE a, ord, sum;
+#endif
+
+ res = dir_sdi(dj, 0); /* Rewind directory object */
+ if (res != FR_OK) return res;
+
+#if _USE_LFN
+ ord = sum = 0xFF;
+#endif
+ do {
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ dir = dj->dir; /* Ptr to the directory entry of current index */
+ c = dir[DIR_Name];
+ if (c == 0) { res = FR_NO_FILE; break; } /* Reached to end of table */
+#if _USE_LFN /* LFN configuration */
+ a = dir[DIR_Attr] & AM_MASK;
+ if (c == DDE || ((a & AM_VOL) && a != AM_LFN)) { /* An entry without valid data */
+ ord = 0xFF;
+ } else {
+ if (a == AM_LFN) { /* An LFN entry is found */
+ if (dj->lfn) {
+ if (c & LLE) { /* Is it start of LFN sequence? */
+ sum = dir[LDIR_Chksum];
+ c &= ~LLE; ord = c; /* LFN start order */
+ dj->lfn_idx = dj->index;
+ }
+ /* Check validity of the LFN entry and compare it with given name */
+ ord = (c == ord && sum == dir[LDIR_Chksum] && cmp_lfn(dj->lfn, dir)) ? ord - 1 : 0xFF;
+ }
+ } else { /* An SFN entry is found */
+ if (!ord && sum == sum_sfn(dir)) break; /* LFN matched? */
+ ord = 0xFF; dj->lfn_idx = 0xFFFF; /* Reset LFN sequence */
+ if (!(dj->fn[NS] & NS_LOSS) && !mem_cmp(dir, dj->fn, 11)) break; /* SFN matched? */
+ }
+ }
+#else /* Non LFN configuration */
+ if (!(dir[DIR_Attr] & AM_VOL) && !mem_cmp(dir, dj->fn, 11)) /* Is it a valid entry? */
+ break;
+#endif
+ res = dir_next(dj, 0); /* Next entry */
+ } while (res == FR_OK);
+
+ return res;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Read an object from the directory */
+/*-----------------------------------------------------------------------*/
+#if _FS_MINIMIZE <= 1
+static
+FRESULT dir_read (
+ FATFS_DIR *dj /* Pointer to the directory object that pointing the entry to be read */
+)
+{
+ FRESULT res;
+ BYTE c, *dir;
+#if _USE_LFN
+ BYTE a, ord = 0xFF, sum = 0xFF;
+#endif
+
+ res = FR_NO_FILE;
+ while (dj->sect) {
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ dir = dj->dir; /* Ptr to the directory entry of current index */
+ c = dir[DIR_Name];
+ if (c == 0) { res = FR_NO_FILE; break; } /* Reached to end of table */
+#if _USE_LFN /* LFN configuration */
+ a = dir[DIR_Attr] & AM_MASK;
+ if (c == DDE || (!_FS_RPATH && c == '.') || ((a & AM_VOL) && a != AM_LFN)) { /* An entry without valid data */
+ ord = 0xFF;
+ } else {
+ if (a == AM_LFN) { /* An LFN entry is found */
+ if (c & LLE) { /* Is it start of LFN sequence? */
+ sum = dir[LDIR_Chksum];
+ c &= ~LLE; ord = c;
+ dj->lfn_idx = dj->index;
+ }
+ /* Check LFN validity and capture it */
+ ord = (c == ord && sum == dir[LDIR_Chksum] && pick_lfn(dj->lfn, dir)) ? ord - 1 : 0xFF;
+ } else { /* An SFN entry is found */
+ if (ord || sum != sum_sfn(dir)) /* Is there a valid LFN? */
+ dj->lfn_idx = 0xFFFF; /* It has no LFN. */
+ break;
+ }
+ }
+#else /* Non LFN configuration */
+ if (c != DDE && (_FS_RPATH || c != '.') && !(dir[DIR_Attr] & AM_VOL)) /* Is it a valid entry? */
+ break;
+#endif
+ res = dir_next(dj, 0); /* Next entry */
+ if (res != FR_OK) break;
+ }
+
+ if (res != FR_OK) dj->sect = 0;
+
+ return res;
+}
+#endif
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Register an object to the directory */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY
+static
+FRESULT dir_register ( /* FR_OK:Successful, FR_DENIED:No free entry or too many SFN collision, FR_DISK_ERR:Disk error */
+ FATFS_DIR *dj /* Target directory with object name to be created */
+)
+{
+ FRESULT res;
+ BYTE c, *dir;
+#if _USE_LFN /* LFN configuration */
+ WORD n, ne, is;
+ BYTE sn[12], *fn, sum;
+ WCHAR *lfn;
+
+
+ fn = dj->fn; lfn = dj->lfn;
+ mem_cpy(sn, fn, 12);
+
+ if (_FS_RPATH && (sn[NS] & NS_DOT)) /* Cannot create dot entry */
+ return FR_INVALID_NAME;
+
+ if (sn[NS] & NS_LOSS) { /* When LFN is out of 8.3 format, generate a numbered name */
+ fn[NS] = 0; dj->lfn = 0; /* Find only SFN */
+ for (n = 1; n < 100; n++) {
+ gen_numname(fn, sn, lfn, n); /* Generate a numbered name */
+ res = dir_find(dj); /* Check if the name collides with existing SFN */
+ if (res != FR_OK) break;
+ }
+ if (n == 100) return FR_DENIED; /* Abort if too many collisions */
+ if (res != FR_NO_FILE) return res; /* Abort if the result is other than 'not collided' */
+ fn[NS] = sn[NS]; dj->lfn = lfn;
+ }
+
+ if (sn[NS] & NS_LFN) { /* When LFN is to be created, reserve an SFN + LFN entries. */
+ for (ne = 0; lfn[ne]; ne++) ;
+ ne = (ne + 25) / 13;
+ } else { /* Otherwise reserve only an SFN entry. */
+ ne = 1;
+ }
+
+ /* Reserve contiguous entries */
+ res = dir_sdi(dj, 0);
+ if (res != FR_OK) return res;
+ n = is = 0;
+ do {
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ c = *dj->dir; /* Check the entry status */
+ if (c == DDE || c == 0) { /* Is it a blank entry? */
+ if (n == 0) is = dj->index; /* First index of the contiguous entry */
+ if (++n == ne) break; /* A contiguous entry that required count is found */
+ } else {
+ n = 0; /* Not a blank entry. Restart to search */
+ }
+ res = dir_next(dj, 1); /* Next entry with table stretch */
+ } while (res == FR_OK);
+
+ if (res == FR_OK && ne > 1) { /* Initialize LFN entry if needed */
+ res = dir_sdi(dj, is);
+ if (res == FR_OK) {
+ sum = sum_sfn(dj->fn); /* Sum of the SFN tied to the LFN */
+ ne--;
+ do { /* Store LFN entries in bottom first */
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ fit_lfn(dj->lfn, dj->dir, (BYTE)ne, sum);
+ dj->fs->wflag = 1;
+ res = dir_next(dj, 0); /* Next entry */
+ } while (res == FR_OK && --ne);
+ }
+ }
+
+#else /* Non LFN configuration */
+ res = dir_sdi(dj, 0);
+ if (res == FR_OK) {
+ do { /* Find a blank entry for the SFN */
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ c = *dj->dir;
+ if (c == DDE || c == 0) break; /* Is it a blank entry? */
+ res = dir_next(dj, 1); /* Next entry with table stretch */
+ } while (res == FR_OK);
+ }
+#endif
+
+ if (res == FR_OK) { /* Initialize the SFN entry */
+ res = move_window(dj->fs, dj->sect);
+ if (res == FR_OK) {
+ dir = dj->dir;
+ mem_set(dir, 0, SZ_DIR); /* Clean the entry */
+ mem_cpy(dir, dj->fn, 11); /* Put SFN */
+#if _USE_LFN
+ dir[DIR_NTres] = *(dj->fn+NS) & (NS_BODY | NS_EXT); /* Put NT flag */
+#endif
+ dj->fs->wflag = 1;
+ }
+ }
+
+ return res;
+}
+#endif /* !_FS_READONLY */
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Remove an object from the directory */
+/*-----------------------------------------------------------------------*/
+#if !_FS_READONLY && !_FS_MINIMIZE
+static
+FRESULT dir_remove ( /* FR_OK: Successful, FR_DISK_ERR: A disk error */
+ FATFS_DIR *dj /* Directory object pointing the entry to be removed */
+)
+{
+ FRESULT res;
+#if _USE_LFN /* LFN configuration */
+ WORD i;
+
+ i = dj->index; /* SFN index */
+ res = dir_sdi(dj, (WORD)((dj->lfn_idx == 0xFFFF) ? i : dj->lfn_idx)); /* Goto the SFN or top of the LFN entries */
+ if (res == FR_OK) {
+ do {
+ res = move_window(dj->fs, dj->sect);
+ if (res != FR_OK) break;
+ *dj->dir = DDE; /* Mark the entry "deleted" */
+ dj->fs->wflag = 1;
+ if (dj->index >= i) break; /* When reached SFN, all entries of the object has been deleted. */
+ res = dir_next(dj, 0); /* Next entry */
+ } while (res == FR_OK);
+ if (res == FR_NO_FILE) res = FR_INT_ERR;
+ }
+
+#else /* Non LFN configuration */
+ res = dir_sdi(dj, dj->index);
+ if (res == FR_OK) {
+ res = move_window(dj->fs, dj->sect);
+ if (res == FR_OK) {
+ *dj->dir = DDE; /* Mark the entry "deleted" */
+ dj->fs->wflag = 1;
+ }
+ }
+#endif
+
+ return res;
+}
+#endif /* !_FS_READONLY */
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Pick a segment and create the object name in directory form */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT create_name (
+ FATFS_DIR *dj, /* Pointer to the directory object */
+ const TCHAR **path /* Pointer to pointer to the segment in the path string */
+)
+{
+#ifdef _EXCVT
+ static const BYTE excvt[] = _EXCVT; /* Upper conversion table for extended chars */
+#endif
+
+#if _USE_LFN /* LFN configuration */
+ BYTE b, cf;
+ WCHAR w, *lfn;
+ UINT i, ni, si, di;
+ const TCHAR *p;
+
+ /* Create LFN in Unicode */
+ for (p = *path; *p == '/' || *p == '\\'; p++) ; /* Strip duplicated separator */
+ lfn = dj->lfn;
+ si = di = 0;
+ for (;;) {
+ w = p[si++]; /* Get a character */
+ if (w < ' ' || w == '/' || w == '\\') break; /* Break on end of segment */
+ if (di >= _MAX_LFN) /* Reject too long name */
+ return FR_INVALID_NAME;
+#if !_LFN_UNICODE
+ w &= 0xFF;
+ if (IsDBCS1(w)) { /* Check if it is a DBC 1st byte (always false on SBCS cfg) */
+ b = (BYTE)p[si++]; /* Get 2nd byte */
+ if (!IsDBCS2(b))
+ return FR_INVALID_NAME; /* Reject invalid sequence */
+ w = (w << 8) + b; /* Create a DBC */
+ }
+ w = ff_convert(w, 1); /* Convert ANSI/OEM to Unicode */
+ if (!w) return FR_INVALID_NAME; /* Reject invalid code */
+#endif
+ if (w < 0x80 && chk_chr("\"*:<>\?|\x7F", w)) /* Reject illegal chars for LFN */
+ return FR_INVALID_NAME;
+ lfn[di++] = w; /* Store the Unicode char */
+ }
+ *path = &p[si]; /* Return pointer to the next segment */
+ cf = (w < ' ') ? NS_LAST : 0; /* Set last segment flag if end of path */
+#if _FS_RPATH
+ if ((di == 1 && lfn[di-1] == '.') || /* Is this a dot entry? */
+ (di == 2 && lfn[di-1] == '.' && lfn[di-2] == '.')) {
+ lfn[di] = 0;
+ for (i = 0; i < 11; i++)
+ dj->fn[i] = (i < di) ? '.' : ' ';
+ dj->fn[i] = cf | NS_DOT; /* This is a dot entry */
+ return FR_OK;
+ }
+#endif
+ while (di) { /* Strip trailing spaces and dots */
+ w = lfn[di-1];
+ if (w != ' ' && w != '.') break;
+ di--;
+ }
+ if (!di) return FR_INVALID_NAME; /* Reject nul string */
+
+ lfn[di] = 0; /* LFN is created */
+
+ /* Create SFN in directory form */
+ mem_set(dj->fn, ' ', 11);
+ for (si = 0; lfn[si] == ' ' || lfn[si] == '.'; si++) ; /* Strip leading spaces and dots */
+ if (si) cf |= NS_LOSS | NS_LFN;
+ while (di && lfn[di - 1] != '.') di--; /* Find extension (di<=si: no extension) */
+
+ b = i = 0; ni = 8;
+ for (;;) {
+ w = lfn[si++]; /* Get an LFN char */
+ if (!w) break; /* Break on end of the LFN */
+ if (w == ' ' || (w == '.' && si != di)) { /* Remove spaces and dots */
+ cf |= NS_LOSS | NS_LFN; continue;
+ }
+
+ if (i >= ni || si == di) { /* Extension or end of SFN */
+ if (ni == 11) { /* Long extension */
+ cf |= NS_LOSS | NS_LFN; break;
+ }
+ if (si != di) cf |= NS_LOSS | NS_LFN; /* Out of 8.3 format */
+ if (si > di) break; /* No extension */
+ si = di; i = 8; ni = 11; /* Enter extension section */
+ b <<= 2; continue;
+ }
+
+ if (w >= 0x80) { /* Non ASCII char */
+#ifdef _EXCVT
+ w = ff_convert(w, 0); /* Unicode -> OEM code */
+ if (w) w = excvt[w - 0x80]; /* Convert extended char to upper (SBCS) */
+#else
+ w = ff_convert(ff_wtoupper(w), 0); /* Upper converted Unicode -> OEM code */
+#endif
+ cf |= NS_LFN; /* Force create LFN entry */
+ }
+
+ if (_DF1S && w >= 0x100) { /* Double byte char (always false on SBCS cfg) */
+ if (i >= ni - 1) {
+ cf |= NS_LOSS | NS_LFN; i = ni; continue;
+ }
+ dj->fn[i++] = (BYTE)(w >> 8);
+ } else { /* Single byte char */
+ if (!w || chk_chr("+,;=[]", w)) { /* Replace illegal chars for SFN */
+ w = '_'; cf |= NS_LOSS | NS_LFN;/* Lossy conversion */
+ } else {
+ if (IsUpper(w)) { /* ASCII large capital */
+ b |= 2;
+ } else {
+ if (IsLower(w)) { /* ASCII small capital */
+ b |= 1; w -= 0x20;
+ }
+ }
+ }
+ }
+ dj->fn[i++] = (BYTE)w;
+ }
+
+ if (dj->fn[0] == DDE) dj->fn[0] = NDDE; /* If the first char collides with deleted mark, replace it with 0x05 */
+
+ if (ni == 8) b <<= 2;
+ if ((b & 0x0C) == 0x0C || (b & 0x03) == 0x03) /* Create LFN entry when there are composite capitals */
+ cf |= NS_LFN;
+ if (!(cf & NS_LFN)) { /* When LFN is in 8.3 format without extended char, NT flags are created */
+ if ((b & 0x03) == 0x01) cf |= NS_EXT; /* NT flag (Extension has only small capital) */
+ if ((b & 0x0C) == 0x04) cf |= NS_BODY; /* NT flag (Filename has only small capital) */
+ }
+
+ dj->fn[NS] = cf; /* SFN is created */
+
+ return FR_OK;
+
+
+#else /* Non-LFN configuration */
+ BYTE b, c, d, *sfn;
+ UINT ni, si, i;
+ const char *p;
+
+ /* Create file name in directory form */
+ for (p = *path; *p == '/' || *p == '\\'; p++) ; /* Strip duplicated separator */
+ sfn = dj->fn;
+ mem_set(sfn, ' ', 11);
+ si = i = b = 0; ni = 8;
+#if _FS_RPATH
+ if (p[si] == '.') { /* Is this a dot entry? */
+ for (;;) {
+ c = (BYTE)p[si++];
+ if (c != '.' || si >= 3) break;
+ sfn[i++] = c;
+ }
+ if (c != '/' && c != '\\' && c > ' ') return FR_INVALID_NAME;
+ *path = &p[si]; /* Return pointer to the next segment */
+ sfn[NS] = (c <= ' ') ? NS_LAST | NS_DOT : NS_DOT; /* Set last segment flag if end of path */
+ return FR_OK;
+ }
+#endif
+ for (;;) {
+ c = (BYTE)p[si++];
+ if (c <= ' ' || c == '/' || c == '\\') break; /* Break on end of segment */
+ if (c == '.' || i >= ni) {
+ if (ni != 8 || c != '.') return FR_INVALID_NAME;
+ i = 8; ni = 11;
+ b <<= 2; continue;
+ }
+ if (c >= 0x80) { /* Extended char? */
+ b |= 3; /* Eliminate NT flag */
+#ifdef _EXCVT
+ c = excvt[c-0x80]; /* Upper conversion (SBCS) */
+#else
+#if !_DF1S /* ASCII only cfg */
+ return FR_INVALID_NAME;
+#endif
+#endif
+ }
+ if (IsDBCS1(c)) { /* Check if it is a DBC 1st byte (always false on SBCS cfg) */
+ d = (BYTE)p[si++]; /* Get 2nd byte */
+ if (!IsDBCS2(d) || i >= ni - 1) /* Reject invalid DBC */
+ return FR_INVALID_NAME;
+ sfn[i++] = c;
+ sfn[i++] = d;
+ } else { /* Single byte code */
+ if (chk_chr("\"*+,:;<=>\?[]|\x7F", c)) /* Reject illegal chrs for SFN */
+ return FR_INVALID_NAME;
+ if (IsUpper(c)) { /* ASCII large capital? */
+ b |= 2;
+ } else {
+ if (IsLower(c)) { /* ASCII small capital? */
+ b |= 1; c -= 0x20;
+ }
+ }
+ sfn[i++] = c;
+ }
+ }
+ *path = &p[si]; /* Return pointer to the next segment */
+ c = (c <= ' ') ? NS_LAST : 0; /* Set last segment flag if end of path */
+
+ if (!i) return FR_INVALID_NAME; /* Reject nul string */
+ if (sfn[0] == DDE) sfn[0] = NDDE; /* When first char collides with DDE, replace it with 0x05 */
+
+ if (ni == 8) b <<= 2;
+ if ((b & 0x03) == 0x01) c |= NS_EXT; /* NT flag (Name extension has only small capital) */
+ if ((b & 0x0C) == 0x04) c |= NS_BODY; /* NT flag (Name body has only small capital) */
+
+ sfn[NS] = c; /* Store NT flag, File name is created */
+
+ return FR_OK;
+#endif
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Get file information from directory entry */
+/*-----------------------------------------------------------------------*/
+#if _FS_MINIMIZE <= 1
+static
+void get_fileinfo ( /* No return code */
+ FATFS_DIR *dj, /* Pointer to the directory object */
+ FILINFO *fno /* Pointer to the file information to be filled */
+)
+{
+ UINT i;
+ BYTE nt, *dir;
+ TCHAR *p, c;
+
+
+ p = fno->fname;
+ if (dj->sect) {
+ dir = dj->dir;
+ nt = dir[DIR_NTres]; /* NT flag */
+ for (i = 0; i < 8; i++) { /* Copy name body */
+ c = dir[i];
+ if (c == ' ') break;
+ if (c == NDDE) c = (TCHAR)DDE;
+ if (_USE_LFN && (nt & NS_BODY) && IsUpper(c)) c += 0x20;
+#if _LFN_UNICODE
+ if (IsDBCS1(c) && i < 7 && IsDBCS2(dir[i+1]))
+ c = (c << 8) | dir[++i];
+ c = ff_convert(c, 1);
+ if (!c) c = '?';
+#endif
+ *p++ = c;
+ }
+ if (dir[8] != ' ') { /* Copy name extension */
+ *p++ = '.';
+ for (i = 8; i < 11; i++) {
+ c = dir[i];
+ if (c == ' ') break;
+ if (_USE_LFN && (nt & NS_EXT) && IsUpper(c)) c += 0x20;
+#if _LFN_UNICODE
+ if (IsDBCS1(c) && i < 10 && IsDBCS2(dir[i+1]))
+ c = (c << 8) | dir[++i];
+ c = ff_convert(c, 1);
+ if (!c) c = '?';
+#endif
+ *p++ = c;
+ }
+ }
+ fno->fattrib = dir[DIR_Attr]; /* Attribute */
+ fno->fsize = LD_DWORD(dir+DIR_FileSize); /* Size */
+ fno->fdate = LD_WORD(dir+DIR_WrtDate); /* Date */
+ fno->ftime = LD_WORD(dir+DIR_WrtTime); /* Time */
+ }
+ *p = 0; /* Terminate SFN str by a \0 */
+
+#if _USE_LFN
+ if (fno->lfname && fno->lfsize) {
+ TCHAR *tp = fno->lfname;
+ WCHAR w, *lfn;
+
+ i = 0;
+ if (dj->sect && dj->lfn_idx != 0xFFFF) {/* Get LFN if available */
+ lfn = dj->lfn;
+ while ((w = *lfn++) != 0) { /* Get an LFN char */
+#if !_LFN_UNICODE
+ w = ff_convert(w, 0); /* Unicode -> OEM conversion */
+ if (!w) { i = 0; break; } /* Could not convert, no LFN */
+ if (_DF1S && w >= 0x100) /* Put 1st byte if it is a DBC (always false on SBCS cfg) */
+ tp[i++] = (TCHAR)(w >> 8);
+#endif
+ if (i >= fno->lfsize - 1) { i = 0; break; } /* Buffer overflow, no LFN */
+ tp[i++] = (TCHAR)w;
+ }
+ }
+ tp[i] = 0; /* Terminate the LFN str by a \0 */
+ }
+#endif
+}
+#endif /* _FS_MINIMIZE <= 1 */
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Follow a file path */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT follow_path ( /* FR_OK(0): successful, !=0: error code */
+ FATFS_DIR *dj, /* Directory object to return last directory and found object */
+ const TCHAR *path /* Full-path string to find a file or directory */
+)
+{
+ FRESULT res;
+ BYTE *dir, ns;
+
+
+#if _FS_RPATH
+ if (*path == '/' || *path == '\\') { /* There is a heading separator */
+ path++; dj->sclust = 0; /* Strip it and start from the root dir */
+ } else { /* No heading separator */
+ dj->sclust = dj->fs->cdir; /* Start from the current dir */
+ }
+#else
+ if (*path == '/' || *path == '\\') /* Strip heading separator if exist */
+ path++;
+ dj->sclust = 0; /* Start from the root dir */
+#endif
+
+ if ((UINT)*path < ' ') { /* Nul path means the start directory itself */
+ res = dir_sdi(dj, 0);
+ dj->dir = 0;
+
+ } else { /* Follow path */
+ for (;;) {
+ res = create_name(dj, &path); /* Get a segment */
+ if (res != FR_OK) break;
+ res = dir_find(dj); /* Find it */
+ ns = *(dj->fn+NS);
+ if (res != FR_OK) { /* Failed to find the object */
+ if (res != FR_NO_FILE) break; /* Abort if any hard error occured */
+ /* Object not found */
+ if (_FS_RPATH && (ns & NS_DOT)) { /* If dot entry is not exit */
+ dj->sclust = 0; dj->dir = 0; /* It is the root dir */
+ res = FR_OK;
+ if (!(ns & NS_LAST)) continue;
+ } else { /* Could not find the object */
+ if (!(ns & NS_LAST)) res = FR_NO_PATH;
+ }
+ break;
+ }
+ if (ns & NS_LAST) break; /* Last segment match. Function completed. */
+ dir = dj->dir; /* There is next segment. Follow the sub directory */
+ if (!(dir[DIR_Attr] & AM_DIR)) { /* Cannot follow because it is a file */
+ res = FR_NO_PATH; break;
+ }
+ dj->sclust = LD_CLUST(dir);
+ }
+ }
+
+ return res;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Load a sector and check if it is an FAT Volume Boot Record */
+/*-----------------------------------------------------------------------*/
+
+static
+BYTE check_fs ( /* 0:FAT-VBR, 1:Valid BR but not FAT, 2:Not a BR, 3:Disk error */
+ FATFS *fs, /* File system object */
+ DWORD sect /* Sector# (lba) to check if it is an FAT boot record or not */
+)
+{
+ if (disk_read(fs->drv, fs->win, sect, 1) != RES_OK) /* Load boot record */
+ return 3;
+ if (LD_WORD(&fs->win[BS_55AA]) != 0xAA55) /* Check record signature (always placed at offset 510 even if the sector size is >512) */
+ return 2;
+
+ if ((LD_DWORD(&fs->win[BS_FilSysType]) & 0xFFFFFF) == 0x544146) /* Check "FAT" string */
+ return 0;
+ if ((LD_DWORD(&fs->win[BS_FilSysType32]) & 0xFFFFFF) == 0x544146)
+ return 0;
+
+ return 1;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Check if the file system object is valid or not */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT chk_mounted ( /* FR_OK(0): successful, !=0: any error occurred */
+ const TCHAR **path, /* Pointer to pointer to the path name (drive number) */
+ FATFS **rfs, /* Pointer to pointer to the found file system object */
+ BYTE chk_wp /* !=0: Check media write protection for write access */
+)
+{
+ BYTE fmt, b, pi, *tbl;
+ UINT vol;
+ DSTATUS stat;
+ DWORD bsect, fasize, tsect, sysect, nclst, szbfat;
+ WORD nrsv;
+ const TCHAR *p = *path;
+ FATFS *fs;
+
+ /* Get logical drive number from the path name */
+ vol = p[0] - '0'; /* Is there a drive number? */
+ if (vol <= 9 && p[1] == ':') { /* Found a drive number, get and strip it */
+ p += 2; *path = p; /* Return pointer to the path name */
+ } else { /* No drive number is given */
+#if _FS_RPATH
+ vol = CurrVol; /* Use current drive */
+#else
+ vol = 0; /* Use drive 0 */
+#endif
+ }
+
+ /* Check if the file system object is valid or not */
+ if (vol >= _VOLUMES) /* Is the drive number valid? */
+ return FR_INVALID_DRIVE;
+ *rfs = fs = FatFs[vol]; /* Return pointer to the corresponding file system object */
+ if (!fs) return FR_NOT_ENABLED; /* Is the file system object available? */
+
+ ENTER_FF(fs); /* Lock file system */
+
+ if (fs->fs_type) { /* If the logical drive has been mounted */
+ stat = disk_status(fs->drv);
+ if (!(stat & STA_NOINIT)) { /* and the physical drive is kept initialized (has not been changed), */
+ if (!_FS_READONLY && chk_wp && (stat & STA_PROTECT)) /* Check write protection if needed */
+ return FR_WRITE_PROTECTED;
+ return FR_OK; /* The file system object is valid */
+ }
+ }
+
+ /* The file system object is not valid. */
+ /* Following code attempts to mount the volume. (analyze BPB and initialize the fs object) */
+
+ fs->fs_type = 0; /* Clear the file system object */
+ fs->drv = LD2PD(vol); /* Bind the logical drive and a physical drive */
+ stat = disk_initialize(fs->drv); /* Initialize low level disk I/O layer */
+ if (stat & STA_NOINIT) /* Check if the initialization succeeded */
+ return FR_NOT_READY; /* Failed to initialize due to no media or hard error */
+ if (!_FS_READONLY && chk_wp && (stat & STA_PROTECT)) /* Check disk write protection if needed */
+ return FR_WRITE_PROTECTED;
+#if _MAX_SS != 512 /* Get disk sector size (variable sector size cfg only) */
+ if (disk_ioctl(fs->drv, GET_SECTOR_SIZE, &fs->ssize) != RES_OK)
+ return FR_DISK_ERR;
+#endif
+ /* Search FAT partition on the drive. Supports only generic partitionings, FDISK and SFD. */
+ fmt = check_fs(fs, bsect = 0); /* Load sector 0 and check if it is an FAT-VBR (in SFD) */
+ if (LD2PT(vol) && !fmt) fmt = 1; /* Force non-SFD if the volume is forced partition */
+ if (fmt == 1) { /* Not an FAT-VBR, the physical drive can be partitioned */
+ /* Check the partition listed in the partition table */
+ pi = LD2PT(vol);
+ if (pi) pi--;
+ tbl = &fs->win[MBR_Table + pi * SZ_PTE];/* Partition table */
+ if (tbl[4]) { /* Is the partition existing? */
+ bsect = LD_DWORD(&tbl[8]); /* Partition offset in LBA */
+ fmt = check_fs(fs, bsect); /* Check the partition */
+ }
+ }
+ if (fmt == 3) return FR_DISK_ERR;
+ if (fmt) return FR_NO_FILESYSTEM; /* No FAT volume is found */
+
+ /* An FAT volume is found. Following code initializes the file system object */
+
+ if (LD_WORD(fs->win+BPB_BytsPerSec) != SS(fs)) /* (BPB_BytsPerSec must be equal to the physical sector size) */
+ return FR_NO_FILESYSTEM;
+
+ fasize = LD_WORD(fs->win+BPB_FATSz16); /* Number of sectors per FAT */
+ if (!fasize) fasize = LD_DWORD(fs->win+BPB_FATSz32);
+ fs->fsize = fasize;
+
+ fs->n_fats = b = fs->win[BPB_NumFATs]; /* Number of FAT copies */
+ if (b != 1 && b != 2) return FR_NO_FILESYSTEM; /* (Must be 1 or 2) */
+ fasize *= b; /* Number of sectors for FAT area */
+
+ fs->csize = b = fs->win[BPB_SecPerClus]; /* Number of sectors per cluster */
+ if (!b || (b & (b - 1))) return FR_NO_FILESYSTEM; /* (Must be power of 2) */
+
+ fs->n_rootdir = LD_WORD(fs->win+BPB_RootEntCnt); /* Number of root directory entries */
+ if (fs->n_rootdir % (SS(fs) / SZ_DIR)) return FR_NO_FILESYSTEM; /* (BPB_RootEntCnt must be sector aligned) */
+
+ tsect = LD_WORD(fs->win+BPB_TotSec16); /* Number of sectors on the volume */
+ if (!tsect) tsect = LD_DWORD(fs->win+BPB_TotSec32);
+
+ nrsv = LD_WORD(fs->win+BPB_RsvdSecCnt); /* Number of reserved sectors */
+ if (!nrsv) return FR_NO_FILESYSTEM; /* (BPB_RsvdSecCnt must not be 0) */
+
+ /* Determine the FAT sub type */
+ sysect = nrsv + fasize + fs->n_rootdir / (SS(fs) / SZ_DIR); /* RSV+FAT+FATFS_DIR */
+ if (tsect < sysect) return FR_NO_FILESYSTEM; /* (Invalid volume size) */
+ nclst = (tsect - sysect) / fs->csize; /* Number of clusters */
+ if (!nclst) return FR_NO_FILESYSTEM; /* (Invalid volume size) */
+ fmt = FS_FAT12;
+ if (nclst >= MIN_FAT16) fmt = FS_FAT16;
+ if (nclst >= MIN_FAT32) fmt = FS_FAT32;
+
+ /* Boundaries and Limits */
+ fs->n_fatent = nclst + 2; /* Number of FAT entries */
+ fs->database = bsect + sysect; /* Data start sector */
+ fs->fatbase = bsect + nrsv; /* FAT start sector */
+ if (fmt == FS_FAT32) {
+ if (fs->n_rootdir) return FR_NO_FILESYSTEM; /* (BPB_RootEntCnt must be 0) */
+ fs->dirbase = LD_DWORD(fs->win+BPB_RootClus); /* Root directory start cluster */
+ szbfat = fs->n_fatent * 4; /* (Required FAT size) */
+ } else {
+ if (!fs->n_rootdir) return FR_NO_FILESYSTEM; /* (BPB_RootEntCnt must not be 0) */
+ fs->dirbase = fs->fatbase + fasize; /* Root directory start sector */
+ szbfat = (fmt == FS_FAT16) ? /* (Required FAT size) */
+ fs->n_fatent * 2 : fs->n_fatent * 3 / 2 + (fs->n_fatent & 1);
+ }
+ if (fs->fsize < (szbfat + (SS(fs) - 1)) / SS(fs)) /* (BPB_FATSz must not be less than required) */
+ return FR_NO_FILESYSTEM;
+
+#if !_FS_READONLY
+ /* Initialize cluster allocation information */
+ fs->free_clust = 0xFFFFFFFF;
+ fs->last_clust = 0;
+
+ /* Get fsinfo if available */
+ if (fmt == FS_FAT32) {
+ fs->fsi_flag = 0;
+ fs->fsi_sector = bsect + LD_WORD(fs->win+BPB_FSInfo);
+ if (disk_read(fs->drv, fs->win, fs->fsi_sector, 1) == RES_OK &&
+ LD_WORD(fs->win+BS_55AA) == 0xAA55 &&
+ LD_DWORD(fs->win+FSI_LeadSig) == 0x41615252 &&
+ LD_DWORD(fs->win+FSI_StrucSig) == 0x61417272) {
+ fs->last_clust = LD_DWORD(fs->win+FSI_Nxt_Free);
+ fs->free_clust = LD_DWORD(fs->win+FSI_Free_Count);
+ }
+ }
+#endif
+ fs->fs_type = fmt; /* FAT sub-type */
+ fs->id = ++Fsid; /* File system mount ID */
+ fs->winsect = 0; /* Invalidate sector cache */
+ fs->wflag = 0;
+#if _FS_RPATH
+ fs->cdir = 0; /* Current directory (root dir) */
+#endif
+#if _FS_SHARE /* Clear file lock semaphores */
+ clear_lock(fs);
+#endif
+
+ return FR_OK;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Check if the file/dir object is valid or not */
+/*-----------------------------------------------------------------------*/
+
+static
+FRESULT validate ( /* FR_OK(0): The object is valid, !=0: Invalid */
+ FATFS *fs, /* Pointer to the file system object */
+ WORD id /* Member id of the target object to be checked */
+)
+{
+ if (!fs || !fs->fs_type || fs->id != id)
+ return FR_INVALID_OBJECT;
+
+ ENTER_FF(fs); /* Lock file system */
+
+ if (disk_status(fs->drv) & STA_NOINIT)
+ return FR_NOT_READY;
+
+ return FR_OK;
+}
+
+
+
+
+/*--------------------------------------------------------------------------
+
+ Public Functions
+
+--------------------------------------------------------------------------*/
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Mount/Unmount a Logical Drive */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_mount (
+ BYTE vol, /* Logical drive number to be mounted/unmounted */
+ FATFS *fs /* Pointer to new file system object (NULL for unmount)*/
+)
+{
+ FATFS *rfs;
+
+
+ if (vol >= _VOLUMES) /* Check if the drive number is valid */
+ return FR_INVALID_DRIVE;
+ rfs = FatFs[vol]; /* Get current fs object */
+
+ if (rfs) {
+#if _FS_SHARE
+ clear_lock(rfs);
+#endif
+#if _FS_REENTRANT /* Discard sync object of the current volume */
+ if (!ff_del_syncobj(rfs->sobj)) return FR_INT_ERR;
+#endif
+ rfs->fs_type = 0; /* Clear old fs object */
+ }
+
+ if (fs) {
+ fs->fs_type = 0; /* Clear new fs object */
+#if _FS_REENTRANT /* Create sync object for the new volume */
+ if (!ff_cre_syncobj(vol, &fs->sobj)) return FR_INT_ERR;
+#endif
+ }
+ FatFs[vol] = fs; /* Register new fs object */
+
+ return FR_OK;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Open or Create a File */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_open (
+ FIL *fp, /* Pointer to the blank file object */
+ const TCHAR *path, /* Pointer to the file name */
+ BYTE mode /* Access mode and file open mode flags */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ BYTE *dir;
+ DEF_NAMEBUF;
+
+
+ fp->fs = 0; /* Clear file object */
+
+#if !_FS_READONLY
+ mode &= FA_READ | FA_WRITE | FA_CREATE_ALWAYS | FA_OPEN_ALWAYS | FA_CREATE_NEW;
+ res = chk_mounted(&path, &dj.fs, (BYTE)(mode & ~FA_READ));
+#else
+ mode &= FA_READ;
+ res = chk_mounted(&path, &dj.fs, 0);
+#endif
+ INIT_BUF(dj);
+ if (res == FR_OK)
+ res = follow_path(&dj, path); /* Follow the file path */
+ dir = dj.dir;
+
+#if !_FS_READONLY /* R/W configuration */
+ if (res == FR_OK) {
+ if (!dir) /* Current dir itself */
+ res = FR_INVALID_NAME;
+#if _FS_SHARE
+ else
+ res = chk_lock(&dj, (mode & ~FA_READ) ? 1 : 0);
+#endif
+ }
+ /* Create or Open a file */
+ if (mode & (FA_CREATE_ALWAYS | FA_OPEN_ALWAYS | FA_CREATE_NEW)) {
+ DWORD dw, cl;
+
+ if (res != FR_OK) { /* No file, create new */
+ if (res == FR_NO_FILE) /* There is no file to open, create a new entry */
+#if _FS_SHARE
+ res = enq_lock() ? dir_register(&dj) : FR_TOO_MANY_OPEN_FILES;
+#else
+ res = dir_register(&dj);
+#endif
+ mode |= FA_CREATE_ALWAYS; /* File is created */
+ dir = dj.dir; /* New entry */
+ }
+ else { /* Any object is already existing */
+ if (dir[DIR_Attr] & (AM_RDO | AM_DIR)) { /* Cannot overwrite it (R/O or FATFS_DIR) */
+ res = FR_DENIED;
+ } else {
+ if (mode & FA_CREATE_NEW) /* Cannot create as new file */
+ res = FR_EXIST;
+ }
+ }
+ if (res == FR_OK && (mode & FA_CREATE_ALWAYS)) { /* Truncate it if overwrite mode */
+ dw = get_fattime(); /* Created time */
+ ST_DWORD(dir+DIR_CrtTime, dw);
+ dir[DIR_Attr] = 0; /* Reset attribute */
+ ST_DWORD(dir+DIR_FileSize, 0); /* size = 0 */
+ cl = LD_CLUST(dir); /* Get start cluster */
+ ST_CLUST(dir, 0); /* cluster = 0 */
+ dj.fs->wflag = 1;
+ if (cl) { /* Remove the cluster chain if exist */
+ dw = dj.fs->winsect;
+ res = remove_chain(dj.fs, cl);
+ if (res == FR_OK) {
+ dj.fs->last_clust = cl - 1; /* Reuse the cluster hole */
+ res = move_window(dj.fs, dw);
+ }
+ }
+ }
+ }
+ else { /* Open an existing file */
+ if (res == FR_OK) { /* Follow succeeded */
+ if (dir[DIR_Attr] & AM_DIR) { /* It is a directory */
+ res = FR_NO_FILE;
+ } else {
+ if ((mode & FA_WRITE) && (dir[DIR_Attr] & AM_RDO)) /* R/O violation */
+ res = FR_DENIED;
+ }
+ }
+ }
+ if (res == FR_OK) {
+ if (mode & FA_CREATE_ALWAYS) /* Set file change flag if created or overwritten */
+ mode |= FA__WRITTEN;
+ fp->dir_sect = dj.fs->winsect; /* Pointer to the directory entry */
+ fp->dir_ptr = dir;
+#if _FS_SHARE
+ fp->lockid = inc_lock(&dj, (mode & ~FA_READ) ? 1 : 0);
+ if (!fp->lockid) res = FR_INT_ERR;
+#endif
+ }
+
+#else /* R/O configuration */
+ if (res == FR_OK) { /* Follow succeeded */
+ if (!dir) { /* Current dir itself */
+ res = FR_INVALID_NAME;
+ } else {
+ if (dir[DIR_Attr] & AM_DIR) /* It is a directory */
+ res = FR_NO_FILE;
+ }
+ }
+#endif
+ FREE_BUF();
+
+ if (res == FR_OK) {
+ fp->flag = mode; /* File access mode */
+ fp->sclust = LD_CLUST(dir); /* File start cluster */
+ fp->fsize = LD_DWORD(dir+DIR_FileSize); /* File size */
+ fp->fptr = 0; /* File pointer */
+ fp->dsect = 0;
+#if _USE_FASTSEEK
+ fp->cltbl = 0; /* Normal seek mode */
+#endif
+ fp->fs = dj.fs; fp->id = dj.fs->id; /* Validate file object */
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Read File */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_read (
+ FIL *fp, /* Pointer to the file object */
+ void *buff, /* Pointer to data buffer */
+ UINT btr, /* Number of bytes to read */
+ UINT *br /* Pointer to number of bytes read */
+)
+{
+ FRESULT res;
+ DWORD clst, sect, remain;
+ UINT rcnt, cc;
+ BYTE csect, *rbuff = (BYTE*)buff;
+
+
+ *br = 0; /* Initialize byte counter */
+
+ res = validate(fp->fs, fp->id); /* Check validity */
+ if (res != FR_OK) LEAVE_FF(fp->fs, res);
+ if (fp->flag & FA__ERROR) /* Aborted file? */
+ LEAVE_FF(fp->fs, FR_INT_ERR);
+ if (!(fp->flag & FA_READ)) /* Check access mode */
+ LEAVE_FF(fp->fs, FR_DENIED);
+ remain = fp->fsize - fp->fptr;
+ if (btr > remain) btr = (UINT)remain; /* Truncate btr by remaining bytes */
+
+ for ( ; btr; /* Repeat until all data read */
+ rbuff += rcnt, fp->fptr += rcnt, *br += rcnt, btr -= rcnt) {
+ if ((fp->fptr % SS(fp->fs)) == 0) { /* On the sector boundary? */
+ csect = (BYTE)(fp->fptr / SS(fp->fs) & (fp->fs->csize - 1)); /* Sector offset in the cluster */
+ if (!csect) { /* On the cluster boundary? */
+ if (fp->fptr == 0) { /* On the top of the file? */
+ clst = fp->sclust; /* Follow from the origin */
+ } else { /* Middle or end of the file */
+#if _USE_FASTSEEK
+ if (fp->cltbl)
+ clst = clmt_clust(fp, fp->fptr); /* Get cluster# from the CLMT */
+ else
+#endif
+ clst = get_fat(fp->fs, fp->clust); /* Follow cluster chain on the FAT */
+ }
+ if (clst < 2) ABORT(fp->fs, FR_INT_ERR);
+ if (clst == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ fp->clust = clst; /* Update current cluster */
+ }
+ sect = clust2sect(fp->fs, fp->clust); /* Get current sector */
+ if (!sect) ABORT(fp->fs, FR_INT_ERR);
+ sect += csect;
+ cc = btr / SS(fp->fs); /* When remaining bytes >= sector size, */
+ if (cc) { /* Read maximum contiguous sectors directly */
+ if (csect + cc > fp->fs->csize) /* Clip at cluster boundary */
+ cc = fp->fs->csize - csect;
+ if (disk_read(fp->fs->drv, rbuff, sect, (BYTE)cc) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+#if !_FS_READONLY && _FS_MINIMIZE <= 2 /* Replace one of the read sectors with cached data if it contains a dirty sector */
+#if _FS_TINY
+ if (fp->fs->wflag && fp->fs->winsect - sect < cc)
+ mem_cpy(rbuff + ((fp->fs->winsect - sect) * SS(fp->fs)), fp->fs->win, SS(fp->fs));
+#else
+ if ((fp->flag & FA__DIRTY) && fp->dsect - sect < cc)
+ mem_cpy(rbuff + ((fp->dsect - sect) * SS(fp->fs)), fp->buf, SS(fp->fs));
+#endif
+#endif
+ rcnt = SS(fp->fs) * cc; /* Number of bytes transferred */
+ continue;
+ }
+#if !_FS_TINY
+ if (fp->dsect != sect) { /* Load data sector if not in cache */
+#if !_FS_READONLY
+ if (fp->flag & FA__DIRTY) { /* Write-back dirty sector cache */
+ if (disk_write(fp->fs->drv, fp->buf, fp->dsect, 1) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ if (disk_read(fp->fs->drv, fp->buf, sect, 1) != RES_OK) /* Fill sector cache */
+ ABORT(fp->fs, FR_DISK_ERR);
+ }
+#endif
+ fp->dsect = sect;
+ }
+ rcnt = SS(fp->fs) - (fp->fptr % SS(fp->fs)); /* Get partial sector data from sector buffer */
+ if (rcnt > btr) rcnt = btr;
+#if _FS_TINY
+ if (move_window(fp->fs, fp->dsect)) /* Move sector window */
+ ABORT(fp->fs, FR_DISK_ERR);
+ mem_cpy(rbuff, &fp->fs->win[fp->fptr % SS(fp->fs)], rcnt); /* Pick partial sector */
+#else
+ mem_cpy(rbuff, &fp->buf[fp->fptr % SS(fp->fs)], rcnt); /* Pick partial sector */
+#endif
+ }
+
+ LEAVE_FF(fp->fs, FR_OK);
+}
+
+
+
+
+#if !_FS_READONLY
+/*-----------------------------------------------------------------------*/
+/* Write File */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_write (
+ FIL *fp, /* Pointer to the file object */
+ const void *buff, /* Pointer to the data to be written */
+ UINT btw, /* Number of bytes to write */
+ UINT *bw /* Pointer to number of bytes written */
+)
+{
+ FRESULT res;
+ DWORD clst, sect;
+ UINT wcnt, cc;
+ const BYTE *wbuff = (const BYTE*)buff;
+ BYTE csect;
+
+
+ *bw = 0; /* Initialize byte counter */
+
+ res = validate(fp->fs, fp->id); /* Check validity */
+ if (res != FR_OK) LEAVE_FF(fp->fs, res);
+ if (fp->flag & FA__ERROR) /* Aborted file? */
+ LEAVE_FF(fp->fs, FR_INT_ERR);
+ if (!(fp->flag & FA_WRITE)) /* Check access mode */
+ LEAVE_FF(fp->fs, FR_DENIED);
+ if ((DWORD)(fp->fsize + btw) < fp->fsize) btw = 0; /* File size cannot reach 4GB */
+
+ for ( ; btw; /* Repeat until all data written */
+ wbuff += wcnt, fp->fptr += wcnt, *bw += wcnt, btw -= wcnt) {
+ if ((fp->fptr % SS(fp->fs)) == 0) { /* On the sector boundary? */
+ csect = (BYTE)(fp->fptr / SS(fp->fs) & (fp->fs->csize - 1)); /* Sector offset in the cluster */
+ if (!csect) { /* On the cluster boundary? */
+ if (fp->fptr == 0) { /* On the top of the file? */
+ clst = fp->sclust; /* Follow from the origin */
+ if (clst == 0) /* When no cluster is allocated, */
+ fp->sclust = clst = create_chain(fp->fs, 0); /* Create a new cluster chain */
+ } else { /* Middle or end of the file */
+#if _USE_FASTSEEK
+ if (fp->cltbl)
+ clst = clmt_clust(fp, fp->fptr); /* Get cluster# from the CLMT */
+ else
+#endif
+ clst = create_chain(fp->fs, fp->clust); /* Follow or stretch cluster chain on the FAT */
+ }
+ if (clst == 0) break; /* Could not allocate a new cluster (disk full) */
+ if (clst == 1) ABORT(fp->fs, FR_INT_ERR);
+ if (clst == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ fp->clust = clst; /* Update current cluster */
+ }
+#if _FS_TINY
+ if (fp->fs->winsect == fp->dsect && move_window(fp->fs, 0)) /* Write-back sector cache */
+ ABORT(fp->fs, FR_DISK_ERR);
+#else
+ if (fp->flag & FA__DIRTY) { /* Write-back sector cache */
+ if (disk_write(fp->fs->drv, fp->buf, fp->dsect, 1) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ sect = clust2sect(fp->fs, fp->clust); /* Get current sector */
+ if (!sect) ABORT(fp->fs, FR_INT_ERR);
+ sect += csect;
+ cc = btw / SS(fp->fs); /* When remaining bytes >= sector size, */
+ if (cc) { /* Write maximum contiguous sectors directly */
+ if (csect + cc > fp->fs->csize) /* Clip at cluster boundary */
+ cc = fp->fs->csize - csect;
+ if (disk_write(fp->fs->drv, wbuff, sect, (BYTE)cc) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+#if _FS_TINY
+ if (fp->fs->winsect - sect < cc) { /* Refill sector cache if it gets invalidated by the direct write */
+ mem_cpy(fp->fs->win, wbuff + ((fp->fs->winsect - sect) * SS(fp->fs)), SS(fp->fs));
+ fp->fs->wflag = 0;
+ }
+#else
+ if (fp->dsect - sect < cc) { /* Refill sector cache if it gets invalidated by the direct write */
+ mem_cpy(fp->buf, wbuff + ((fp->dsect - sect) * SS(fp->fs)), SS(fp->fs));
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ wcnt = SS(fp->fs) * cc; /* Number of bytes transferred */
+ continue;
+ }
+#if _FS_TINY
+ if (fp->fptr >= fp->fsize) { /* Avoid silly cache filling at growing edge */
+ if (move_window(fp->fs, 0)) ABORT(fp->fs, FR_DISK_ERR);
+ fp->fs->winsect = sect;
+ }
+#else
+ if (fp->dsect != sect) { /* Fill sector cache with file data */
+ if (fp->fptr < fp->fsize &&
+ disk_read(fp->fs->drv, fp->buf, sect, 1) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+ }
+#endif
+ fp->dsect = sect;
+ }
+ wcnt = SS(fp->fs) - (fp->fptr % SS(fp->fs));/* Put partial sector into file I/O buffer */
+ if (wcnt > btw) wcnt = btw;
+#if _FS_TINY
+ if (move_window(fp->fs, fp->dsect)) /* Move sector window */
+ ABORT(fp->fs, FR_DISK_ERR);
+ mem_cpy(&fp->fs->win[fp->fptr % SS(fp->fs)], wbuff, wcnt); /* Fit partial sector */
+ fp->fs->wflag = 1;
+#else
+ mem_cpy(&fp->buf[fp->fptr % SS(fp->fs)], wbuff, wcnt); /* Fit partial sector */
+ fp->flag |= FA__DIRTY;
+#endif
+ }
+
+ if (fp->fptr > fp->fsize) fp->fsize = fp->fptr; /* Update file size if needed */
+ fp->flag |= FA__WRITTEN; /* Set file change flag */
+
+ LEAVE_FF(fp->fs, FR_OK);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Synchronize the File Object */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_sync (
+ FIL *fp /* Pointer to the file object */
+)
+{
+ FRESULT res;
+ DWORD tim;
+ BYTE *dir;
+
+
+ res = validate(fp->fs, fp->id); /* Check validity of the object */
+ if (res == FR_OK) {
+ if (fp->flag & FA__WRITTEN) { /* Has the file been written? */
+#if !_FS_TINY /* Write-back dirty buffer */
+ if (fp->flag & FA__DIRTY) {
+ if (disk_write(fp->fs->drv, fp->buf, fp->dsect, 1) != RES_OK)
+ LEAVE_FF(fp->fs, FR_DISK_ERR);
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ /* Update the directory entry */
+ res = move_window(fp->fs, fp->dir_sect);
+ if (res == FR_OK) {
+ dir = fp->dir_ptr;
+ dir[DIR_Attr] |= AM_ARC; /* Set archive bit */
+ ST_DWORD(dir+DIR_FileSize, fp->fsize); /* Update file size */
+ ST_CLUST(dir, fp->sclust); /* Update start cluster */
+ tim = get_fattime(); /* Update updated time */
+ ST_DWORD(dir+DIR_WrtTime, tim);
+ fp->flag &= ~FA__WRITTEN;
+ fp->fs->wflag = 1;
+ res = sync(fp->fs);
+ }
+ }
+ }
+
+ LEAVE_FF(fp->fs, res);
+}
+
+#endif /* !_FS_READONLY */
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Close File */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_close (
+ FIL *fp /* Pointer to the file object to be closed */
+)
+{
+ FRESULT res;
+
+#if _FS_READONLY
+ FATFS *fs = fp->fs;
+ res = validate(fs, fp->id);
+ if (res == FR_OK) fp->fs = 0; /* Discard file object */
+ LEAVE_FF(fs, res);
+
+#else
+ res = f_sync(fp); /* Flush cached data */
+#if _FS_SHARE
+ if (res == FR_OK) { /* Decrement open counter */
+#if _FS_REENTRANT
+ res = validate(fp->fs, fp->id);
+ if (res == FR_OK) {
+ res = dec_lock(fp->lockid);
+ unlock_fs(fp->fs, FR_OK);
+ }
+#else
+ res = dec_lock(fp->lockid);
+#endif
+ }
+#endif
+ if (res == FR_OK) fp->fs = 0; /* Discard file object */
+ return res;
+#endif
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Current Drive/Directory Handlings */
+/*-----------------------------------------------------------------------*/
+
+#if _FS_RPATH >= 1
+
+FRESULT f_chdrive (
+ BYTE drv /* Drive number */
+)
+{
+ if (drv >= _VOLUMES) return FR_INVALID_DRIVE;
+
+ CurrVol = drv;
+
+ return FR_OK;
+}
+
+
+
+FRESULT f_chdir (
+ const TCHAR *path /* Pointer to the directory path */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 0);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the path */
+ FREE_BUF();
+ if (res == FR_OK) { /* Follow completed */
+ if (!dj.dir) {
+ dj.fs->cdir = dj.sclust; /* Start directory itself */
+ } else {
+ if (dj.dir[DIR_Attr] & AM_DIR) /* Reached to the directory */
+ dj.fs->cdir = LD_CLUST(dj.dir);
+ else
+ res = FR_NO_PATH; /* Reached but a file */
+ }
+ }
+ if (res == FR_NO_FILE) res = FR_NO_PATH;
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+#if _FS_RPATH >= 2
+FRESULT f_getcwd (
+ TCHAR *path, /* Pointer to the directory path */
+ UINT sz_path /* Size of path */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ UINT i, n;
+ DWORD ccl;
+ TCHAR *tp;
+ FILINFO fno;
+ DEF_NAMEBUF;
+
+
+ *path = 0;
+ res = chk_mounted((const TCHAR**)&path, &dj.fs, 0); /* Get current volume */
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ i = sz_path; /* Bottom of buffer (dir stack base) */
+ dj.sclust = dj.fs->cdir; /* Start to follow upper dir from current dir */
+ while ((ccl = dj.sclust) != 0) { /* Repeat while current dir is a sub-dir */
+ res = dir_sdi(&dj, 1); /* Get parent dir */
+ if (res != FR_OK) break;
+ res = dir_read(&dj);
+ if (res != FR_OK) break;
+ dj.sclust = LD_CLUST(dj.dir); /* Goto parent dir */
+ res = dir_sdi(&dj, 0);
+ if (res != FR_OK) break;
+ do { /* Find the entry links to the child dir */
+ res = dir_read(&dj);
+ if (res != FR_OK) break;
+ if (ccl == LD_CLUST(dj.dir)) break; /* Found the entry */
+ res = dir_next(&dj, 0);
+ } while (res == FR_OK);
+ if (res == FR_NO_FILE) res = FR_INT_ERR;/* It cannot be 'not found'. */
+ if (res != FR_OK) break;
+#if _USE_LFN
+ fno.lfname = path;
+ fno.lfsize = i;
+#endif
+ get_fileinfo(&dj, &fno); /* Get the dir name and push it to the buffer */
+ tp = fno.fname;
+ if (_USE_LFN && *path) tp = path;
+ for (n = 0; tp[n]; n++) ;
+ if (i < n + 3) {
+ res = FR_NOT_ENOUGH_CORE; break;
+ }
+ while (n) path[--i] = tp[--n];
+ path[--i] = '/';
+ }
+ tp = path;
+ if (res == FR_OK) {
+ *tp++ = '0' + CurrVol; /* Put drive number */
+ *tp++ = ':';
+ if (i == sz_path) { /* Root-dir */
+ *tp++ = '/';
+ } else { /* Sub-dir */
+ do /* Add stacked path str */
+ *tp++ = path[i++];
+ while (i < sz_path);
+ }
+ }
+ *tp = 0;
+ FREE_BUF();
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+#endif /* _FS_RPATH >= 2 */
+#endif /* _FS_RPATH >= 1 */
+
+
+
+#if _FS_MINIMIZE <= 2
+/*-----------------------------------------------------------------------*/
+/* Seek File R/W Pointer */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_lseek (
+ FIL *fp, /* Pointer to the file object */
+ DWORD ofs /* File pointer from top of file */
+)
+{
+ FRESULT res;
+
+
+ res = validate(fp->fs, fp->id); /* Check validity of the object */
+ if (res != FR_OK) LEAVE_FF(fp->fs, res);
+ if (fp->flag & FA__ERROR) /* Check abort flag */
+ LEAVE_FF(fp->fs, FR_INT_ERR);
+
+#if _USE_FASTSEEK
+ if (fp->cltbl) { /* Fast seek */
+ DWORD cl, pcl, ncl, tcl, dsc, tlen, ulen, *tbl;
+
+ if (ofs == CREATE_LINKMAP) { /* Create CLMT */
+ tbl = fp->cltbl;
+ tlen = *tbl++; ulen = 2; /* Given table size and required table size */
+ cl = fp->sclust; /* Top of the chain */
+ if (cl) {
+ do {
+ /* Get a fragment */
+ tcl = cl; ncl = 0; ulen += 2; /* Top, length and used items */
+ do {
+ pcl = cl; ncl++;
+ cl = get_fat(fp->fs, cl);
+ if (cl <= 1) ABORT(fp->fs, FR_INT_ERR);
+ if (cl == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ } while (cl == pcl + 1);
+ if (ulen <= tlen) { /* Store the length and top of the fragment */
+ *tbl++ = ncl; *tbl++ = tcl;
+ }
+ } while (cl < fp->fs->n_fatent); /* Repeat until end of chain */
+ }
+ *fp->cltbl = ulen; /* Number of items used */
+ if (ulen <= tlen)
+ *tbl = 0; /* Terminate table */
+ else
+ res = FR_NOT_ENOUGH_CORE; /* Given table size is smaller than required */
+
+ } else { /* Fast seek */
+ if (ofs > fp->fsize) /* Clip offset at the file size */
+ ofs = fp->fsize;
+ fp->fptr = ofs; /* Set file pointer */
+ if (ofs) {
+ fp->clust = clmt_clust(fp, ofs - 1);
+ dsc = clust2sect(fp->fs, fp->clust);
+ if (!dsc) ABORT(fp->fs, FR_INT_ERR);
+ dsc += (ofs - 1) / SS(fp->fs) & (fp->fs->csize - 1);
+ if (fp->fptr % SS(fp->fs) && dsc != fp->dsect) { /* Refill sector cache if needed */
+#if !_FS_TINY
+#if !_FS_READONLY
+ if (fp->flag & FA__DIRTY) { /* Write-back dirty sector cache */
+ if (disk_write(fp->fs->drv, fp->buf, fp->dsect, 1) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ if (disk_read(fp->fs->drv, fp->buf, dsc, 1) != RES_OK) /* Load current sector */
+ ABORT(fp->fs, FR_DISK_ERR);
+#endif
+ fp->dsect = dsc;
+ }
+ }
+ }
+ } else
+#endif
+
+ /* Normal Seek */
+ {
+ DWORD clst, bcs, nsect, ifptr;
+
+ if (ofs > fp->fsize /* In read-only mode, clip offset with the file size */
+#if !_FS_READONLY
+ && !(fp->flag & FA_WRITE)
+#endif
+ ) ofs = fp->fsize;
+
+ ifptr = fp->fptr;
+ fp->fptr = nsect = 0;
+ if (ofs) {
+ bcs = (DWORD)fp->fs->csize * SS(fp->fs); /* Cluster size (byte) */
+ if (ifptr > 0 &&
+ (ofs - 1) / bcs >= (ifptr - 1) / bcs) { /* When seek to same or following cluster, */
+ fp->fptr = (ifptr - 1) & ~(bcs - 1); /* start from the current cluster */
+ ofs -= fp->fptr;
+ clst = fp->clust;
+ } else { /* When seek to back cluster, */
+ clst = fp->sclust; /* start from the first cluster */
+#if !_FS_READONLY
+ if (clst == 0) { /* If no cluster chain, create a new chain */
+ clst = create_chain(fp->fs, 0);
+ if (clst == 1) ABORT(fp->fs, FR_INT_ERR);
+ if (clst == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ fp->sclust = clst;
+ }
+#endif
+ fp->clust = clst;
+ }
+ if (clst != 0) {
+ while (ofs > bcs) { /* Cluster following loop */
+#if !_FS_READONLY
+ if (fp->flag & FA_WRITE) { /* Check if in write mode or not */
+ clst = create_chain(fp->fs, clst); /* Force stretch if in write mode */
+ if (clst == 0) { /* When disk gets full, clip file size */
+ ofs = bcs; break;
+ }
+ } else
+#endif
+ clst = get_fat(fp->fs, clst); /* Follow cluster chain if not in write mode */
+ if (clst == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ if (clst <= 1 || clst >= fp->fs->n_fatent) ABORT(fp->fs, FR_INT_ERR);
+ fp->clust = clst;
+ fp->fptr += bcs;
+ ofs -= bcs;
+ }
+ fp->fptr += ofs;
+ if (ofs % SS(fp->fs)) {
+ nsect = clust2sect(fp->fs, clst); /* Current sector */
+ if (!nsect) ABORT(fp->fs, FR_INT_ERR);
+ nsect += ofs / SS(fp->fs);
+ }
+ }
+ }
+ if (fp->fptr % SS(fp->fs) && nsect != fp->dsect) { /* Fill sector cache if needed */
+#if !_FS_TINY
+#if !_FS_READONLY
+ if (fp->flag & FA__DIRTY) { /* Write-back dirty sector cache */
+ if (disk_write(fp->fs->drv, fp->buf, fp->dsect, 1) != RES_OK)
+ ABORT(fp->fs, FR_DISK_ERR);
+ fp->flag &= ~FA__DIRTY;
+ }
+#endif
+ if (disk_read(fp->fs->drv, fp->buf, nsect, 1) != RES_OK) /* Fill sector cache */
+ ABORT(fp->fs, FR_DISK_ERR);
+#endif
+ fp->dsect = nsect;
+ }
+#if !_FS_READONLY
+ if (fp->fptr > fp->fsize) { /* Set file change flag if the file size is extended */
+ fp->fsize = fp->fptr;
+ fp->flag |= FA__WRITTEN;
+ }
+#endif
+ }
+
+ LEAVE_FF(fp->fs, res);
+}
+
+
+
+#if _FS_MINIMIZE <= 1
+/*-----------------------------------------------------------------------*/
+/* Create a Directroy Object */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_opendir (
+ FATFS_DIR *dj, /* Pointer to directory object to create */
+ const TCHAR *path /* Pointer to the directory path */
+)
+{
+ FRESULT res;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj->fs, 0);
+ if (res == FR_OK) {
+ INIT_BUF(*dj);
+ res = follow_path(dj, path); /* Follow the path to the directory */
+ FREE_BUF();
+ if (res == FR_OK) { /* Follow completed */
+ if (dj->dir) { /* It is not the root dir */
+ if (dj->dir[DIR_Attr] & AM_DIR) { /* The object is a directory */
+ dj->sclust = LD_CLUST(dj->dir);
+ } else { /* The object is not a directory */
+ res = FR_NO_PATH;
+ }
+ }
+ if (res == FR_OK) {
+ dj->id = dj->fs->id;
+ res = dir_sdi(dj, 0); /* Rewind dir */
+ }
+ }
+ if (res == FR_NO_FILE) res = FR_NO_PATH;
+ }
+
+ LEAVE_FF(dj->fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Read Directory Entry in Sequense */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_readdir (
+ FATFS_DIR *dj, /* Pointer to the open directory object */
+ FILINFO *fno /* Pointer to file information to return */
+)
+{
+ FRESULT res;
+ DEF_NAMEBUF;
+
+
+ res = validate(dj->fs, dj->id); /* Check validity of the object */
+ if (res == FR_OK) {
+ if (!fno) {
+ res = dir_sdi(dj, 0); /* Rewind the directory object */
+ } else {
+ INIT_BUF(*dj);
+ res = dir_read(dj); /* Read an directory item */
+ if (res == FR_NO_FILE) { /* Reached end of dir */
+ dj->sect = 0;
+ res = FR_OK;
+ }
+ if (res == FR_OK) { /* A valid entry is found */
+ get_fileinfo(dj, fno); /* Get the object information */
+ res = dir_next(dj, 0); /* Increment index for next */
+ if (res == FR_NO_FILE) {
+ dj->sect = 0;
+ res = FR_OK;
+ }
+ }
+ FREE_BUF();
+ }
+ }
+
+ LEAVE_FF(dj->fs, res);
+}
+
+
+
+#if _FS_MINIMIZE == 0
+/*-----------------------------------------------------------------------*/
+/* Get File Status */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_stat (
+ const TCHAR *path, /* Pointer to the file path */
+ FILINFO *fno /* Pointer to file information to return */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 0);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the file path */
+ if (res == FR_OK) { /* Follow completed */
+ if (dj.dir) /* Found an object */
+ get_fileinfo(&dj, fno);
+ else /* It is root dir */
+ res = FR_INVALID_NAME;
+ }
+ FREE_BUF();
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+#if !_FS_READONLY
+/*-----------------------------------------------------------------------*/
+/* Get Number of Free Clusters */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_getfree (
+ const TCHAR *path, /* Pointer to the logical drive number (root dir) */
+ DWORD *nclst, /* Pointer to the variable to return number of free clusters */
+ FATFS **fatfs /* Pointer to pointer to corresponding file system object to return */
+)
+{
+ FRESULT res;
+ DWORD n, clst, sect, stat;
+ UINT i;
+ BYTE fat, *p;
+
+
+ /* Get drive number */
+ res = chk_mounted(&path, fatfs, 0);
+ if (res == FR_OK) {
+ /* If free_clust is valid, return it without full cluster scan */
+ if ((*fatfs)->free_clust <= (*fatfs)->n_fatent - 2) {
+ *nclst = (*fatfs)->free_clust;
+ } else {
+ /* Get number of free clusters */
+ fat = (*fatfs)->fs_type;
+ n = 0;
+ if (fat == FS_FAT12) {
+ clst = 2;
+ do {
+ stat = get_fat(*fatfs, clst);
+ if (stat == 0xFFFFFFFF) { res = FR_DISK_ERR; break; }
+ if (stat == 1) { res = FR_INT_ERR; break; }
+ if (stat == 0) n++;
+ } while (++clst < (*fatfs)->n_fatent);
+ } else {
+ clst = (*fatfs)->n_fatent;
+ sect = (*fatfs)->fatbase;
+ i = 0; p = 0;
+ do {
+ if (!i) {
+ res = move_window(*fatfs, sect++);
+ if (res != FR_OK) break;
+ p = (*fatfs)->win;
+ i = SS(*fatfs);
+ }
+ if (fat == FS_FAT16) {
+ if (LD_WORD(p) == 0) n++;
+ p += 2; i -= 2;
+ } else {
+ if ((LD_DWORD(p) & 0x0FFFFFFF) == 0) n++;
+ p += 4; i -= 4;
+ }
+ } while (--clst);
+ }
+ (*fatfs)->free_clust = n;
+ if (fat == FS_FAT32) (*fatfs)->fsi_flag = 1;
+ *nclst = n;
+ }
+ }
+ LEAVE_FF(*fatfs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Truncate File */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_truncate (
+ FIL *fp /* Pointer to the file object */
+)
+{
+ FRESULT res;
+ DWORD ncl;
+
+
+ res = validate(fp->fs, fp->id); /* Check validity of the object */
+ if (res == FR_OK) {
+ if (fp->flag & FA__ERROR) { /* Check abort flag */
+ res = FR_INT_ERR;
+ } else {
+ if (!(fp->flag & FA_WRITE)) /* Check access mode */
+ res = FR_DENIED;
+ }
+ }
+ if (res == FR_OK) {
+ if (fp->fsize > fp->fptr) {
+ fp->fsize = fp->fptr; /* Set file size to current R/W point */
+ fp->flag |= FA__WRITTEN;
+ if (fp->fptr == 0) { /* When set file size to zero, remove entire cluster chain */
+ res = remove_chain(fp->fs, fp->sclust);
+ fp->sclust = 0;
+ } else { /* When truncate a part of the file, remove remaining clusters */
+ ncl = get_fat(fp->fs, fp->clust);
+ res = FR_OK;
+ if (ncl == 0xFFFFFFFF) res = FR_DISK_ERR;
+ if (ncl == 1) res = FR_INT_ERR;
+ if (res == FR_OK && ncl < fp->fs->n_fatent) {
+ res = put_fat(fp->fs, fp->clust, 0x0FFFFFFF);
+ if (res == FR_OK) res = remove_chain(fp->fs, ncl);
+ }
+ }
+ }
+ if (res != FR_OK) fp->flag |= FA__ERROR;
+ }
+
+ LEAVE_FF(fp->fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Delete a File or Directory */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_unlink (
+ const TCHAR *path /* Pointer to the file or directory path */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj, sdj;
+ BYTE *dir;
+ DWORD dclst;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 1);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the file path */
+ if (_FS_RPATH && res == FR_OK && (dj.fn[NS] & NS_DOT))
+ res = FR_INVALID_NAME; /* Cannot remove dot entry */
+#if _FS_SHARE
+ if (res == FR_OK) res = chk_lock(&dj, 2); /* Cannot remove open file */
+#endif
+ if (res == FR_OK) { /* The object is accessible */
+ dir = dj.dir;
+ if (!dir) {
+ res = FR_INVALID_NAME; /* Cannot remove the start directory */
+ } else {
+ if (dir[DIR_Attr] & AM_RDO)
+ res = FR_DENIED; /* Cannot remove R/O object */
+ }
+ dclst = LD_CLUST(dir);
+ if (res == FR_OK && (dir[DIR_Attr] & AM_DIR)) { /* Is it a sub-dir? */
+ if (dclst < 2) {
+ res = FR_INT_ERR;
+ } else {
+ mem_cpy(&sdj, &dj, sizeof(FATFS_DIR)); /* Check if the sub-dir is empty or not */
+ sdj.sclust = dclst;
+ res = dir_sdi(&sdj, 2); /* Exclude dot entries */
+ if (res == FR_OK) {
+ res = dir_read(&sdj);
+ if (res == FR_OK /* Not empty dir */
+#if _FS_RPATH
+ || dclst == sdj.fs->cdir /* Current dir */
+#endif
+ ) res = FR_DENIED;
+ if (res == FR_NO_FILE) res = FR_OK; /* Empty */
+ }
+ }
+ }
+ if (res == FR_OK) {
+ res = dir_remove(&dj); /* Remove the directory entry */
+ if (res == FR_OK) {
+ if (dclst) /* Remove the cluster chain if exist */
+ res = remove_chain(dj.fs, dclst);
+ if (res == FR_OK) res = sync(dj.fs);
+ }
+ }
+ }
+ FREE_BUF();
+ }
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Create a Directory */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_mkdir (
+ const TCHAR *path /* Pointer to the directory path */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ BYTE *dir, n;
+ DWORD dsc, dcl, pcl, tim = get_fattime();
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 1);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the file path */
+ if (res == FR_OK) res = FR_EXIST; /* Any object with same name is already existing */
+ if (_FS_RPATH && res == FR_NO_FILE && (dj.fn[NS] & NS_DOT))
+ res = FR_INVALID_NAME;
+ if (res == FR_NO_FILE) { /* Can create a new directory */
+ dcl = create_chain(dj.fs, 0); /* Allocate a cluster for the new directory table */
+ res = FR_OK;
+ if (dcl == 0) res = FR_DENIED; /* No space to allocate a new cluster */
+ if (dcl == 1) res = FR_INT_ERR;
+ if (dcl == 0xFFFFFFFF) res = FR_DISK_ERR;
+ if (res == FR_OK) /* Flush FAT */
+ res = move_window(dj.fs, 0);
+ if (res == FR_OK) { /* Initialize the new directory table */
+ dsc = clust2sect(dj.fs, dcl);
+ dir = dj.fs->win;
+ mem_set(dir, 0, SS(dj.fs));
+ mem_set(dir+DIR_Name, ' ', 8+3); /* Create "." entry */
+ dir[DIR_Name] = '.';
+ dir[DIR_Attr] = AM_DIR;
+ ST_DWORD(dir+DIR_WrtTime, tim);
+ ST_CLUST(dir, dcl);
+ mem_cpy(dir+SZ_DIR, dir, SZ_DIR); /* Create ".." entry */
+ dir[33] = '.'; pcl = dj.sclust;
+ if (dj.fs->fs_type == FS_FAT32 && pcl == dj.fs->dirbase)
+ pcl = 0;
+ ST_CLUST(dir+SZ_DIR, pcl);
+ for (n = dj.fs->csize; n; n--) { /* Write dot entries and clear following sectors */
+ dj.fs->winsect = dsc++;
+ dj.fs->wflag = 1;
+ res = move_window(dj.fs, 0);
+ if (res != FR_OK) break;
+ mem_set(dir, 0, SS(dj.fs));
+ }
+ }
+ if (res == FR_OK) res = dir_register(&dj); /* Register the object to the directoy */
+ if (res != FR_OK) {
+ remove_chain(dj.fs, dcl); /* Could not register, remove cluster chain */
+ } else {
+ dir = dj.dir;
+ dir[DIR_Attr] = AM_DIR; /* Attribute */
+ ST_DWORD(dir+DIR_WrtTime, tim); /* Created time */
+ ST_CLUST(dir, dcl); /* Table start cluster */
+ dj.fs->wflag = 1;
+ res = sync(dj.fs);
+ }
+ }
+ FREE_BUF();
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Change Attribute */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_chmod (
+ const TCHAR *path, /* Pointer to the file path */
+ BYTE value, /* Attribute bits */
+ BYTE mask /* Attribute mask to change */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ BYTE *dir;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 1);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the file path */
+ FREE_BUF();
+ if (_FS_RPATH && res == FR_OK && (dj.fn[NS] & NS_DOT))
+ res = FR_INVALID_NAME;
+ if (res == FR_OK) {
+ dir = dj.dir;
+ if (!dir) { /* Is it a root directory? */
+ res = FR_INVALID_NAME;
+ } else { /* File or sub directory */
+ mask &= AM_RDO|AM_HID|AM_SYS|AM_ARC; /* Valid attribute mask */
+ dir[DIR_Attr] = (value & mask) | (dir[DIR_Attr] & (BYTE)~mask); /* Apply attribute change */
+ dj.fs->wflag = 1;
+ res = sync(dj.fs);
+ }
+ }
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Change Timestamp */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_utime (
+ const TCHAR *path, /* Pointer to the file/directory name */
+ const FILINFO *fno /* Pointer to the time stamp to be set */
+)
+{
+ FRESULT res;
+ FATFS_DIR dj;
+ BYTE *dir;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path, &dj.fs, 1);
+ if (res == FR_OK) {
+ INIT_BUF(dj);
+ res = follow_path(&dj, path); /* Follow the file path */
+ FREE_BUF();
+ if (_FS_RPATH && res == FR_OK && (dj.fn[NS] & NS_DOT))
+ res = FR_INVALID_NAME;
+ if (res == FR_OK) {
+ dir = dj.dir;
+ if (!dir) { /* Root directory */
+ res = FR_INVALID_NAME;
+ } else { /* File or sub-directory */
+ ST_WORD(dir+DIR_WrtTime, fno->ftime);
+ ST_WORD(dir+DIR_WrtDate, fno->fdate);
+ dj.fs->wflag = 1;
+ res = sync(dj.fs);
+ }
+ }
+ }
+
+ LEAVE_FF(dj.fs, res);
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Rename File/Directory */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_rename (
+ const TCHAR *path_old, /* Pointer to the old name */
+ const TCHAR *path_new /* Pointer to the new name */
+)
+{
+ FRESULT res;
+ FATFS_DIR djo, djn;
+ BYTE buf[21], *dir;
+ DWORD dw;
+ DEF_NAMEBUF;
+
+
+ res = chk_mounted(&path_old, &djo.fs, 1);
+ if (res == FR_OK) {
+ djn.fs = djo.fs;
+ INIT_BUF(djo);
+ res = follow_path(&djo, path_old); /* Check old object */
+ if (_FS_RPATH && res == FR_OK && (djo.fn[NS] & NS_DOT))
+ res = FR_INVALID_NAME;
+#if _FS_SHARE
+ if (res == FR_OK) res = chk_lock(&djo, 2);
+#endif
+ if (res == FR_OK) { /* Old object is found */
+ if (!djo.dir) { /* Is root dir? */
+ res = FR_NO_FILE;
+ } else {
+ mem_cpy(buf, djo.dir+DIR_Attr, 21); /* Save the object information except for name */
+ mem_cpy(&djn, &djo, sizeof(FATFS_DIR)); /* Check new object */
+ res = follow_path(&djn, path_new);
+ if (res == FR_OK) res = FR_EXIST; /* The new object name is already existing */
+ if (res == FR_NO_FILE) { /* Is it a valid path and no name collision? */
+/* Start critical section that any interruption or error can cause cross-link */
+ res = dir_register(&djn); /* Register the new entry */
+ if (res == FR_OK) {
+ dir = djn.dir; /* Copy object information except for name */
+ mem_cpy(dir+13, buf+2, 19);
+ dir[DIR_Attr] = buf[0] | AM_ARC;
+ djo.fs->wflag = 1;
+ if (djo.sclust != djn.sclust && (dir[DIR_Attr] & AM_DIR)) { /* Update .. entry in the directory if needed */
+ dw = clust2sect(djn.fs, LD_CLUST(dir));
+ if (!dw) {
+ res = FR_INT_ERR;
+ } else {
+ res = move_window(djn.fs, dw);
+ dir = djn.fs->win+SZ_DIR; /* .. entry */
+ if (res == FR_OK && dir[1] == '.') {
+ dw = (djn.fs->fs_type == FS_FAT32 && djn.sclust == djn.fs->dirbase) ? 0 : djn.sclust;
+ ST_CLUST(dir, dw);
+ djn.fs->wflag = 1;
+ }
+ }
+ }
+ if (res == FR_OK) {
+ res = dir_remove(&djo); /* Remove old entry */
+ if (res == FR_OK)
+ res = sync(djo.fs);
+ }
+ }
+/* End critical section */
+ }
+ }
+ }
+ FREE_BUF();
+ }
+ LEAVE_FF(djo.fs, res);
+}
+
+#endif /* !_FS_READONLY */
+#endif /* _FS_MINIMIZE == 0 */
+#endif /* _FS_MINIMIZE <= 1 */
+#endif /* _FS_MINIMIZE <= 2 */
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Forward data to the stream directly (available on only tiny cfg) */
+/*-----------------------------------------------------------------------*/
+#if _USE_FORWARD && _FS_TINY
+
+FRESULT f_forward (
+ FIL *fp, /* Pointer to the file object */
+ UINT (*func)(const BYTE*,UINT), /* Pointer to the streaming function */
+ UINT btr, /* Number of bytes to forward */
+ UINT *bf /* Pointer to number of bytes forwarded */
+)
+{
+ FRESULT res;
+ DWORD remain, clst, sect;
+ UINT rcnt;
+ BYTE csect;
+
+
+ *bf = 0; /* Initialize byte counter */
+
+ res = validate(fp->fs, fp->id); /* Check validity of the object */
+ if (res != FR_OK) LEAVE_FF(fp->fs, res);
+ if (fp->flag & FA__ERROR) /* Check error flag */
+ LEAVE_FF(fp->fs, FR_INT_ERR);
+ if (!(fp->flag & FA_READ)) /* Check access mode */
+ LEAVE_FF(fp->fs, FR_DENIED);
+
+ remain = fp->fsize - fp->fptr;
+ if (btr > remain) btr = (UINT)remain; /* Truncate btr by remaining bytes */
+
+ for ( ; btr && (*func)(0, 0); /* Repeat until all data transferred or stream becomes busy */
+ fp->fptr += rcnt, *bf += rcnt, btr -= rcnt) {
+ csect = (BYTE)(fp->fptr / SS(fp->fs) & (fp->fs->csize - 1)); /* Sector offset in the cluster */
+ if ((fp->fptr % SS(fp->fs)) == 0) { /* On the sector boundary? */
+ if (!csect) { /* On the cluster boundary? */
+ clst = (fp->fptr == 0) ? /* On the top of the file? */
+ fp->sclust : get_fat(fp->fs, fp->clust);
+ if (clst <= 1) ABORT(fp->fs, FR_INT_ERR);
+ if (clst == 0xFFFFFFFF) ABORT(fp->fs, FR_DISK_ERR);
+ fp->clust = clst; /* Update current cluster */
+ }
+ }
+ sect = clust2sect(fp->fs, fp->clust); /* Get current data sector */
+ if (!sect) ABORT(fp->fs, FR_INT_ERR);
+ sect += csect;
+ if (move_window(fp->fs, sect)) /* Move sector window */
+ ABORT(fp->fs, FR_DISK_ERR);
+ fp->dsect = sect;
+ rcnt = SS(fp->fs) - (WORD)(fp->fptr % SS(fp->fs)); /* Forward data from sector window */
+ if (rcnt > btr) rcnt = btr;
+ rcnt = (*func)(&fp->fs->win[(WORD)fp->fptr % SS(fp->fs)], rcnt);
+ if (!rcnt) ABORT(fp->fs, FR_INT_ERR);
+ }
+
+ LEAVE_FF(fp->fs, FR_OK);
+}
+#endif /* _USE_FORWARD */
+
+
+
+#if _USE_MKFS && !_FS_READONLY
+/*-----------------------------------------------------------------------*/
+/* Create File System on the Drive */
+/*-----------------------------------------------------------------------*/
+#define N_ROOTDIR 512 /* Number of root dir entries for FAT12/16 */
+#define N_FATS 1 /* Number of FAT copies (1 or 2) */
+
+
+FRESULT f_mkfs (
+ BYTE drv, /* Logical drive number */
+ BYTE sfd, /* Partitioning rule 0:FDISK, 1:SFD */
+ UINT au /* Allocation unit size [bytes] */
+)
+{
+ static const WORD vst[] = { 1024, 512, 256, 128, 64, 32, 16, 8, 4, 2, 0};
+ static const WORD cst[] = {32768, 16384, 8192, 4096, 2048, 16384, 8192, 4096, 2048, 1024, 512};
+ BYTE fmt, md, sys, *tbl, pdrv, part;
+ DWORD n_clst, vs, n, wsect;
+ UINT i;
+ DWORD b_vol, b_fat, b_dir, b_data; /* LBA */
+ DWORD n_vol, n_rsv, n_fat, n_dir; /* Size */
+ FATFS *fs;
+ DSTATUS stat;
+
+
+ /* Check mounted drive and clear work area */
+ if (drv >= _VOLUMES) return FR_INVALID_DRIVE;
+ if (sfd > 1) return FR_INVALID_PARAMETER;
+ if (au & (au - 1)) return FR_INVALID_PARAMETER;
+ fs = FatFs[drv];
+ if (!fs) return FR_NOT_ENABLED;
+ fs->fs_type = 0;
+ pdrv = LD2PD(drv); /* Physical drive */
+ part = LD2PT(drv); /* Partition (0:auto detect, 1-4:get from partition table)*/
+
+ /* Get disk statics */
+ stat = disk_initialize(pdrv);
+ if (stat & STA_NOINIT) return FR_NOT_READY;
+ if (stat & STA_PROTECT) return FR_WRITE_PROTECTED;
+#if _MAX_SS != 512 /* Get disk sector size */
+ if (disk_ioctl(pdrv, GET_SECTOR_SIZE, &SS(fs)) != RES_OK || SS(fs) > _MAX_SS)
+ return FR_DISK_ERR;
+#endif
+ if (_MULTI_PARTITION && part) {
+ /* Get partition information from partition table in the MBR */
+ if (disk_read(pdrv, fs->win, 0, 1) != RES_OK) return FR_DISK_ERR;
+ if (LD_WORD(fs->win+BS_55AA) != 0xAA55) return FR_MKFS_ABORTED;
+ tbl = &fs->win[MBR_Table + (part - 1) * SZ_PTE];
+ if (!tbl[4]) return FR_MKFS_ABORTED; /* No partition? */
+ b_vol = LD_DWORD(tbl+8); /* Volume start sector */
+ n_vol = LD_DWORD(tbl+12); /* Volume size */
+ } else {
+ /* Create a partition in this function */
+ if (disk_ioctl(pdrv, GET_SECTOR_COUNT, &n_vol) != RES_OK || n_vol < 128)
+ return FR_DISK_ERR;
+ b_vol = (sfd) ? 0 : 63; /* Volume start sector */
+ n_vol -= b_vol; /* Volume size */
+ }
+
+ if (!au) { /* AU auto selection */
+ vs = n_vol / (2000 / (SS(fs) / 512));
+ for (i = 0; vs < vst[i]; i++) ;
+ au = cst[i];
+ }
+ au /= SS(fs); /* Number of sectors per cluster */
+ if (au == 0) au = 1;
+ if (au > 128) au = 128;
+
+ /* Pre-compute number of clusters and FAT syb-type */
+ n_clst = n_vol / au;
+ fmt = FS_FAT12;
+ if (n_clst >= MIN_FAT16) fmt = FS_FAT16;
+ if (n_clst >= MIN_FAT32) fmt = FS_FAT32;
+
+ /* Determine offset and size of FAT structure */
+ if (fmt == FS_FAT32) {
+ n_fat = ((n_clst * 4) + 8 + SS(fs) - 1) / SS(fs);
+ n_rsv = 32;
+ n_dir = 0;
+ } else {
+ n_fat = (fmt == FS_FAT12) ? (n_clst * 3 + 1) / 2 + 3 : (n_clst * 2) + 4;
+ n_fat = (n_fat + SS(fs) - 1) / SS(fs);
+ n_rsv = 1;
+ n_dir = (DWORD)N_ROOTDIR * SZ_DIR / SS(fs);
+ }
+ b_fat = b_vol + n_rsv; /* FAT area start sector */
+ b_dir = b_fat + n_fat * N_FATS; /* Directory area start sector */
+ b_data = b_dir + n_dir; /* Data area start sector */
+ if (n_vol < b_data + au - b_vol) return FR_MKFS_ABORTED; /* Too small volume */
+
+ /* Align data start sector to erase block boundary (for flash memory media) */
+ if (disk_ioctl(pdrv, GET_BLOCK_SIZE, &n) != RES_OK || !n || n > 32768) n = 1;
+ n = (b_data + n - 1) & ~(n - 1); /* Next nearest erase block from current data start */
+ n = (n - b_data) / N_FATS;
+ if (fmt == FS_FAT32) { /* FAT32: Move FAT offset */
+ n_rsv += n;
+ b_fat += n;
+ } else { /* FAT12/16: Expand FAT size */
+ n_fat += n;
+ }
+
+ /* Determine number of clusters and final check of validity of the FAT sub-type */
+ n_clst = (n_vol - n_rsv - n_fat * N_FATS - n_dir) / au;
+ if ( (fmt == FS_FAT16 && n_clst < MIN_FAT16)
+ || (fmt == FS_FAT32 && n_clst < MIN_FAT32))
+ return FR_MKFS_ABORTED;
+
+ switch (fmt) { /* Determine system ID for partition table */
+ case FS_FAT12: sys = 0x01; break;
+ case FS_FAT16: sys = (n_vol < 0x10000) ? 0x04 : 0x06; break;
+ default: sys = 0x0C;
+ }
+
+ if (_MULTI_PARTITION && part) {
+ /* Update system ID in the partition table */
+ tbl = &fs->win[MBR_Table + (part - 1) * SZ_PTE];
+ tbl[4] = sys;
+ if (disk_write(pdrv, fs->win, 0, 1) != RES_OK) return FR_DISK_ERR;
+ md = 0xF8;
+ } else {
+ if (sfd) { /* No patition table (SFD) */
+ md = 0xF0;
+ } else { /* Create partition table (FDISK) */
+ mem_set(fs->win, 0, SS(fs));
+ tbl = fs->win+MBR_Table; /* Create partiton table for single partition in the drive */
+ tbl[1] = 1; /* Partition start head */
+ tbl[2] = 1; /* Partition start sector */
+ tbl[3] = 0; /* Partition start cylinder */
+ tbl[4] = sys; /* System type */
+ tbl[5] = 254; /* Partition end head */
+ n = (b_vol + n_vol) / 63 / 255;
+ tbl[6] = (BYTE)((n >> 2) | 63); /* Partiiton end sector */
+ tbl[7] = (BYTE)n; /* End cylinder */
+ ST_DWORD(tbl+8, 63); /* Partition start in LBA */
+ ST_DWORD(tbl+12, n_vol); /* Partition size in LBA */
+ ST_WORD(fs->win+BS_55AA, 0xAA55); /* MBR signature */
+ if (disk_write(pdrv, fs->win, 0, 1) != RES_OK) /* Write it to the MBR sector */
+ return FR_DISK_ERR;
+ md = 0xF8;
+ }
+ }
+
+ /* Create BPB in the VBR */
+ tbl = fs->win; /* Clear sector */
+ mem_set(tbl, 0, SS(fs));
+ mem_cpy(tbl, "\xEB\xFE\x90" "MSDOS5.0", 11);/* Boot jump code, OEM name */
+ i = SS(fs); /* Sector size */
+ ST_WORD(tbl+BPB_BytsPerSec, i);
+ tbl[BPB_SecPerClus] = (BYTE)au; /* Sectors per cluster */
+ ST_WORD(tbl+BPB_RsvdSecCnt, n_rsv); /* Reserved sectors */
+ tbl[BPB_NumFATs] = N_FATS; /* Number of FATs */
+ i = (fmt == FS_FAT32) ? 0 : N_ROOTDIR; /* Number of rootdir entries */
+ ST_WORD(tbl+BPB_RootEntCnt, i);
+ if (n_vol < 0x10000) { /* Number of total sectors */
+ ST_WORD(tbl+BPB_TotSec16, n_vol);
+ } else {
+ ST_DWORD(tbl+BPB_TotSec32, n_vol);
+ }
+ tbl[BPB_Media] = md; /* Media descriptor */
+ ST_WORD(tbl+BPB_SecPerTrk, 63); /* Number of sectors per track */
+ ST_WORD(tbl+BPB_NumHeads, 255); /* Number of heads */
+ ST_DWORD(tbl+BPB_HiddSec, b_vol); /* Hidden sectors */
+ n = get_fattime(); /* Use current time as VSN */
+ if (fmt == FS_FAT32) {
+ ST_DWORD(tbl+BS_VolID32, n); /* VSN */
+ ST_DWORD(tbl+BPB_FATSz32, n_fat); /* Number of sectors per FAT */
+ ST_DWORD(tbl+BPB_RootClus, 2); /* Root directory start cluster (2) */
+ ST_WORD(tbl+BPB_FSInfo, 1); /* FSInfo record offset (VBR+1) */
+ ST_WORD(tbl+BPB_BkBootSec, 6); /* Backup boot record offset (VBR+6) */
+ tbl[BS_DrvNum32] = 0x80; /* Drive number */
+ tbl[BS_BootSig32] = 0x29; /* Extended boot signature */
+ mem_cpy(tbl+BS_VolLab32, "NO NAME " "FAT32 ", 19); /* Volume label, FAT signature */
+ } else {
+ ST_DWORD(tbl+BS_VolID, n); /* VSN */
+ ST_WORD(tbl+BPB_FATSz16, n_fat); /* Number of sectors per FAT */
+ tbl[BS_DrvNum] = 0x80; /* Drive number */
+ tbl[BS_BootSig] = 0x29; /* Extended boot signature */
+ mem_cpy(tbl+BS_VolLab, "NO NAME " "FAT ", 19); /* Volume label, FAT signature */
+ }
+ ST_WORD(tbl+BS_55AA, 0xAA55); /* Signature (Offset is fixed here regardless of sector size) */
+ if (disk_write(pdrv, tbl, b_vol, 1) != RES_OK) /* Write it to the VBR sector */
+ return FR_DISK_ERR;
+ if (fmt == FS_FAT32) /* Write backup VBR if needed (VBR+6) */
+ disk_write(pdrv, tbl, b_vol + 6, 1);
+
+ /* Initialize FAT area */
+ wsect = b_fat;
+ for (i = 0; i < N_FATS; i++) { /* Initialize each FAT copy */
+ mem_set(tbl, 0, SS(fs)); /* 1st sector of the FAT */
+ n = md; /* Media descriptor byte */
+ if (fmt != FS_FAT32) {
+ n |= (fmt == FS_FAT12) ? 0x00FFFF00 : 0xFFFFFF00;
+ ST_DWORD(tbl+0, n); /* Reserve cluster #0-1 (FAT12/16) */
+ } else {
+ n |= 0xFFFFFF00;
+ ST_DWORD(tbl+0, n); /* Reserve cluster #0-1 (FAT32) */
+ ST_DWORD(tbl+4, 0xFFFFFFFF);
+ ST_DWORD(tbl+8, 0x0FFFFFFF); /* Reserve cluster #2 for root dir */
+ }
+ if (disk_write(pdrv, tbl, wsect++, 1) != RES_OK)
+ return FR_DISK_ERR;
+ mem_set(tbl, 0, SS(fs)); /* Fill following FAT entries with zero */
+ for (n = 1; n < n_fat; n++) { /* This loop may take a time on FAT32 volume due to many single sector writes */
+ if (disk_write(pdrv, tbl, wsect++, 1) != RES_OK)
+ return FR_DISK_ERR;
+ }
+ }
+
+ /* Initialize root directory */
+ i = (fmt == FS_FAT32) ? au : n_dir;
+ do {
+ if (disk_write(pdrv, tbl, wsect++, 1) != RES_OK)
+ return FR_DISK_ERR;
+ } while (--i);
+
+#if _USE_ERASE /* Erase data area if needed */
+ {
+ DWORD eb[2];
+
+ eb[0] = wsect; eb[1] = wsect + (n_clst - ((fmt == FS_FAT32) ? 1 : 0)) * au - 1;
+ disk_ioctl(pdrv, CTRL_ERASE_SECTOR, eb);
+ }
+#endif
+
+ /* Create FSInfo if needed */
+ if (fmt == FS_FAT32) {
+ ST_DWORD(tbl+FSI_LeadSig, 0x41615252);
+ ST_DWORD(tbl+FSI_StrucSig, 0x61417272);
+ ST_DWORD(tbl+FSI_Free_Count, n_clst - 1); /* Number of free clusters */
+ ST_DWORD(tbl+FSI_Nxt_Free, 2); /* Last allocated cluster# */
+ ST_WORD(tbl+BS_55AA, 0xAA55);
+ disk_write(pdrv, tbl, b_vol + 1, 1); /* Write original (VBR+1) */
+ disk_write(pdrv, tbl, b_vol + 7, 1); /* Write backup (VBR+7) */
+ }
+
+ return (disk_ioctl(pdrv, CTRL_SYNC, 0) == RES_OK) ? FR_OK : FR_DISK_ERR;
+}
+
+
+#if _MULTI_PARTITION == 2
+/*-----------------------------------------------------------------------*/
+/* Divide Physical Drive */
+/*-----------------------------------------------------------------------*/
+
+FRESULT f_fdisk (
+ BYTE pdrv, /* Physical drive number */
+ const DWORD szt[], /* Pointer to the size table for each partitions */
+ void* work /* Pointer to the working buffer */
+)
+{
+ UINT i, n, sz_cyl, tot_cyl, b_cyl, e_cyl, p_cyl;
+ BYTE s_hd, e_hd, *p, *buf = (BYTE*)work;
+ DSTATUS stat;
+ DWORD sz_disk, sz_part, s_part;
+
+
+ stat = disk_initialize(pdrv);
+ if (stat & STA_NOINIT) return FR_NOT_READY;
+ if (stat & STA_PROTECT) return FR_WRITE_PROTECTED;
+ if (disk_ioctl(pdrv, GET_SECTOR_COUNT, &sz_disk)) return FR_DISK_ERR;
+
+ /* Determine CHS in the table regardless of the drive geometry */
+ for (n = 16; n < 256 && sz_disk / n / 63 > 1024; n *= 2) ;
+ if (n == 256) n--;
+ e_hd = n - 1;
+ sz_cyl = 63 * n;
+ tot_cyl = sz_disk / sz_cyl;
+
+ /* Create partition table */
+ mem_set(buf, 0, _MAX_SS);
+ p = buf + MBR_Table; b_cyl = 0;
+ for (i = 0; i < 4; i++, p += SZ_PTE) {
+ p_cyl = (szt[i] <= 100) ? (DWORD)tot_cyl * szt[i] / 100 : szt[i] / sz_cyl;
+ if (!p_cyl) continue;
+ s_part = (DWORD)sz_cyl * b_cyl;
+ sz_part = (DWORD)sz_cyl * p_cyl;
+ if (i == 0) { /* Exclude first track of cylinder 0 */
+ s_hd = 1;
+ s_part += 63; sz_part -= 63;
+ } else {
+ s_hd = 0;
+ }
+ e_cyl = b_cyl + p_cyl - 1;
+ if (e_cyl >= tot_cyl) return FR_INVALID_PARAMETER;
+
+ /* Set partition table */
+ p[1] = s_hd; /* Start head */
+ p[2] = (BYTE)((b_cyl >> 2) + 1); /* Start sector */
+ p[3] = (BYTE)b_cyl; /* Start cylinder */
+ p[4] = 0x06; /* System type (temporary setting) */
+ p[5] = e_hd; /* End head */
+ p[6] = (BYTE)((e_cyl >> 2) + 63); /* End sector */
+ p[7] = (BYTE)e_cyl; /* End cylinder */
+ ST_DWORD(p + 8, s_part); /* Start sector in LBA */
+ ST_DWORD(p + 12, sz_part); /* Partition size */
+
+ /* Next partition */
+ b_cyl += p_cyl;
+ }
+ ST_WORD(p, 0xAA55);
+
+ /* Write it to the MBR */
+ return (disk_write(pdrv, buf, 0, 1) || disk_ioctl(pdrv, CTRL_SYNC, 0)) ? FR_DISK_ERR : FR_OK;
+}
+
+
+#endif /* _MULTI_PARTITION == 2 */
+#endif /* _USE_MKFS && !_FS_READONLY */
+
+
+
+
+#if _USE_STRFUNC
+/*-----------------------------------------------------------------------*/
+/* Get a string from the file */
+/*-----------------------------------------------------------------------*/
+TCHAR* f_gets (
+ TCHAR* buff, /* Pointer to the string buffer to read */
+ int len, /* Size of string buffer (characters) */
+ FIL* fil /* Pointer to the file object */
+)
+{
+ int n = 0;
+ TCHAR c, *p = buff;
+ BYTE s[2];
+ UINT rc;
+
+
+ while (n < len - 1) { /* Read bytes until buffer gets filled */
+ f_read(fil, s, 1, &rc);
+ if (rc != 1) break; /* Break on EOF or error */
+ c = s[0];
+#if _LFN_UNICODE /* Read a character in UTF-8 encoding */
+ if (c >= 0x80) {
+ if (c < 0xC0) continue; /* Skip stray trailer */
+ if (c < 0xE0) { /* Two-byte sequense */
+ f_read(fil, s, 1, &rc);
+ if (rc != 1) break;
+ c = ((c & 0x1F) << 6) | (s[0] & 0x3F);
+ if (c < 0x80) c = '?';
+ } else {
+ if (c < 0xF0) { /* Three-byte sequense */
+ f_read(fil, s, 2, &rc);
+ if (rc != 2) break;
+ c = (c << 12) | ((s[0] & 0x3F) << 6) | (s[1] & 0x3F);
+ if (c < 0x800) c = '?';
+ } else { /* Reject four-byte sequense */
+ c = '?';
+ }
+ }
+ }
+#endif
+#if _USE_STRFUNC >= 2
+ if (c == '\r') continue; /* Strip '\r' */
+#endif
+ *p++ = c;
+ n++;
+ if (c == '\n') break; /* Break on EOL */
+ }
+ *p = 0;
+ return n ? buff : 0; /* When no data read (eof or error), return with error. */
+}
+
+
+
+#if !_FS_READONLY
+#include <stdarg.h>
+/*-----------------------------------------------------------------------*/
+/* Put a character to the file */
+/*-----------------------------------------------------------------------*/
+int f_putc (
+ TCHAR c, /* A character to be output */
+ FIL* fil /* Pointer to the file object */
+)
+{
+ UINT bw, btw;
+ BYTE s[3];
+
+
+#if _USE_STRFUNC >= 2
+ if (c == '\n') f_putc ('\r', fil); /* LF -> CRLF conversion */
+#endif
+
+#if _LFN_UNICODE /* Write the character in UTF-8 encoding */
+ if (c < 0x80) { /* 7-bit */
+ s[0] = (BYTE)c;
+ btw = 1;
+ } else {
+ if (c < 0x800) { /* 11-bit */
+ s[0] = (BYTE)(0xC0 | (c >> 6));
+ s[1] = (BYTE)(0x80 | (c & 0x3F));
+ btw = 2;
+ } else { /* 16-bit */
+ s[0] = (BYTE)(0xE0 | (c >> 12));
+ s[1] = (BYTE)(0x80 | ((c >> 6) & 0x3F));
+ s[2] = (BYTE)(0x80 | (c & 0x3F));
+ btw = 3;
+ }
+ }
+#else /* Write the character without conversion */
+ s[0] = (BYTE)c;
+ btw = 1;
+#endif
+ f_write(fil, s, btw, &bw); /* Write the char to the file */
+ return (bw == btw) ? 1 : EOF; /* Return the result */
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Put a string to the file */
+/*-----------------------------------------------------------------------*/
+int f_puts (
+ const TCHAR* str, /* Pointer to the string to be output */
+ FIL* fil /* Pointer to the file object */
+)
+{
+ int n;
+
+
+ for (n = 0; *str; str++, n++) {
+ if (f_putc(*str, fil) == EOF) return EOF;
+ }
+ return n;
+}
+
+
+
+
+/*-----------------------------------------------------------------------*/
+/* Put a formatted string to the file */
+/*-----------------------------------------------------------------------*/
+int f_printf (
+ FIL* fil, /* Pointer to the file object */
+ const TCHAR* str, /* Pointer to the format string */
+ ... /* Optional arguments... */
+)
+{
+ va_list arp;
+ BYTE f, r;
+ UINT i, j, w;
+ ULONG v;
+ TCHAR c, d, s[16], *p;
+ int res, chc, cc;
+
+
+ va_start(arp, str);
+
+ for (cc = res = 0; cc != EOF; res += cc) {
+ c = *str++;
+ if (c == 0) break; /* End of string */
+ if (c != '%') { /* Non escape character */
+ cc = f_putc(c, fil);
+ if (cc != EOF) cc = 1;
+ continue;
+ }
+ w = f = 0;
+ c = *str++;
+ if (c == '0') { /* Flag: '0' padding */
+ f = 1; c = *str++;
+ } else {
+ if (c == '-') { /* Flag: left justified */
+ f = 2; c = *str++;
+ }
+ }
+ while (IsDigit(c)) { /* Precision */
+ w = w * 10 + c - '0';
+ c = *str++;
+ }
+ if (c == 'l' || c == 'L') { /* Prefix: Size is long int */
+ f |= 4; c = *str++;
+ }
+ if (!c) break;
+ d = c;
+ if (IsLower(d)) d -= 0x20;
+ switch (d) { /* Type is... */
+ case 'S' : /* String */
+ p = va_arg(arp, TCHAR*);
+ for (j = 0; p[j]; j++) ;
+ chc = 0;
+ if (!(f & 2)) {
+ while (j++ < w) chc += (cc = f_putc(' ', fil));
+ }
+ chc += (cc = f_puts(p, fil));
+ while (j++ < w) chc += (cc = f_putc(' ', fil));
+ if (cc != EOF) cc = chc;
+ continue;
+ case 'C' : /* Character */
+ cc = f_putc((TCHAR)va_arg(arp, int), fil); continue;
+ case 'B' : /* Binary */
+ r = 2; break;
+ case 'O' : /* Octal */
+ r = 8; break;
+ case 'D' : /* Signed decimal */
+ case 'U' : /* Unsigned decimal */
+ r = 10; break;
+ case 'X' : /* Hexdecimal */
+ r = 16; break;
+ default: /* Unknown type (passthrough) */
+ cc = f_putc(c, fil); continue;
+ }
+
+ /* Get an argument and put it in numeral */
+ v = (f & 4) ? (ULONG)va_arg(arp, long) : ((d == 'D') ? (ULONG)(long)va_arg(arp, int) : (ULONG)va_arg(arp, unsigned int));
+ if (d == 'D' && (v & 0x80000000)) {
+ v = 0 - v;
+ f |= 8;
+ }
+ i = 0;
+ do {
+ d = (TCHAR)(v % r); v /= r;
+ if (d > 9) d += (c == 'x') ? 0x27 : 0x07;
+ s[i++] = d + '0';
+ } while (v && i < sizeof(s) / sizeof(s[0]));
+ if (f & 8) s[i++] = '-';
+ j = i; d = (f & 1) ? '0' : ' ';
+ res = 0;
+ while (!(f & 2) && j++ < w) res += (cc = f_putc(d, fil));
+ do res += (cc = f_putc(s[--i], fil)); while(i);
+ while (j++ < w) res += (cc = f_putc(' ', fil));
+ if (cc != EOF) cc = res;
+ }
+
+ va_end(arp);
+ return (cc == EOF) ? cc : res;
+}
+
+#endif /* !_FS_READONLY */
+#endif /* _USE_STRFUNC */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/ff.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,337 @@
+/*---------------------------------------------------------------------------/
+/ FatFs - FAT file system module include file R0.09 (C)ChaN, 2011
+/----------------------------------------------------------------------------/
+/ FatFs module is a generic FAT file system module for small embedded systems.
+/ This is a free software that opened for education, research and commercial
+/ developments under license policy of following trems.
+/
+/ Copyright (C) 2011, ChaN, all right reserved.
+/
+/ * The FatFs module is a free software and there is NO WARRANTY.
+/ * No restriction on use. You can use, modify and redistribute it for
+/ personal, non-profit or commercial product UNDER YOUR RESPONSIBILITY.
+/ * Redistributions of source code must retain the above copyright notice.
+/
+/----------------------------------------------------------------------------*/
+
+#ifndef _FATFS
+#define _FATFS 6502 /* Revision ID */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include "integer.h" /* Basic integer types */
+#include "ffconf.h" /* FatFs configuration options */
+
+#if _FATFS != _FFCONF
+#error Wrong configuration file (ffconf.h).
+#endif
+
+
+
+/* Definitions of volume management */
+
+#if _MULTI_PARTITION /* Multiple partition configuration */
+typedef struct {
+ BYTE pd; /* Physical drive number */
+ BYTE pt; /* Partition: 0:Auto detect, 1-4:Forced partition) */
+} PARTITION;
+extern PARTITION VolToPart[]; /* Volume - Partition resolution table */
+#define LD2PD(vol) (VolToPart[vol].pd) /* Get physical drive number */
+#define LD2PT(vol) (VolToPart[vol].pt) /* Get partition index */
+
+#else /* Single partition configuration */
+#define LD2PD(vol) (vol) /* Each logical drive is bound to the same physical drive number */
+#define LD2PT(vol) 0 /* Always mounts the 1st partition or in SFD */
+
+#endif
+
+
+
+/* Type of path name strings on FatFs API */
+
+#if _LFN_UNICODE /* Unicode string */
+#if !_USE_LFN
+#error _LFN_UNICODE must be 0 in non-LFN cfg.
+#endif
+#ifndef _INC_TCHAR
+typedef WCHAR TCHAR;
+#define _T(x) L ## x
+#define _TEXT(x) L ## x
+#endif
+
+#else /* ANSI/OEM string */
+#ifndef _INC_TCHAR
+typedef char TCHAR;
+#define _T(x) x
+#define _TEXT(x) x
+#endif
+
+#endif
+
+
+
+/* File system object structure (FATFS) */
+
+typedef struct {
+ BYTE fs_type; /* FAT sub-type (0:Not mounted) */
+ BYTE drv; /* Physical drive number */
+ BYTE csize; /* Sectors per cluster (1,2,4...128) */
+ BYTE n_fats; /* Number of FAT copies (1,2) */
+ BYTE wflag; /* win[] dirty flag (1:must be written back) */
+ BYTE fsi_flag; /* fsinfo dirty flag (1:must be written back) */
+ WORD id; /* File system mount ID */
+ WORD n_rootdir; /* Number of root directory entries (FAT12/16) */
+#if _MAX_SS != 512
+ WORD ssize; /* Bytes per sector (512, 1024, 2048 or 4096) */
+#endif
+#if _FS_REENTRANT
+ _SYNC_t sobj; /* Identifier of sync object */
+#endif
+#if !_FS_READONLY
+ DWORD last_clust; /* Last allocated cluster */
+ DWORD free_clust; /* Number of free clusters */
+ DWORD fsi_sector; /* fsinfo sector (FAT32) */
+#endif
+#if _FS_RPATH
+ DWORD cdir; /* Current directory start cluster (0:root) */
+#endif
+ DWORD n_fatent; /* Number of FAT entries (= number of clusters + 2) */
+ DWORD fsize; /* Sectors per FAT */
+ DWORD fatbase; /* FAT start sector */
+ DWORD dirbase; /* Root directory start sector (FAT32:Cluster#) */
+ DWORD database; /* Data start sector */
+ DWORD winsect; /* Current sector appearing in the win[] */
+ BYTE win[_MAX_SS]; /* Disk access window for Directory, FAT (and Data on tiny cfg) */
+} FATFS;
+
+
+
+/* File object structure (FIL) */
+
+typedef struct {
+ FATFS* fs; /* Pointer to the owner file system object */
+ WORD id; /* Owner file system mount ID */
+ BYTE flag; /* File status flags */
+ BYTE pad1;
+ DWORD fptr; /* File read/write pointer (0 on file open) */
+ DWORD fsize; /* File size */
+ DWORD sclust; /* File start cluster (0 when fsize==0) */
+ DWORD clust; /* Current cluster */
+ DWORD dsect; /* Current data sector */
+#if !_FS_READONLY
+ DWORD dir_sect; /* Sector containing the directory entry */
+ BYTE* dir_ptr; /* Ponter to the directory entry in the window */
+#endif
+#if _USE_FASTSEEK
+ DWORD* cltbl; /* Pointer to the cluster link map table (null on file open) */
+#endif
+#if _FS_SHARE
+ UINT lockid; /* File lock ID (index of file semaphore table) */
+#endif
+#if !_FS_TINY
+ BYTE buf[_MAX_SS]; /* File data read/write buffer */
+#endif
+} FIL;
+
+
+
+/* Directory object structure (FATFS_DIR) */
+
+typedef struct {
+ FATFS* fs; /* Pointer to the owner file system object */
+ WORD id; /* Owner file system mount ID */
+ WORD index; /* Current read/write index number */
+ DWORD sclust; /* Table start cluster (0:Root dir) */
+ DWORD clust; /* Current cluster */
+ DWORD sect; /* Current sector */
+ BYTE* dir; /* Pointer to the current SFN entry in the win[] */
+ BYTE* fn; /* Pointer to the SFN (in/out) {file[8],ext[3],status[1]} */
+#if _USE_LFN
+ WCHAR* lfn; /* Pointer to the LFN working buffer */
+ WORD lfn_idx; /* Last matched LFN index number (0xFFFF:No LFN) */
+#endif
+} FATFS_DIR;
+
+
+
+/* File status structure (FILINFO) */
+
+typedef struct {
+ DWORD fsize; /* File size */
+ WORD fdate; /* Last modified date */
+ WORD ftime; /* Last modified time */
+ BYTE fattrib; /* Attribute */
+ TCHAR fname[13]; /* Short file name (8.3 format) */
+#if _USE_LFN
+ TCHAR* lfname; /* Pointer to the LFN buffer */
+ UINT lfsize; /* Size of LFN buffer in TCHAR */
+#endif
+} FILINFO;
+
+
+
+/* File function return code (FRESULT) */
+
+typedef enum {
+ FR_OK = 0, /* (0) Succeeded */
+ FR_DISK_ERR, /* (1) A hard error occured in the low level disk I/O layer */
+ FR_INT_ERR, /* (2) Assertion failed */
+ FR_NOT_READY, /* (3) The physical drive cannot work */
+ FR_NO_FILE, /* (4) Could not find the file */
+ FR_NO_PATH, /* (5) Could not find the path */
+ FR_INVALID_NAME, /* (6) The path name format is invalid */
+ FR_DENIED, /* (7) Acces denied due to prohibited access or directory full */
+ FR_EXIST, /* (8) Acces denied due to prohibited access */
+ FR_INVALID_OBJECT, /* (9) The file/directory object is invalid */
+ FR_WRITE_PROTECTED, /* (10) The physical drive is write protected */
+ FR_INVALID_DRIVE, /* (11) The logical drive number is invalid */
+ FR_NOT_ENABLED, /* (12) The volume has no work area */
+ FR_NO_FILESYSTEM, /* (13) There is no valid FAT volume */
+ FR_MKFS_ABORTED, /* (14) The f_mkfs() aborted due to any parameter error */
+ FR_TIMEOUT, /* (15) Could not get a grant to access the volume within defined period */
+ FR_LOCKED, /* (16) The operation is rejected according to the file shareing policy */
+ FR_NOT_ENOUGH_CORE, /* (17) LFN working buffer could not be allocated */
+ FR_TOO_MANY_OPEN_FILES, /* (18) Number of open files > _FS_SHARE */
+ FR_INVALID_PARAMETER /* (19) Given parameter is invalid */
+} FRESULT;
+
+
+
+/*--------------------------------------------------------------*/
+/* FatFs module application interface */
+
+FRESULT f_mount (BYTE, FATFS*); /* Mount/Unmount a logical drive */
+FRESULT f_open (FIL*, const TCHAR*, BYTE); /* Open or create a file */
+FRESULT f_read (FIL*, void*, UINT, UINT*); /* Read data from a file */
+FRESULT f_lseek (FIL*, DWORD); /* Move file pointer of a file object */
+FRESULT f_close (FIL*); /* Close an open file object */
+FRESULT f_opendir (FATFS_DIR*, const TCHAR*); /* Open an existing directory */
+FRESULT f_readdir (FATFS_DIR*, FILINFO*); /* Read a directory item */
+FRESULT f_stat (const TCHAR*, FILINFO*); /* Get file status */
+FRESULT f_write (FIL*, const void*, UINT, UINT*); /* Write data to a file */
+FRESULT f_getfree (const TCHAR*, DWORD*, FATFS**); /* Get number of free clusters on the drive */
+FRESULT f_truncate (FIL*); /* Truncate file */
+FRESULT f_sync (FIL*); /* Flush cached data of a writing file */
+FRESULT f_unlink (const TCHAR*); /* Delete an existing file or directory */
+FRESULT f_mkdir (const TCHAR*); /* Create a new directory */
+FRESULT f_chmod (const TCHAR*, BYTE, BYTE); /* Change attriburte of the file/dir */
+FRESULT f_utime (const TCHAR*, const FILINFO*); /* Change timestamp of the file/dir */
+FRESULT f_rename (const TCHAR*, const TCHAR*); /* Rename/Move a file or directory */
+FRESULT f_chdrive (BYTE); /* Change current drive */
+FRESULT f_chdir (const TCHAR*); /* Change current directory */
+FRESULT f_getcwd (TCHAR*, UINT); /* Get current directory */
+FRESULT f_forward (FIL*, UINT(*)(const BYTE*,UINT), UINT, UINT*); /* Forward data to the stream */
+FRESULT f_mkfs (BYTE, BYTE, UINT); /* Create a file system on the drive */
+FRESULT f_fdisk (BYTE, const DWORD[], void*); /* Divide a physical drive into some partitions */
+int f_putc (TCHAR, FIL*); /* Put a character to the file */
+int f_puts (const TCHAR*, FIL*); /* Put a string to the file */
+int f_printf (FIL*, const TCHAR*, ...); /* Put a formatted string to the file */
+TCHAR* f_gets (TCHAR*, int, FIL*); /* Get a string from the file */
+
+#define f_eof(fp) (((fp)->fptr == (fp)->fsize) ? 1 : 0)
+#define f_error(fp) (((fp)->flag & FA__ERROR) ? 1 : 0)
+#define f_tell(fp) ((fp)->fptr)
+#define f_size(fp) ((fp)->fsize)
+
+#ifndef EOF
+#define EOF (-1)
+#endif
+
+
+
+
+/*--------------------------------------------------------------*/
+/* Additional user defined functions */
+
+/* RTC function */
+#if !_FS_READONLY
+DWORD get_fattime (void);
+#endif
+
+/* Unicode support functions */
+#if _USE_LFN /* Unicode - OEM code conversion */
+WCHAR ff_convert (WCHAR, UINT); /* OEM-Unicode bidirectional conversion */
+WCHAR ff_wtoupper (WCHAR); /* Unicode upper-case conversion */
+#if _USE_LFN == 3 /* Memory functions */
+void* ff_memalloc (UINT); /* Allocate memory block */
+void ff_memfree (void*); /* Free memory block */
+#endif
+#endif
+
+/* Sync functions */
+#if _FS_REENTRANT
+int ff_cre_syncobj (BYTE, _SYNC_t*);/* Create a sync object */
+int ff_req_grant (_SYNC_t); /* Lock sync object */
+void ff_rel_grant (_SYNC_t); /* Unlock sync object */
+int ff_del_syncobj (_SYNC_t); /* Delete a sync object */
+#endif
+
+
+
+
+/*--------------------------------------------------------------*/
+/* Flags and offset address */
+
+
+/* File access control and file status flags (FIL.flag) */
+
+#define FA_READ 0x01
+#define FA_OPEN_EXISTING 0x00
+#define FA__ERROR 0x80
+
+#if !_FS_READONLY
+#define FA_WRITE 0x02
+#define FA_CREATE_NEW 0x04
+#define FA_CREATE_ALWAYS 0x08
+#define FA_OPEN_ALWAYS 0x10
+#define FA__WRITTEN 0x20
+#define FA__DIRTY 0x40
+#endif
+
+
+/* FAT sub type (FATFS.fs_type) */
+
+#define FS_FAT12 1
+#define FS_FAT16 2
+#define FS_FAT32 3
+
+
+/* File attribute bits for directory entry */
+
+#define AM_RDO 0x01 /* Read only */
+#define AM_HID 0x02 /* Hidden */
+#define AM_SYS 0x04 /* System */
+#define AM_VOL 0x08 /* Volume label */
+#define AM_LFN 0x0F /* LFN entry */
+#define AM_DIR 0x10 /* Directory */
+#define AM_ARC 0x20 /* Archive */
+#define AM_MASK 0x3F /* Mask of defined bits */
+
+
+/* Fast seek feature */
+#define CREATE_LINKMAP 0xFFFFFFFF
+
+
+
+/*--------------------------------*/
+/* Multi-byte word access macros */
+
+#if _WORD_ACCESS == 1 /* Enable word access to the FAT structure */
+#define LD_WORD(ptr) (WORD)(*(WORD*)(BYTE*)(ptr))
+#define LD_DWORD(ptr) (DWORD)(*(DWORD*)(BYTE*)(ptr))
+#define ST_WORD(ptr,val) *(WORD*)(BYTE*)(ptr)=(WORD)(val)
+#define ST_DWORD(ptr,val) *(DWORD*)(BYTE*)(ptr)=(DWORD)(val)
+#else /* Use byte-by-byte access to the FAT structure */
+#define LD_WORD(ptr) (WORD)(((WORD)*((BYTE*)(ptr)+1)<<8)|(WORD)*(BYTE*)(ptr))
+#define LD_DWORD(ptr) (DWORD)(((DWORD)*((BYTE*)(ptr)+3)<<24)|((DWORD)*((BYTE*)(ptr)+2)<<16)|((WORD)*((BYTE*)(ptr)+1)<<8)|*(BYTE*)(ptr))
+#define ST_WORD(ptr,val) *(BYTE*)(ptr)=(BYTE)(val); *((BYTE*)(ptr)+1)=(BYTE)((WORD)(val)>>8)
+#define ST_DWORD(ptr,val) *(BYTE*)(ptr)=(BYTE)(val); *((BYTE*)(ptr)+1)=(BYTE)((WORD)(val)>>8); *((BYTE*)(ptr)+2)=(BYTE)((DWORD)(val)>>16); *((BYTE*)(ptr)+3)=(BYTE)((DWORD)(val)>>24)
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* _FATFS */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/FatFileSystem/ffconf.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,190 @@ +/*---------------------------------------------------------------------------/ +/ FatFs - FAT file system module configuration file R0.09 (C)ChaN, 2011 +/----------------------------------------------------------------------------/ +/ +/ CAUTION! Do not forget to make clean the project after any changes to +/ the configuration options. +/ +/----------------------------------------------------------------------------*/ +#ifndef _FFCONF +#define _FFCONF 6502 /* Revision ID */ + + +/*---------------------------------------------------------------------------/ +/ Functions and Buffer Configurations +/----------------------------------------------------------------------------*/ + +#define _FS_TINY 0 /* 0:Normal or 1:Tiny */ +/* When _FS_TINY is set to 1, FatFs uses the sector buffer in the file system +/ object instead of the sector buffer in the individual file object for file +/ data transfer. This reduces memory consumption 512 bytes each file object. */ + + +#define _FS_READONLY 0 /* 0:Read/Write or 1:Read only */ +/* Setting _FS_READONLY to 1 defines read only configuration. This removes +/ writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename, +/ f_truncate and useless f_getfree. */ + + +#define _FS_MINIMIZE 0 /* 0 to 3 */ +/* The _FS_MINIMIZE option defines minimization level to remove some functions. +/ +/ 0: Full function. +/ 1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename +/ are removed. +/ 2: f_opendir and f_readdir are removed in addition to 1. +/ 3: f_lseek is removed in addition to 2. */ + + +#define _USE_STRFUNC 0 /* 0:Disable or 1-2:Enable */ +/* To enable string functions, set _USE_STRFUNC to 1 or 2. */ + + +#define _USE_MKFS 1 /* 0:Disable or 1:Enable */ +/* To enable f_mkfs function, set _USE_MKFS to 1 and set _FS_READONLY to 0 */ + + +#define _USE_FORWARD 0 /* 0:Disable or 1:Enable */ +/* To enable f_forward function, set _USE_FORWARD to 1 and set _FS_TINY to 1. */ + + +#define _USE_FASTSEEK 0 /* 0:Disable or 1:Enable */ +/* To enable fast seek feature, set _USE_FASTSEEK to 1. */ + + + +/*---------------------------------------------------------------------------/ +/ Locale and Namespace Configurations +/----------------------------------------------------------------------------*/ + +#define _CODE_PAGE 858 +/* The _CODE_PAGE specifies the OEM code page to be used on the target system. +/ Incorrect setting of the code page can cause a file open failure. +/ +/ 932 - Japanese Shift-JIS (DBCS, OEM, Windows) +/ 936 - Simplified Chinese GBK (DBCS, OEM, Windows) +/ 949 - Korean (DBCS, OEM, Windows) +/ 950 - Traditional Chinese Big5 (DBCS, OEM, Windows) +/ 1250 - Central Europe (Windows) +/ 1251 - Cyrillic (Windows) +/ 1252 - Latin 1 (Windows) +/ 1253 - Greek (Windows) +/ 1254 - Turkish (Windows) +/ 1255 - Hebrew (Windows) +/ 1256 - Arabic (Windows) +/ 1257 - Baltic (Windows) +/ 1258 - Vietnam (OEM, Windows) +/ 437 - U.S. (OEM) +/ 720 - Arabic (OEM) +/ 737 - Greek (OEM) +/ 775 - Baltic (OEM) +/ 850 - Multilingual Latin 1 (OEM) +/ 858 - Multilingual Latin 1 + Euro (OEM) +/ 852 - Latin 2 (OEM) +/ 855 - Cyrillic (OEM) +/ 866 - Russian (OEM) +/ 857 - Turkish (OEM) +/ 862 - Hebrew (OEM) +/ 874 - Thai (OEM, Windows) +/ 1 - ASCII only (Valid for non LFN cfg.) +*/ + + +#define _USE_LFN 1 /* 0 to 3 */ +#define _MAX_LFN 255 /* Maximum LFN length to handle (12 to 255) */ +/* The _USE_LFN option switches the LFN support. +/ +/ 0: Disable LFN feature. _MAX_LFN and _LFN_UNICODE have no effect. +/ 1: Enable LFN with static working buffer on the BSS. Always NOT reentrant. +/ 2: Enable LFN with dynamic working buffer on the STACK. +/ 3: Enable LFN with dynamic working buffer on the HEAP. +/ +/ The LFN working buffer occupies (_MAX_LFN + 1) * 2 bytes. To enable LFN, +/ Unicode handling functions ff_convert() and ff_wtoupper() must be added +/ to the project. When enable to use heap, memory control functions +/ ff_memalloc() and ff_memfree() must be added to the project. */ + + +#define _LFN_UNICODE 0 /* 0:ANSI/OEM or 1:Unicode */ +/* To switch the character code set on FatFs API to Unicode, +/ enable LFN feature and set _LFN_UNICODE to 1. */ + + +#define _FS_RPATH 0 /* 0 to 2 */ +/* The _FS_RPATH option configures relative path feature. +/ +/ 0: Disable relative path feature and remove related functions. +/ 1: Enable relative path. f_chdrive() and f_chdir() are available. +/ 2: f_getcwd() is available in addition to 1. +/ +/ Note that output of the f_readdir fnction is affected by this option. */ + + + +/*---------------------------------------------------------------------------/ +/ Physical Drive Configurations +/----------------------------------------------------------------------------*/ + +#define _VOLUMES 4 +/* Number of volumes (logical drives) to be used. */ + + +#define _MAX_SS 512 /* 512, 1024, 2048 or 4096 */ +/* Maximum sector size to be handled. +/ Always set 512 for memory card and hard disk but a larger value may be +/ required for on-board flash memory, floppy disk and optical disk. +/ When _MAX_SS is larger than 512, it configures FatFs to variable sector size +/ and GET_SECTOR_SIZE command must be implememted to the disk_ioctl function. */ + + +#define _MULTI_PARTITION 0 /* 0:Single partition, 1/2:Enable multiple partition */ +/* When set to 0, each volume is bound to the same physical drive number and +/ it can mount only first primaly partition. When it is set to 1, each volume +/ is tied to the partitions listed in VolToPart[]. */ + + +#define _USE_ERASE 0 /* 0:Disable or 1:Enable */ +/* To enable sector erase feature, set _USE_ERASE to 1. CTRL_ERASE_SECTOR command +/ should be added to the disk_ioctl functio. */ + + + +/*---------------------------------------------------------------------------/ +/ System Configurations +/----------------------------------------------------------------------------*/ + +#define _WORD_ACCESS 0 /* 0 or 1 */ +/* Set 0 first and it is always compatible with all platforms. The _WORD_ACCESS +/ option defines which access method is used to the word data on the FAT volume. +/ +/ 0: Byte-by-byte access. +/ 1: Word access. Do not choose this unless following condition is met. +/ +/ When the byte order on the memory is big-endian or address miss-aligned word +/ access results incorrect behavior, the _WORD_ACCESS must be set to 0. +/ If it is not the case, the value can also be set to 1 to improve the +/ performance and code size. +*/ + + +/* A header file that defines sync object types on the O/S, such as +/ windows.h, ucos_ii.h and semphr.h, must be included prior to ff.h. */ + +#define _FS_REENTRANT 0 /* 0:Disable or 1:Enable */ +#define _FS_TIMEOUT 1000 /* Timeout period in unit of time ticks */ +#define _SYNC_t HANDLE /* O/S dependent type of sync object. e.g. HANDLE, OS_EVENT*, ID and etc.. */ + +/* The _FS_REENTRANT option switches the reentrancy (thread safe) of the FatFs module. +/ +/ 0: Disable reentrancy. _SYNC_t and _FS_TIMEOUT have no effect. +/ 1: Enable reentrancy. Also user provided synchronization handlers, +/ ff_req_grant, ff_rel_grant, ff_del_syncobj and ff_cre_syncobj +/ function must be added to the project. */ + + +#define _FS_SHARE 0 /* 0:Disable or >=1:Enable */ +/* To enable file shareing feature, set _FS_SHARE to 1 or greater. The value + defines how many files can be opened simultaneously. */ + + +#endif /* _FFCONFIG */
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/FatFileSystem/integer.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,37 @@ +/*-------------------------------------------*/ +/* Integer type definitions for FatFs module */ +/*-------------------------------------------*/ + +#ifndef _INTEGER +#define _INTEGER + +#ifdef _WIN32 /* FatFs development platform */ + +#include <windows.h> +#include <tchar.h> + +#else /* Embedded platform */ + +/* These types must be 16-bit, 32-bit or larger integer */ +typedef int INT; +typedef unsigned int UINT; + +/* These types must be 8-bit integer */ +typedef char CHAR; +typedef unsigned char UCHAR; +typedef unsigned char BYTE; + +/* These types must be 16-bit integer */ +typedef short SHORT; +typedef unsigned short USHORT; +typedef unsigned short WORD; +typedef unsigned short WCHAR; + +/* These types must be 32-bit integer */ +typedef long LONG; +typedef unsigned long ULONG; +typedef unsigned long DWORD; + +#endif + +#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/FatFileSystem/option/ccsbcs.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,540 @@
+/*------------------------------------------------------------------------*/
+/* Unicode - Local code bidirectional converter (C)ChaN, 2009 */
+/* (SBCS code pages) */
+/*------------------------------------------------------------------------*/
+/* 437 U.S. (OEM)
+/ 720 Arabic (OEM)
+/ 1256 Arabic (Windows)
+/ 737 Greek (OEM)
+/ 1253 Greek (Windows)
+/ 1250 Central Europe (Windows)
+/ 775 Baltic (OEM)
+/ 1257 Baltic (Windows)
+/ 850 Multilingual Latin 1 (OEM)
+/ 852 Latin 2 (OEM)
+/ 1252 Latin 1 (Windows)
+/ 855 Cyrillic (OEM)
+/ 1251 Cyrillic (Windows)
+/ 866 Russian (OEM)
+/ 857 Turkish (OEM)
+/ 1254 Turkish (Windows)
+/ 858 Multilingual Latin 1 + Euro (OEM)
+/ 862 Hebrew (OEM)
+/ 1255 Hebrew (Windows)
+/ 874 Thai (OEM, Windows)
+/ 1258 Vietnam (OEM, Windows)
+*/
+
+#include "../ff.h"
+
+
+#if _CODE_PAGE == 437
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP437(0x80-0xFF) to Unicode conversion table */
+ 0x00C7, 0x00FC, 0x00E9, 0x00E2, 0x00E4, 0x00E0, 0x00E5, 0x00E7,
+ 0x00EA, 0x00EB, 0x00E8, 0x00EF, 0x00EE, 0x00EC, 0x00C4, 0x00C5,
+ 0x00C9, 0x00E6, 0x00C6, 0x00F4, 0x00F6, 0x00F2, 0x00FB, 0x00F9,
+ 0x00FF, 0x00D6, 0x00DC, 0x00A2, 0x00A3, 0x00A5, 0x20A7, 0x0192,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x00F1, 0x00D1, 0x00AA, 0x00BA,
+ 0x00BF, 0x2310, 0x00AC, 0x00BD, 0x00BC, 0x00A1, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x2561, 0x2562, 0x2556,
+ 0x2555, 0x2563, 0x2551, 0x2557, 0x255D, 0x255C, 0x255B, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x255E, 0x255F,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x2567,
+ 0x2568, 0x2564, 0x2565, 0x2559, 0x2558, 0x2552, 0x2553, 0x256B,
+ 0x256A, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x03B1, 0x00DF, 0x0393, 0x03C0, 0x03A3, 0x03C3, 0x00B5, 0x03C4,
+ 0x03A6, 0x0398, 0x03A9, 0x03B4, 0x221E, 0x03C6, 0x03B5, 0x2229,
+ 0x2261, 0x00B1, 0x2265, 0x2264, 0x2320, 0x2321, 0x00F7, 0x2248,
+ 0x00B0, 0x2219, 0x00B7, 0x221A, 0x207F, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 720
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP720(0x80-0xFF) to Unicode conversion table */
+ 0x0000, 0x0000, 0x00E9, 0x00E2, 0x0000, 0x00E0, 0x0000, 0x00E7,
+ 0x00EA, 0x00EB, 0x00E8, 0x00EF, 0x00EE, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x0651, 0x0652, 0x00F4, 0x00A4, 0x0640, 0x00FB, 0x00F9,
+ 0x0621, 0x0622, 0x0623, 0x0624, 0x00A3, 0x0625, 0x0626, 0x0627,
+ 0x0628, 0x0629, 0x062A, 0x062B, 0x062C, 0x062D, 0x062E, 0x062F,
+ 0x0630, 0x0631, 0x0632, 0x0633, 0x0634, 0x0635, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x2561, 0x2562, 0x2556,
+ 0x2555, 0x2563, 0x2551, 0x2557, 0x255D, 0x255C, 0x255B, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x255E, 0x255F,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x2567,
+ 0x2568, 0x2564, 0x2565, 0x2559, 0x2558, 0x2552, 0x2553, 0x256B,
+ 0x256A, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x0636, 0x0637, 0x0638, 0x0639, 0x063A, 0x0641, 0x00B5, 0x0642,
+ 0x0643, 0x0644, 0x0645, 0x0646, 0x0647, 0x0648, 0x0649, 0x064A,
+ 0x2261, 0x064B, 0x064C, 0x064D, 0x064E, 0x064F, 0xO650, 0x2248,
+ 0x00B0, 0x2219, 0x00B7, 0x221A, 0x207F, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 737
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP737(0x80-0xFF) to Unicode conversion table */
+ 0x0391, 0x0392, 0x0393, 0x0394, 0x0395, 0x0396, 0x0397, 0x0398,
+ 0x0399, 0x039A, 0x039B, 0x039C, 0x039D, 0x039E, 0x039F, 0x03A0,
+ 0x03A1, 0x03A3, 0x03A4, 0x03A5, 0x03A6, 0x03A7, 0x03A8, 0x03A9,
+ 0x03B1, 0x03B2, 0x03B3, 0x03B4, 0x03B5, 0x03B6, 0x03B7, 0x03B8,
+ 0x03B9, 0x03BA, 0x03BB, 0x03BC, 0x03BD, 0x03BE, 0x03BF, 0x03C0,
+ 0x03C1, 0x03C3, 0x03C2, 0x03C4, 0x03C5, 0x03C6, 0x03C7, 0x03C8,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x2561, 0x2562, 0x2556,
+ 0x2555, 0x2563, 0x2551, 0x2557, 0x255D, 0x255C, 0x255B, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x255E, 0x255F,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x2567,
+ 0x2568, 0x2564, 0x2565, 0x2559, 0x2558, 0x2552, 0x2553, 0x256B,
+ 0x256A, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x03C9, 0x03AC, 0x03AD, 0x03AE, 0x03CA, 0x03AF, 0x03CC, 0x03CD,
+ 0x03CB, 0x03CE, 0x0386, 0x0388, 0x0389, 0x038A, 0x038C, 0x038E,
+ 0x038F, 0x00B1, 0x2265, 0x2264, 0x03AA, 0x03AB, 0x00F7, 0x2248,
+ 0x00B0, 0x2219, 0x00B7, 0x221A, 0x207F, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 775
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP775(0x80-0xFF) to Unicode conversion table */
+ 0x0106, 0x00FC, 0x00E9, 0x0101, 0x00E4, 0x0123, 0x00E5, 0x0107,
+ 0x0142, 0x0113, 0x0156, 0x0157, 0x012B, 0x0179, 0x00C4, 0x00C5,
+ 0x00C9, 0x00E6, 0x00C6, 0x014D, 0x00F6, 0x0122, 0x00A2, 0x015A,
+ 0x015B, 0x00D6, 0x00DC, 0x00F8, 0x00A3, 0x00D8, 0x00D7, 0x00A4,
+ 0x0100, 0x012A, 0x00F3, 0x017B, 0x017C, 0x017A, 0x201D, 0x00A6,
+ 0x00A9, 0x00AE, 0x00AC, 0x00BD, 0x00BC, 0x0141, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x0104, 0x010C, 0x0118,
+ 0x0116, 0x2563, 0x2551, 0x2557, 0x255D, 0x012E, 0x0160, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x0172, 0x016A,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x017D,
+ 0x0105, 0x010D, 0x0119, 0x0117, 0x012F, 0x0161, 0x0173, 0x016B,
+ 0x017E, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x00D3, 0x00DF, 0x014C, 0x0143, 0x00F5, 0x00D5, 0x00B5, 0x0144,
+ 0x0136, 0x0137, 0x013B, 0x013C, 0x0146, 0x0112, 0x0145, 0x2019,
+ 0x00AD, 0x00B1, 0x201C, 0x00BE, 0x00B6, 0x00A7, 0x00F7, 0x201E,
+ 0x00B0, 0x2219, 0x00B7, 0x00B9, 0x00B3, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 850
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP850(0x80-0xFF) to Unicode conversion table */
+ 0x00C7, 0x00FC, 0x00E9, 0x00E2, 0x00E4, 0x00E0, 0x00E5, 0x00E7,
+ 0x00EA, 0x00EB, 0x00E8, 0x00EF, 0x00EE, 0x00EC, 0x00C4, 0x00C5,
+ 0x00C9, 0x00E6, 0x00C6, 0x00F4, 0x00F6, 0x00F2, 0x00FB, 0x00F9,
+ 0x00FF, 0x00D6, 0x00DC, 0x00F8, 0x00A3, 0x00D8, 0x00D7, 0x0192,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x00F1, 0x00D1, 0x00AA, 0x00BA,
+ 0x00BF, 0x00AE, 0x00AC, 0x00BD, 0x00BC, 0x00A1, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x00C1, 0x00C2, 0x00C0,
+ 0x00A9, 0x2563, 0x2551, 0x2557, 0x255D, 0x00A2, 0x00A5, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x00E3, 0x00C3,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x00A4,
+ 0x00F0, 0x00D0, 0x00CA, 0x00CB, 0x00C8, 0x0131, 0x00CD, 0x00CE,
+ 0x00CF, 0x2518, 0x250C, 0x2588, 0x2584, 0x00A6, 0x00CC, 0x2580,
+ 0x00D3, 0x00DF, 0x00D4, 0x00D2, 0x00F5, 0x00D5, 0x00B5, 0x00FE,
+ 0x00DE, 0x00DA, 0x00DB, 0x00D9, 0x00FD, 0x00DD, 0x00AF, 0x00B4,
+ 0x00AD, 0x00B1, 0x2017, 0x00BE, 0x00B6, 0x00A7, 0x00F7, 0x00B8,
+ 0x00B0, 0x00A8, 0x00B7, 0x00B9, 0x00B3, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 852
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP852(0x80-0xFF) to Unicode conversion table */
+ 0x00C7, 0x00FC, 0x00E9, 0x00E2, 0x00E4, 0x016F, 0x0107, 0x00E7,
+ 0x0142, 0x00EB, 0x0150, 0x0151, 0x00EE, 0x0179, 0x00C4, 0x0106,
+ 0x00C9, 0x0139, 0x013A, 0x00F4, 0x00F6, 0x013D, 0x013E, 0x015A,
+ 0x015B, 0x00D6, 0x00DC, 0x0164, 0x0165, 0x0141, 0x00D7, 0x010D,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x0104, 0x0105, 0x017D, 0x017E,
+ 0x0118, 0x0119, 0x00AC, 0x017A, 0x010C, 0x015F, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x00C1, 0x00C2, 0x011A,
+ 0x015E, 0x2563, 0x2551, 0x2557, 0x255D, 0x017B, 0x017C, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x0102, 0x0103,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x00A4,
+ 0x0111, 0x0110, 0x010E, 0x00CB, 0x010F, 0x0147, 0x00CD, 0x00CE,
+ 0x011B, 0x2518, 0x250C, 0x2588, 0x2584, 0x0162, 0x016E, 0x2580,
+ 0x00D3, 0x00DF, 0x00D4, 0x0143, 0x0144, 0x0148, 0x0160, 0x0161,
+ 0x0154, 0x00DA, 0x0155, 0x0170, 0x00FD, 0x00DD, 0x0163, 0x00B4,
+ 0x00AD, 0x02DD, 0x02DB, 0x02C7, 0x02D8, 0x00A7, 0x00F7, 0x00B8,
+ 0x00B0, 0x00A8, 0x02D9, 0x0171, 0x0158, 0x0159, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 855
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP855(0x80-0xFF) to Unicode conversion table */
+ 0x0452, 0x0402, 0x0453, 0x0403, 0x0451, 0x0401, 0x0454, 0x0404,
+ 0x0455, 0x0405, 0x0456, 0x0406, 0x0457, 0x0407, 0x0458, 0x0408,
+ 0x0459, 0x0409, 0x045A, 0x040A, 0x045B, 0x040B, 0x045C, 0x040C,
+ 0x045E, 0x040E, 0x045F, 0x040F, 0x044E, 0x042E, 0x044A, 0x042A,
+ 0x0430, 0x0410, 0x0431, 0x0411, 0x0446, 0x0426, 0x0434, 0x0414,
+ 0x0435, 0x0415, 0x0444, 0x0424, 0x0433, 0x0413, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x0445, 0x0425, 0x0438,
+ 0x0418, 0x2563, 0x2551, 0x2557, 0x255D, 0x0439, 0x0419, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x043A, 0x041A,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x00A4,
+ 0x043B, 0x041B, 0x043C, 0x041C, 0x043D, 0x041D, 0x043E, 0x041E,
+ 0x043F, 0x2518, 0x250C, 0x2588, 0x2584, 0x041F, 0x044F, 0x2580,
+ 0x042F, 0x0440, 0x0420, 0x0441, 0x0421, 0x0442, 0x0422, 0x0443,
+ 0x0423, 0x0436, 0x0416, 0x0432, 0x0412, 0x044C, 0x042C, 0x2116,
+ 0x00AD, 0x044B, 0x042B, 0x0437, 0x0417, 0x0448, 0x0428, 0x044D,
+ 0x042D, 0x0449, 0x0429, 0x0447, 0x0427, 0x00A7, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 857
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP857(0x80-0xFF) to Unicode conversion table */
+ 0x00C7, 0x00FC, 0x00E9, 0x00E2, 0x00E4, 0x00E0, 0x00E5, 0x00E7,
+ 0x00EA, 0x00EB, 0x00E8, 0x00EF, 0x00EE, 0x0131, 0x00C4, 0x00C5,
+ 0x00C9, 0x00E6, 0x00C6, 0x00F4, 0x00F6, 0x00F2, 0x00FB, 0x00F9,
+ 0x0130, 0x00D6, 0x00DC, 0x00F8, 0x00A3, 0x00D8, 0x015E, 0x015F,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x00F1, 0x00D1, 0x011E, 0x011F,
+ 0x00BF, 0x00AE, 0x00AC, 0x00BD, 0x00BC, 0x00A1, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x00C1, 0x00C2, 0x00C0,
+ 0x00A9, 0x2563, 0x2551, 0x2557, 0x255D, 0x00A2, 0x00A5, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x00E3, 0x00C3,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x00A4,
+ 0x00BA, 0x00AA, 0x00CA, 0x00CB, 0x00C8, 0x0000, 0x00CD, 0x00CE,
+ 0x00CF, 0x2518, 0x250C, 0x2588, 0x2584, 0x00A6, 0x00CC, 0x2580,
+ 0x00D3, 0x00DF, 0x00D4, 0x00D2, 0x00F5, 0x00D5, 0x00B5, 0x0000,
+ 0x00D7, 0x00DA, 0x00DB, 0x00D9, 0x00EC, 0x00FF, 0x00AF, 0x00B4,
+ 0x00AD, 0x00B1, 0x0000, 0x00BE, 0x00B6, 0x00A7, 0x00F7, 0x00B8,
+ 0x00B0, 0x00A8, 0x00B7, 0x00B9, 0x00B3, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 858
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP858(0x80-0xFF) to Unicode conversion table */
+ 0x00C7, 0x00FC, 0x00E9, 0x00E2, 0x00E4, 0x00E0, 0x00E5, 0x00E7,
+ 0x00EA, 0x00EB, 0x00E8, 0x00EF, 0x00EE, 0x00EC, 0x00C4, 0x00C5,
+ 0x00C9, 0x00E6, 0x00C6, 0x00F4, 0x00F6, 0x00F2, 0x00FB, 0x00F9,
+ 0x00FF, 0x00D6, 0x00DC, 0x00F8, 0x00A3, 0x00D8, 0x00D7, 0x0192,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x00F1, 0x00D1, 0x00AA, 0x00BA,
+ 0x00BF, 0x00AE, 0x00AC, 0x00BD, 0x00BC, 0x00A1, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x00C1, 0x00C2, 0x00C0,
+ 0x00A9, 0x2563, 0x2551, 0x2557, 0x2550, 0x00A2, 0x00A5, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x00E3, 0x00C3,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x00A4,
+ 0x00F0, 0x00D0, 0x00CA, 0x00CB, 0x00C8, 0x20AC, 0x00CD, 0x00CE,
+ 0x00CF, 0x2518, 0x250C, 0x2588, 0x2584, 0x00C6, 0x00CC, 0x2580,
+ 0x00D3, 0x00DF, 0x00D4, 0x00D2, 0x00F5, 0x00D5, 0x00B5, 0x00FE,
+ 0x00DE, 0x00DA, 0x00DB, 0x00D9, 0x00FD, 0x00DD, 0x00AF, 0x00B4,
+ 0x00AD, 0x00B1, 0x2017, 0x00BE, 0x00B6, 0x00A7, 0x00F7, 0x00B8,
+ 0x00B0, 0x00A8, 0x00B7, 0x00B9, 0x00B3, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 862
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP862(0x80-0xFF) to Unicode conversion table */
+ 0x05D0, 0x05D1, 0x05D2, 0x05D3, 0x05D4, 0x05D5, 0x05D6, 0x05D7,
+ 0x05D8, 0x05D9, 0x05DA, 0x05DB, 0x05DC, 0x05DD, 0x05DE, 0x05DF,
+ 0x05E0, 0x05E1, 0x05E2, 0x05E3, 0x05E4, 0x05E5, 0x05E6, 0x05E7,
+ 0x05E8, 0x05E9, 0x05EA, 0x00A2, 0x00A3, 0x00A5, 0x20A7, 0x0192,
+ 0x00E1, 0x00ED, 0x00F3, 0x00FA, 0x00F1, 0x00D1, 0x00AA, 0x00BA,
+ 0x00BF, 0x2310, 0x00AC, 0x00BD, 0x00BC, 0x00A1, 0x00AB, 0x00BB,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x2561, 0x2562, 0x2556,
+ 0x2555, 0x2563, 0x2551, 0x2557, 0x255D, 0x255C, 0x255B, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x255E, 0x255F,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x2567,
+ 0x2568, 0x2564, 0x2565, 0x2559, 0x2558, 0x2552, 0x2553, 0x256B,
+ 0x256A, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x03B1, 0x00DF, 0x0393, 0x03C0, 0x03A3, 0x03C3, 0x00B5, 0x03C4,
+ 0x03A6, 0x0398, 0x03A9, 0x03B4, 0x221E, 0x03C6, 0x03B5, 0x2229,
+ 0x2261, 0x00B1, 0x2265, 0x2264, 0x2320, 0x2321, 0x00F7, 0x2248,
+ 0x00B0, 0x2219, 0x00B7, 0x221A, 0x207F, 0x00B2, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 866
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP866(0x80-0xFF) to Unicode conversion table */
+ 0x0410, 0x0411, 0x0412, 0x0413, 0x0414, 0x0415, 0x0416, 0x0417,
+ 0x0418, 0x0419, 0x041A, 0x041B, 0x041C, 0x041D, 0x041E, 0x041F,
+ 0x0420, 0x0421, 0x0422, 0x0423, 0x0424, 0x0425, 0x0426, 0x0427,
+ 0x0428, 0x0429, 0x042A, 0x042B, 0x042C, 0x042D, 0x042E, 0x042F,
+ 0x0430, 0x0431, 0x0432, 0x0433, 0x0434, 0x0435, 0x0436, 0x0437,
+ 0x0438, 0x0439, 0x043A, 0x043B, 0x043C, 0x043D, 0x043E, 0x043F,
+ 0x2591, 0x2592, 0x2593, 0x2502, 0x2524, 0x2561, 0x2562, 0x2556,
+ 0x2555, 0x2563, 0x2551, 0x2557, 0x255D, 0x255C, 0x255B, 0x2510,
+ 0x2514, 0x2534, 0x252C, 0x251C, 0x2500, 0x253C, 0x255E, 0x255F,
+ 0x255A, 0x2554, 0x2569, 0x2566, 0x2560, 0x2550, 0x256C, 0x2567,
+ 0x2568, 0x2564, 0x2565, 0x2559, 0x2558, 0x2552, 0x2553, 0x256B,
+ 0x256A, 0x2518, 0x250C, 0x2588, 0x2584, 0x258C, 0x2590, 0x2580,
+ 0x0440, 0x0441, 0x0442, 0x0443, 0x0444, 0x0445, 0x0446, 0x0447,
+ 0x0448, 0x0449, 0x044A, 0x044B, 0x044C, 0x044D, 0x044E, 0x044F,
+ 0x0401, 0x0451, 0x0404, 0x0454, 0x0407, 0x0457, 0x040E, 0x045E,
+ 0x00B0, 0x2219, 0x00B7, 0x221A, 0x2116, 0x00A4, 0x25A0, 0x00A0
+};
+
+#elif _CODE_PAGE == 874
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP874(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x0000, 0x0000, 0x0000, 0x2026, 0x0000, 0x0000,
+ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x00A0, 0x0E01, 0x0E02, 0x0E03, 0x0E04, 0x0E05, 0x0E06, 0x0E07,
+ 0x0E08, 0x0E09, 0x0E0A, 0x0E0B, 0x0E0C, 0x0E0D, 0x0E0E, 0x0E0F,
+ 0x0E10, 0x0E11, 0x0E12, 0x0E13, 0x0E14, 0x0E15, 0x0E16, 0x0E17,
+ 0x0E18, 0x0E19, 0x0E1A, 0x0E1B, 0x0E1C, 0x0E1D, 0x0E1E, 0x0E1F,
+ 0x0E20, 0x0E21, 0x0E22, 0x0E23, 0x0E24, 0x0E25, 0x0E26, 0x0E27,
+ 0x0E28, 0x0E29, 0x0E2A, 0x0E2B, 0x0E2C, 0x0E2D, 0x0E2E, 0x0E2F,
+ 0x0E30, 0x0E31, 0x0E32, 0x0E33, 0x0E34, 0x0E35, 0x0E36, 0x0E37,
+ 0x0E38, 0x0E39, 0x0E3A, 0x0000, 0x0000, 0x0000, 0x0000, 0x0E3F,
+ 0x0E40, 0x0E41, 0x0E42, 0x0E43, 0x0E44, 0x0E45, 0x0E46, 0x0E47,
+ 0x0E48, 0x0E49, 0x0E4A, 0x0E4B, 0x0E4C, 0x0E4D, 0x0E4E, 0x0E4F,
+ 0x0E50, 0x0E51, 0x0E52, 0x0E53, 0x0E54, 0x0E55, 0x0E56, 0x0E57,
+ 0x0E58, 0x0E59, 0x0E5A, 0x0E5B, 0x0000, 0x0000, 0x0000, 0x0000
+};
+
+#elif _CODE_PAGE == 1250
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1250(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0000, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x0000, 0x2030, 0x0160, 0x2039, 0x015A, 0x0164, 0x017D, 0x0179,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x0000, 0x2122, 0x0161, 0x203A, 0x015B, 0x0165, 0x017E, 0x017A,
+ 0x00A0, 0x02C7, 0x02D8, 0x0141, 0x00A4, 0x0104, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x015E, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x017B,
+ 0x00B0, 0x00B1, 0x02DB, 0x0142, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x0105, 0x015F, 0x00BB, 0x013D, 0x02DD, 0x013E, 0x017C,
+ 0x0154, 0x00C1, 0x00C2, 0x0102, 0x00C4, 0x0139, 0x0106, 0x00C7,
+ 0x010C, 0x00C9, 0x0118, 0x00CB, 0x011A, 0x00CD, 0x00CE, 0x010E,
+ 0x0110, 0x0143, 0x0147, 0x00D3, 0x00D4, 0x0150, 0x00D6, 0x00D7,
+ 0x0158, 0x016E, 0x00DA, 0x0170, 0x00DC, 0x00DD, 0x0162, 0x00DF,
+ 0x0155, 0x00E1, 0x00E2, 0x0103, 0x00E4, 0x013A, 0x0107, 0x00E7,
+ 0x010D, 0x00E9, 0x0119, 0x00EB, 0x011B, 0x00ED, 0x00EE, 0x010F,
+ 0x0111, 0x0144, 0x0148, 0x00F3, 0x00F4, 0x0151, 0x00F6, 0x00F7,
+ 0x0159, 0x016F, 0x00FA, 0x0171, 0x00FC, 0x00FD, 0x0163, 0x02D9
+};
+
+#elif _CODE_PAGE == 1251
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1251(0x80-0xFF) to Unicode conversion table */
+ 0x0402, 0x0403, 0x201A, 0x0453, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x20AC, 0x2030, 0x0409, 0x2039, 0x040A, 0x040C, 0x040B, 0x040F,
+ 0x0452, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x0000, 0x2111, 0x0459, 0x203A, 0x045A, 0x045C, 0x045B, 0x045F,
+ 0x00A0, 0x040E, 0x045E, 0x0408, 0x00A4, 0x0490, 0x00A6, 0x00A7,
+ 0x0401, 0x00A9, 0x0404, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x0407,
+ 0x00B0, 0x00B1, 0x0406, 0x0456, 0x0491, 0x00B5, 0x00B6, 0x00B7,
+ 0x0451, 0x2116, 0x0454, 0x00BB, 0x0458, 0x0405, 0x0455, 0x0457,
+ 0x0410, 0x0411, 0x0412, 0x0413, 0x0414, 0x0415, 0x0416, 0x0417,
+ 0x0418, 0x0419, 0x041A, 0x041B, 0x041C, 0x041D, 0x041E, 0x041F,
+ 0x0420, 0x0421, 0x0422, 0x0423, 0x0424, 0x0425, 0x0426, 0x0427,
+ 0x0428, 0x0429, 0x042A, 0x042B, 0x042C, 0x042D, 0x042E, 0x042F,
+ 0x0430, 0x0431, 0x0432, 0x0433, 0x0434, 0x0435, 0x0436, 0x0437,
+ 0x0438, 0x0439, 0x043A, 0x043B, 0x043C, 0x043D, 0x043E, 0x043F,
+ 0x0440, 0x0441, 0x0442, 0x0443, 0x0444, 0x0445, 0x0446, 0x0447,
+ 0x0448, 0x0449, 0x044A, 0x044B, 0x044C, 0x044D, 0x044E, 0x044F
+};
+
+#elif _CODE_PAGE == 1252
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1252(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x02C6, 0x2030, 0x0160, 0x2039, 0x0152, 0x0000, 0x017D, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x02DC, 0x2122, 0x0161, 0x203A, 0x0153, 0x0000, 0x017E, 0x0178,
+ 0x00A0, 0x00A1, 0x00A2, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x00AA, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x00BA, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x00BF,
+ 0x00C0, 0x00C1, 0x00C2, 0x00C3, 0x00C4, 0x00C5, 0x00C6, 0x00C7,
+ 0x00C8, 0x00C9, 0x00CA, 0x00CB, 0x00CC, 0x00CD, 0x00CE, 0x00CF,
+ 0x00D0, 0x00D1, 0x00D2, 0x00D3, 0x00D4, 0x00D5, 0x00D6, 0x00D7,
+ 0x00D8, 0x00D9, 0x00DA, 0x00DB, 0x00DC, 0x00DD, 0x00DE, 0x00DF,
+ 0x00E0, 0x00E1, 0x00E2, 0x00E3, 0x00E4, 0x00E5, 0x00E6, 0x00E7,
+ 0x00E8, 0x00E9, 0x00EA, 0x00EB, 0x00EC, 0x00ED, 0x00EE, 0x00EF,
+ 0x00F0, 0x00F1, 0x00F2, 0x00F3, 0x00F4, 0x00F5, 0x00F6, 0x00F7,
+ 0x00F8, 0x00F9, 0x00FA, 0x00FB, 0x00FC, 0x00FD, 0x00FE, 0x00FF
+};
+
+#elif _CODE_PAGE == 1253
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1253(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x0000, 0x2030, 0x0000, 0x2039, 0x000C, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x0000, 0x2122, 0x0000, 0x203A, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x00A0, 0x0385, 0x0386, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x0000, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x2015,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x0384, 0x00B5, 0x00B6, 0x00B7,
+ 0x0388, 0x0389, 0x038A, 0x00BB, 0x038C, 0x00BD, 0x038E, 0x038F,
+ 0x0390, 0x0391, 0x0392, 0x0393, 0x0394, 0x0395, 0x0396, 0x0397,
+ 0x0398, 0x0399, 0x039A, 0x039B, 0x039C, 0x039D, 0x039E, 0x039F,
+ 0x03A0, 0x03A1, 0x0000, 0x03A3, 0x03A4, 0x03A5, 0x03A6, 0x03A7,
+ 0x03A8, 0x03A9, 0x03AA, 0x03AD, 0x03AC, 0x03AD, 0x03AE, 0x03AF,
+ 0x03B0, 0x03B1, 0x03B2, 0x03B3, 0x03B4, 0x03B5, 0x03B6, 0x03B7,
+ 0x03B8, 0x03B9, 0x03BA, 0x03BB, 0x03BC, 0x03BD, 0x03BE, 0x03BF,
+ 0x03C0, 0x03C1, 0x03C2, 0x03C3, 0x03C4, 0x03C5, 0x03C6, 0x03C7,
+ 0x03C8, 0x03C9, 0x03CA, 0x03CB, 0x03CC, 0x03CD, 0x03CE, 0x0000
+};
+
+#elif _CODE_PAGE == 1254
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1254(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x210A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x02C6, 0x2030, 0x0160, 0x2039, 0x0152, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x02DC, 0x2122, 0x0161, 0x203A, 0x0153, 0x0000, 0x0000, 0x0178,
+ 0x00A0, 0x00A1, 0x00A2, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x00AA, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x00BA, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x00BF,
+ 0x00C0, 0x00C1, 0x00C2, 0x00C3, 0x00C4, 0x00C5, 0x00C6, 0x00C7,
+ 0x00C8, 0x00C9, 0x00CA, 0x00CB, 0x00CC, 0x00CD, 0x00CE, 0x00CF,
+ 0x011E, 0x00D1, 0x00D2, 0x00D3, 0x00D4, 0x00D5, 0x00D6, 0x00D7,
+ 0x00D8, 0x00D9, 0x00DA, 0x00BD, 0x00DC, 0x0130, 0x015E, 0x00DF,
+ 0x00E0, 0x00E1, 0x00E2, 0x00E3, 0x00E4, 0x00E5, 0x00E6, 0x00E7,
+ 0x00E8, 0x00E9, 0x00EA, 0x00EB, 0x00EC, 0x00ED, 0x00EE, 0x00EF,
+ 0x011F, 0x00F1, 0x00F2, 0x00F3, 0x00F4, 0x00F5, 0x00F6, 0x00F7,
+ 0x00F8, 0x00F9, 0x00FA, 0x00FB, 0x00FC, 0x0131, 0x015F, 0x00FF
+};
+
+#elif _CODE_PAGE == 1255
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1255(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x02C6, 0x2030, 0x0000, 0x2039, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x02DC, 0x2122, 0x0000, 0x203A, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x00A0, 0x00A1, 0x00A2, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x00D7, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x00F7, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x00BF,
+ 0x05B0, 0x05B1, 0x05B2, 0x05B3, 0x05B4, 0x05B5, 0x05B6, 0x05B7,
+ 0x05B8, 0x05B9, 0x0000, 0x05BB, 0x05BC, 0x05BD, 0x05BE, 0x05BF,
+ 0x05C0, 0x05C1, 0x05C2, 0x05C3, 0x05F0, 0x05F1, 0x05F2, 0x05F3,
+ 0x05F4, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
+ 0x05D0, 0x05D1, 0x05D2, 0x05D3, 0x05D4, 0x05D5, 0x05D6, 0x05D7,
+ 0x05D8, 0x05D9, 0x05DA, 0x05DB, 0x05DC, 0x05DD, 0x05DE, 0x05DF,
+ 0x05E0, 0x05E1, 0x05E2, 0x05E3, 0x05E4, 0x05E5, 0x05E6, 0x05E7,
+ 0x05E8, 0x05E9, 0x05EA, 0x0000, 0x0000, 0x200E, 0x200F, 0x0000
+};
+
+#elif _CODE_PAGE == 1256
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1256(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x067E, 0x201A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x02C6, 0x2030, 0x0679, 0x2039, 0x0152, 0x0686, 0x0698, 0x0688,
+ 0x06AF, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x06A9, 0x2122, 0x0691, 0x203A, 0x0153, 0x200C, 0x200D, 0x06BA,
+ 0x00A0, 0x060C, 0x00A2, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x06BE, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x061B, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x061F,
+ 0x06C1, 0x0621, 0x0622, 0x0623, 0x0624, 0x0625, 0x0626, 0x0627,
+ 0x0628, 0x0629, 0x062A, 0x062B, 0x062C, 0x062D, 0x062E, 0x062F,
+ 0x0630, 0x0631, 0x0632, 0x0633, 0x0634, 0x0635, 0x0636, 0x00D7,
+ 0x0637, 0x0638, 0x0639, 0x063A, 0x0640, 0x0640, 0x0642, 0x0643,
+ 0x00E0, 0x0644, 0x00E2, 0x0645, 0x0646, 0x0647, 0x0648, 0x00E7,
+ 0x00E8, 0x00E9, 0x00EA, 0x00EB, 0x0649, 0x064A, 0x00EE, 0x00EF,
+ 0x064B, 0x064C, 0x064D, 0x064E, 0x00F4, 0x064F, 0x0650, 0x00F7,
+ 0x0651, 0x00F9, 0x0652, 0x00FB, 0x00FC, 0x200E, 0x200F, 0x06D2
+}
+
+#elif _CODE_PAGE == 1257
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1257(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0000, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x0000, 0x2030, 0x0000, 0x2039, 0x0000, 0x00A8, 0x02C7, 0x00B8,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x0000, 0x2122, 0x0000, 0x203A, 0x0000, 0x00AF, 0x02DB, 0x0000,
+ 0x00A0, 0x0000, 0x00A2, 0x00A3, 0x00A4, 0x0000, 0x00A6, 0x00A7,
+ 0x00D8, 0x00A9, 0x0156, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x0157, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x00E6,
+ 0x0104, 0x012E, 0x0100, 0x0106, 0x00C4, 0x00C5, 0x0118, 0x0112,
+ 0x010C, 0x00C9, 0x0179, 0x0116, 0x0122, 0x0136, 0x012A, 0x013B,
+ 0x0160, 0x0143, 0x0145, 0x00D3, 0x014C, 0x00D5, 0x00D6, 0x00D7,
+ 0x0172, 0x0141, 0x015A, 0x016A, 0x00DC, 0x017B, 0x017D, 0x00DF,
+ 0x0105, 0x012F, 0x0101, 0x0107, 0x00E4, 0x00E5, 0x0119, 0x0113,
+ 0x010D, 0x00E9, 0x017A, 0x0117, 0x0123, 0x0137, 0x012B, 0x013C,
+ 0x0161, 0x0144, 0x0146, 0x00F3, 0x014D, 0x00F5, 0x00F6, 0x00F7,
+ 0x0173, 0x014E, 0x015B, 0x016B, 0x00FC, 0x017C, 0x017E, 0x02D9
+};
+
+#elif _CODE_PAGE == 1258
+#define _TBLDEF 1
+static
+const WCHAR Tbl[] = { /* CP1258(0x80-0xFF) to Unicode conversion table */
+ 0x20AC, 0x0000, 0x201A, 0x0192, 0x201E, 0x2026, 0x2020, 0x2021,
+ 0x02C6, 0x2030, 0x0000, 0x2039, 0x0152, 0x0000, 0x0000, 0x0000,
+ 0x0000, 0x2018, 0x2019, 0x201C, 0x201D, 0x2022, 0x2013, 0x2014,
+ 0x02DC, 0x2122, 0x0000, 0x203A, 0x0153, 0x0000, 0x0000, 0x0178,
+ 0x00A0, 0x00A1, 0x00A2, 0x00A3, 0x00A4, 0x00A5, 0x00A6, 0x00A7,
+ 0x00A8, 0x00A9, 0x00AA, 0x00AB, 0x00AC, 0x00AD, 0x00AE, 0x00AF,
+ 0x00B0, 0x00B1, 0x00B2, 0x00B3, 0x00B4, 0x00B5, 0x00B6, 0x00B7,
+ 0x00B8, 0x00B9, 0x00BA, 0x00BB, 0x00BC, 0x00BD, 0x00BE, 0x00BF,
+ 0x00C0, 0x00C1, 0x00C2, 0x0102, 0x00C4, 0x00C5, 0x00C6, 0x00C7,
+ 0x00C8, 0x00C9, 0x00CA, 0x00CB, 0x0300, 0x00CD, 0x00CE, 0x00CF,
+ 0x0110, 0x00D1, 0x0309, 0x00D3, 0x00D4, 0x01A0, 0x00D6, 0x00D7,
+ 0x00D8, 0x00D9, 0x00DA, 0x00DB, 0x00DC, 0x01AF, 0x0303, 0x00DF,
+ 0x00E0, 0x00E1, 0x00E2, 0x0103, 0x00E4, 0x00E5, 0x00E6, 0x00E7,
+ 0x00E8, 0x00E9, 0x00EA, 0x00EB, 0x0301, 0x00ED, 0x00EE, 0x00EF,
+ 0x0111, 0x00F1, 0x0323, 0x00F3, 0x00F4, 0x01A1, 0x00F6, 0x00F7,
+ 0x00F8, 0x00F9, 0x00FA, 0x00FB, 0x00FC, 0x01B0, 0x20AB, 0x00FF
+};
+
+#endif
+
+
+#if !_TBLDEF || !_USE_LFN
+#error This file is not needed in current configuration. Remove from the project.
+#endif
+
+
+WCHAR ff_convert ( /* Converted character, Returns zero on error */
+ WCHAR src, /* Character code to be converted */
+ UINT dir /* 0: Unicode to OEMCP, 1: OEMCP to Unicode */
+)
+{
+ WCHAR c;
+
+
+ if (src < 0x80) { /* ASCII */
+ c = src;
+
+ } else {
+ if (dir) { /* OEMCP to Unicode */
+ c = (src >= 0x100) ? 0 : Tbl[src - 0x80];
+
+ } else { /* Unicode to OEMCP */
+ for (c = 0; c < 0x80; c++) {
+ if (src == Tbl[c]) break;
+ }
+ c = (c + 0x80) & 0xFF;
+ }
+ }
+
+ return c;
+}
+
+
+WCHAR ff_wtoupper ( /* Upper converted character */
+ WCHAR chr /* Input character */
+)
+{
+ static const WCHAR tbl_lower[] = { 0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67, 0x68, 0x69, 0x6A, 0x6B, 0x6C, 0x6D, 0x6E, 0x6F, 0x70, 0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77, 0x78, 0x79, 0x7A, 0xA1, 0x00A2, 0x00A3, 0x00A5, 0x00AC, 0x00AF, 0xE0, 0xE1, 0xE2, 0xE3, 0xE4, 0xE5, 0xE6, 0xE7, 0xE8, 0xE9, 0xEA, 0xEB, 0xEC, 0xED, 0xEE, 0xEF, 0xF0, 0xF1, 0xF2, 0xF3, 0xF4, 0xF5, 0xF6, 0xF8, 0xF9, 0xFA, 0xFB, 0xFC, 0xFD, 0xFE, 0x0FF, 0x101, 0x103, 0x105, 0x107, 0x109, 0x10B, 0x10D, 0x10F, 0x111, 0x113, 0x115, 0x117, 0x119, 0x11B, 0x11D, 0x11F, 0x121, 0x123, 0x125, 0x127, 0x129, 0x12B, 0x12D, 0x12F, 0x131, 0x133, 0x135, 0x137, 0x13A, 0x13C, 0x13E, 0x140, 0x142, 0x144, 0x146, 0x148, 0x14B, 0x14D, 0x14F, 0x151, 0x153, 0x155, 0x157, 0x159, 0x15B, 0x15D, 0x15F, 0x161, 0x163, 0x165, 0x167, 0x169, 0x16B, 0x16D, 0x16F, 0x171, 0x173, 0x175, 0x177, 0x17A, 0x17C, 0x17E, 0x192, 0x3B1, 0x3B2, 0x3B3, 0x3B4, 0x3B5, 0x3B6, 0x3B7, 0x3B8, 0x3B9, 0x3BA, 0x3BB, 0x3BC, 0x3BD, 0x3BE, 0x3BF, 0x3C0, 0x3C1, 0x3C3, 0x3C4, 0x3C5, 0x3C6, 0x3C7, 0x3C8, 0x3C9, 0x3CA, 0x430, 0x431, 0x432, 0x433, 0x434, 0x435, 0x436, 0x437, 0x438, 0x439, 0x43A, 0x43B, 0x43C, 0x43D, 0x43E, 0x43F, 0x440, 0x441, 0x442, 0x443, 0x444, 0x445, 0x446, 0x447, 0x448, 0x449, 0x44A, 0x44B, 0x44C, 0x44D, 0x44E, 0x44F, 0x451, 0x452, 0x453, 0x454, 0x455, 0x456, 0x457, 0x458, 0x459, 0x45A, 0x45B, 0x45C, 0x45E, 0x45F, 0x2170, 0x2171, 0x2172, 0x2173, 0x2174, 0x2175, 0x2176, 0x2177, 0x2178, 0x2179, 0x217A, 0x217B, 0x217C, 0x217D, 0x217E, 0x217F, 0xFF41, 0xFF42, 0xFF43, 0xFF44, 0xFF45, 0xFF46, 0xFF47, 0xFF48, 0xFF49, 0xFF4A, 0xFF4B, 0xFF4C, 0xFF4D, 0xFF4E, 0xFF4F, 0xFF50, 0xFF51, 0xFF52, 0xFF53, 0xFF54, 0xFF55, 0xFF56, 0xFF57, 0xFF58, 0xFF59, 0xFF5A, 0 };
+ static const WCHAR tbl_upper[] = { 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47, 0x48, 0x49, 0x4A, 0x4B, 0x4C, 0x4D, 0x4E, 0x4F, 0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57, 0x58, 0x59, 0x5A, 0x21, 0xFFE0, 0xFFE1, 0xFFE5, 0xFFE2, 0xFFE3, 0xC0, 0xC1, 0xC2, 0xC3, 0xC4, 0xC5, 0xC6, 0xC7, 0xC8, 0xC9, 0xCA, 0xCB, 0xCC, 0xCD, 0xCE, 0xCF, 0xD0, 0xD1, 0xD2, 0xD3, 0xD4, 0xD5, 0xD6, 0xD8, 0xD9, 0xDA, 0xDB, 0xDC, 0xDD, 0xDE, 0x178, 0x100, 0x102, 0x104, 0x106, 0x108, 0x10A, 0x10C, 0x10E, 0x110, 0x112, 0x114, 0x116, 0x118, 0x11A, 0x11C, 0x11E, 0x120, 0x122, 0x124, 0x126, 0x128, 0x12A, 0x12C, 0x12E, 0x130, 0x132, 0x134, 0x136, 0x139, 0x13B, 0x13D, 0x13F, 0x141, 0x143, 0x145, 0x147, 0x14A, 0x14C, 0x14E, 0x150, 0x152, 0x154, 0x156, 0x158, 0x15A, 0x15C, 0x15E, 0x160, 0x162, 0x164, 0x166, 0x168, 0x16A, 0x16C, 0x16E, 0x170, 0x172, 0x174, 0x176, 0x179, 0x17B, 0x17D, 0x191, 0x391, 0x392, 0x393, 0x394, 0x395, 0x396, 0x397, 0x398, 0x399, 0x39A, 0x39B, 0x39C, 0x39D, 0x39E, 0x39F, 0x3A0, 0x3A1, 0x3A3, 0x3A4, 0x3A5, 0x3A6, 0x3A7, 0x3A8, 0x3A9, 0x3AA, 0x410, 0x411, 0x412, 0x413, 0x414, 0x415, 0x416, 0x417, 0x418, 0x419, 0x41A, 0x41B, 0x41C, 0x41D, 0x41E, 0x41F, 0x420, 0x421, 0x422, 0x423, 0x424, 0x425, 0x426, 0x427, 0x428, 0x429, 0x42A, 0x42B, 0x42C, 0x42D, 0x42E, 0x42F, 0x401, 0x402, 0x403, 0x404, 0x405, 0x406, 0x407, 0x408, 0x409, 0x40A, 0x40B, 0x40C, 0x40E, 0x40F, 0x2160, 0x2161, 0x2162, 0x2163, 0x2164, 0x2165, 0x2166, 0x2167, 0x2168, 0x2169, 0x216A, 0x216B, 0x216C, 0x216D, 0x216E, 0x216F, 0xFF21, 0xFF22, 0xFF23, 0xFF24, 0xFF25, 0xFF26, 0xFF27, 0xFF28, 0xFF29, 0xFF2A, 0xFF2B, 0xFF2C, 0xFF2D, 0xFF2E, 0xFF2F, 0xFF30, 0xFF31, 0xFF32, 0xFF33, 0xFF34, 0xFF35, 0xFF36, 0xFF37, 0xFF38, 0xFF39, 0xFF3A, 0 };
+ int i;
+
+
+ for (i = 0; tbl_lower[i] && chr != tbl_lower[i]; i++) ;
+
+ return tbl_lower[i] ? tbl_upper[i] : chr;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/ChangeLog.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,165 @@
+/* $Id:$
+
+1.23 25th July 2012
+
+ * LPC1768 code as was. This release includes "alpha" support for the LPC11U24
+
+1.22 19th April 2012
+
+ * http://mbed.org/forum/bugs-suggestions/topic/2936/
+ * Bug fix, protect important buffer pointers from IRQ corruption.
+ Credits:
+ Anthony Wieser http://mbed.org/users/WieserSoftwareLtd/ for the fix.
+ BlazeX http://mbed.org/users/BlazeX/ for the alert that a fix was needed!
+
+1.21 10 May 2011
+
+ * http://mbed.org/forum/mbed/topic/2264
+
+1.20 26 April 2011
+
+ * Bug fix, not blocking on transmit
+ by Erik Petrich, http://mbed.org/forum/bugs-suggestions/topic/2200
+
+1.19 20 April 2011
+
+ * Fixed some doxygen comment bugs.
+
+1.18 20 April 2011
+
+ * All callbacks now use MODSERIAL_callback (rather than Mbed's FunctionPointer[1] type)
+ to store and invoke it's callbacks. This allows MODSERIAL to pass a parameter
+ to callbacks. The function prototype is now void func(MODSERIAL_IRQ_INFO *q).
+ * Callbacks now pass a pointer to a MODSERIAL_IRQ_INFO class type.
+ This class holds a pointer to the MODSERIAL object that invoked the callback
+ thus freeing callbacks need to use the global variable of the original
+ MODSERIAL instance.
+ * MODSERIAL_IRQ_INFO also declares public functions that are protected within MODSERIAL
+ thus allowing certain functions to be restricted to callback context only.
+ * New function MODSERIAL_IRQ_INFO::rxDiscardLastChar() allows an rxCallback function
+ to remove the character that was just placed into the RX buffer.
+
+ [1] http://mbed.org/users/AjK/libraries/FPointer/latest/docs/
+
+1.17 08/Mar/2011
+ Fixed a memory leak in the DMA code.
+
+1.16 - 12 Feb 2011
+
+ * Missed one, doh!
+
+1.15 - 12 Feb 2011
+
+ * Fixed some typos.
+
+1.14 - 7 Feb 2011
+
+ * Fixed a bug in __putc() that caused the output buffer pointer to
+ become corrupted.
+
+1.13 - 20/01/2011
+
+ * Added extra documentation.
+ * Fixed some typos.
+
+1.12 - 20/01/2011
+
+ * Added new "autoDetectChar()" function. To use:-
+ 1st: Add a callback to invoke when the char is detected:-
+ .attach(&detectedChar, MODSERIAL::RxAutoDetect);
+ 2nd: Send the char to detect.
+ .autoDectectChar('\n');
+ Whenever that char goes into the RX buffer your callback will be invoked.
+ Added example2.cpp to demo a simple messaging system using this auto feature.
+
+
+1.11 - 23/11/2010
+
+ * Fixed a minor issue with 1.10 missed an alteration of name change.
+
+1.10 - 23/11/2010
+
+ * Rename the DMA callback from attach_dma_complete() to attach_dmaSendComplete()
+
+1.9 - 23/11/2010
+
+ * Added support for DMA sending of characters. Required is
+ the MODDMA library module:-
+ http://mbed.org/users/AjK/libraries/MODDMA/latest
+ See example_dma.cpp for more information.
+
+1.8 - 22/11/2010
+
+ * Added code so that if a buffer is set to zero length then
+ MODSERIAL defaults to just using the FIFO for that stream
+ thus making the library "fall back" to teh same operation
+ that the Mbed Serial library performs.
+ * Removed dmaSend() function that should have been removed
+ at 1.7
+
+1.7 - 21/11/2010
+
+ * Remove the DMA enum from MODSERIAL.h as it's not currently
+ ready for release.
+ * Added page doxygen comments.
+
+1.6 - 21/11/2010
+
+ * Version 1.5 solved a blocking problem on putc() when called
+ from another ISR. However, isr_tx() invokes a callback of it's
+ own when a byte is tranferred from TX buffer to TX FIFO. User
+ programs may interpret that as an IRQ callback. That's an ISR
+ call from within an existing ISR which is not good. So the
+ TxIrq callback from isr_tx is now conditional. It will only
+ be called when isr_tx() is actually within it's own ISR and
+ not when called from alternate ISR handlers.
+
+1.5 - 21/11/2010
+
+ * Calling putc() (or any derived function that uses it like
+ printf()) while inside an interrupt service routine can
+ cause the system to lock up if the TX buffer is full. This
+ is because bytes are only transferred from the TX buffer to
+ the TX FIFO via the TX ISR. If we are, say in an RX ISR already,
+ then the TX ISR will never trigger. The TX buffer stays full and
+ there is never space to putc() the byte. So, while putc() blocks
+ waiting for space it calls isr_tx() to ensure if TX FIFO space
+ becomes available it will move bytes from the TX buffer to TX
+ FIFO thus removing the blocking condition within putc().
+
+1.4 - 21/11/2010
+
+ * Removed all the new DMA code. I wish mbed.org had proper SVN
+ versioning, I'm use to working in HEAD and BRANCHES after I've
+ released a project. Getting bug reports in current releases
+ while trying to dev new code is hard to manage without source
+ control of some type!
+
+1.3 - 21/11/2010
+
+ * Fixed a macro problem with txIsBusy()
+ * Started adding code to use "block data" sending using DMA
+ * Removed #include "IOMACROS.h"
+
+1.2 - 21/11/2010
+
+ * Removed unsed variables from flushBuffer()
+ * Fixed a bug where both RX AND TX fifos are cleared/reset
+ when just TX OR RX should be cleared.
+ * Fixed a bug that cleared IIR when in fact it should be left
+ alone so that any pending interrupt after flush is handled.
+ * Merged setBase() into init() as it wasn't required anywhere else.
+ * Changed init() to enforce _uidx is set by Serial to define the _base
+ address of the Uart in use.
+
+1.1 - 20/11/2010
+
+ * Added this file
+ * Removed cruft from GETC.cpp
+ * "teh" should be "the", why do my fingers do that?
+
+1.0 - 20/11/2010
+
+ * First release.
+
+*/
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/FLUSH.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,47 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+void
+MODSERIAL::flushBuffer(IrqType type)
+{
+ uint32_t ier = _IER;
+ switch(type) {
+ case TxIrq: _IER &= ~(1UL << 1); break;
+ case RxIrq: _IER &= ~(1UL << 0); break;
+ }
+ buffer_in[type] = 0;
+ buffer_out[type] = 0;
+ buffer_count[type] = 0;
+ buffer_overflow[type] = 0;
+ switch(type) {
+ case TxIrq: _FCR = MODSERIAL_FIFO_TX_RESET; break;
+ case RxIrq: _FCR = MODSERIAL_FIFO_RX_RESET; break;
+ }
+ _IER = ier;
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/GETC.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,65 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+int
+MODSERIAL::__getc(bool block)
+{
+ // If no buffer is in use fall back to standard RX FIFO usage.
+ // Note, we must block in this case and ignore bool "block"
+ // so as to maintain compat with Mbed Serial.
+ if (buffer_size[RxIrq] == 0 || buffer[RxIrq] == (char *)NULL) {
+ while(! MODSERIAL_RBR_HAS_DATA ) ;
+ return (int)(_RBR & 0xFF);
+ }
+
+ if (block) { while ( MODSERIAL_RX_BUFFER_EMPTY ) ; } // Blocks.
+ else if ( MODSERIAL_RX_BUFFER_EMPTY ) return -1;
+
+ int c = buffer[RxIrq][buffer_out[RxIrq]];
+ buffer_out[RxIrq]++;
+ if (buffer_out[RxIrq] >= buffer_size[RxIrq]) {
+ buffer_out[RxIrq] = 0;
+ }
+
+ // If we have made space in the RX Buffer then copy over
+ // any characters in the RX FIFO that my reside there.
+ // Temporarily disable the RX IRQ so that we do not re-enter
+ // it under interrupts.
+ if ( ! MODSERIAL_RX_BUFFER_FULL ) {
+ uint32_t ier = _IER;
+ _IER &= ~(1UL << 0);
+ isr_rx();
+ _IER = ier;
+ }
+
+ __disable_irq();
+ buffer_count[RxIrq]--;
+ __enable_irq();
+ return c;
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/INIT.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,80 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+void
+MODSERIAL::init( int txSize, int rxSize )
+{
+ disableIrq();
+
+ callbackInfo.setSerial(this);
+
+#ifdef __LPC11UXX_H__
+
+ _base = LPC_USART;
+
+#else
+ switch(_uidx) {
+ case 0: _base = LPC_UART0; break;
+ case 1: _base = LPC_UART1; break;
+ case 2: _base = LPC_UART2; break;
+ case 3: _base = LPC_UART3; break;
+ default : _base = NULL; break;
+ }
+#endif
+
+ dmaSendChannel = -1;
+ moddma_p = (void *)NULL;
+
+ if (_base != NULL) {
+ buffer_size[RxIrq] = rxSize;
+ buffer[RxIrq] = rxSize > 0 ? (char *)malloc(buffer_size[RxIrq]) : (char *)NULL;
+ buffer_in[RxIrq] = 0;
+ buffer_out[RxIrq] = 0;
+ buffer_count[RxIrq] = 0;
+ buffer_overflow[RxIrq] = 0;
+ Serial::attach(this, &MODSERIAL::isr_rx, Serial::RxIrq);
+
+ buffer_size[TxIrq] = txSize;
+ buffer[TxIrq] = txSize > 0 ? (char *)malloc(buffer_size[TxIrq]) : (char *)NULL;
+ buffer_in[TxIrq] = 0;
+ buffer_out[TxIrq] = 0;
+ buffer_count[TxIrq] = 0;
+ buffer_overflow[TxIrq] = 0;
+ Serial::attach(this, &MODSERIAL::isr_tx, Serial::TxIrq);
+ }
+ else {
+ error("MODSERIAL must have a defined UART to function.");
+ }
+
+ _FCR = MODSERIAL_FIFO_ENABLE | MODSERIAL_FIFO_RX_RESET | MODSERIAL_FIFO_TX_RESET;
+
+ auto_detect_char = 0;
+
+ enableIrq();
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/ISR_RX.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,60 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+void
+MODSERIAL::isr_rx(void)
+{
+ if (! _base || buffer_size[RxIrq] == 0 || buffer[RxIrq] == (char *)NULL) {
+ _isr[RxIrq].call(&this->callbackInfo);
+ return;
+ }
+
+ while( MODSERIAL_RBR_HAS_DATA ) {
+ rxc = (char)(_RBR & 0xFF);
+ if ( MODSERIAL_RX_BUFFER_FULL ) {
+ buffer_overflow[RxIrq] = rxc; // Oh dear, no room in buffer.
+ _isr[RxOvIrq].call(&this->callbackInfo);
+ }
+ else {
+ if (buffer[RxIrq] != (char *)NULL) {
+ buffer[RxIrq][buffer_in[RxIrq]] = rxc;
+ buffer_count[RxIrq]++;
+ buffer_in[RxIrq]++;
+ if (buffer_in[RxIrq] >= buffer_size[RxIrq]) {
+ buffer_in[RxIrq] = 0;
+ }
+ }
+ _isr[RxIrq].call(&this->callbackInfo);
+ }
+ if (auto_detect_char == rxc) {
+ _isr[RxAutoDetect].call(&this->callbackInfo);
+ }
+ }
+}
+
+}; // namespace AjK ends
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/ISR_TX.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,54 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+void
+MODSERIAL::isr_tx(bool doCallback)
+{
+ if (! _base || buffer_size[TxIrq] == 0 || buffer[TxIrq] == (char *)NULL) {
+ _isr[TxIrq].call(&this->callbackInfo);
+ return;
+ }
+
+ while (! MODSERIAL_TX_BUFFER_EMPTY && MODSERIAL_THR_HAS_SPACE ) {
+ _THR = txc = (uint8_t)(buffer[TxIrq][buffer_out[TxIrq]]);
+ buffer_count[TxIrq]--;
+ buffer_out[TxIrq]++;
+ if (buffer_out[TxIrq] >= buffer_size[TxIrq]) {
+ buffer_out[TxIrq] = 0;
+ }
+ if (doCallback) _isr[TxIrq].call(&this->callbackInfo);
+ }
+
+ if ( MODSERIAL_TX_BUFFER_EMPTY ) {
+ _IER = 1;
+ _isr[TxEmpty].call(&this->callbackInfo);
+ }
+}
+
+}; // namespace AjK ends
+
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/MODSERIAL/MACROS.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,70 @@ +/* + Copyright (c) 2010 Andy Kirkham + + Permission is hereby granted, free of charge, to any person obtaining a copy + of this software and associated documentation files (the "Software"), to deal + in the Software without restriction, including without limitation the rights + to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + copies of the Software, and to permit persons to whom the Software is + furnished to do so, subject to the following conditions: + + The above copyright notice and this permission notice shall be included in + all copies or substantial portions of the Software. + + THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + THE SOFTWARE. +*/ + +#ifndef MODSERIAL_MACROS_H +#define MODSERIAL_MACROS_H + +#define MODSERIAL_RBR 0x00 +#define MODSERIAL_THR 0x00 +#define MODSERIAL_DLL 0x00 +#define MODSERIAL_IER 0x04 +#define MODSERIAL_DML 0x04 +#define MODSERIAL_IIR 0x08 +#define MODSERIAL_FCR 0x08 +#define MODSERIAL_LCR 0x0C +#define MODSERIAL_LSR 0x14 +#define MODSERIAL_SCR 0x1C +#define MODSERIAL_ACR 0x20 +#define MODSERIAL_ICR 0x24 +#define MODSERIAL_FDR 0x28 +#define MODSERIAL_TER 0x30 + +#define MODSERIAL_LSR_RDR (1UL << 0) +#define MODSERIAL_LSR_OE (1UL << 1) +#define MODSERIAL_LSR_PE (1UL << 2) +#define MODSERIAL_LSR_FE (1UL << 3) +#define MODSERIAL_LSR_BR (1UL << 4) +#define MODSERIAL_LSR_THRE (1UL << 5) +#define MODSERIAL_LSR_TEMT (1UL << 6) +#define MODSERIAL_LSR_RXFE (1UL << 7) + +#define MODSERIAL_FIFO_ENABLE 1 +#define MODSERIAL_FIFO_RX_RESET 2 +#define MODSERIAL_FIFO_TX_RESET 4 + +#define _RBR *((char *)_base+MODSERIAL_RBR) +#define _THR *((char *)_base+MODSERIAL_THR) +#define _IIR *((char *)_base+MODSERIAL_IIR) +#define _IER *((char *)_base+MODSERIAL_IER) +#define _LSR *((char *)_base+MODSERIAL_LSR) +#define _FCR *((char *)_base+MODSERIAL_FCR) + +#define MODSERIAL_TX_BUFFER_EMPTY (buffer_count[TxIrq]==0) +#define MODSERIAL_RX_BUFFER_EMPTY (buffer_count[RxIrq]==0) +#define MODSERIAL_TX_BUFFER_FULL (buffer_count[TxIrq]==buffer_size[TxIrq]) +#define MODSERIAL_RX_BUFFER_FULL (buffer_count[RxIrq]==buffer_size[RxIrq]) + +#define MODSERIAL_THR_HAS_SPACE ((int)_LSR&MODSERIAL_LSR_THRE) +#define MODSERIAL_TEMT_IS_EMPTY ((int)_LSR&MODSERIAL_LSR_TEMT) +#define MODSERIAL_RBR_HAS_DATA ((int)_LSR&MODSERIAL_LSR_RDR) + +#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/MODSERIAL.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,137 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file MODSERIAL.h
+ @purpose Extends Serial to provide fully buffered IO
+ @version 1.6
+ @date Nov 2010
+ @author Andy Kirkham
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+MODSERIAL::MODSERIAL( PinName tx, PinName rx, const char *name ) : Serial( tx, rx, name )
+{
+ init( MODSERIAL_DEFAULT_TX_BUFFER_SIZE, MODSERIAL_DEFAULT_RX_BUFFER_SIZE );
+}
+
+MODSERIAL::MODSERIAL( PinName tx, PinName rx, int bufferSize, const char *name ) : Serial( tx, rx, name )
+{
+ init( bufferSize, bufferSize );
+}
+
+MODSERIAL::MODSERIAL( PinName tx, PinName rx, int txSize, int rxSize, const char *name ) : Serial( tx, rx, name )
+{
+ init( txSize, rxSize );
+}
+
+MODSERIAL::~MODSERIAL()
+{
+ disableIrq();
+ if ( buffer[0] != NULL) free((char *)buffer[0] );
+ if ( buffer[1] != NULL) free((char *)buffer[1] );
+}
+
+bool
+MODSERIAL::txBufferFull( void )
+{
+ return MODSERIAL_TX_BUFFER_FULL;
+}
+
+bool
+MODSERIAL::rxBufferFull( void )
+{
+ return MODSERIAL_RX_BUFFER_FULL;
+}
+
+bool
+MODSERIAL::txBufferEmpty( void )
+{
+ return MODSERIAL_TX_BUFFER_EMPTY;
+}
+
+bool
+MODSERIAL::rxBufferEmpty( void )
+{
+ return MODSERIAL_RX_BUFFER_EMPTY;
+}
+
+bool
+MODSERIAL::txIsBusy( void )
+{
+ return ( _LSR & ( 3UL << 5 ) == 0 ) ? true : false;
+}
+
+void
+MODSERIAL::disableIrq( void )
+{
+
+#ifdef __LPC11UXX_H__
+ NVIC_DisableIRQ( UART_IRQn );
+#else
+ switch(_uidx) {
+ case 0: NVIC_DisableIRQ( UART0_IRQn ); break;
+ case 1: NVIC_DisableIRQ( UART1_IRQn ); break;
+ case 2: NVIC_DisableIRQ( UART2_IRQn ); break;
+ case 3: NVIC_DisableIRQ( UART3_IRQn ); break;
+ }
+#endif
+}
+
+void
+MODSERIAL::enableIrq(void)
+{
+#ifdef __LPC11UXX_H__
+ NVIC_EnableIRQ( UART_IRQn );
+#else
+ switch( _uidx ) {
+ case 0: NVIC_EnableIRQ( UART0_IRQn ); break;
+ case 1: NVIC_EnableIRQ( UART1_IRQn ); break;
+ case 2: NVIC_EnableIRQ( UART2_IRQn ); break;
+ case 3: NVIC_EnableIRQ( UART3_IRQn ); break;
+ }
+#endif
+}
+
+int
+MODSERIAL::rxDiscardLastChar( void )
+{
+ // This function can only be called indirectly from
+ // an rxCallback function. Therefore, we know we
+ // just placed a char into the buffer.
+ char c = buffer[RxIrq][buffer_in[RxIrq]];
+
+ if (buffer_count[RxIrq]) {
+ buffer_count[RxIrq]--;
+ buffer_in[RxIrq]--;
+ if (buffer_in[RxIrq] < 0) {
+ buffer_in[RxIrq] = buffer_size[RxIrq] - 1;
+ }
+ }
+
+ return (int)c;
+}
+
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/MODSERIAL.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,1091 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file MODSERIAL.h
+ @purpose Extends Serial to provide fully buffered IO
+ @version see ChangeLog.c
+ @date Nov 2010
+ @author Andy Kirkham
+*/
+
+#ifndef MODSERIAL_H
+#define MODSERIAL_H
+
+/** @defgroup API The MODSERIAL API */
+/** @defgroup MISC Misc MODSERIAL functions */
+/** @defgroup INTERNALS MODSERIAL Internals */
+
+#ifndef MODSERIAL_DEFAULT_RX_BUFFER_SIZE
+#define MODSERIAL_DEFAULT_RX_BUFFER_SIZE 256
+#endif
+
+#ifndef MODSERIAL_DEFAULT_TX_BUFFER_SIZE
+#define MODSERIAL_DEFAULT_TX_BUFFER_SIZE 256
+#endif
+
+#include "mbed.h"
+
+namespace AjK {
+
+// Forward reference.
+class MODSERIAL;
+
+/**
+ * @author Andy Kirkham
+ * @see http://mbed.org/cookbook/MODSERIAL
+ * @see example3a.cpp
+ * @see example3b.cpp
+ * @see API
+ *
+ * <b>MODSERIAL_IRQ_INFO</b> is a class used to pass information (and access to protected
+ * MODSERIAL functions) to IRQ callbacks.
+ */
+class MODSERIAL_IRQ_INFO
+{
+public:
+ friend class MODSERIAL;
+
+ MODSERIAL *serial;
+
+ MODSERIAL_IRQ_INFO() { serial = 0; }
+
+ /** rxDiscardLastChar()
+ *
+ * Remove the last char placed into the rx buffer.
+ * This is an operation that can only be performed
+ * by an rxCallback function.
+ * @ingroup API
+ * @return The byte removed from the buffer.
+ */
+ int rxDiscardLastChar(void);
+
+protected:
+
+ /** setSerial()
+ *
+ * Used internally by MODSERIAL to set the "this" pointer
+ * of the MODSERIAL that created this object.
+ * @ingroup INTERNAL
+ * @param A pointer to a MODSERIAL object instance.
+ */
+ void setSerial(MODSERIAL *s) { serial = s; }
+};
+
+// Forward reference dummy class.
+class MODSERIAL_callback_dummy;
+
+/**
+ * @author Andy Kirkham
+ * @see http://mbed.org/cookbook/MODSERIAL
+ * @see example3a.cpp
+ * @see example3b.cpp
+ * @see API
+ *
+ * <b>MODSERIAL_callback</b> is a class used to hold application callbacks that
+ * MODSERIAL can invoke on certain events.
+ */
+class MODSERIAL_callback
+{
+protected:
+
+ //! C callback function pointer.
+ void (*c_callback)(MODSERIAL_IRQ_INFO *);
+
+ //! C++ callback object/method pointer (the object part).
+ MODSERIAL_callback_dummy *obj_callback;
+
+ //! C++ callback object/method pointer (the method part).
+ void (MODSERIAL_callback_dummy::*method_callback)(MODSERIAL_IRQ_INFO *);
+
+public:
+
+ /** Constructor
+ */
+ MODSERIAL_callback() {
+ c_callback = 0;
+ obj_callback = 0;
+ method_callback = 0;
+ }
+
+ /** attach - Overloaded attachment function.
+ *
+ * Attach a C type function pointer as the callback.
+ *
+ * Note, the callback function prototype must be:-
+ * @code
+ * void myCallbackFunction(MODSERIAL_IRQ_INFO *);
+ * @endcode
+ * @param A C function pointer to call.
+ */
+ void attach(void (*function)(MODSERIAL_IRQ_INFO *) = 0) { c_callback = function; }
+
+ /** attach - Overloaded attachment function.
+ *
+ * Attach a C++ type object/method pointer as the callback.
+ *
+ * Note, the callback method prototype must be:-
+ * @code
+ * public:
+ * void myCallbackFunction(MODSERIAL_IRQ_INFO *);
+ * @endcode
+ * @param A C++ object pointer.
+ * @param A C++ method within the object to call.
+ */
+ template<class T>
+ void attach(T* item, void (T::*method)(MODSERIAL_IRQ_INFO *)) {
+ obj_callback = (MODSERIAL_callback_dummy *)item;
+ method_callback = (void (MODSERIAL_callback_dummy::*)(MODSERIAL_IRQ_INFO *))method;
+ }
+
+ /** call - Overloaded callback initiator.
+ *
+ * call the callback function.
+ *
+ * @param A pointer to a MODSERIAL_IRQ_INFO object.
+ */
+ void call(MODSERIAL_IRQ_INFO *arg) {
+ if (c_callback != 0) {
+ (*c_callback)(arg);
+ }
+ else {
+ if (obj_callback != 0 && method_callback != 0) {
+ (obj_callback->*method_callback)(arg);
+ }
+ }
+ }
+};
+
+/**
+ * @author Andy Kirkham
+ * @see http://mbed.org/cookbook/MODSERIAL
+ * @see http://mbed.org/handbook/Serial
+ * @see example1.cpp
+ * @see example2.cpp
+ * @see example3a.cpp
+ * @see example3b.cpp
+ * @see example_dma.cpp
+ * @see API
+ *
+ * <b>MODSERIAL</b> extends the Mbed library <a href="/handbook/Serial">Serial</a> to provide fully buffered
+ * TX and RX streams. Buffer length is fully customisable.
+ *
+ * Before using MODSERIAL users should be familar with Mbed's standard <a href="/handbook/Serial">Serial</a>
+ * library object. MODSERIAL is a direct "drop in" replacement for <a href="/handbook/Serial">Serial</a>. Where
+ * previously Serial was used, MODSERIAL can be used as adirect replacement instantly offering standard
+ * TX and RX buffering. By default, both TX and RX buffers are 256 bytes in length.
+ *
+ * @image html /media/uploads/mbedofficial/serial_interfaces.png
+ *
+ * Standard example:
+ * @code
+ * #include "mbed.h"
+ * #include "MODSERIAL.h"
+ *
+ * MODSERIAL pc(USBTX, USBRX); // tx, rx
+ *
+ * int main() {
+ * pc.printf("Hello World!");
+ * while(1) {
+ * pc.putc(pc.getc() + 1);
+ * }
+ * }
+ * @endcode
+ *
+ * Example with alternate buffer length:
+ * @code
+ * #include "mbed.h"
+ * #include "MODSERIAL.h"
+ *
+ * // Make TX and RX buffers 512byes in length
+ * MODSERIAL pc(USBTX, USBRX, 512); // tx, rx
+ *
+ * int main() {
+ * pc.printf("Hello World!");
+ * while(1) {
+ * pc.putc(pc.getc() + 1);
+ * }
+ * }
+ * @endcode
+ *
+ * Example with alternate buffer length:
+ * @code
+ * #include "mbed.h"
+ * #include "MODSERIAL.h"
+ *
+ * // Make TX 1024bytes and RX 512byes in length
+ * MODSERIAL pc(USBTX, USBRX, 1024, 512); // tx, rx
+ *
+ * int main() {
+ * pc.printf("Hello World!");
+ * while(1) {
+ * pc.putc(pc.getc() + 1);
+ * }
+ * }
+ * @endcode
+ */
+class MODSERIAL : public Serial
+{
+public:
+
+ // Allow instances of MODSERIAL_IRQ_INFO to use protected properties and methods.
+ friend class MODSERIAL_IRQ_INFO;
+
+ //! A copy of the Serial parity enum
+ /** @see http://mbed.org/projects/libraries/api/mbed/trunk/Serial#Serial.format */
+ enum Parity {
+ None = 0
+ , Odd
+ , Even
+ , Forced1
+ , Forced0
+ };
+
+ //! A copy of the Serial IrqType enum
+ enum IrqType {
+ RxIrq = 0
+ , TxIrq
+ , RxOvIrq
+ , TxOvIrq
+ , TxEmpty
+ , RxAutoDetect
+ , NumOfIrqTypes
+ };
+
+ //! Non-blocking functions return code.
+ enum Result {
+ Ok = 0 /*!< Ok. */
+ , NoMemory = -1 /*!< Memory allocation failed. */
+ , NoChar = -1 /*!< No character in buffer. */
+ , BufferOversize = -2 /*!< Oversized buffer. */
+ };
+
+ /**
+ * The MODSERIAL constructor is used to initialise the serial object.
+ *
+ * @param tx PinName of the TX pin.
+ * @param rx PinName of the TX pin.
+ * @param name An option name for RPC usage.
+ */
+ MODSERIAL(PinName tx, PinName rx, const char *name = NULL);
+
+ /**
+ * The MODSERIAL constructor is used to initialise the serial object.
+ *
+ * @param tx PinName of the TX pin.
+ * @param rx PinName of the TX pin.
+ * @param bufferSize Integer of the TX and RX buffer sizes.
+ * @param name An option name for RPC usage.
+ */
+ MODSERIAL(PinName tx, PinName rx, int bufferSize, const char *name = NULL);
+
+ /**
+ * The MODSERIAL constructor is used to initialise the serial object.
+ *
+ * @param tx PinName of the TX pin.
+ * @param rx PinName of the TX pin.
+ * @param txBufferSize Integer of the TX buffer sizes.
+ * @param rxBufferSize Integer of the RX buffer sizes.
+ * @param name An option name for RPC usage.
+ */
+ MODSERIAL(PinName tx, PinName rx, int txBufferSize, int rxBufferSize, const char *name = NULL);
+
+ virtual ~MODSERIAL();
+
+ /**
+ * Function: attach
+ *
+ * The Mbed standard <a href="/handbook/Serial">Serial</a> library object allows an interrupt callback
+ * to be made when a byte is received by the TX or RX UART hardware. MODSERIAL traps these interrupts
+ * to enable it's buffering system. However, after the byte has been received/sent under interrupt control,
+ * MODSERIAL can callback a user function as a notification of the interrupt. Note, user code should not
+ * directly interact with the Uart hardware, MODSERIAL does that, instead, MODSERIAL API functions should
+ * be used.
+ *
+ * <b>Note</b>, a character is written out then, if there is room in the TX FIFO and the TX buffer is empty,
+ * putc() will put the character directly into THR (the output holding register). If the TX FIFO is full and
+ * cannot accept the character, it is placed into the TX output buffer. The TX interrupts are then enabled
+ * so that when the TX FIFO empties, the TX buffer is then transferred to the THR FIFO. The TxIrq will ONLY
+ * be activated when this transfer of a character from BUFFER to THR FIFO takes place. If your character
+ * throughput is not high bandwidth, then the 16 byte TX FIFO may be enough and the TX output buffer may
+ * never come into play.
+ *
+ * @code
+ * #include "mbed.h"
+ * #include "MODSERIAL.h"
+ *
+ * DigitalOut led1(LED1);
+ * DigitalOut led2(LED2);
+ * DigitalOut led3(LED3);
+ *
+ * // To test, connect p9 to p10 as a loopback.
+ * MODSERIAL pc(p9, p10);
+ *
+ * // This function is called when a character goes into the TX buffer.
+ * void txCallback(void) {
+ * led2 = !led2;
+ * }
+ *
+ * // This function is called when a character goes into the RX buffer.
+ * void rxCallback(void) {
+ * led3 = !led3;
+ * }
+ *
+ * int main() {
+ * pc.baud(115200);
+ * pc.attach(&txCallback, MODSERIAL::TxIrq);
+ * pc.attach(&rxCallback, MODSERIAL::RxIrq);
+ *
+ * while(1) {
+ * led1 = !led1;
+ * wait(0.5);
+ * pc.putc('A');
+ * wait(0.5);
+ * }
+ * ]
+ * @endcode
+ *
+ * @ingroup API
+ * @param fptr A pointer to a void function, or 0 to set as none
+ * @param type Which serial interrupt to attach the member function to (Seriall::RxIrq for receive, TxIrq for transmit buffer empty)
+ */
+ void attach(void (*fptr)(MODSERIAL_IRQ_INFO *), IrqType type = RxIrq) { _isr[type].attach(fptr); }
+
+ /**
+ * Function: attach
+ *
+ * The Mbed standard <a href="/handbook/Serial">Serial</a> library object allows an interrupt callback
+ * to be made when a byte is received by the TX or RX UART hardware. MODSERIAL traps these interrupts
+ * to enable it's buffering system. However, after the byte has been received/sent under interrupt control,
+ * MODSERIAL can callback a user function as a notification of the interrupt. Note, user code should not
+ * directly interact with the Uart hardware, MODSERIAL does that, instead, MODSERIAL API functions should
+ * be used.
+ *
+ * <b>Note</b>, a character is written out then, if there is room in the TX FIFO and the TX buffer is empty,
+ * putc() will put the character directly into THR (the output holding register). If the TX FIFO is full and
+ * cannot accept the character, it is placed into the TX output buffer. The TX interrupts are then enabled
+ * so that when the TX FIFO empties, the TX buffer is then transferred to the THR FIFO. The TxIrq will ONLY
+ * be activated when this transfer of a character from BUFFER to THR FIFO takes place. If your character
+ * throughput is not high bandwidth, then the 16 byte TX FIFO may be enough and the TX output buffer may
+ * never come into play.
+ *
+ * @code
+ * #include "mbed.h"
+ * #include "MODSERIAL.h"
+ *
+ * DigitalOut led1(LED1);
+ * DigitalOut led2(LED2);
+ * DigitalOut led3(LED3);
+ *
+ * // To test, connect p9 to p10 as a loopback.
+ * MODSERIAL pc(p9, p10);
+ *
+ * class Foo {
+ * public:
+ * // This method is called when a character goes into the TX buffer.
+ * void txCallback(void) { led2 = !led2; }
+ *
+ * // This method is called when a character goes into the RX buffer.
+ * void rxCallback(void) { led3 = !led3; }
+ * };
+ *
+ * Foo foo;
+ *
+ * int main() {
+ * pc.baud(115200);
+ * pc.attach(&foo, &Foo::txCallback, MODSERIAL::TxIrq);
+ * pc.attach(&foo, &Foo::rxCallback, MODSERIAL::RxIrq);
+ *
+ * while(1) {
+ * led1 = !led1;
+ * wait(0.5);
+ * pc.putc('A');
+ * wait(0.5);
+ * }
+ * ]
+ * @endcode
+ *
+ * @ingroup API
+ * @param tptr A pointer to the object to call the member function on
+ * @param mptr A pointer to the member function to be called
+ * @param type Which serial interrupt to attach the member function to (Seriall::RxIrq for receive, TxIrq for transmit buffer empty)
+ */
+ template<typename T>
+ void attach(T* tptr, void (T::*mptr)(MODSERIAL_IRQ_INFO *), IrqType type = RxIrq) {
+ if((mptr != 0) && (tptr != 0)) {
+ _isr[type].attach(tptr, mptr);
+ }
+ }
+
+ /**
+ * @see attach
+ * @ingroup API
+ */
+ void connect(void (*fptr)(MODSERIAL_IRQ_INFO *), IrqType type = RxIrq) { _isr[RxIrq].attach(fptr); }
+
+ /**
+ * @see attach
+ * @ingroup API
+ */
+ template<typename T>
+ void connect(T* tptr, void (T::*mptr)(MODSERIAL_IRQ_INFO *), IrqType type = RxIrq) {
+ if((mptr != 0) && (tptr != 0)) {
+ _isr[type].attach(tptr, mptr);
+ }
+ }
+
+ /**
+ * Function: writeable
+ *
+ * Determine if there is space available to write a byte
+ *
+ * @ingroup API
+ * @return 1 if there is space to write a character, else 0
+ */
+ int writeable() { return txBufferFull() ? 0 : 1; }
+
+ /**
+ * Function: readable
+ *
+ * Determine if there is a byte available to read
+ *
+ * @ingroup API
+ * @return 1 if there is a character available to read, else 0
+ */
+ int readable() { return rxBufferEmpty() ? 0 : 1; }
+
+ /**
+ * Function: txBufferSane
+ *
+ * Determine if the TX buffer has been initialized.
+ *
+ * @ingroup API
+ * @return true if the buffer is initialized, else false
+ */
+ bool txBufferSane(void) { return buffer[TxIrq] != (char *)NULL ? true : false; }
+
+ /**
+ * Function: rxBufferSane
+ *
+ * Determine if the RX buffer has been initialized.
+ *
+ * @ingroup API
+ * @return true if the buffer is initialized, else false
+ */
+ bool rxBufferSane(void) { return buffer[TxIrq] != (char *)NULL ? true : false; }
+
+ /**
+ * Function: txBufferGetCount
+ *
+ * Returns how many bytes are in the TX buffer
+ *
+ * @ingroup API
+ * @return The number of bytes in the TX buffer
+ */
+ int txBufferGetCount(void) { return buffer_count[TxIrq]; }
+
+ /**
+ * Function: rxBufferGetCount
+ *
+ * Returns how many bytes are in the RX buffer
+ *
+ * @ingroup API
+ * @return The number of bytes in the RX buffer
+ */
+ int rxBufferGetCount(void) { return buffer_count[RxIrq]; }
+
+ /**
+ * Function: txBufferGetSize
+ *
+ * Returns the current size of the TX buffer
+ *
+ * @ingroup API
+ * @return The length iof the TX buffer in bytes
+ */
+ int txBufferGetSize(int size) { return buffer_size[TxIrq]; }
+
+ /**
+ * Function: rxBufferGetSize
+ *
+ * Returns the current size of the RX buffer
+ *
+ * @ingroup API
+ * @return The length iof the RX buffer in bytes
+ */
+ int rxBufferGetSize(int size) { return buffer_size[RxIrq]; }
+
+ /**
+ * Function: txBufferFull
+ *
+ * Is the TX buffer full?
+ *
+ * @ingroup API
+ * @return true if the TX buffer is full, otherwise false
+ */
+ bool txBufferFull(void);
+
+ /**
+ * Function: rxBufferFull
+ *
+ * Is the RX buffer full?
+ *
+ * @ingroup API
+ * @return true if the RX buffer is full, otherwise false
+ */
+ bool rxBufferFull(void);
+
+ /**
+ * Function: txBufferEmpty
+ *
+ * Is the TX buffer empty?
+ *
+ * @ingroup API
+ * @return true if the TX buffer is empty, otherwise false
+ */
+ bool txBufferEmpty(void);
+
+ /**
+ * Function: rxBufferEmpty
+ *
+ * Is the RX buffer empty?
+ *
+ * @ingroup API
+ * @return true if the RX buffer is empty, otherwise false
+ */
+ bool rxBufferEmpty(void);
+
+ /**
+ * Function: txBufferSetSize
+ *
+ * Change the TX buffer size.
+ *
+ * @see Result
+ * @ingroup API
+ * @param size The new TX buffer size in bytes.
+ * @param m Perform a memory sanity check. Errs the Mbed if memory alloc fails.
+ * @return Result Ok on success.
+ */
+ int txBufferSetSize(int size, bool m) { return resizeBuffer(size, TxIrq, m); }
+
+ /**
+ * Function: rxBufferSetSize
+ *
+ * Change the RX buffer size.
+ *
+ * @see Result
+ * @ingroup API
+ * @param size The new RX buffer size in bytes.
+ * @param m Perform a memory sanity check. Errs the Mbed if memory alloc fails.
+ * @return Result Ok on success.
+ */
+ int rxBufferSetSize(int size, bool m) { return resizeBuffer(size, RxIrq, m); }
+
+ /**
+ * Function: txBufferSetSize
+ *
+ * Change the TX buffer size.
+ * Always performs a memory sanity check, halting the Mbed on failure.
+ *
+ * @see Result
+ * @ingroup API
+ * @param size The new TX buffer size in bytes.
+ * @return Result Ok on success.
+ */
+ int txBufferSetSize(int size) { return resizeBuffer(size, TxIrq, true); }
+
+ /**
+ * Function: rxBufferSetSize
+ *
+ * Change the RX buffer size.
+ * Always performs a memory sanity check, halting the Mbed on failure.
+ *
+ * @see Result
+ * @ingroup API
+ * @param size The new RX buffer size in bytes.
+ * @return Result Ok on success.
+ */
+ int rxBufferSetSize(int size) { return resizeBuffer(size, RxIrq, true); }
+
+ /**
+ * Function: txBufferFlush
+ *
+ * Remove all bytes from the TX buffer.
+ * @ingroup API
+ */
+ void txBufferFlush(void) { flushBuffer(TxIrq); }
+
+ /**
+ * Function: rxBufferFlush
+ *
+ * Remove all bytes from the RX buffer.
+ * @ingroup API
+ */
+ void rxBufferFlush(void) { flushBuffer(RxIrq); }
+
+ /**
+ * Function: getcNb
+ *
+ * Like getc() but is non-blocking. If no bytes are in the RX buffer this
+ * function returns Result::NoChar (-1)
+ *
+ * @ingroup API
+ * @return A byte from the RX buffer or Result::NoChar (-1) if bufer empty.
+ */
+ int getcNb() { return __getc(false); }
+
+ /**
+ * Function: getc
+ *
+ * Overloaded version of Serial::getc()
+ *
+ * This function blocks (if the RX buffer is empty the function will wait for a
+ * character to arrive and then return that character).
+ *
+ * @ingroup API
+ * @return A byte from the RX buffer
+ */
+ int getc() { return __getc(true); }
+
+ /**
+ * Function: txGetLastChar
+ *
+ * Rteurn the last byte to pass through the TX interrupt handler.
+ *
+ * @ingroup MISC
+ * @return The byte
+ */
+ char txGetLastChar(void) { return txc; }
+
+ /**
+ * Function: rxGetLastChar
+ *
+ * Return the last byte to pass through the RX interrupt handler.
+ *
+ * @ingroup MISC
+ * @return The byte
+ */
+ char rxGetLastChar(void) { return rxc; }
+
+ /**
+ * Function: txIsBusy
+ *
+ * If the Uart is still actively sending characters this
+ * function will return true.
+ *
+ * @ingroup API
+ * @return bool
+ */
+ bool txIsBusy(void);
+
+ /**
+ * Function: autoDetectChar
+ *
+ * Set the char that, if seen incoming, invokes the AutoDetectChar callback.
+ *
+ * @ingroup API
+ * @param int c The character to detect.
+ */
+ void autoDetectChar(char c) { auto_detect_char = c; }
+
+ /**
+ * Function: move
+ *
+ * Move contents of RX buffer to external buffer. Stops if "end" detected.
+ *
+ * @ingroup API
+ * @param char *s The destination buffer address
+ * @param int max The maximum number of chars to move.
+ * @param char end If this char is detected stop moving.
+ */
+ int move(char *s, int max, char end) {
+ int counter = 0;
+ char c;
+ while(readable()) {
+ c = getc();
+ if (c == end) break;
+ *(s++) = c;
+ counter++;
+ if (counter == max) break;
+ }
+ return counter;
+ }
+
+ /**
+ * Function: move (overloaded)
+ *
+ * Move contents of RX buffer to external buffer. Stops if auto_detect_char detected.
+ *
+ * @ingroup API
+ * @param int max The maximum number of chars to move.
+ * @param char *s The destination buffer address
+ */
+ int move(char *s, int max) {
+ return move(s, max, auto_detect_char);
+ }
+
+ #if 0 // Inhereted from Serial/Stream, for documentation only
+ /**
+ * Function: putc
+ *
+ * Write a character
+ * Inhereted from Serial/Stream
+ *
+ * @see http://mbed.org/projects/libraries/api/mbed/trunk/Serial#Serial.putc
+ * @ingroup API
+ * @param c The character to write to the serial port
+ */
+ int putc(int c);
+ #endif
+
+ #if 0 // Inhereted from Serial/Stream, for documentation only
+ /**
+ * Function: printf
+ *
+ * Write a formated string
+ * Inhereted from Serial/Stream
+ *
+ * @see http://mbed.org/projects/libraries/api/mbed/trunk/Serial#Serial.printf
+ * @ingroup API
+ * @param format A printf-style format string, followed by the variables to use in formating the string.
+ */
+ int printf(const char* format, ...);
+ #endif
+
+ #if 0 // Inhereted from Serial/Stream, for documentation only
+ /**
+ * Function: scanf
+ *
+ * Read a formated string
+ * Inhereted from Serial/Stream
+ *
+ * @see http://mbed.org/projects/libraries/api/mbed/trunk/Serial#Serial.scanf
+ * @ingroup API
+ * @param format - A scanf-style format string, followed by the pointers to variables to store the results.
+ */
+ int scanf(const char* format, ...);
+ #endif
+
+protected:
+ /**
+ * Used to pass information to callbacks.
+ * @ingroup INTERNALS
+ */
+ MODSERIAL_IRQ_INFO callbackInfo;
+
+ /**
+ * Remove the last char placed into the rx buffer.
+ * This is an operation that can only be performed
+ * by an rxCallback function. To protect the buffers
+ * this function is defined protected so that a
+ * regular application cannot call it directly. It
+ * can only be called by the public version within a
+ * MODSERIAL_IRQ_INFO class.
+ * @ingroup INTERNALS
+ * @return The byte removed from the buffer.
+ */
+ int rxDiscardLastChar(void);
+
+private:
+
+ /**
+ * A pointer to the UART peripheral base address being used.
+ * @ingroup INTERNALS
+ */
+ void *_base;
+
+ /**
+ * The last byte to pass through the TX IRQ handler.
+ * @ingroup INTERNALS
+ */
+ volatile char txc;
+
+ /**
+ * The last byte to pass through the RX IRQ handler.
+ * @ingroup INTERNALS
+ */
+ volatile char rxc;
+
+ /**
+ * Pointers to the TX and RX buffers.
+ * @ingroup INTERNALS
+ */
+ volatile char *buffer[2];
+
+ /**
+ * Buffer in pointers.
+ * @ingroup INTERNALS
+ */
+ volatile int buffer_in[2];
+
+ /**
+ * Buffer out pointers.
+ * @ingroup INTERNALS
+ */
+ volatile int buffer_out[2];
+
+ /**
+ * Buffer lengths.
+ * @ingroup INTERNALS
+ */
+ volatile int buffer_size[2];
+
+ /**
+ * Buffer content counters.
+ * @ingroup INTERNALS
+ */
+ volatile int buffer_count[2];
+
+ /**
+ * Buffer overflow.
+ * @ingroup INTERNALS
+ */
+ volatile int buffer_overflow[2];
+
+ /**
+ * Auto-detect character.
+ * @ingroup INTERNALS
+ */
+ volatile char auto_detect_char;
+
+ /**
+ * Callback system.
+ * @ingroup INTERNALS
+ */
+ MODSERIAL_callback _isr[NumOfIrqTypes];
+
+ /**
+ * TX Interrupt Service Routine.
+ * @ingroup INTERNALS
+ */
+ void isr_tx(bool doCallback);
+
+ /**
+ * TX Interrupt Service Routine stub version.
+ * @ingroup INTERNALS
+ */
+ void isr_tx(void) { isr_tx(true); }
+
+
+ /**
+ * RX Interrupt Service Routine.
+ * @ingroup INTERNALS
+ */
+ void isr_rx(void);
+
+ /**
+ * Disable the interrupts for this Uart.
+ * @ingroup INTERNALS
+ */
+ void disableIrq(void);
+
+ /**
+ * Enable the interrupts for this Uart.
+ * @ingroup INTERNALS
+ */
+ void enableIrq(void);
+
+ /**
+ * Get a character from the RX buffer
+ * @ingroup INTERNALS
+ * @param bool True to block (wait for input)
+ * @return A byte from the buffer.
+ */
+ int __getc(bool);
+
+ /**
+ * Put a character from the TX buffer
+ * @ingroup INTERNALS
+ * @param bool True to block (wait for space in the TX buffer if full)
+ * @return 0 on success
+ */
+ int __putc(int c, bool);
+
+ /**
+ * Function: _putc
+ * Overloaded virtual function.
+ */
+ virtual int _putc(int c) { return __putc(c, true); }
+
+ /**
+ * Function: _getc
+ * Overloaded virtual function.
+ */
+ virtual int _getc() { return __getc(true); }
+
+ /**
+ * Function: init
+ * Initialize the MODSERIAL object
+ * @ingroup INTERNALS
+ */
+ void init(int txSize, int rxSize);
+
+ /**
+ * Function: flushBuffer
+ * @ingroup INTERNALS
+ */
+ void flushBuffer(IrqType type);
+
+ /**
+ * Function: resizeBuffer
+ * @ingroup INTERNALS
+ */
+ int resizeBuffer(int size, IrqType type = RxIrq, bool memory_check = true);
+
+ /**
+ * Function: downSizeBuffer
+ * @ingroup INTERNALS
+ */
+ int downSizeBuffer(int size, IrqType type, bool memory_check);
+
+ /**
+ * Function: upSizeBuffer
+ * @ingroup INTERNALS
+ */
+ int upSizeBuffer(int size, IrqType type, bool memory_check);
+
+ /*
+ * If MODDMA is available the compile in code to handle sending
+ * an arbitary char buffer. Note, the parts before teh #ifdef
+ * are declared so that MODSERIAL can access then even if MODDMA
+ * isn't avaiable. Since MODDMA.h is only available at this point
+ * all DMA functionality must be declared inline in the class
+ * definition.
+ */
+public:
+
+ int dmaSendChannel;
+ void *moddma_p;
+
+#ifdef MODDMA_H
+
+ MODDMA_Config *config;
+
+ /**
+ * Set the "void pointer" moddma_p to be a pointer to a
+ * MODDMA controller class instance. Used to manage the
+ * data transfer of DMA configurations.
+ *
+ * @ingroup API
+ * @param p A pointer to "the" instance of MODDMA.
+ */
+ void MODDMA(MODDMA *p) { moddma_p = p; }
+
+ /**
+ * Send a char buffer to the Uarts TX system
+ * using DMA. This blocks regular library
+ * sending.
+ *
+ * @param buffer A char buffer of bytes to send.
+ * @param len The length of the buffer to send.
+ * @param dmaChannel The DMA channel to use, defaults to 7
+ * @return MODDMA::Status MODDMA::ok if all went ok
+ */
+ int dmaSend(char *buffer, int len, int dmaChannel = 7)
+ {
+ if (moddma_p == (void *)NULL) return -2;
+ class MODDMA *dma = (class MODDMA *)moddma_p;
+
+ dmaSendChannel = dmaChannel & 0x7;
+
+ uint32_t conn = MODDMA::UART0_Tx;
+ switch(_uidx) {
+ case 0: conn = MODDMA::UART0_Tx; break;
+ case 1: conn = MODDMA::UART1_Tx; break;
+ case 2: conn = MODDMA::UART2_Tx; break;
+ case 3: conn = MODDMA::UART3_Tx; break;
+ }
+
+ config = new MODDMA_Config;
+ config
+ ->channelNum ( (MODDMA::CHANNELS)(dmaSendChannel & 0x7) )
+ ->srcMemAddr ( (uint32_t) buffer )
+ ->transferSize ( len )
+ ->transferType ( MODDMA::m2p )
+ ->dstConn ( conn )
+ ->attach_tc ( this, &MODSERIAL::dmaSendCallback )
+ ->attach_err ( this, &MODSERIAL::dmaSendCallback )
+ ; // config end
+
+ // Setup the configuration.
+ if (dma->Setup(config) == 0) {
+ return -1;
+ }
+
+ //dma.Enable( MODDMA::Channel_0 );
+ dma->Enable( config->channelNum() );
+ return MODDMA::Ok;
+ }
+
+ /**
+ * Attach a callback to the DMA completion.
+ *
+ * @ingroup API
+ * @param fptr A function pointer to call
+ * @return this
+ */
+ void attach_dmaSendComplete(void (*fptr)(MODSERIAL_IRQ_INFO *)) {
+ _isrDmaSendComplete.attach(fptr);
+ }
+
+ /**
+ * Attach a callback to the DMA completion.
+ *
+ * @ingroup API
+ * @param tptr A template pointer to the calling object
+ * @param mptr A method pointer within the object to call.
+ * @return this
+ */
+ template<typename T>
+ void attach_dmaSendComplete(T* tptr, void (T::*mptr)(MODSERIAL_IRQ_INFO *)) {
+ if((mptr != NULL) && (tptr != NULL)) {
+ _isrDmaSendComplete.attach(tptr, mptr);
+ }
+ }
+
+ MODSERIAL_callback _isrDmaSendComplete;
+
+protected:
+ /**
+ * Callback for dmaSend().
+ */
+ void dmaSendCallback(void)
+ {
+ if (moddma_p == (void *)NULL) return;
+ class MODDMA *dma = (class MODDMA *)moddma_p;
+
+ MODDMA_Config *config = dma->getConfig();
+ dma->haltAndWaitChannelComplete( (MODDMA::CHANNELS)config->channelNum());
+ dma->Disable( (MODDMA::CHANNELS)config->channelNum() );
+ if (dma->irqType() == MODDMA::TcIrq) dma->clearTcIrq();
+ if (dma->irqType() == MODDMA::ErrIrq) dma->clearErrIrq();
+ dmaSendChannel = -1;
+ _isrDmaSendComplete.call(&this->callbackInfo);
+ delete(config);
+ }
+
+#endif // MODDMA_H
+
+};
+
+}; // namespace AjK ends
+
+using namespace AjK;
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/MODSERIAL_IRQ_INFO.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,38 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file MODSERIAL_IRQ_INFO.cpp
+ @author Andy Kirkham
+*/
+
+#include "MODSERIAL.h"
+
+namespace AjK {
+
+int
+MODSERIAL_IRQ_INFO::rxDiscardLastChar(void)
+{
+ if (!serial) return -1;
+
+ return serial->rxDiscardLastChar();
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/PUTC.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,81 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+int
+MODSERIAL::__putc(int c, bool block) {
+
+ // If no buffer is in use fall back to standard TX FIFO usage.
+ // Note, we must block in this case and ignore bool "block"
+ // so as to maintain compat with Mbed Serial.
+ if (buffer[TxIrq] == (char *)NULL || buffer_size[TxIrq] == 0) {
+ while (! MODSERIAL_THR_HAS_SPACE) ; // Wait for space in the TX FIFO.
+ _THR = (uint32_t)c;
+ return 0;
+ }
+
+ if ( MODSERIAL_THR_HAS_SPACE && MODSERIAL_TX_BUFFER_EMPTY && dmaSendChannel == -1 ) {
+ _THR = (uint32_t)c;
+ }
+ else {
+ if (block) {
+ uint32_t ier = _IER; _IER = 1;
+ while ( MODSERIAL_TX_BUFFER_FULL ) { // Blocks!
+ // If putc() is called from an ISR then we are stuffed
+ // because in an ISR no bytes from the TX buffer will
+ // get transferred to teh TX FIFOs while we block here.
+ // So, to work around this, instead of sitting in a
+ // loop waiting for space in the TX buffer (which will
+ // never happen in IRQ context), check to see if the
+ // TX FIFO has space available to move bytes from the
+ // TX buffer to TX FIFO to make space. The easiest way
+ // to do this is to poll the isr_tx() function while we
+ // are blocking.
+ isr_tx(false);
+ }
+ _IER = ier;
+ }
+ else if( MODSERIAL_TX_BUFFER_FULL ) {
+ buffer_overflow[TxIrq] = c; // Oh dear, no room in buffer.
+ _isr[TxOvIrq].call(&this->callbackInfo);
+ return -1;
+ }
+ _IER &= ~2;
+ buffer[TxIrq][buffer_in[TxIrq]] = c;
+ __disable_irq();
+ buffer_count[TxIrq]++;
+ __enable_irq();
+ buffer_in[TxIrq]++;
+ if (buffer_in[TxIrq] >= buffer_size[TxIrq]) {
+ buffer_in[TxIrq] = 0;
+ }
+ _IER |= 2;
+ }
+
+ return 0;
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/RESIZE.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,123 @@
+/*
+ Copyright (c) 2010 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+*/
+
+#include "MODSERIAL.h"
+#include "MACROS.h"
+
+namespace AjK {
+
+int
+MODSERIAL::resizeBuffer(int size, IrqType type, bool memory_check)
+{
+ int rval = Ok;
+
+ // If the requested size is the same as the current size there's nothing to do,
+ // just continue to use the same buffer as it's fine as it is.
+ if (buffer_size[type] == size) return rval;
+
+ // Make sure the ISR cannot use the buffers while we are manipulating them.
+ disableIrq();
+
+ // If the requested buffer size is larger than the current size,
+ // attempt to create a new buffer and use it.
+ if (buffer_size[type] < size) {
+ rval = upSizeBuffer(size, type, memory_check);
+ }
+ else if (buffer_size[type] > size) {
+ rval = downSizeBuffer(size, type, memory_check);
+ }
+
+ // Start the ISR system again with the new buffers.
+ enableIrq();
+
+ return rval;
+}
+
+int
+MODSERIAL::downSizeBuffer(int size, IrqType type, bool memory_check)
+{
+ if (size >= buffer_count[type]) {
+ return BufferOversize;
+ }
+
+ char *s = (char *)malloc(size);
+
+ if (s == (char *)NULL) {
+ if (memory_check) {
+ error("Failed to allocate memory for %s buffer", type == TxIrq ? "TX" : "RX");
+ }
+ return NoMemory;
+ }
+
+ int c, new_in = 0;
+
+ do {
+ c = __getc(false);
+ if (c != -1) s[new_in++] = (char)c;
+ if (new_in >= size) new_in = 0;
+ }
+ while (c != -1);
+
+ free((char *)buffer[type]);
+ buffer[type] = s;
+ buffer_in[type] = new_in;
+ buffer_out[type] = 0;
+ return Ok;
+}
+
+int
+MODSERIAL::upSizeBuffer(int size, IrqType type, bool memory_check)
+{
+ char *s = (char *)malloc(size);
+
+ if (s == (char *)NULL) {
+ if (memory_check) {
+ error("Failed to allocate memory for %s buffer", type == TxIrq ? "TX" : "RX");
+ }
+ return NoMemory;
+ }
+
+ if (buffer_count[type] == 0) { // Current buffer empty?
+ free((char *)buffer[type]);
+ buffer[type] = s;
+ buffer_in[type] = 0;
+ buffer_out[type] = 0;
+ }
+ else { // Copy the current contents into the new buffer.
+ int c, new_in = 0;
+ do {
+ c = __getc(false);
+ if (c != -1) s[new_in++] = (char)c;
+ if (new_in >= size) new_in = 0; // Shouldn't happen, but be sure.
+ }
+ while (c != -1);
+ free((char *)buffer[type]);
+ buffer[type] = s;
+ buffer_in[type] = new_in;
+ buffer_out[type] = 0;
+ }
+
+ buffer_size[type] = size;
+ return Ok;
+}
+
+}; // namespace AjK ends
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/example1.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,120 @@
+#ifdef COMPILE_EXAMPLE1_CODE_MODSERIAL
+
+/*
+ * To run this test program, link p9 to p10 so the Serial loops
+ * back and receives characters it sends.
+ */
+
+#include "mbed.h"
+#include "MODSERIAL.h"
+
+DigitalOut led1(LED1);
+DigitalOut led2(LED2);
+DigitalOut led3(LED3);
+DigitalOut led4(LED4);
+
+MODSERIAL pc(USBTX, USBRX);
+
+/*
+ * As experiement, you can define MODSERIAL as show here and see what
+ * effects it has on the LEDs.
+ *
+ * MODSERIAL uart(TX_PIN, RX_PIN, 512);
+ * With this, the 512 characters sent can straight into the buffer
+ * vary quickly. This means LED1 is only on briefly as the TX buffer
+ * fills.
+ *
+ * MODSERIAL uart(TX_PIN, RX_PIN, 32);
+ * With this, the buffer is smaller than the default 256 bytes and
+ * therefore LED1 stays on much longer while the system waits for
+ * room in the TX buffer.
+ */
+MODSERIAL uart(TX_PIN, RX_PIN);
+
+// This function is called when a character goes from the TX buffer
+// to the Uart THR FIFO register.
+void txCallback(MODSERIAL_IRQ_INFO *q) {
+ led2 = !led2;
+}
+
+// This function is called when TX buffer goes empty
+void txEmpty(MODSERIAL_IRQ_INFO *q) {
+ led2 = 0;
+ pc.puts(" Done. ");
+}
+
+// This function is called when a character goes into the RX buffer.
+void rxCallback(MODSERIAL_IRQ_INFO *q) {
+ led3 = !led3;
+ pc.putc(uart.getc());
+}
+
+int main() {
+ int c = 'A';
+
+ // Ensure the baud rate for the PC "USB" serial is much
+ // higher than "uart" baud rate below.
+ pc.baud(PC_BAUD);
+
+ // Use a deliberatly slow baud to fill up the TX buffer
+ uart.baud(1200);
+
+ uart.attach(&txCallback, MODSERIAL::TxIrq);
+ uart.attach(&rxCallback, MODSERIAL::RxIrq);
+ uart.attach(&txEmpty, MODSERIAL::TxEmpty);
+
+ // Loop sending characters. We send 512
+ // which is twice the default TX/RX buffer size.
+
+ led1 = 1; // Show start of sending with LED1.
+
+ for (int loop = 0; loop < 512; loop++) {
+ uart.printf("%c", c);
+ c++;
+ if (c > 'Z') c = 'A';
+ }
+
+ led1 = 0; // Show the end of sending by switching off LED1.
+
+ // End program. Flash LED4. Notice how LED 2 and 3 continue
+ // to flash for a short period while the interrupt system
+ // continues to send the characters left in the TX buffer.
+
+ while(1) {
+ led4 = !led4;
+ wait(0.25);
+ }
+}
+
+/*
+ * Notes. Here is the sort of output you can expect on your PC/Mac/Linux host
+ * machine that is connected to the "pc" USB serial port.
+ *
+ * ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUV
+ * WXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQR
+ * STUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMN
+ * OPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJ
+ * KLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEF
+ * GHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZAB
+ * CDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQ Done. R
+ *
+ * Of interest is that last "R" character after the system has said "Done."
+ * This comes from the fact that the TxEmpty callback is made when the TX buffer
+ * becomes empty. MODSERIAL makes use of the fact that the Uarts built into the
+ * LPC17xx device use a 16 byte FIFO on both RX and TX channels. This means that
+ * when the TxEmpty callback is made, the TX buffer is empty, but that just means
+ * the "last few characters" were written to the TX FIFO. So although the TX
+ * buffer has gone empty, the Uart's transmit system is still sending any remaining
+ * characters from it's TX FIFO. If you want to be truely sure all the characters
+ * you have sent have left the Mbed then call txIsBusy(); This function will
+ * return true if characters are still being sent. If it returns false after
+ * the Tx buffer is empty then all your characters have been sent.
+ *
+ * In a similar way, when characters are received into the RX FIFO, the entire
+ * FIFO contents is moved to the RX buffer, assuming there is room left in the
+ * RX buffer. If there is not, any remaining characters are left in the RX FIFO
+ * and will be moved to the RX buffer on the next interrupt or when the running
+ * program removes a character(s) from the RX buffer with the getc() method.
+ */
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/example2.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,167 @@
+/*
+ Copyright (c) 2011 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file example2.cpp
+ @purpose Demos a simple messaging system.
+ @version see ChangeLog.c
+ @date Jan 2011
+ @author Andy Kirkham
+*/
+
+/*
+ This example demostrates a simple "messaging" system. You can use it with
+ a terminal program to test it out or write a cusom C#/C++/VB/etc program
+ to read and write messages to or from the Mbed. The default baud rate in
+ this example is 115200.
+
+ In this example, the LEDs are controlled and pins p21 to p24 are set as
+ InterruptIn and send messages out when their value changes.
+
+ To use, hook up the MBed USB and open your fav terminal. All messages
+ end with the \n character, don't forget to hit carriage return!.
+ As an example:-
+
+ to switch on LED1 send LED1:1\n, off is LED1:0\n and toggle is LED1:2\n
+ to switch on LED2 send LED2:1\n, off is LED2:0\n and toggle is LED2:2\n
+ to switch on LED3 send LED3:1\n, off is LED3:0\n and toggle is LED3:2\n
+ to switch on LED4 send LED4:1\n, off is LED4:0\n and toggle is LED4:2\n
+
+ When a pin change on p21 to p24 happens, a message is sent. As an example
+ when p21 goes low PIN21:0\n is sent, when goes high PIN21:1\n is sent.
+
+ Note, the InterruptIn pins p21 to p24 are setup to have pullups. This means
+ they are high. To activate them use a wire to short the pin to 0volts.
+
+ If you find that p21 to p24 sent a lot of on/off/on/off then it's probably
+ due to "bounce". If you are connecting a mechanical switch to a pin you
+ may prefer to use the PinDetect library rather than using InterruptIn.
+ @see http://mbed.org/users/AjK/libraries/PinDetect/latest
+
+ One point you may notice. Incoming messages are processed via main()'s
+ while(1) loop whereas pin changes have their messages directly sent.
+ The reason for this is when MODSERIAL makes callbacks to your application
+ it is in "interrupt context". And one thing you want to avoid is spending
+ lots of CPU time in that context. So, the callback moves the message from
+ the input buffer to a local holding buffer and it then sets a bool flag
+ which tells main()'s while(1) loop to process that buffer. This means the
+ time spent doing the real incoming message handing is within your program
+ and not within MODSERIAL's interrupt context. So you may ask, why not do
+ the same for out going messages? Well, because MODSERIAL output buffers
+ all your sent content then sending chars is very fast. MODSERIAL handles
+ all the nitty gritty bits for you. You can just send. This example uses
+ puts() to send the message. If you can, always try and use sprintf()+puts()
+ rathe than printf(), printf() is known to often screw things up when used
+ within an interrupt context. Better still, just use puts() and do away
+ with any of the crappy ?printf() calls if possible. But I found the code
+ below to work fine even at 115200baud.
+
+*/
+
+
+#ifdef COMPILE_EXAMPLE1_CODE_MODSERIAL
+
+#include "mbed.h"
+#include "MODSERIAL.h"
+
+#define MESSAGE_BUFFER_SIZE 32
+
+DigitalOut led1(LED1);
+DigitalOut led2(LED2);
+DigitalOut led3(LED3);
+DigitalOut led4(LED4);
+
+InterruptIn P21(p21);
+InterruptIn P22(p22);
+InterruptIn P23(p23);
+InterruptIn P24(p24);
+
+MODSERIAL messageSystem(USBTX, USBRX);
+
+char messageBufferIncoming[MESSAGE_BUFFER_SIZE];
+char messageBufferOutgoing[MESSAGE_BUFFER_SIZE];
+bool messageReceived;
+
+void messageReceive(MODSERIAL_IRQ_INFO *q) {
+ MODSERIAL *sys = q->serial;
+ sys->move(messageBufferIncoming, MESSAGE_BUFFER_SIZE);
+ messageReceived = true;
+ return 0;
+}
+
+void messageProcess(void) {
+ if (!strncmp(messageBufferIncoming, "LED1:1", sizeof("LED1:1")-1)) led1 = 1;
+ else if (!strncmp(messageBufferIncoming, "LED1:0", sizeof("LED1:0")-1)) led1 = 0;
+ else if (!strncmp(messageBufferIncoming, "LED1:2", sizeof("LED1:2")-1)) led1 = !led1;
+
+ else if (!strncmp(messageBufferIncoming, "LED2:1", sizeof("LED2:1")-1)) led2 = 1;
+ else if (!strncmp(messageBufferIncoming, "LED2:0", sizeof("LED2:0")-1)) led2 = 0;
+ else if (!strncmp(messageBufferIncoming, "LED2:2", sizeof("LED2:2")-1)) led2 = !led2;
+
+ else if (!strncmp(messageBufferIncoming, "LED3:1", sizeof("LED3:1")-1)) led3 = 1;
+ else if (!strncmp(messageBufferIncoming, "LED3:0", sizeof("LED3:0")-1)) led3 = 0;
+ else if (!strncmp(messageBufferIncoming, "LED3:2", sizeof("LED3:2")-1)) led3 = !led3;
+
+ else if (!strncmp(messageBufferIncoming, "LED4:1", sizeof("LED4:1")-1)) led4 = 1;
+ else if (!strncmp(messageBufferIncoming, "LED4:0", sizeof("LED4:0")-1)) led4 = 0;
+ else if (!strncmp(messageBufferIncoming, "LED4:2", sizeof("LED4:2")-1)) led4 = !led4;
+
+ messageReceived = false;
+}
+
+#define PIN_MESSAGE_SEND(x,y) \
+ sprintf(messageBufferOutgoing,"PIN%02d:%d\n",x,y);\
+ messageSystem.puts(messageBufferOutgoing);
+
+void pin21Rise(void) { PIN_MESSAGE_SEND(21, 1); }
+void pin21Fall(void) { PIN_MESSAGE_SEND(21, 0); }
+void pin22Rise(void) { PIN_MESSAGE_SEND(22, 1); }
+void pin22Fall(void) { PIN_MESSAGE_SEND(22, 0); }
+void pin23Rise(void) { PIN_MESSAGE_SEND(23, 1); }
+void pin23Fall(void) { PIN_MESSAGE_SEND(23, 0); }
+void pin24Rise(void) { PIN_MESSAGE_SEND(24, 1); }
+void pin24Fall(void) { PIN_MESSAGE_SEND(24, 0); }
+
+int main() {
+
+ messageReceived = false;
+ messageSystem.baud(115200);
+ messageSystem.attach(&messageReceive, MODSERIAL::RxAutoDetect);
+ messageSystem.autoDetectChar('\n');
+
+ // Enable pullup resistors on pins.
+ P21.mode(PullUp); P22.mode(PullUp); P23.mode(PullUp); P24.mode(PullUp);
+
+ // Fix Mbed library bug, see http://mbed.org/forum/bugs-suggestions/topic/1498
+ LPC_GPIOINT->IO2IntClr = (1UL << 5) | (1UL << 4) | (1UL << 3) | (1UL << 2);
+
+ // Attach InterruptIn pin callbacks.
+ P21.rise(&pin21Rise); P21.fall(&pin21Fall);
+ P22.rise(&pin22Rise); P22.fall(&pin22Fall);
+ P23.rise(&pin23Rise); P23.fall(&pin23Fall);
+ P24.rise(&pin24Rise); P24.fall(&pin24Fall);
+
+ while(1) {
+ // Process incoming messages.
+ if (messageReceived) messageProcess();
+ }
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/example3a.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,83 @@
+/*
+ Copyright (c) 2011 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file example3.cpp
+ @purpose Demos a simple filter.
+ @version see ChangeLog.c
+ @author Andy Kirkham
+*/
+
+/*
+ This example shows how to use the new callback system. In the old system
+ Mbed's FunctionPointer[1] type was used to store abd make calls to callbacks.
+ However, that limits the callback function prototype to void func(void);
+ which means we cannot pass parameters.
+
+ This latest version of MODSERIAL now uses its own callback object. This allows
+ the passing of a pointer to a class that holds information about the MODSERIAL
+ object making the callback. As of version 1.18 one critcal piece of information
+ is passed, a pointer to the MODSERIAL object. This allows callbacks to use the
+ MODSERIAL functions and data.
+
+ Additionally, since MODSERIAL and the callback parameter class MODSERIAL_IRQ_INFO
+ are friends, MODSERIAL_IRQ_INFO can access the protected functions of MODSERIAL.
+ This is used to ensure functions that can only be called during a callback
+ can be invoked from a callback.
+
+ [1] http://mbed.org/projects/libraries/svn/mbed/trunk/FunctionPointer.h
+*/
+
+#ifdef COMPILE_EXAMPLE3_CODE_MODSERIAL
+
+#include "mbed.h"
+#include "MODSERIAL.h"
+
+DigitalOut led1(LED1);
+
+MODSERIAL pc(USBTX, USBRX);
+
+// The following callback is defined in example3b.cpp
+//! @see example3b.cpp
+void rxCallback(MODSERIAL_IRQ_INFO *info);
+
+int main() {
+
+ int life_counter = 0;
+
+ pc.baud(115200);
+
+ pc.attach(&rxCallback, MODSERIAL::RxIrq);
+
+ while(1) {
+ // Echo back any chars we get except 'A' which is filtered by the rxCallback.
+ if (pc.readable()) {
+ pc.putc(pc.getc());
+ }
+
+ // Toggle LED1 every so often to show we are alive.
+ if (life_counter++ == 1000000) {
+ life_counter = 0;
+ led1 = !led1;
+ }
+ }
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/example3b.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,78 @@
+/*
+ Copyright (c) 2011 Andy Kirkham
+
+ Permission is hereby granted, free of charge, to any person obtaining a copy
+ of this software and associated documentation files (the "Software"), to deal
+ in the Software without restriction, including without limitation the rights
+ to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ copies of the Software, and to permit persons to whom the Software is
+ furnished to do so, subject to the following conditions:
+
+ The above copyright notice and this permission notice shall be included in
+ all copies or substantial portions of the Software.
+
+ THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ THE SOFTWARE.
+
+ @file example3b.cpp
+ @purpose Demos a simple filter.
+ @version see ChangeLog.c
+ @author Andy Kirkham
+*/
+
+/*
+ This example shows how to use the new callback system. In the old system
+ Mbed's FunctionPointer[1] type was used to store abd make calls to callbacks.
+ However, that limits the callback function prototype to void func(void);
+ which means we cannot pass parameters.
+
+ This latest version of MODSERIAL now uses its own callback object. This allows
+ the passing of a pointer to a class that holds information about the MODSERIAL
+ object making the callback. As of version 1.18 one critcal piece of information
+ is passed, a pointer to the MODSERIAL object. This allows callbacks to use the
+ MODSERIAL functions and data.
+
+ Additionally, since MODSERIAL and the callback parameter class MODSERIAL_IRQ_INFO
+ are friends, MODSERIAL_IRQ_INFO can access the protected functions of MODSERIAL.
+ This is used to ensure functions that can only be called during a callback
+ can be invoked from a callback.
+
+ [1] http://mbed.org/projects/libraries/svn/mbed/trunk/FunctionPointer.h
+*/
+
+
+#ifdef COMPILE_EXAMPLE3_CODE_MODSERIAL
+
+#include "mbed.h"
+#include "MODSERIAL.h"
+
+void rxCallback(MODSERIAL_IRQ_INFO *info) {
+
+ // Get the pointer to our MODSERIAL object that invoked this callback.
+ MODSERIAL *pc = info->serial;
+
+ // info->serial points at the MODSERIAL instance so we can use it to call
+ // any of the public MODSERIAL functions that are normally available. So
+ // there's now no need to use the global version (pc in our case) inside
+ // callback functions.
+ char c = pc->rxGetLastChar(); // Where local pc variable is a pointer to the global MODSERIAL pc object.
+
+ // The following is rather daft but demos the point.
+ // Don't allow the letter "A" go into the RX buffer.
+ // Basically acts as a filter to remove the letter "A"
+ // if it goes into the RX buffer.
+ if (c == 'A') {
+ // Note, we call the MODSERIAL_IRQ_INFO::rxDiscardLastChar() public function which
+ // is permitted access to the protected version of MODSERIAL::rxDiscardLastChar()
+ // within MODSERIAL (because they are friends). This ensures rxDiscardLastChar()
+ // can only be called within an rxCallback function.
+ info->rxDiscardLastChar();
+ }
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/MODSERIAL/example_dma.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,144 @@
+#ifdef COMPILE_EXAMPLE_CODE_MODSERIAL_MODDMA
+
+/*
+ * To run this test program, link p9 to p10 so the Serial loops
+ * back and receives characters it sends.
+ */
+
+#include "mbed.h"
+
+/* Note, this example requires that you also import into the Mbed
+ compiler the MODDMA project as well as MODSERIAL
+ http://mbed.org/users/AjK/libraries/MODDMA/latest
+ MODDMA.h MUST come before MODSERIAL.h */
+#include "MODDMA.h" // <--- Declare first
+#include "MODSERIAL.h" // Flollowed by MODSERIAL
+
+DigitalOut led1(LED1);
+DigitalOut led2(LED2);
+DigitalOut led3(LED3);
+DigitalOut led4(LED4);
+
+MODSERIAL pc(USBTX, USBRX);
+
+/*
+ * As experiement, you can define MODSERIAL as show here and see what
+ * effects it has on the LEDs.
+ *
+ * MODSERIAL uart(TX_PIN, RX_PIN, 512);
+ * With this, the 512 characters sent can straight into the buffer
+ * vary quickly. This means LED1 is only on briefly as the TX buffer
+ * fills.
+ *
+ * MODSERIAL uart(TX_PIN, RX_PIN, 32);
+ * With this, the buffer is smaller than the default 256 bytes and
+ * therefore LED1 stays on much longer while the system waits for
+ * room in the TX buffer.
+ */
+MODSERIAL uart(TX_PIN, RX_PIN);
+
+MODDMA dma;
+
+// This function is called when a character goes from the TX buffer
+// to the Uart THR FIFO register.
+void txCallback(void) {
+ led2 = !led2;
+}
+
+// This function is called when TX buffer goes empty
+void txEmpty(void) {
+ led2 = 0;
+ pc.puts(" Done. ");
+}
+
+void dmaComplete(void) {
+ led1 = 1;
+}
+
+// This function is called when a character goes into the RX buffer.
+void rxCallback(void) {
+ led3 = !led3;
+ pc.putc(uart.getc());
+}
+
+int main() {
+ char s1[] = " *DMA* *DMA* *DMA* *DMA* *DMA* *DMA* *DMA* ";
+ int c = 'A';
+
+ // Tell MODSERIAL where the MODDMA controller is.
+ pc.MODDMA( &dma );
+
+ // Ensure the baud rate for the PC "USB" serial is much
+ // higher than "uart" baud rate below.
+ pc.baud( PC_BAUD );
+
+ // Use a deliberatly slow baud to fill up the TX buffer
+ uart.baud(1200);
+
+ uart.attach( &txCallback, MODSERIAL::TxIrq );
+ uart.attach( &rxCallback, MODSERIAL::RxIrq );
+ uart.attach( &txEmpty, MODSERIAL::TxEmpty );
+
+ // Loop sending characters. We send 512
+ // which is twice the default TX/RX buffer size.
+
+ led1 = 0;
+
+ // Send the buffer s using DMA channel 7
+ pc.attach_dmaSendComplete( &dmaComplete );
+ pc.dmaSend( s1, sizeof(s1), MODDMA::Channel_7 );
+
+ for (int loop = 0; loop < 512; loop++) {
+ uart.printf("%c", c);
+ c++;
+ if (c > 'Z') c = 'A';
+ }
+
+ led1 = 0; // Show the end of sending by switching off LED1.
+
+ // End program. Flash LED4. Notice how LED 2 and 3 continue
+ // to flash for a short period while the interrupt system
+ // continues to send the characters left in the TX buffer.
+
+ while(1) {
+ led4 = !led4;
+ wait(0.25);
+ }
+}
+
+/*
+ * Notes. Here is the sort of output you can expect on your PC/Mac/Linux host
+ * machine that is connected to the "pc" USB serial port.
+ *
+ * *DMA* *DMA* *DMA* *DMA* *DMA* *DMA* *DMA* ABCDEFGHIJKLMNOPQRSTUVWXYZABCDE
+ * FGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZA
+ * BCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVW
+ * XYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRS
+ * TUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNO
+ * PQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJK
+ * LMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFG
+ * HIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMNOPQ Done. R
+ *
+ * Note how the DMA blocks the TX buffer sending under standard interrupt control.
+ * Not until the DMA transfer is complete will "normal" buffered TX sending resume.
+ *
+ * Of interest is that last "R" character after the system has said "Done."
+ * This comes from the fact that the TxEmpty callback is made when the TX buffer
+ * becomes empty. MODSERIAL makes use of the fact that the Uarts built into the
+ * LPC17xx device use a 16 byte FIFO on both RX and TX channels. This means that
+ * when the TxEmpty callback is made, the TX buffer is empty, but that just means
+ * the "last few characters" were written to the TX FIFO. So although the TX
+ * buffer has gone empty, the Uart's transmit system is still sending any remaining
+ * characters from it's TX FIFO. If you want to be truely sure all the characters
+ * you have sent have left the Mbed then call txIsBusy(); This function will
+ * return true if characters are still being sent. If it returns false after
+ * the Tx buffer is empty then all your characters have been sent.
+ *
+ * In a similar way, when characters are received into the RX FIFO, the entire
+ * FIFO contents is moved to the RX buffer, assuming there is room left in the
+ * RX buffer. If there is not, any remaining characters are left in the RX FIFO
+ * and will be moved to the RX buffer on the next interrupt or when the running
+ * program removes a character(s) from the RX buffer with the getc() method.
+ */
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/OEM615.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,130 @@
+
+#pragma pack(1) //this forces the structure to be packed on byte boundaries (with no byte filler)
+//set up the GPS message header in a structure to enable easy reading -- see the OEM615 manual (Table 4, page 24)
+struct MESSAGEHEADER
+{
+ char synchAA; //1st synch word
+ char synch44; //2nd synch word
+ char synch12; //3rd synch word
+ unsigned char headerLength; //always 28
+ unsigned short messageID;
+ char messageType; //always = 0 for binary
+ unsigned char portAddress; //0x20 for COM1
+ unsigned short messageLength; //not including header or CRC
+ unsigned short sequence; //typically 0
+ unsigned char idleTime; //Time the processor is idle, in the last second
+ unsigned char timeStatus; //Enum Indicating quality of the GPS reference time
+ unsigned short GPSweek; //GPS reference week
+ unsigned long GPSTime_msecs; //from beginning of week
+ unsigned long receiverStatus; //32-bits representing the status of hardware and software
+ unsigned short reserved;
+ unsigned short receiverSWversion; //receiver software build number
+};
+MESSAGEHEADER *msgHeader[4];
+
+#pragma pack(1)
+//structure for OEM615 BESTVEL log message (page 314)
+struct OEM615BESTVEL
+{
+ MESSAGEHEADER msgHeader;
+ int solStatus; //solution status
+ //solutionStatusOEMStar solStatus; //solution status
+ int velType; //position or velocity type
+ //velTypeOEMStar posType; //position or velocity type
+ float latency;
+ float age;
+ double horizontalSpeed; //horizontal velocity vector magnitude (m/s)
+ double heading; //deg from North called TRK GND in specification
+ double verticalSpeed; //vertical velocity magnitude (m/s)
+ float reserved;
+ unsigned long CRC;
+};
+
+#pragma pack(1)
+//structure for BESTPOS message
+struct OEM615BESTPOS
+{
+ MESSAGEHEADER msgHeader;
+ int solStatus; //solution status
+ //solutionStatusOEMStar solStatus; //solution status
+ int posType; //position or velocity type
+ //posTypeOEMStar posType; //position or velocity type
+ double latitude; //latitude
+ double longitude; //longitude
+ double height; //height above mean sea level
+ float undulation; //the realtionship between the geoid and the
+ //ellipsoid of the chosen datum (m)
+ char datumID[4]; //datum ID is actually an enum that is not implemented
+ float latitudeSTD; //latitude standard deviation
+ float longitudeSTD; //longitude standard deviation
+ float heightSTD; //height standard deviation
+ char baseStationID[4]; //base station ID
+ float diffAge; //differential age (s)
+ float solutionAge; //solution age (s)
+ unsigned char numSV; //number of satellite vehicles tracked
+ unsigned char numSolSV; //number of satellite vehicles used in solution
+ unsigned char numGGL1; //number of GPS plus Glonass L1
+ unsigned char res1;
+ unsigned char res2;
+ unsigned char extSolStatus; //extended solution status
+ unsigned char res3;
+ unsigned char sigMask; //signals used mask
+ unsigned long CRC;
+};
+
+
+//this code was taken from the Novatel Firmware document page 35
+#define CRC32_POLYNOMIAL 0xEDB88320L
+/* --------------------------------------------------------------------------
+Calculate a CRC value to be used by CRC calculation functions.
+-------------------------------------------------------------------------- */
+unsigned long CRC32Value(int i)
+{
+ int j;
+ unsigned long ulCRC;
+ ulCRC = i;
+ for ( j = 8 ; j > 0; j-- )
+ {
+ if ( ulCRC & 1 )
+ ulCRC = ( ulCRC >> 1 ) ^ CRC32_POLYNOMIAL;
+ else
+ ulCRC >>= 1;
+ }
+ return ulCRC;
+}
+
+/* --------------------------------------------------------------------------
+Calculates the CRC-32 of a block of data all at once
+//the CRC is c from the complete message (header plus data) but excluding (of course) the CRC at the end
+-------------------------------------------------------------------------- */
+unsigned long CalculateBlockCRC32(
+ unsigned long ulCount, /* Number of bytes in the data block */
+ unsigned char *ucBuffer ) /* Data block */
+{
+ unsigned long ulTemp1;
+ unsigned long ulTemp2;
+ unsigned long ulCRC = 0;
+ while ( ulCount-- != 0 )
+ {
+ ulTemp1 = ( ulCRC >> 8 ) & 0x00FFFFFFL;
+ ulTemp2 = CRC32Value( ((int) ulCRC ^ *ucBuffer++ ) & 0xff );
+ ulCRC = ulTemp1 ^ ulTemp2;
+ }
+ return( ulCRC );
+}
+
+//GPS-specific pins
+DigitalOut GPS_Reset(p18); //GPS RESET line
+InterruptIn PPSInt(p15); // GPS 1PPS (timemark) from the OEM615
+InterruptIn IMUClock(p17);
+
+Timer timeFromPPS;
+unsigned long GPSTimemsecs = 0;
+double GPSTime = 0;
+int PPSTimeOffset = 0;
+
+//mbed tx/rx interface to the GPS COM1 port
+MODSERIAL GPS_COM1(p9,p10); //this serial port communicates with the GPS receiver serial port (COM1)
+
+
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/SDFileSystem/SDFileSystem.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,457 @@
+/* mbed SDFileSystem Library, for providing file access to SD cards
+ * Copyright (c) 2008-2010, sford
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+/* Introduction
+ * ------------
+ * SD and MMC cards support a number of interfaces, but common to them all
+ * is one based on SPI. This is the one I'm implmenting because it means
+ * it is much more portable even though not so performant, and we already
+ * have the mbed SPI Interface!
+ *
+ * The main reference I'm using is Chapter 7, "SPI Mode" of:
+ * http://www.sdcard.org/developers/tech/sdcard/pls/Simplified_Physical_Layer_Spec.pdf
+ *
+ * SPI Startup
+ * -----------
+ * The SD card powers up in SD mode. The SPI interface mode is selected by
+ * asserting CS low and sending the reset command (CMD0). The card will
+ * respond with a (R1) response.
+ *
+ * CMD8 is optionally sent to determine the voltage range supported, and
+ * indirectly determine whether it is a version 1.x SD/non-SD card or
+ * version 2.x. I'll just ignore this for now.
+ *
+ * ACMD41 is repeatedly issued to initialise the card, until "in idle"
+ * (bit 0) of the R1 response goes to '0', indicating it is initialised.
+ *
+ * You should also indicate whether the host supports High Capicity cards,
+ * and check whether the card is high capacity - i'll also ignore this
+ *
+ * SPI Protocol
+ * ------------
+ * The SD SPI protocol is based on transactions made up of 8-bit words, with
+ * the host starting every bus transaction by asserting the CS signal low. The
+ * card always responds to commands, data blocks and errors.
+ *
+ * The protocol supports a CRC, but by default it is off (except for the
+ * first reset CMD0, where the CRC can just be pre-calculated, and CMD8)
+ * I'll leave the CRC off I think!
+ *
+ * Standard capacity cards have variable data block sizes, whereas High
+ * Capacity cards fix the size of data block to 512 bytes. I'll therefore
+ * just always use the Standard Capacity cards with a block size of 512 bytes.
+ * This is set with CMD16.
+ *
+ * You can read and write single blocks (CMD17, CMD25) or multiple blocks
+ * (CMD18, CMD25). For simplicity, I'll just use single block accesses. When
+ * the card gets a read command, it responds with a response token, and then
+ * a data token or an error.
+ *
+ * SPI Command Format
+ * ------------------
+ * Commands are 6-bytes long, containing the command, 32-bit argument, and CRC.
+ *
+ * +---------------+------------+------------+-----------+----------+--------------+
+ * | 01 | cmd[5:0] | arg[31:24] | arg[23:16] | arg[15:8] | arg[7:0] | crc[6:0] | 1 |
+ * +---------------+------------+------------+-----------+----------+--------------+
+ *
+ * As I'm not using CRC, I can fix that byte to what is needed for CMD0 (0x95)
+ *
+ * All Application Specific commands shall be preceded with APP_CMD (CMD55).
+ *
+ * SPI Response Format
+ * -------------------
+ * The main response format (R1) is a status byte (normally zero). Key flags:
+ * idle - 1 if the card is in an idle state/initialising
+ * cmd - 1 if an illegal command code was detected
+ *
+ * +-------------------------------------------------+
+ * R1 | 0 | arg | addr | seq | crc | cmd | erase | idle |
+ * +-------------------------------------------------+
+ *
+ * R1b is the same, except it is followed by a busy signal (zeros) until
+ * the first non-zero byte when it is ready again.
+ *
+ * Data Response Token
+ * -------------------
+ * Every data block written to the card is acknowledged by a byte
+ * response token
+ *
+ * +----------------------+
+ * | xxx | 0 | status | 1 |
+ * +----------------------+
+ * 010 - OK!
+ * 101 - CRC Error
+ * 110 - Write Error
+ *
+ * Single Block Read and Write
+ * ---------------------------
+ *
+ * Block transfers have a byte header, followed by the data, followed
+ * by a 16-bit CRC. In our case, the data will always be 512 bytes.
+ *
+ * +------+---------+---------+- - - -+---------+-----------+----------+
+ * | 0xFE | data[0] | data[1] | | data[n] | crc[15:8] | crc[7:0] |
+ * +------+---------+---------+- - - -+---------+-----------+----------+
+ */
+
+#include "SDFileSystem.h"
+
+#define SD_COMMAND_TIMEOUT 5000
+
+SDFileSystem::SDFileSystem(PinName mosi, PinName miso, PinName sclk, PinName cs, const char* name) :
+ FATFileSystem(name), _spi(mosi, miso, sclk), _cs(cs) {
+ _cs = 1;
+}
+
+#define R1_IDLE_STATE (1 << 0)
+#define R1_ERASE_RESET (1 << 1)
+#define R1_ILLEGAL_COMMAND (1 << 2)
+#define R1_COM_CRC_ERROR (1 << 3)
+#define R1_ERASE_SEQUENCE_ERROR (1 << 4)
+#define R1_ADDRESS_ERROR (1 << 5)
+#define R1_PARAMETER_ERROR (1 << 6)
+
+// Types
+// - v1.x Standard Capacity
+// - v2.x Standard Capacity
+// - v2.x High Capacity
+// - Not recognised as an SD Card
+
+#define SDCARD_FAIL 0
+#define SDCARD_V1 1
+#define SDCARD_V2 2
+#define SDCARD_V2HC 3
+
+int SDFileSystem::initialise_card() {
+ // Set to 100kHz for initialisation, and clock card with cs = 1
+ _spi.frequency(100000);
+ _cs = 1;
+ for(int i=0; i<16; i++) {
+ _spi.write(0xFF);
+ }
+
+ // send CMD0, should return with all zeros except IDLE STATE set (bit 0)
+ if(_cmd(0, 0) != R1_IDLE_STATE) {
+ fprintf(stderr, "No disk, or could not put SD card in to SPI idle state\n");
+ return SDCARD_FAIL;
+ }
+
+ // send CMD8 to determine whther it is ver 2.x
+ int r = _cmd8();
+ if(r == R1_IDLE_STATE) {
+ return initialise_card_v2();
+ } else if(r == (R1_IDLE_STATE | R1_ILLEGAL_COMMAND)) {
+ return initialise_card_v1();
+ } else {
+ fprintf(stderr, "Not in idle state after sending CMD8 (not an SD card?)\n");
+ return SDCARD_FAIL;
+ }
+}
+
+int SDFileSystem::initialise_card_v1() {
+ for(int i=0; i<SD_COMMAND_TIMEOUT; i++) {
+ _cmd(55, 0);
+ if(_cmd(41, 0) == 0) {
+ return SDCARD_V1;
+ }
+ }
+
+ fprintf(stderr, "Timeout waiting for v1.x card\n");
+ return SDCARD_FAIL;
+}
+
+int SDFileSystem::initialise_card_v2() {
+
+ for(int i=0; i<SD_COMMAND_TIMEOUT; i++) {
+ _cmd(55, 0);
+ if(_cmd(41, 0) == 0) {
+ _cmd58();
+ return SDCARD_V2;
+ }
+ }
+
+ fprintf(stderr, "Timeout waiting for v2.x card\n");
+ return SDCARD_FAIL;
+}
+
+int SDFileSystem::disk_initialize() {
+
+ int i = initialise_card();
+// printf("init card = %d\n", i);
+// printf("OK\n");
+
+ _sectors = _sd_sectors();
+
+ // Set block length to 512 (CMD16)
+ if(_cmd(16, 512) != 0) {
+ fprintf(stderr, "Set 512-byte block timed out\n");
+ return 1;
+ }
+
+ _spi.frequency(1000000); // Set to 1MHz for data transfer
+ return 0;
+}
+
+int SDFileSystem::disk_write(const char *buffer, int block_number) {
+ // set write address for single block (CMD24)
+ if(_cmd(24, block_number * 512) != 0) {
+ return 1;
+ }
+
+ // send the data block
+ _write(buffer, 512);
+ return 0;
+}
+
+int SDFileSystem::disk_read(char *buffer, int block_number) {
+ // set read address for single block (CMD17)
+ if(_cmd(17, block_number * 512) != 0) {
+ return 1;
+ }
+
+ // receive the data
+ _read(buffer, 512);
+ return 0;
+}
+
+int SDFileSystem::disk_status() { return 0; }
+int SDFileSystem::disk_sync() { return 0; }
+int SDFileSystem::disk_sectors() { return _sectors; }
+
+// PRIVATE FUNCTIONS
+
+int SDFileSystem::_cmd(int cmd, int arg) {
+ _cs = 0;
+
+ // send a command
+ _spi.write(0x40 | cmd);
+ _spi.write(arg >> 24);
+ _spi.write(arg >> 16);
+ _spi.write(arg >> 8);
+ _spi.write(arg >> 0);
+ _spi.write(0x95);
+
+ // wait for the repsonse (response[7] == 0)
+ for(int i=0; i<SD_COMMAND_TIMEOUT; i++) {
+ int response = _spi.write(0xFF);
+ if(!(response & 0x80)) {
+ _cs = 1;
+ _spi.write(0xFF);
+ return response;
+ }
+ }
+ _cs = 1;
+ _spi.write(0xFF);
+ return -1; // timeout
+}
+int SDFileSystem::_cmdx(int cmd, int arg) {
+ _cs = 0;
+
+ // send a command
+ _spi.write(0x40 | cmd);
+ _spi.write(arg >> 24);
+ _spi.write(arg >> 16);
+ _spi.write(arg >> 8);
+ _spi.write(arg >> 0);
+ _spi.write(0x95);
+
+ // wait for the repsonse (response[7] == 0)
+ for(int i=0; i<SD_COMMAND_TIMEOUT; i++) {
+ int response = _spi.write(0xFF);
+ if(!(response & 0x80)) {
+ return response;
+ }
+ }
+ _cs = 1;
+ _spi.write(0xFF);
+ return -1; // timeout
+}
+
+
+int SDFileSystem::_cmd58() {
+ _cs = 0;
+ int arg = 0;
+
+ // send a command
+ _spi.write(0x40 | 58);
+ _spi.write(arg >> 24);
+ _spi.write(arg >> 16);
+ _spi.write(arg >> 8);
+ _spi.write(arg >> 0);
+ _spi.write(0x95);
+
+ // wait for the repsonse (response[7] == 0)
+ for(int i=0; i<SD_COMMAND_TIMEOUT; i++) {
+ int response = _spi.write(0xFF);
+ if(!(response & 0x80)) {
+ int ocr = _spi.write(0xFF) << 24;
+ ocr |= _spi.write(0xFF) << 16;
+ ocr |= _spi.write(0xFF) << 8;
+ ocr |= _spi.write(0xFF) << 0;
+// printf("OCR = 0x%08X\n", ocr);
+ _cs = 1;
+ _spi.write(0xFF);
+ return response;
+ }
+ }
+ _cs = 1;
+ _spi.write(0xFF);
+ return -1; // timeout
+}
+
+int SDFileSystem::_cmd8() {
+ _cs = 0;
+
+ // send a command
+ _spi.write(0x40 | 8); // CMD8
+ _spi.write(0x00); // reserved
+ _spi.write(0x00); // reserved
+ _spi.write(0x01); // 3.3v
+ _spi.write(0xAA); // check pattern
+ _spi.write(0x87); // crc
+
+ // wait for the repsonse (response[7] == 0)
+ for(int i=0; i<SD_COMMAND_TIMEOUT * 1000; i++) {
+ char response[5];
+ response[0] = _spi.write(0xFF);
+ if(!(response[0] & 0x80)) {
+ for(int j=1; j<5; j++) {
+ response[i] = _spi.write(0xFF);
+ }
+ _cs = 1;
+ _spi.write(0xFF);
+ return response[0];
+ }
+ }
+ _cs = 1;
+ _spi.write(0xFF);
+ return -1; // timeout
+}
+
+int SDFileSystem::_read(char *buffer, int length) {
+ _cs = 0;
+
+ // read until start byte (0xFF)
+ while(_spi.write(0xFF) != 0xFE);
+
+ // read data
+ for(int i=0; i<length; i++) {
+ buffer[i] = _spi.write(0xFF);
+ }
+ _spi.write(0xFF); // checksum
+ _spi.write(0xFF);
+
+ _cs = 1;
+ _spi.write(0xFF);
+ return 0;
+}
+
+int SDFileSystem::_write(const char *buffer, int length) {
+ _cs = 0;
+
+ // indicate start of block
+ _spi.write(0xFE);
+
+ // write the data
+ for(int i=0; i<length; i++) {
+ _spi.write(buffer[i]);
+ }
+
+ // write the checksum
+ _spi.write(0xFF);
+ _spi.write(0xFF);
+
+ // check the repsonse token
+ if((_spi.write(0xFF) & 0x1F) != 0x05) {
+ _cs = 1;
+ _spi.write(0xFF);
+ return 1;
+ }
+
+ // wait for write to finish
+ while(_spi.write(0xFF) == 0);
+
+ _cs = 1;
+ _spi.write(0xFF);
+ return 0;
+}
+
+static int ext_bits(char *data, int msb, int lsb) {
+ int bits = 0;
+ int size = 1 + msb - lsb;
+ for(int i=0; i<size; i++) {
+ int position = lsb + i;
+ int byte = 15 - (position >> 3);
+ int bit = position & 0x7;
+ int value = (data[byte] >> bit) & 1;
+ bits |= value << i;
+ }
+ return bits;
+}
+
+int SDFileSystem::_sd_sectors() {
+
+ // CMD9, Response R2 (R1 byte + 16-byte block read)
+ if(_cmdx(9, 0) != 0) {
+ fprintf(stderr, "Didn't get a response from the disk\n");
+ return 0;
+ }
+
+ char csd[16];
+ if(_read(csd, 16) != 0) {
+ fprintf(stderr, "Couldn't read csd response from disk\n");
+ return 0;
+ }
+
+ // csd_structure : csd[127:126]
+ // c_size : csd[73:62]
+ // c_size_mult : csd[49:47]
+ // read_bl_len : csd[83:80] - the *maximum* read block length
+
+ int csd_structure = ext_bits(csd, 127, 126);
+ int c_size = ext_bits(csd, 73, 62);
+ int c_size_mult = ext_bits(csd, 49, 47);
+ int read_bl_len = ext_bits(csd, 83, 80);
+
+// printf("CSD_STRUCT = %d\n", csd_structure);
+
+ if(csd_structure != 0) {
+ fprintf(stderr, "This disk tastes funny! I only know about type 0 CSD structures\n");
+ return 0;
+ }
+
+ // memory capacity = BLOCKNR * BLOCK_LEN
+ // where
+ // BLOCKNR = (C_SIZE+1) * MULT
+ // MULT = 2^(C_SIZE_MULT+2) (C_SIZE_MULT < 8)
+ // BLOCK_LEN = 2^READ_BL_LEN, (READ_BL_LEN < 12)
+
+ int block_len = 1 << read_bl_len;
+ int mult = 1 << (c_size_mult + 2);
+ int blocknr = (c_size + 1) * mult;
+ int capacity = blocknr * block_len;
+
+ int blocks = capacity / 512;
+
+ return blocks;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/SDFileSystem/SDFileSystem.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,81 @@
+/* mbed SDFileSystem Library, for providing file access to SD cards
+ * Copyright (c) 2008-2010, sford
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#ifndef MBED_SDFILESYSTEM_H
+#define MBED_SDFILESYSTEM_H
+
+#include "mbed.h"
+#include "FATFileSystem.h"
+
+/** Access the filesystem on an SD Card using SPI
+ *
+ * @code
+ * #include "mbed.h"
+ * #include "SDFileSystem.h"
+ *
+ * SDFileSystem sd(p5, p6, p7, p12, "sd"); // mosi, miso, sclk, cs
+ *
+ * int main() {
+ * FILE *fp = fopen("/sd/myfile.txt", "w");
+ * fprintf(fp, "Hello World!\n");
+ * fclose(fp);
+ * }
+ */
+class SDFileSystem : public FATFileSystem {
+public:
+
+ /** Create the File System for accessing an SD Card using SPI
+ *
+ * @param mosi SPI mosi pin connected to SD Card
+ * @param miso SPI miso pin conencted to SD Card
+ * @param sclk SPI sclk pin connected to SD Card
+ * @param cs DigitalOut pin used as SD Card chip select
+ * @param name The name used to access the virtual filesystem
+ */
+ SDFileSystem(PinName mosi, PinName miso, PinName sclk, PinName cs, const char* name);
+ virtual int disk_initialize();
+ virtual int disk_write(const char *buffer, int block_number);
+ virtual int disk_read(char *buffer, int block_number);
+ virtual int disk_status();
+ virtual int disk_sync();
+ virtual int disk_sectors();
+
+protected:
+
+ int _cmd(int cmd, int arg);
+ int _cmdx(int cmd, int arg);
+ int _cmd8();
+ int _cmd58();
+ int initialise_card();
+ int initialise_card_v1();
+ int initialise_card_v2();
+
+ int _read(char *buffer, int length);
+ int _write(const char *buffer, int length);
+ int _sd_sectors();
+ int _sectors;
+
+ SPI _spi;
+ DigitalOut _cs;
+};
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,543 @@
+#include "mbed.h"
+
+//set up the message buffer to be filled by the GPS read process
+#define MODSERIAL_DEFAULT_RX_BUFFER_SIZE 256
+
+#include "MODSERIAL.h"
+#include "SDFileSystem.h" //imported using the import utility
+//#include "rtos.h"
+#include "OEM615.h"
+
+#include "ADIS16488.h"
+#include <string>
+
+#define STATUS_MSG 0
+#define POSVEL_MSG 1
+#define STARTDATA_MSG 2
+#define STOPDATA_MSG 3
+#define STARTSTREAM_MSG 4
+#define STOPSTREAM_MSG 5
+#define DEGREES_TO_RADIANS (3.14519/180.0)
+
+//general items for this application
+//SDFileSystem(PinName mosi, PinName miso, PinName sclk, PinName cs, const char* name);
+SDFileSystem sd(p11,p12,p13,p14,"sd");
+//Serial debug(USBTX, USBRX); // tx, rx USB communication to the PC for debug purposes
+DigitalOut ppsled(LED1);
+DigitalOut trig1led(LED2);
+DigitalOut recordDataled(LED4);
+InterruptIn Camera1Int(p30);
+InterruptIn Camera2Int(p29);
+//USB serial data stream back to the PC
+Serial toPC(USBTX, USBRX); //connect the GPS TX, RX to p9 and p10
+
+bool detectedGPS1PPS = false;
+bool recordData = false;
+int PPSCounter = 0;
+int byteCounter = 0;
+unsigned short perSecMessageCounter=0;
+bool lookingForMessages = true;
+bool messageDetected = false;
+int savedIMUClockCounter=0;
+int IMUClockCounter = 0;
+bool camera1EventDetected = false;
+bool camera2EventDetected = false;
+double camera1Time;
+double camera2Time;
+char serBuf[64];
+int serBufChars=0;
+bool sendPosVel=false;
+bool sendStatus=false;
+bool sendRecData=false;
+bool streamPos=false;
+bool sendStreamPos=false;
+
+
+//ISR for detection of the GPS 1PPS
+void detect1PPSISR(void)
+{
+ timeFromPPS.reset();
+ savedIMUClockCounter = IMUClockCounter;
+ IMUClockCounter = 0;
+ GPS_COM1.rxBufferFlush();
+
+ //byteCounter=0;
+ detectedGPS1PPS = true;
+ lookingForMessages = true;
+ PPSCounter++;
+ PPSTimeOffset++;
+ ppsled = !ppsled;
+};
+
+//ISR for detection of the hotshoe trigger 1
+void Camera1ISR(void)
+{
+ camera1Time = GPSTime + (double)PPSTimeOffset + timeFromPPS.read();
+ //detectedTrigger1 = true;
+ trig1led = !trig1led;
+ camera1EventDetected = true;
+};
+//ISR for detection of the hotshoe trigger 2
+void Camera2ISR(void)
+{
+ camera2Time = GPSTime + (double)PPSTimeOffset + timeFromPPS.read();
+ //detectedTrigger1 = true;
+ camera2EventDetected = true;
+};
+
+void readFromPC()
+{
+ if (toPC.readable()) //read a PC serial byte and test it for a command
+ {
+ // Read in next character
+ char inChar = toPC.getc();
+ serBuf[serBufChars++] = inChar;
+ // Append end of string character
+ serBuf[serBufChars] = '\0';
+ // Need to parse message to determine behavior
+ // Need to clean this up
+ char msgList[6][32];
+ sprintf(msgList[STATUS_MSG], "WMsg STATUS");
+ sprintf(msgList[POSVEL_MSG], "WMsg POSVEL");
+ sprintf(msgList[STARTDATA_MSG], "WMsg RECORDDATA Y");
+ sprintf(msgList[STOPDATA_MSG], "WMsg RECORDDATA N");
+ sprintf(msgList[STARTSTREAM_MSG], "WMsg POSSTREAM Y");
+ sprintf(msgList[STOPSTREAM_MSG], "WMsg POSSTREAM N");
+ // assume an invalid message which needs to be reset
+ bool validMessage = false;
+ bool resetMessage = true;
+ // Check for valid message
+ for (int m = 0; m < 6 && !validMessage; m++)
+ {
+ if (strncmp(serBuf, msgList[m], serBufChars) == 0)
+ {
+ validMessage = true;
+ // buffer length is same as message length
+ if (serBufChars == strlen(msgList[m]))
+ {
+ switch(m)
+ {
+ case STATUS_MSG:
+ sendStatus = true;
+ break;
+ case POSVEL_MSG:
+ sendPosVel = true;
+ break;
+ case STARTDATA_MSG:
+ case STOPDATA_MSG:
+ recordData = (m == STARTDATA_MSG);
+ sendRecData = true;
+ break;
+ case STARTSTREAM_MSG:
+ case STOPSTREAM_MSG:
+ streamPos = (m == STARTSTREAM_MSG);
+ sendStreamPos = true;
+ break;
+
+ }
+ }
+ // message is still in progress, do not reset
+ else
+ {
+ resetMessage = false;
+ }
+ }
+ }
+ // if message should be reset
+ if (resetMessage)
+ {
+ // reset serial buffer character count
+ serBufChars = 0;
+ // if invalid message and most recent character is 'W' (first message character),
+ // possible message collision
+ if ((!validMessage) && (inChar == 'W'))
+ {
+ // start a new message
+ serBuf[serBufChars++] = inChar;
+ serBuf[serBufChars] == '\0';
+ }
+ // Append end of string character
+ serBuf[serBufChars] = '\0';
+ }
+ }
+};
+
+void sendASCII(char* ASCI_message, int numChars)
+{
+ //char ASCI_message[] = "unlogall COM1";
+ int as = numChars - 1;
+ unsigned char CR = 0x0d; //ASCII Carriage Return
+ unsigned char LF = 0x0a; //ASCII Line Feed
+
+ //printf("%s", ch);
+ //printf("\n");
+
+ for (int i=0; i<as; i++) GPS_COM1.putc(ASCI_message[i]);
+ GPS_COM1.putc(CR); //carriage return at end
+ GPS_COM1.putc(LF); //line feed at end
+}
+
+//FILE* fp = NULL;
+void setupCOM(void)
+{
+ //system starts with GPS in reset active
+ //dis-engage the reset to get the GPS started
+ GPS_Reset=1; wait_ms(1000);
+
+ //establish 1PPS ISR
+ PPSInt.rise(&detect1PPSISR);
+
+ //set the USB serial data rate -- rate must be matched at the PC end
+ //This the serial communication back to the the PC host
+ //Launch the C++ serial port read program there to catch the ASCII characters
+ //toPC.baud(9600); wait_ms(100);
+ toPC.baud(8*115200); wait_ms(100);
+ toPC.printf("\n\n released GPS from RESET and set to high baud rate \n\n");
+
+ //just wait to lauinch the GPS receiver
+ for (int i=0; i<5; i++) { toPC.printf(" to start: %3d \n", 4-i); wait(1); }
+
+
+ mkdir("/sd/Data", 0777);
+
+ /*
+ fp = fopen("/sd/Data/IMUGPS.bin", "wb");
+ if (fp == NULL)
+ {
+ toPC.printf(" cannot open the IMUGPS data file \n");
+ }
+ else
+ toPC.printf(" opened the IMUGPS data file \n");
+ */
+
+ //this is the COM1 port from th GPS receiuver to the mbed
+ //it should be always started at 9600 baud because thats the default for the GPS receiver
+ GPS_COM1.baud(9600); wait_ms(100);
+
+ // this ASCII command sets up the serial data from the GPS receiver on its COM1
+ char ch7[] = "serialconfig COM1 9600 n 8 1 n off";
+ // this is a software reset and has the same effect as a hardware reset (why do it??)
+ char ch0[] = "RESET";
+ //this command stops all communication from the GPS receiver on COM1
+ //logs should still be presented on USB port so the CDU can be used in parallel
+ char ch1[] = "unlogall COM1";
+ //set the final baud rate that we will use from here
+ //allowable baud rate values: 9600 115200 230400 460800 921600
+ char ch2[] = "serialconfig COM1 921600 n 8 1 n off";
+
+ //the below commands request the POS, VEL, RANGE, and TIME messages
+ char ch3[] = "log COM1 BESTPOSB ONTIME 1"; //messageID = 42
+ char ch4[] = "log COM1 BESTVelB ONTIME 1"; //messageID = 99
+ char ch5[] = "log COM1 RANGEB ONTIME 1"; //messageID = 43
+ char ch6[] = "log COM1 TIMEB ONTIME 1"; //messageID = 101
+
+ //set up VARF to be 100Hz with 1X10^4 * 10^-8 = 10^-4 sec (10usec) pulse width
+ char ch8[] = "FREQUENCYOUT enable 10000 1000000";
+
+ toPC.printf("set serial config \n");
+ sendASCII(ch7, sizeof(ch7)); wait_ms(500);
+ //sendASCII(ch0, sizeof(ch0));
+ toPC.printf("unlog all messages \n");
+ sendASCII(ch1, sizeof(ch1)); wait_ms(500);
+ toPC.printf("log BESTPOSB on COM1 \n");
+ sendASCII(ch3, sizeof(ch3)); wait_ms(500);
+ toPC.printf("log BESTVELB on COM1\n");
+ sendASCII(ch4, sizeof(ch4)); wait_ms(500);
+ toPC.printf("log RANGEB on COM1\n");
+ sendASCII(ch5, sizeof(ch5)); wait_ms(500);
+
+ //toPC.printf("log TIMEB om COM1 \n");
+ //sendASCII(ch6, sizeof(ch6)); wait_ms(100);
+
+ toPC.printf(" set up th VARF signal \n");
+ sendASCII(ch8, sizeof(ch8)); wait_ms(500);
+
+ //set GPS output COM1 to the final high rate
+ toPC.printf("set the COM ports to high rate\n");
+ sendASCII(ch2, sizeof(ch2)); wait_ms(500);
+
+ //set the mbed COM port to match the GPS transmit rate
+ //the below baud rate must match the COM1 rate coming from the GPS receiver
+ GPS_COM1.baud(921600); wait_ms(500); //without this wait -- the baud rate is not detected when using MODSERIAL
+};
+
+void setupTriggers()
+{
+ Camera1Int.mode(PullUp);
+ Camera2Int.mode(PullUp);
+ //establish Trigger ISR
+ Camera1Int.rise(&Camera1ISR);
+ Camera2Int.rise(&Camera2ISR);
+
+}
+
+int test = 0;
+unsigned short messageCounter = 0;
+unsigned short savedMessageCounter = 0;
+unsigned char msgBuffer[1024];
+unsigned short messageLocation[4] = {0};
+
+//see the mbed COOKBOOK for MODSERIAL
+//MODSERIAL is an easy to use library that extends Serial to add fully buffered input and output.
+void readSerialByte(MODSERIAL_IRQ_INFO *q)
+{
+ MODSERIAL *serial = q->serial;
+ unsigned char synch0 = serial->getc();
+ msgBuffer[byteCounter] = synch0;
+
+ //we need to trap the GPS message header byte-string 0xAA44121C
+ //generate a 4-byte sliding-window sequence from the input bytes
+ //shift last 4-byte value left 8 bits & push recently read byte (synch0) into low-order byte
+ test = (test<<8) | synch0; //
+
+ if (test == 0xAA44121C) //test for the Receiver message header signature
+ {
+ messageLocation[perSecMessageCounter] = byteCounter; //store the location of this message (with 4 synch words)
+ perSecMessageCounter++;
+ messageDetected = true;
+ }
+ byteCounter++; //total per-sec byte counter (reset to zero in main when 1PPS detected)
+
+};
+
+int main() {
+
+ //FILE *fpIMU = NULL;
+ //FILE *fpGPS = NULL;
+ FILE *fpNav = NULL;
+ OEM615BESTPOS posMsg;
+ OEM615BESTPOS curPos;
+ OEM615BESTVEL velMsg;
+ OEM615BESTVEL curVel;
+
+ //set up th GPS and mbed COM ports
+ setupCOM();
+
+ //set up the ADIS16488
+ setupADIS();
+
+ //setup Hotshoe
+ setupTriggers();
+ //attempt to use the mbed RTOS library
+ //Thread thread(writeThread);
+
+ toPC.printf("completed setting up COM ports \n");
+
+ //set up the interrupt to catch the serial byte availability
+ GPS_COM1.attach(&readSerialByte, MODSERIAL::RxIrq);
+
+ timeFromPPS.start();
+
+ //while(PPSCounter < 1000)
+ while(1)
+ {
+ //read the USB serial data from the PC to check for commands
+ readFromPC();
+
+ if (sendPosVel)
+ {
+ sendPosVel=false;
+ char solReady = 'N';
+ if (posMsg.solStatus == 0)
+ {
+ solReady = 'Y';
+ }
+ double nVel = velMsg.horizontalSpeed*cos(velMsg.heading*DEGREES_TO_RADIANS);
+ double eVel = velMsg.horizontalSpeed*sin(velMsg.heading*DEGREES_TO_RADIANS);
+ // For the 1 second deltas with which we are dealing
+ // this calculation should be close enough for now
+ // approximately 1 nautical mile / minute latitude, 60 minutes/degree, 1852 meters/nautical mile
+ double latMetersPerDeg = 60.0*1852.0;
+ // longitude separation is approximately equal to latitude separation * cosine of latitude
+ double lonMetersPerDeg = latMetersPerDeg*cos(posMsg.latitude*DEGREES_TO_RADIANS);
+
+ // Elapsed time since last known GPS position
+ double elTime = (double)PPSTimeOffset + timeFromPPS.read();
+ // Position time
+ double posTime = GPSTime + elTime;
+
+ // Estimated position based on previous position and velocity
+ double latPos = posMsg.latitude + (nVel/latMetersPerDeg)*elTime;
+ double lonPos = posMsg.longitude + (eVel/lonMetersPerDeg)*elTime;
+ double htPos = posMsg.height + velMsg.verticalSpeed/(60*1852)*elTime;
+ toPC.printf("WMsg POSVEL %5.3lf %d %c %8.5lf %9.5lf %4.3lf %4.3lf %4.3lf %4.3lf\n",
+ posTime,
+ posMsg.numSolSV,
+ solReady,
+ latPos,
+ lonPos,
+ htPos,
+ nVel,
+ eVel,
+ velMsg.verticalSpeed
+ );
+ }
+ if (sendStatus)
+ {
+ sendStatus=false;
+ char solReady = 'N';
+ if (posMsg.solStatus == 0)
+ {
+ solReady = 'Y';
+ }
+ toPC.printf("WMsg STATUS %5.3lf %c\n",
+ GPSTime,
+ solReady
+ );
+ }
+ if (sendRecData)
+ {
+ sendRecData=false;
+ char recChar = 'N';
+ if (recordData)
+ {
+ if ((fpNav == NULL))
+ {
+ fpNav = fopen("/sd/Data/NAV.bin", "wb");
+ }
+ if (fpNav != NULL)
+ {
+ recChar = 'Y';
+ }
+ //recChar = 'Y';
+ }
+ else
+ {
+ if (fpNav != NULL)
+ {
+ fclose(fpNav);
+ fpNav = NULL;
+ }
+ /*
+ if (fpIMU != NULL)
+ {
+ fclose(fpIMU);
+ fpIMU = NULL;
+ }
+ if (fpGPS != NULL)
+ {
+ fclose(fpGPS);
+ fpGPS = NULL;
+ }
+ */
+ }
+ toPC.printf("WMsg RECORDDATA %c\n",
+ recChar
+ );
+ }
+ recordDataled = recordData;
+ if (sendStreamPos)
+ {
+ sendStreamPos=false;
+ char streamChar = 'N';
+ if (streamPos)
+ {
+ streamChar = 'Y';
+ }
+ toPC.printf("WMsg POSSTREAM %c\n",
+ streamChar
+ );
+ }
+ if (IMUDataReady)
+ {
+ //write the IMU data
+ //if (recordData && (fpIMU != NULL))
+ if (recordData && (fpNav != NULL))
+ {
+ fwrite(imuRec.dataWord, sizeof(IMUREC), 1, fpNav);
+ }
+ IMUDataReady = false;
+ }
+ if (lookingForMessages && (timeFromPPS.read_us() > 15000)) //it takes less than 20msec to receive all messages
+ {
+
+ //toPC.printf(" num messages = %3d time = %5d \n", perSecMessageCounter, timeFromPPS.read_us());
+ for (int i=0; i<perSecMessageCounter; i++)
+ {
+ msgHeader[i] = (MESSAGEHEADER*)&msgBuffer[messageLocation[i]-3];
+ //toPC.printf(" %5d ", msgHeader[i]->messageID);
+ if ((msgHeader[i]->messageID == 42) ||
+ (msgHeader[i]->messageID == 99))
+ {
+ if (msgHeader[i]->messageID == 42)
+ {
+ // Wait until velocity message has also been received before using as
+ // base position
+ //memcpy(&curPos, &msgBuffer[messageLocation[i]-3], sizeof(OEM615BESTPOS));
+ curPos = *((OEM615BESTPOS*)&msgBuffer[messageLocation[i]-3]);
+ if (streamPos)
+ {
+ toPC.printf("WMsg BESTPOS %d %d %d %8.5lf %9.5lf %5.3lf %5.3f %5.3f %5.3f %5.3f %5.3f %5.3f %d %d %d %d %d\n",
+ curPos.msgHeader.GPSTime_msecs,
+ curPos.solStatus,
+ curPos.posType,
+ curPos.latitude,
+ curPos.longitude,
+ curPos.height,
+ curPos.undulation,
+ curPos.latitudeSTD,
+ curPos.longitudeSTD,
+ curPos.heightSTD,
+ curPos.diffAge,
+ curPos.solutionAge,
+ curPos.numSV,
+ curPos.numSolSV,
+ curPos.numGGL1,
+ curPos.extSolStatus,
+ curPos.sigMask);
+ }
+ }
+ else if (msgHeader[i]->messageID == 99)
+ {
+ // Wait until position message has also been received before using as
+ // base position
+ //memcpy(&curVel, &msgBuffer[messageLocation[i]-3], sizeof(OEM615BESTVEL));
+ curVel = *((OEM615BESTVEL*)&msgBuffer[messageLocation[i]-3]);
+ }
+ if ((curVel.msgHeader.GPSTime_msecs+250)/1000 ==
+ (curPos.msgHeader.GPSTime_msecs+250)/1000)
+ {
+ // update position and velocity used for calculation
+ GPSTimemsecs = curPos.msgHeader.GPSTime_msecs;
+ GPSTime = (double)GPSTimemsecs/1000.0;
+ velMsg = curVel;
+ posMsg = curPos;
+ PPSTimeOffset = 0;
+ }
+ }
+ }
+ //toPC.printf(" %3d %8d \n", msgHeader[0]->timeStatus, GPSTimemsecs);
+ //if (recordData && (fpGPS != NULL))
+ if (recordData && (fpNav != NULL))
+ {
+ fwrite(msgBuffer, byteCounter, 1, fpNav);
+ }
+
+ lookingForMessages = false;
+ }
+ if (messageDetected)
+ {
+ //toPC.printf(" msgTime = %4d \n", timeFromPPS.read_us());
+ messageDetected = false;
+ }
+ if (camera1EventDetected)
+ {
+ toPC.printf("WMsg TRIGGERTIME Camera1 %5.3lf\n", camera1Time);
+ camera1EventDetected = false;
+ }
+ if (camera2EventDetected)
+ {
+ toPC.printf("WMsg TRIGGERTIME Camera2 %5.3lf\n", camera2Time);
+ camera2EventDetected = false;
+ }
+ if (detectedGPS1PPS)
+ {
+ //toPC.printf(" PPSCounter = %4d byteCounter = %10d num Messages Received = %3d IMUClock = %4d\n",
+ // PPSCounter, byteCounter, perSecMessageCounter, savedIMUClockCounter);
+ byteCounter = 0;
+ perSecMessageCounter=0;
+ detectedGPS1PPS = false;
+ }
+ }
+ toPC.printf(" normal termination \n");
+}
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtos.lib Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,1 @@ +http://mbed.org/users/mbed_official/code/rtos/#68e146c0e76b
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Mail.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,89 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef MAIL_H
+#define MAIL_H
+
+#include <stdint.h>
+#include <string.h>
+
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! The Mail class allow to control, send, receive, or wait for mail.
+ A mail is a memory block that is send to a thread or interrupt service routine.
+ \tparam T data type of a single message element.
+ \tparam queue_sz maximum number of messages in queue.
+*/
+template<typename T, uint32_t queue_sz>
+class Mail {
+public:
+ /*! Create and Initialise Mail queue. */
+ Mail() {
+ #ifdef CMSIS_OS_RTX
+ memset(_mail_q, 0, sizeof(_mail_q));
+ _mail_p[0] = _mail_q;
+
+ memset(_mail_m, 0, sizeof(_mail_m));
+ _mail_p[1] = _mail_m;
+
+ _mail_def.pool = _mail_p;
+ _mail_def.queue_sz = queue_sz;
+ _mail_def.item_sz = sizeof(T);
+ #endif
+ _mail_id = osMailCreate(&_mail_def, NULL);
+ }
+
+ /*! Allocate a memory block of type T
+ \param millisec timeout value or 0 in case of no time-out. (default: 0).
+ \return pointer to memory block that can be filled with mail or NULL in case error.
+ */
+ T* alloc(uint32_t millisec=0) {
+ return (T*)osMailAlloc(_mail_id, millisec);
+ }
+
+ /*! Allocate a memory block of type T and set memory block to zero.
+ \param millisec timeout value or 0 in case of no time-out. (default: 0).
+ \return pointer to memory block that can be filled with mail or NULL in case error.
+ */
+ T* calloc(uint32_t millisec=0) {
+ return (T*)osMailCAlloc(_mail_id, millisec);
+ }
+
+ /*! Put a mail in the queue.
+ \param mptr memory block previously allocated with Mail::alloc or Mail::calloc.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus put(T *mptr) {
+ return osMailPut(_mail_id, (void*)mptr);
+ }
+
+ /*! Get a mail from a queue.
+ \param millisec timeout value or 0 in case of no time-out. (default: osWaitForever).
+ \return event that contains mail information or error code.
+ */
+ osEvent get(uint32_t millisec=osWaitForever) {
+ return osMailGet(_mail_id, millisec);
+ }
+
+ /*! Free a memory block from a mail.
+ \param mptr pointer to the memory block that was obtained with Mail::get.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus free(T *mptr) {
+ return osMailFree(_mail_id, (void*)mptr);
+ }
+
+private:
+ osMailQId _mail_id;
+ osMailQDef_t _mail_def;
+#ifdef CMSIS_OS_RTX
+ uint32_t _mail_q[4+(queue_sz)];
+ uint32_t _mail_m[3+((sizeof(T)+3)/4)*(queue_sz)];
+ void *_mail_p[2];
+#endif
+};
+
+}
+
+#endif
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/MemoryPool.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,62 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef MEMORYPOOL_H
+#define MEMORYPOOL_H
+
+#include <stdint.h>
+#include <string.h>
+
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! Define and manage fixed-size memory pools of objects of a given type.
+ \tparam T data type of a single object (element).
+ \tparam queue_sz maximum number of objects (elements) in the memory pool.
+*/
+template<typename T, uint32_t pool_sz>
+class MemoryPool {
+public:
+ /*! Create and Initialize a memory pool. */
+ MemoryPool() {
+ #ifdef CMSIS_OS_RTX
+ memset(_pool_m, 0, sizeof(_pool_m));
+ _pool_def.pool = _pool_m;
+
+ _pool_def.pool_sz = pool_sz;
+ _pool_def.item_sz = sizeof(T);
+ #endif
+ _pool_id = osPoolCreate(&_pool_def);
+ }
+
+ /*! Allocate a memory block of type T from a memory pool.
+ \return address of the allocated memory block or NULL in case of no memory available.
+ */
+ T* alloc(void) {
+ return (T*)osPoolAlloc(_pool_id);
+ }
+
+ /*! Allocate a memory block of type T from a memory pool and set memory block to zero.
+ \return address of the allocated memory block or NULL in case of no memory available.
+ */
+ T* calloc(void) {
+ return (T*)osPoolCAlloc(_pool_id);
+ }
+
+ /*! Return an allocated memory block back to a specific memory pool.
+ \param address of the allocated memory block that is returned to the memory pool.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus free(T *block) {
+ return osPoolFree(_pool_id, (void*)block);
+ }
+
+private:
+ osPoolId _pool_id;
+ osPoolDef_t _pool_def;
+#ifdef CMSIS_OS_RTX
+ uint32_t _pool_m[3+((sizeof(T)+3)/4)*(pool_sz)];
+#endif
+};
+
+}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Mutex.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,35 @@
+#include "Mutex.h"
+
+#include <string.h>
+#include "error.h"
+
+namespace rtos {
+
+Mutex::Mutex() {
+#ifdef CMSIS_OS_RTX
+ memset(_mutex_data, 0, sizeof(_mutex_data));
+ _osMutexDef.mutex = _mutex_data;
+#endif
+ _osMutexId = osMutexCreate(&_osMutexDef);
+ if (_osMutexId == NULL) {
+ error("Error initializing the mutex object\n");
+ }
+}
+
+osStatus Mutex::lock(uint32_t millisec) {
+ return osMutexWait(_osMutexId, millisec);
+}
+
+bool Mutex::trylock() {
+ return (osMutexWait(_osMutexId, 0) == osOK);
+}
+
+osStatus Mutex::unlock() {
+ return osMutexRelease(_osMutexId);
+}
+
+Mutex::~Mutex() {
+ osMutexDelete(_osMutexId);
+}
+
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Mutex.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,45 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef MUTEX_H
+#define MUTEX_H
+
+#include <stdint.h>
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! The Mutex class is used to synchronise the execution of threads.
+ This is for example used to protect access to a shared resource.
+*/
+class Mutex {
+public:
+ /*! Create and Initialize a Mutex object */
+ Mutex();
+
+ /*! Wait until a Mutex becomes available.
+ \param millisec timeout value or 0 in case of no time-out. (default: osWaitForever)
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus lock(uint32_t millisec=osWaitForever);
+
+ /*! Try to lock the mutex, and return immediately
+ \return true if the mutex was acquired, false otherwise.
+ */
+ bool trylock();
+
+ /*! Unlock the mutex that has previously been locked by the same thread
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus unlock();
+
+ ~Mutex();
+
+private:
+ osMutexId _osMutexId;
+ osMutexDef_t _osMutexDef;
+#ifdef CMSIS_OS_RTX
+ int32_t _mutex_data[3];
+#endif
+};
+
+}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Queue.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,61 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef QUEUE_H
+#define QUEUE_H
+
+#include <stdint.h>
+#include <string.h>
+
+#include "cmsis_os.h"
+#include "error.h"
+
+namespace rtos {
+
+/*! The Queue class allow to control, send, receive, or wait for messages.
+ A message can be a integer or pointer value to a certain type T that is send
+ to a thread or interrupt service routine.
+ \tparam T data type of a single message element.
+ \tparam queue_sz maximum number of messages in queue.
+*/
+template<typename T, uint32_t queue_sz>
+class Queue {
+public:
+ /*! Create and initialise a message Queue. */
+ Queue() {
+ #ifdef CMSIS_OS_RTX
+ memset(_queue_q, 0, sizeof(_queue_q));
+ _queue_def.pool = _queue_q;
+ _queue_def.queue_sz = queue_sz;
+ #endif
+ _queue_id = osMessageCreate(&_queue_def, NULL);
+ if (_queue_id == NULL) {
+ error("Error initialising the queue object\n");
+ }
+ }
+
+ /*! Put a message in a Queue.
+ \param data message pointer.
+ \param millisec timeout value or 0 in case of no time-out. (default: 0)
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus put(T* data, uint32_t millisec=0) {
+ return osMessagePut(_queue_id, (uint32_t)data, millisec);
+ }
+
+ /*! Get a message or Wait for a message from a Queue.
+ \param millisec timeout value or 0 in case of no time-out. (default: osWaitForever).
+ \return event information that includes the message and the status code.
+ */
+ osEvent get(uint32_t millisec=osWaitForever) {
+ return osMessageGet(_queue_id, millisec);
+ }
+
+private:
+ osMessageQId _queue_id;
+ osMessageQDef_t _queue_def;
+#ifdef CMSIS_OS_RTX
+ uint32_t _queue_q[4+(queue_sz)];
+#endif
+};
+
+}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/RtosTimer.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,32 @@
+#include "RtosTimer.h"
+
+#include <string.h>
+
+#include "cmsis_os.h"
+#include "error.h"
+
+namespace rtos {
+
+RtosTimer::RtosTimer(void (*periodic_task)(void const *argument), os_timer_type type, void *argument) {
+#ifdef CMSIS_OS_RTX
+ _timer.ptimer = periodic_task;
+
+ memset(_timer_data, 0, sizeof(_timer_data));
+ _timer.timer = _timer_data;
+#endif
+ _timer_id = osTimerCreate(&_timer, type, argument);
+}
+
+osStatus RtosTimer::start(uint32_t millisec) {
+ return osTimerStart(_timer_id, millisec);
+}
+
+osStatus RtosTimer::stop(void) {
+ return osTimerStop(_timer_id);
+}
+
+RtosTimer::~RtosTimer() {
+ osTimerDelete(_timer_id);
+}
+
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/RtosTimer.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,51 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef TIMER_H
+#define TIMER_H
+
+#include <stdint.h>
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! The RtosTimer class allow creating and and controlling of timer functions in the system.
+ A timer function is called when a time period expires whereby both on-shot and
+ periodic timers are possible. A timer can be started, restarted, or stopped.
+
+ Timers are handled in the thread osTimerThread.
+ Callback functions run under control of this thread and may use CMSIS-RTOS API calls.
+*/
+class RtosTimer {
+public:
+ /*! Create and Start timer.
+ \param task name of the timer call back function.
+ \param type osTimerOnce for one-shot or osTimerPeriodic for periodic behaviour. (default: osTimerPeriodic)
+ \param argument argument to the timer call back function. (default: NULL)
+ */
+ RtosTimer(void (*task)(void const *argument),
+ os_timer_type type=osTimerPeriodic,
+ void *argument=NULL);
+
+ /*! Stop the timer.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus stop(void);
+
+ /*! start a timer.
+ \param millisec time delay value of the timer.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus start(uint32_t millisec);
+
+ ~RtosTimer();
+
+private:
+ osTimerId _timer_id;
+ osTimerDef_t _timer;
+#ifdef CMSIS_OS_RTX
+ uint32_t _timer_data[5];
+#endif
+};
+
+}
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Semaphore.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,28 @@
+#include "Semaphore.h"
+
+#include <string.h>
+#include "error.h"
+
+namespace rtos {
+
+Semaphore::Semaphore(int32_t count) {
+#ifdef CMSIS_OS_RTX
+ memset(_semaphore_data, 0, sizeof(_semaphore_data));
+ _osSemaphoreDef.semaphore = _semaphore_data;
+#endif
+ _osSemaphoreId = osSemaphoreCreate(&_osSemaphoreDef, count);
+}
+
+int32_t Semaphore::wait(uint32_t millisec) {
+ return osSemaphoreWait(_osSemaphoreId, millisec);
+}
+
+osStatus Semaphore::release(void) {
+ return osSemaphoreRelease(_osSemaphoreId);
+}
+
+Semaphore::~Semaphore() {
+ osSemaphoreDelete(_osSemaphoreId);
+}
+
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Semaphore.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,40 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef SEMAPHORE_H
+#define SEMAPHORE_H
+
+#include <stdint.h>
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! The Semaphore class is used to manage and protect access to a set of shared resources. */
+class Semaphore {
+public:
+ /*! Create and Initialize a Semaphore object used for managing resources.
+ \param number of available resources; maximum index value is (count-1).
+ */
+ Semaphore(int32_t count);
+
+ /*! Wait until a Semaphore resource becomes available.
+ \param millisec timeout value or 0 in case of no time-out. (default: osWaitForever).
+ \return number of available tokens, or -1 in case of incorrect parameters
+ */
+ int32_t wait(uint32_t millisec=osWaitForever);
+
+ /*! Release a Semaphore resource that was obtain with Semaphore::wait.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus release(void);
+
+ ~Semaphore();
+
+private:
+ osSemaphoreId _osSemaphoreId;
+ osSemaphoreDef_t _osSemaphoreDef;
+#ifdef CMSIS_OS_RTX
+ uint32_t _semaphore_data[2];
+#endif
+};
+
+}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Thread.cpp Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,58 @@
+#include "Thread.h"
+
+#include <stdlib.h>
+
+#include "error.h"
+
+namespace rtos {
+
+Thread::Thread(void (*task)(void const *argument), void *argument,
+ osPriority priority, uint32_t stack_size, unsigned char *stack_pointer) {
+#ifdef CMSIS_OS_RTX
+ _thread_def.pthread = task;
+ _thread_def.tpriority = priority;
+ _thread_def.stacksize = stack_size;
+ if (stack_pointer != NULL) {
+ _thread_def.stack_pointer = stack_pointer;
+ } else {
+ _thread_def.stack_pointer = (unsigned char*) malloc(stack_size);
+ if (_thread_def.stack_pointer == NULL)
+ error("Error allocating the stack memory");
+ }
+#endif
+ _tid = osThreadCreate(&_thread_def, argument);
+}
+
+osStatus Thread::terminate() {
+ return osThreadTerminate(_tid);
+}
+
+osStatus Thread::set_priority(osPriority priority) {
+ return osThreadSetPriority(_tid, priority);
+}
+
+osPriority Thread::get_priority() {
+ return osThreadGetPriority(_tid);
+}
+
+int32_t Thread::signal_set(int32_t signals) {
+ return osSignalSet(_tid, signals);
+}
+
+osEvent Thread::signal_wait(int32_t signals, uint32_t millisec) {
+ return osSignalWait(signals, millisec);
+}
+
+osStatus Thread::wait(uint32_t millisec) {
+ return osDelay(millisec);
+}
+
+osStatus Thread::yield() {
+ return osThreadYield();
+}
+
+osThreadId Thread::gettid() {
+ return osThreadGetId();
+}
+
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtos/Thread.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,77 @@
+/* Copyright (c) 2012 mbed.org */
+#ifndef THREAD_H
+#define THREAD_H
+
+#include <stdint.h>
+#include "cmsis_os.h"
+
+namespace rtos {
+
+/*! The Thread class allow defining, creating, and controlling thread functions in the system. */
+class Thread {
+public:
+ /*! Create a new thread, and start it executing the specified function.
+ \param task function to be executed by this thread.
+ \param argument pointer that is passed to the thread function as start argument. (default: NULL).
+ \param priority initial priority of the thread function. (default: osPriorityNormal).
+ \param stack_size stack size (in bytes) requirements for the thread function. (default: DEFAULT_STACK_SIZE).
+ \param stack_pointer pointer to the stack area to be used by this thread (default: NULL).
+ */
+ Thread(void (*task)(void const *argument), void *argument=NULL,
+ osPriority priority=osPriorityNormal,
+ uint32_t stack_size=DEFAULT_STACK_SIZE,
+ unsigned char *stack_pointer=NULL);
+
+ /*! Terminate execution of a thread and remove it from Active Threads
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus terminate();
+
+ /*! Set priority of an active thread
+ \param priority new priority value for the thread function.
+ \return status code that indicates the execution status of the function.
+ */
+ osStatus set_priority(osPriority priority);
+
+ /*! Get priority of an active thread
+ \ return current priority value of the thread function.
+ */
+ osPriority get_priority();
+
+ /*! Set the specified Signal Flags of an active thread.
+ \param signals specifies the signal flags of the thread that should be set.
+ \return previous signal flags of the specified thread or 0x80000000 in case of incorrect parameters.
+ */
+ int32_t signal_set(int32_t signals);
+
+ /*! Wait for one or more Signal Flags to become signaled for the current RUNNING thread.
+ \param signals wait until all specified signal flags set or 0 for any single signal flag.
+ \param millisec timeout value or 0 in case of no time-out. (default: osWaitForever).
+ \return event flag information or error code.
+ */
+ static osEvent signal_wait(int32_t signals, uint32_t millisec=osWaitForever);
+
+
+ /*! Wait for a specified time period in millisec:
+ \param millisec time delay value
+ \return status code that indicates the execution status of the function.
+ */
+ static osStatus wait(uint32_t millisec);
+
+ /*! Pass control to next thread that is in state READY.
+ \return status code that indicates the execution status of the function.
+ */
+ static osStatus yield();
+
+ /*! Get the thread id of the current running thread.
+ \return thread ID for reference by other functions or NULL in case of error.
+ */
+ static osThreadId gettid();
+
+private:
+ osThreadId _tid;
+ osThreadDef_t _thread_def;
+};
+
+}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtos/rtos.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,17 @@ +/* mbed Microcontroller Library + * Copyright (c) 2006-2012 ARM Limited. All rights reserved. + */ +#ifndef RTOS_H +#define RTOS_H + +#include "Thread.h" +#include "Mutex.h" +#include "RtosTimer.h" +#include "Semaphore.h" +#include "Mail.h" +#include "MemoryPool.h" +#include "Queue.h" + +using namespace rtos; + +#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx.lib Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,1 @@ +http://mbed.org/users/mbed_official/code/rtx/#77454ed243ca
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/HAL_CM.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,170 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: HAL_CM.C
+ * Purpose: Hardware Abstraction Layer for Cortex-M
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_HAL_CM.h"
+
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+#ifdef DBG_MSG
+BIT dbg_msg;
+#endif
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_init_stack ---------------------------------*/
+
+void rt_init_stack (P_TCB p_TCB, FUNCP task_body) {
+ /* Prepare TCB and saved context for a first time start of a task. */
+ U32 *stk,i,size;
+
+ /* Prepare a complete interrupt frame for first task start */
+ size = p_TCB->priv_stack >> 2;
+
+ /* Write to the top of stack. */
+ stk = &p_TCB->stack[size];
+
+ /* Auto correct to 8-byte ARM stack alignment. */
+ if ((U32)stk & 0x04) {
+ stk--;
+ }
+
+ stk -= 16;
+
+ /* Default xPSR and initial PC */
+ stk[15] = INITIAL_xPSR;
+ stk[14] = (U32)task_body;
+
+ /* Clear R4-R11,R0-R3,R12,LR registers. */
+ for (i = 0; i < 14; i++) {
+ stk[i] = 0;
+ }
+
+ /* Assign a void pointer to R0. */
+ stk[8] = (U32)p_TCB->msg;
+
+ /* Initial Task stack pointer. */
+ p_TCB->tsk_stack = (U32)stk;
+
+ /* Task entry point. */
+ p_TCB->ptask = task_body;
+
+ /* Set a magic word for checking of stack overflow.
+ For the main thread (ID: 0x01) the stack is in a memory area shared with the
+ heap, therefore the last word of the stack is a moving target.
+ We want to do stack/heap collision detection instead.
+ */
+ if (p_TCB->task_id != 0x01)
+ p_TCB->stack[0] = MAGIC_WORD;
+}
+
+
+/*--------------------------- rt_ret_val ----------------------------------*/
+
+static __inline U32 *rt_ret_regs (P_TCB p_TCB) {
+ /* Get pointer to task return value registers (R0..R3) in Stack */
+#if (__TARGET_FPU_VFP)
+ if (p_TCB->stack_frame) {
+ /* Extended Stack Frame: R4-R11,S16-S31,R0-R3,R12,LR,PC,xPSR,S0-S15,FPSCR */
+ return (U32 *)(p_TCB->tsk_stack + 8*4 + 16*4);
+ } else {
+ /* Basic Stack Frame: R4-R11,R0-R3,R12,LR,PC,xPSR */
+ return (U32 *)(p_TCB->tsk_stack + 8*4);
+ }
+#else
+ /* Stack Frame: R4-R11,R0-R3,R12,LR,PC,xPSR */
+ return (U32 *)(p_TCB->tsk_stack + 8*4);
+#endif
+}
+
+void rt_ret_val (P_TCB p_TCB, U32 v0) {
+ U32 *ret;
+
+ ret = rt_ret_regs(p_TCB);
+ ret[0] = v0;
+}
+
+void rt_ret_val2(P_TCB p_TCB, U32 v0, U32 v1) {
+ U32 *ret;
+
+ ret = rt_ret_regs(p_TCB);
+ ret[0] = v0;
+ ret[1] = v1;
+}
+
+
+/*--------------------------- dbg_init --------------------------------------*/
+
+#ifdef DBG_MSG
+void dbg_init (void) {
+ if ((DEMCR & DEMCR_TRCENA) &&
+ (ITM_CONTROL & ITM_ITMENA) &&
+ (ITM_ENABLE & (1UL << 31))) {
+ dbg_msg = __TRUE;
+ }
+}
+#endif
+
+/*--------------------------- dbg_task_notify -------------------------------*/
+
+#ifdef DBG_MSG
+void dbg_task_notify (P_TCB p_tcb, BOOL create) {
+ while (ITM_PORT31_U32 == 0);
+ ITM_PORT31_U32 = (U32)p_tcb->ptask;
+ while (ITM_PORT31_U32 == 0);
+ ITM_PORT31_U16 = (create << 8) | p_tcb->task_id;
+}
+#endif
+
+/*--------------------------- dbg_task_switch -------------------------------*/
+
+#ifdef DBG_MSG
+void dbg_task_switch (U32 task_id) {
+ while (ITM_PORT31_U32 == 0);
+ ITM_PORT31_U8 = task_id;
+}
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/LPC11U24/GCC_ARM/HAL_CM0.s Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,370 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: HAL_CM0.S
+ * Purpose: Hardware Abstraction Layer for Cortex-M0
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+ .file "HAL_CM0.S"
+ .syntax unified
+
+ .equ TCB_TSTACK, 36
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+ .thumb
+
+ .section ".text"
+ .align 2
+
+
+/*--------------------------- rt_set_PSP ------------------------------------*/
+
+# void rt_set_PSP (U32 stack);
+
+ .thumb_func
+ .type rt_set_PSP, %function
+ .global rt_set_PSP
+rt_set_PSP:
+ .fnstart
+ .cantunwind
+
+ MSR PSP,R0
+ BX LR
+
+ .fnend
+ .size rt_set_PSP, .-rt_set_PSP
+
+
+/*--------------------------- rt_get_PSP ------------------------------------*/
+
+# U32 rt_get_PSP (void);
+
+ .thumb_func
+ .type rt_get_PSP, %function
+ .global rt_get_PSP
+rt_get_PSP:
+ .fnstart
+ .cantunwind
+
+ MRS R0,PSP
+ BX LR
+
+ .fnend
+ .size rt_get_PSP, .-rt_get_PSP
+
+
+/*--------------------------- os_set_env ------------------------------------*/
+
+# void os_set_env (void);
+ /* Switch to Unprivileged/Privileged Thread mode, use PSP. */
+
+ .thumb_func
+ .type os_set_env, %function
+ .global os_set_env
+os_set_env:
+ .fnstart
+ .cantunwind
+
+ MOV R0,SP /* PSP = MSP */
+ MSR PSP,R0
+ LDR R0,=os_flags
+ LDRB R0,[R0]
+ LSLS R0,#31
+ BNE PrivilegedE
+ MOVS R0,#0x03 /* Unprivileged Thread mode, use PSP */
+ MSR CONTROL,R0
+ BX LR
+PrivilegedE:
+ MOVS R0,#0x02 /* Privileged Thread mode, use PSP */
+ MSR CONTROL,R0
+ BX LR
+
+ .fnend
+ .size os_set_env, .-os_set_env
+
+
+/*--------------------------- _alloc_box ------------------------------------*/
+
+# void *_alloc_box (void *box_mem);
+ /* Function wrapper for Unprivileged/Privileged mode. */
+
+ .thumb_func
+ .type _alloc_box, %function
+ .global _alloc_box
+_alloc_box:
+ .fnstart
+ .cantunwind
+
+ LDR R3,=rt_alloc_box
+ MOV R12,R3
+ MRS R3,IPSR
+ LSLS R3,#24
+ BNE PrivilegedA
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BEQ PrivilegedA
+ SVC 0
+ BX LR
+PrivilegedA:
+ BX R12
+
+ .fnend
+ .size _alloc_box, .-_alloc_box
+
+
+/*--------------------------- _free_box -------------------------------------*/
+
+# int _free_box (void *box_mem, void *box);
+ /* Function wrapper for Unprivileged/Privileged mode. */
+
+ .thumb_func
+ .type _free_box, %function
+ .global _free_box
+_free_box:
+ .fnstart
+ .cantunwind
+
+ LDR R3,=rt_free_box
+ MOV R12,R3
+ MRS R3,IPSR
+ LSLS R3,#24
+ BNE PrivilegedF
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BEQ PrivilegedF
+ SVC 0
+ BX LR
+PrivilegedF:
+ BX R12
+
+ .fnend
+ .size _free_box, .-_free_box
+
+
+/*-------------------------- SVC_Handler ------------------------------------*/
+
+# void SVC_Handler (void);
+
+ .thumb_func
+ .type SVC_Handler, %function
+ .global SVC_Handler
+SVC_Handler:
+ .fnstart
+ .cantunwind
+
+ MRS R0,PSP /* Read PSP */
+ LDR R1,[R0,#24] /* Read Saved PC from Stack */
+ SUBS R1,R1,#2 /* Point to SVC Instruction */
+ LDRB R1,[R1] /* Load SVC Number */
+ CMP R1,#0
+ BNE SVC_User /* User SVC Number > 0 */
+
+ MOV LR,R4
+ LDMIA R0,{R0-R3,R4} /* Read R0-R3,R12 from stack */
+ MOV R12,R4
+ MOV R4,LR
+ BLX R12 /* Call SVC Function */
+
+ MRS R3,PSP /* Read PSP */
+ STMIA R3!,{R0-R2} /* Store return values */
+
+ LDR R3,=os_tsk
+ LDMIA R3!,{R1,R2} /* os_tsk.run, os_tsk.new */
+ CMP R1,R2
+ BEQ SVC_Exit /* no task switch */
+
+ SUBS R3,#8
+ CMP R1,#0 /* Runtask deleted? */
+ BEQ SVC_Next
+
+ MRS R0,PSP /* Read PSP */
+ SUBS R0,R0,#32 /* Adjust Start Address */
+ STR R0,[R1,#TCB_TSTACK] /* Update os_tsk.run->tsk_stack */
+ STMIA R0!,{R4-R7} /* Save old context (R4-R7) */
+ MOV R4,R8
+ MOV R5,R9
+ MOV R6,R10
+ MOV R7,R11
+ STMIA R0!,{R4-R7} /* Save old context (R8-R11) */
+
+ PUSH {R2,R3}
+ BL rt_stk_check /* Check for Stack overflow */
+ POP {R2,R3}
+
+SVC_Next:
+ STR R2,[R3] /* os_tsk.run = os_tsk.new */
+
+ LDR R0,[R2,#TCB_TSTACK] /* os_tsk.new->tsk_stack */
+ ADDS R0,R0,#16 /* Adjust Start Address */
+ LDMIA R0!,{R4-R7} /* Restore new Context (R8-R11) */
+ MOV R8,R4
+ MOV R9,R5
+ MOV R10,R6
+ MOV R11,R7
+ MSR PSP,R0 /* Write PSP */
+ SUBS R0,R0,#32 /* Adjust Start Address */
+ LDMIA R0!,{R4-R7} /* Restore new Context (R4-R7) */
+
+SVC_Exit:
+ MOVS R0,#~0xFFFFFFFD /* Set EXC_RETURN value */
+ MVNS R0,R0
+ BX R0 /* RETI to Thread Mode, use PSP */
+
+ /*------------------- User SVC ------------------------------*/
+
+SVC_User:
+ PUSH {R4,LR} /* Save Registers */
+ LDR R2,=SVC_Count
+ LDR R2,[R2]
+ CMP R1,R2
+ BHI SVC_Done /* Overflow */
+
+ LDR R4,=SVC_Table-4
+ LSLS R1,R1,#2
+ LDR R4,[R4,R1] /* Load SVC Function Address */
+ MOV LR,R4
+
+ LDMIA R0,{R0-R3,R4} /* Read R0-R3,R12 from stack */
+ MOV R12,R4
+ BLX LR /* Call SVC Function */
+
+ MRS R4,PSP /* Read PSP */
+ STMIA R4!,{R0-R3} /* Function return values */
+SVC_Done:
+ POP {R4,PC} /* RETI */
+
+ .fnend
+ .size SVC_Handler, .-SVC_Handler
+
+
+/*-------------------------- PendSV_Handler ---------------------------------*/
+
+# void PendSV_Handler (void);
+
+ .thumb_func
+ .type PendSV_Handler, %function
+ .global PendSV_Handler
+ .global Sys_Switch
+PendSV_Handler:
+ .fnstart
+ .cantunwind
+
+ BL rt_pop_req
+
+Sys_Switch:
+ LDR R3,=os_tsk
+ LDMIA R3!,{R1,R2} /* os_tsk.run, os_tsk.new */
+ CMP R1,R2
+ BEQ Sys_Exit /* no task switch */
+
+ SUBS R3,#8
+
+ MRS R0,PSP /* Read PSP */
+ SUBS R0,R0,#32 /* Adjust Start Address */
+ STR R0,[R1,#TCB_TSTACK] /* Update os_tsk.run->tsk_stack */
+ STMIA R0!,{R4-R7} /* Save old context (R4-R7) */
+ MOV R4,R8
+ MOV R5,R9
+ MOV R6,R10
+ MOV R7,R11
+ STMIA R0!,{R4-R7} /* Save old context (R8-R11) */
+
+ PUSH {R2,R3}
+ BL rt_stk_check /* Check for Stack overflow */
+ POP {R2,R3}
+
+ STR R2,[R3] /* os_tsk.run = os_tsk.new */
+
+ LDR R0,[R2,#TCB_TSTACK] /* os_tsk.new->tsk_stack */
+ ADDS R0,R0,#16 /* Adjust Start Address */
+ LDMIA R0!,{R4-R7} /* Restore new Context (R8-R11) */
+ MOV R8,R4
+ MOV R9,R5
+ MOV R10,R6
+ MOV R11,R7
+ MSR PSP,R0 /* Write PSP */
+ SUBS R0,R0,#32 /* Adjust Start Address */
+ LDMIA R0!,{R4-R7} /* Restore new Context (R4-R7) */
+
+Sys_Exit:
+ MOVS R0,#~0xFFFFFFFD /* Set EXC_RETURN value */
+ MVNS R0,R0
+ BX R0 /* RETI to Thread Mode, use PSP */
+
+ .fnend
+ .size PendSV_Handler, .-PendSV_Handler
+
+
+/*-------------------------- SysTick_Handler --------------------------------*/
+
+# void SysTick_Handler (void);
+
+ .thumb_func
+ .type SysTick_Handler, %function
+ .global SysTick_Handler
+SysTick_Handler:
+ .fnstart
+ .cantunwind
+
+ BL rt_systick
+ B Sys_Switch
+
+ .fnend
+ .size SysTick_Handler, .-SysTick_Handler
+
+
+/*-------------------------- OS_Tick_Handler --------------------------------*/
+
+# void OS_Tick_Handler (void);
+
+ .thumb_func
+ .type OS_Tick_Handler, %function
+ .global OS_Tick_Handler
+OS_Tick_Handler:
+ .fnstart
+ .cantunwind
+
+ BL os_tick_irqack
+ BL rt_systick
+ B Sys_Switch
+
+ .fnend
+ .size OS_Tick_Handler, .-OS_Tick_Handler
+
+
+ .end
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/LPC11U24/GCC_ARM/SVC_Table.s Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,56 @@ +;/*---------------------------------------------------------------------------- +; * RL-ARM - RTX +; *---------------------------------------------------------------------------- +; * Name: SVC_TABLE.S +; * Purpose: Pre-defined SVC Table for Cortex-M +; * Rev.: V4.50 +; *---------------------------------------------------------------------------- +; * +; * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH +; * All rights reserved. +; * Redistribution and use in source and binary forms, with or without +; * modification, are permitted provided that the following conditions are met: +; * - Redistributions of source code must retain the above copyright +; * notice, this list of conditions and the following disclaimer. +; * - Redistributions in binary form must reproduce the above copyright +; * notice, this list of conditions and the following disclaimer in the +; * documentation and/or other materials provided with the distribution. +; * - Neither the name of ARM nor the names of its contributors may be used +; * to endorse or promote products derived from this software without +; * specific prior written permission. +; * +; * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +; * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +; * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +; * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE +; * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +; * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +; * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +; * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +; * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +; * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +; * POSSIBILITY OF SUCH DAMAGE. +; *---------------------------------------------------------------------------*/ + + + .file "SVC_Table.S" + + + .section ".svc_table" + + .global SVC_Table +SVC_Table: +/* Insert user SVC functions here. SVC 0 used by RTL Kernel. */ +# .long __SVC_1 /* user SVC function */ +SVC_End: + + .global SVC_Count +SVC_Count: + .long (SVC_End-SVC_Table)/4 + + + .end + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/LPC11U24/uARM/HAL_CM0.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,301 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: HAL_CM0.C
+ * Purpose: Hardware Abstraction Layer for Cortex-M0
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_HAL_CM.h"
+#include "rt_Task.h"
+#include "rt_MemBox.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_set_PSP ------------------------------------*/
+
+__asm void rt_set_PSP (U32 stack) {
+ MSR PSP,R0
+ BX LR
+}
+
+
+/*--------------------------- rt_get_PSP ------------------------------------*/
+
+__asm U32 rt_get_PSP (void) {
+ MRS R0,PSP
+ BX LR
+}
+
+
+/*--------------------------- os_set_env ------------------------------------*/
+
+__asm void os_set_env (void) {
+ /* Switch to Unprivileged/Privileged Thread mode, use PSP. */
+ MOV R0,SP ; PSP = MSP
+ MSR PSP,R0
+ LDR R0,=__cpp(&os_flags)
+ LDRB R0,[R0]
+ LSLS R0,#31
+ BNE PrivilegedE
+ MOVS R0,#0x03 ; Unprivileged Thread mode, use PSP
+ MSR CONTROL,R0
+ BX LR
+PrivilegedE
+ MOVS R0,#0x02 ; Privileged Thread mode, use PSP
+ MSR CONTROL,R0
+ BX LR
+
+ ALIGN
+}
+
+
+/*--------------------------- _alloc_box ------------------------------------*/
+
+__asm void *_alloc_box (void *box_mem) {
+ /* Function wrapper for Unprivileged/Privileged mode. */
+ LDR R3,=__cpp(rt_alloc_box)
+ MOV R12,R3
+ MRS R3,IPSR
+ LSLS R3,#24
+ BNE PrivilegedA
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BEQ PrivilegedA
+ SVC 0
+ BX LR
+PrivilegedA
+ BX R12
+
+ ALIGN
+}
+
+
+/*--------------------------- _free_box -------------------------------------*/
+
+__asm int _free_box (void *box_mem, void *box) {
+ /* Function wrapper for Unprivileged/Privileged mode. */
+ LDR R3,=__cpp(rt_free_box)
+ MOV R12,R3
+ MRS R3,IPSR
+ LSLS R3,#24
+ BNE PrivilegedF
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BEQ PrivilegedF
+ SVC 0
+ BX LR
+PrivilegedF
+ BX R12
+
+ ALIGN
+}
+
+
+/*-------------------------- SVC_Handler ------------------------------------*/
+
+__asm void SVC_Handler (void) {
+ PRESERVE8
+
+ IMPORT SVC_Count
+ IMPORT SVC_Table
+ IMPORT rt_stk_check
+
+ MRS R0,PSP ; Read PSP
+ LDR R1,[R0,#24] ; Read Saved PC from Stack
+ SUBS R1,R1,#2 ; Point to SVC Instruction
+ LDRB R1,[R1] ; Load SVC Number
+ CMP R1,#0
+ BNE SVC_User ; User SVC Number > 0
+
+ MOV LR,R4
+ LDMIA R0,{R0-R3,R4} ; Read R0-R3,R12 from stack
+ MOV R12,R4
+ MOV R4,LR
+ BLX R12 ; Call SVC Function
+
+ MRS R3,PSP ; Read PSP
+ STMIA R3!,{R0-R2} ; Store return values
+
+ LDR R3,=__cpp(&os_tsk)
+ LDMIA R3!,{R1,R2} ; os_tsk.run, os_tsk.new
+ CMP R1,R2
+ BEQ SVC_Exit ; no task switch
+
+ SUBS R3,#8
+ CMP R1,#0 ; Runtask deleted?
+ BEQ SVC_Next
+
+ MRS R0,PSP ; Read PSP
+ SUBS R0,R0,#32 ; Adjust Start Address
+ STR R0,[R1,#TCB_TSTACK] ; Update os_tsk.run->tsk_stack
+ STMIA R0!,{R4-R7} ; Save old context (R4-R7)
+ MOV R4,R8
+ MOV R5,R9
+ MOV R6,R10
+ MOV R7,R11
+ STMIA R0!,{R4-R7} ; Save old context (R8-R11)
+
+ PUSH {R2,R3}
+ BL rt_stk_check ; Check for Stack overflow
+ POP {R2,R3}
+
+SVC_Next
+ STR R2,[R3] ; os_tsk.run = os_tsk.new
+
+ LDR R0,[R2,#TCB_TSTACK] ; os_tsk.new->tsk_stack
+ ADDS R0,R0,#16 ; Adjust Start Address
+ LDMIA R0!,{R4-R7} ; Restore new Context (R8-R11)
+ MOV R8,R4
+ MOV R9,R5
+ MOV R10,R6
+ MOV R11,R7
+ MSR PSP,R0 ; Write PSP
+ SUBS R0,R0,#32 ; Adjust Start Address
+ LDMIA R0!,{R4-R7} ; Restore new Context (R4-R7)
+
+SVC_Exit
+ MOVS R0,#:NOT:0xFFFFFFFD ; Set EXC_RETURN value
+ MVNS R0,R0
+ BX R0 ; RETI to Thread Mode, use PSP
+
+ /*------------------- User SVC ------------------------------*/
+
+SVC_User
+ PUSH {R4,LR} ; Save Registers
+ LDR R2,=SVC_Count
+ LDR R2,[R2]
+ CMP R1,R2
+ BHI SVC_Done ; Overflow
+
+ LDR R4,=SVC_Table-4
+ LSLS R1,R1,#2
+ LDR R4,[R4,R1] ; Load SVC Function Address
+ MOV LR,R4
+
+ LDMIA R0,{R0-R3,R4} ; Read R0-R3,R12 from stack
+ MOV R12,R4
+ BLX LR ; Call SVC Function
+
+ MRS R4,PSP ; Read PSP
+ STMIA R4!,{R0-R3} ; Function return values
+SVC_Done
+ POP {R4,PC} ; RETI
+
+ ALIGN
+}
+
+
+/*-------------------------- PendSV_Handler ---------------------------------*/
+
+__asm void PendSV_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(rt_pop_req)
+
+Sys_Switch
+ LDR R3,=__cpp(&os_tsk)
+ LDMIA R3!,{R1,R2} ; os_tsk.run, os_tsk.new
+ CMP R1,R2
+ BEQ Sys_Exit ; no task switch
+
+ SUBS R3,#8
+
+ MRS R0,PSP ; Read PSP
+ SUBS R0,R0,#32 ; Adjust Start Address
+ STR R0,[R1,#TCB_TSTACK] ; Update os_tsk.run->tsk_stack
+ STMIA R0!,{R4-R7} ; Save old context (R4-R7)
+ MOV R4,R8
+ MOV R5,R9
+ MOV R6,R10
+ MOV R7,R11
+ STMIA R0!,{R4-R7} ; Save old context (R8-R11)
+
+ PUSH {R2,R3}
+ BL rt_stk_check ; Check for Stack overflow
+ POP {R2,R3}
+
+ STR R2,[R3] ; os_tsk.run = os_tsk.new
+
+ LDR R0,[R2,#TCB_TSTACK] ; os_tsk.new->tsk_stack
+ ADDS R0,R0,#16 ; Adjust Start Address
+ LDMIA R0!,{R4-R7} ; Restore new Context (R8-R11)
+ MOV R8,R4
+ MOV R9,R5
+ MOV R10,R6
+ MOV R11,R7
+ MSR PSP,R0 ; Write PSP
+ SUBS R0,R0,#32 ; Adjust Start Address
+ LDMIA R0!,{R4-R7} ; Restore new Context (R4-R7)
+
+Sys_Exit
+ MOVS R0,#:NOT:0xFFFFFFFD ; Set EXC_RETURN value
+ MVNS R0,R0
+ BX R0 ; RETI to Thread Mode, use PSP
+
+ ALIGN
+}
+
+
+/*-------------------------- SysTick_Handler --------------------------------*/
+
+__asm void SysTick_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(rt_systick)
+ B Sys_Switch
+
+ ALIGN
+}
+
+
+/*-------------------------- OS_Tick_Handler --------------------------------*/
+
+__asm void OS_Tick_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(os_tick_irqack)
+ BL __cpp(rt_systick)
+ B Sys_Switch
+
+ ALIGN
+}
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/LPC11U24/uARM/SVC_Table.s Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,57 @@ +;/*---------------------------------------------------------------------------- +; * RL-ARM - RTX +; *---------------------------------------------------------------------------- +; * Name: SVC_TABLE.S +; * Purpose: Pre-defined SVC Table for Cortex-M +; * Rev.: V4.50 +; *---------------------------------------------------------------------------- +; * +; * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH +; * All rights reserved. +; * Redistribution and use in source and binary forms, with or without +; * modification, are permitted provided that the following conditions are met: +; * - Redistributions of source code must retain the above copyright +; * notice, this list of conditions and the following disclaimer. +; * - Redistributions in binary form must reproduce the above copyright +; * notice, this list of conditions and the following disclaimer in the +; * documentation and/or other materials provided with the distribution. +; * - Neither the name of ARM nor the names of its contributors may be used +; * to endorse or promote products derived from this software without +; * specific prior written permission. +; * +; * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +; * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +; * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +; * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE +; * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +; * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +; * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +; * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +; * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +; * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +; * POSSIBILITY OF SUCH DAMAGE. +; *---------------------------------------------------------------------------*/ + + + AREA SVC_TABLE, CODE, READONLY + + EXPORT SVC_Count + +SVC_Cnt EQU (SVC_End-SVC_Table)/4 +SVC_Count DCD SVC_Cnt + +; Import user SVC functions here. +; IMPORT __SVC_1 + + EXPORT SVC_Table +SVC_Table +; Insert user SVC functions here. SVC 0 used by RTL Kernel. +; DCD __SVC_1 ; user SVC function + +SVC_End + + END + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/LPC1768/ARM/HAL_CM3.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,249 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: HAL_CM3.C
+ * Purpose: Hardware Abstraction Layer for Cortex-M3
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_HAL_CM.h"
+#include "rt_Task.h"
+#include "rt_MemBox.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_set_PSP ------------------------------------*/
+
+__asm void rt_set_PSP (U32 stack) {
+ MSR PSP,R0
+ BX LR
+}
+
+
+/*--------------------------- rt_get_PSP ------------------------------------*/
+
+__asm U32 rt_get_PSP (void) {
+ MRS R0,PSP
+ BX LR
+}
+
+
+/*--------------------------- os_set_env ------------------------------------*/
+
+__asm void os_set_env (void) {
+ /* Switch to Unprivileged/Privileged Thread mode, use PSP. */
+ MOV R0,SP ; PSP = MSP
+ MSR PSP,R0
+ LDR R0,=__cpp(&os_flags)
+ LDRB R0,[R0]
+ LSLS R0,#31
+ MOVNE R0,#0x02 ; Privileged Thread mode, use PSP
+ MOVEQ R0,#0x03 ; Unprivileged Thread mode, use PSP
+ MSR CONTROL,R0
+ BX LR
+
+ ALIGN
+}
+
+
+/*--------------------------- _alloc_box ------------------------------------*/
+
+__asm void *_alloc_box (void *box_mem) {
+ /* Function wrapper for Unprivileged/Privileged mode. */
+ LDR R12,=__cpp(rt_alloc_box)
+ MRS R3,IPSR
+ LSLS R3,#24
+ BXNE R12
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BXEQ R12
+ SVC 0
+ BX LR
+
+ ALIGN
+}
+
+
+/*--------------------------- _free_box -------------------------------------*/
+
+__asm int _free_box (void *box_mem, void *box) {
+ /* Function wrapper for Unprivileged/Privileged mode. */
+ LDR R12,=__cpp(rt_free_box)
+ MRS R3,IPSR
+ LSLS R3,#24
+ BXNE R12
+ MRS R3,CONTROL
+ LSLS R3,#31
+ BXEQ R12
+ SVC 0
+ BX LR
+
+ ALIGN
+}
+
+
+/*-------------------------- SVC_Handler ------------------------------------*/
+
+__asm void SVC_Handler (void) {
+ PRESERVE8
+
+ IMPORT SVC_Count
+ IMPORT SVC_Table
+ IMPORT rt_stk_check
+
+ MRS R0,PSP ; Read PSP
+ LDR R1,[R0,#24] ; Read Saved PC from Stack
+ LDRB R1,[R1,#-2] ; Load SVC Number
+ CBNZ R1,SVC_User
+
+ LDM R0,{R0-R3,R12} ; Read R0-R3,R12 from stack
+ BLX R12 ; Call SVC Function
+
+ MRS R12,PSP ; Read PSP
+ STM R12,{R0-R2} ; Store return values
+
+ LDR R3,=__cpp(&os_tsk)
+ LDM R3,{R1,R2} ; os_tsk.run, os_tsk.new
+ CMP R1,R2
+ BEQ SVC_Exit ; no task switch
+
+ CBZ R1,SVC_Next ; Runtask deleted?
+ STMDB R12!,{R4-R11} ; Save Old context
+ STR R12,[R1,#TCB_TSTACK] ; Update os_tsk.run->tsk_stack
+
+ PUSH {R2,R3}
+ BL rt_stk_check ; Check for Stack overflow
+ POP {R2,R3}
+
+SVC_Next
+ STR R2,[R3] ; os_tsk.run = os_tsk.new
+
+ LDR R12,[R2,#TCB_TSTACK] ; os_tsk.new->tsk_stack
+ LDMIA R12!,{R4-R11} ; Restore New Context
+ MSR PSP,R12 ; Write PSP
+
+SVC_Exit
+ MVN LR,#:NOT:0xFFFFFFFD ; set EXC_RETURN value
+ BX LR
+
+ /*------------------- User SVC ------------------------------*/
+
+SVC_User
+ PUSH {R4,LR} ; Save Registers
+ LDR R2,=SVC_Count
+ LDR R2,[R2]
+ CMP R1,R2
+ BHI SVC_Done ; Overflow
+
+ LDR R4,=SVC_Table-4
+ LDR R4,[R4,R1,LSL #2] ; Load SVC Function Address
+
+ LDM R0,{R0-R3,R12} ; Read R0-R3,R12 from stack
+ BLX R4 ; Call SVC Function
+
+ MRS R12,PSP
+ STM R12,{R0-R3} ; Function return values
+SVC_Done
+ POP {R4,PC} ; RETI
+
+ ALIGN
+}
+
+
+/*-------------------------- PendSV_Handler ---------------------------------*/
+
+__asm void PendSV_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(rt_pop_req)
+
+Sys_Switch
+ LDR R3,=__cpp(&os_tsk)
+ LDM R3,{R1,R2} ; os_tsk.run, os_tsk.new
+ CMP R1,R2
+ BEQ Sys_Exit
+
+ MRS R12,PSP ; Read PSP
+ STMDB R12!,{R4-R11} ; Save Old context
+ STR R12,[R1,#TCB_TSTACK] ; Update os_tsk.run->tsk_stack
+
+ PUSH {R2,R3}
+ BL rt_stk_check ; Check for Stack overflow
+ POP {R2,R3}
+
+ STR R2,[R3] ; os_tsk.run = os_tsk.new
+
+ LDR R12,[R2,#TCB_TSTACK] ; os_tsk.new->tsk_stack
+ LDMIA R12!,{R4-R11} ; Restore New Context
+ MSR PSP,R12 ; Write PSP
+
+Sys_Exit
+ MVN LR,#:NOT:0xFFFFFFFD ; set EXC_RETURN value
+ BX LR ; Return to Thread Mode
+
+ ALIGN
+}
+
+
+/*-------------------------- SysTick_Handler --------------------------------*/
+
+__asm void SysTick_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(rt_systick)
+ B Sys_Switch
+
+ ALIGN
+}
+
+
+/*-------------------------- OS_Tick_Handler --------------------------------*/
+
+__asm void OS_Tick_Handler (void) {
+ PRESERVE8
+
+ BL __cpp(os_tick_irqack)
+ BL __cpp(rt_systick)
+ B Sys_Switch
+
+ ALIGN
+}
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/LPC1768/ARM/SVC_Table.s Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,57 @@ +;/*---------------------------------------------------------------------------- +; * RL-ARM - RTX +; *---------------------------------------------------------------------------- +; * Name: SVC_TABLE.S +; * Purpose: Pre-defined SVC Table for Cortex-M +; * Rev.: V4.50 +; *---------------------------------------------------------------------------- +; * +; * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH +; * All rights reserved. +; * Redistribution and use in source and binary forms, with or without +; * modification, are permitted provided that the following conditions are met: +; * - Redistributions of source code must retain the above copyright +; * notice, this list of conditions and the following disclaimer. +; * - Redistributions in binary form must reproduce the above copyright +; * notice, this list of conditions and the following disclaimer in the +; * documentation and/or other materials provided with the distribution. +; * - Neither the name of ARM nor the names of its contributors may be used +; * to endorse or promote products derived from this software without +; * specific prior written permission. +; * +; * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +; * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +; * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +; * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE +; * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +; * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +; * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +; * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +; * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +; * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +; * POSSIBILITY OF SUCH DAMAGE. +; *---------------------------------------------------------------------------*/ + + + AREA SVC_TABLE, CODE, READONLY + + EXPORT SVC_Count + +SVC_Cnt EQU (SVC_End-SVC_Table)/4 +SVC_Count DCD SVC_Cnt + +; Import user SVC functions here. +; IMPORT __SVC_1 + + EXPORT SVC_Table +SVC_Table +; Insert user SVC functions here. SVC 0 used by RTL Kernel. +; DCD __SVC_1 ; user SVC function + +SVC_End + + END + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/LPC1768/GCC_ARM/HAL_CM3.s Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,323 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: HAL_CM3.S
+ * Purpose: Hardware Abstraction Layer for Cortex-M3
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+ .file "HAL_CM3.S"
+ .syntax unified
+
+ .equ TCB_TSTACK, 36
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+ .thumb
+
+ .section ".text"
+ .align 2
+
+
+/*--------------------------- rt_set_PSP ------------------------------------*/
+
+# void rt_set_PSP (U32 stack);
+
+ .thumb_func
+ .type rt_set_PSP, %function
+ .global rt_set_PSP
+rt_set_PSP:
+ .fnstart
+ .cantunwind
+
+ MSR PSP,R0
+ BX LR
+
+ .fnend
+ .size rt_set_PSP, .-rt_set_PSP
+
+
+/*--------------------------- rt_get_PSP ------------------------------------*/
+
+# U32 rt_get_PSP (void);
+
+ .thumb_func
+ .type rt_get_PSP, %function
+ .global rt_get_PSP
+rt_get_PSP:
+ .fnstart
+ .cantunwind
+
+ MRS R0,PSP
+ BX LR
+
+ .fnend
+ .size rt_get_PSP, .-rt_get_PSP
+
+
+/*--------------------------- os_set_env ------------------------------------*/
+
+# void os_set_env (void);
+ /* Switch to Unprivileged/Privileged Thread mode, use PSP. */
+
+ .thumb_func
+ .type os_set_env, %function
+ .global os_set_env
+os_set_env:
+ .fnstart
+ .cantunwind
+
+ MOV R0,SP /* PSP = MSP */
+ MSR PSP,R0
+ LDR R0,=os_flags
+ LDRB R0,[R0]
+ LSLS R0,#31
+ ITE NE
+ MOVNE R0,#0x02 /* Privileged Thread mode, use PSP */
+ MOVEQ R0,#0x03 /* Unprivileged Thread mode, use PSP */
+ MSR CONTROL,R0
+ BX LR
+
+ .fnend
+ .size os_set_env, .-os_set_env
+
+
+/*--------------------------- _alloc_box ------------------------------------*/
+
+# void *_alloc_box (void *box_mem);
+ /* Function wrapper for Unprivileged/Privileged mode. */
+
+ .thumb_func
+ .type _alloc_box, %function
+ .global _alloc_box
+_alloc_box:
+ .fnstart
+ .cantunwind
+
+ LDR R12,=rt_alloc_box
+ MRS R3,IPSR
+ LSLS R3,#24
+ IT NE
+ BXNE R12
+ MRS R3,CONTROL
+ LSLS R3,#31
+ IT EQ
+ BXEQ R12
+ SVC 0
+ BX LR
+
+ .fnend
+ .size _alloc_box, .-_alloc_box
+
+
+/*--------------------------- _free_box -------------------------------------*/
+
+# int _free_box (void *box_mem, void *box);
+ /* Function wrapper for Unprivileged/Privileged mode. */
+
+ .thumb_func
+ .type _free_box, %function
+ .global _free_box
+_free_box:
+ .fnstart
+ .cantunwind
+
+ LDR R12,=rt_free_box
+ MRS R3,IPSR
+ LSLS R3,#24
+ IT NE
+ BXNE R12
+ MRS R3,CONTROL
+ LSLS R3,#31
+ IT EQ
+ BXEQ R12
+ SVC 0
+ BX LR
+
+ .fnend
+ .size _free_box, .-_free_box
+
+
+/*-------------------------- SVC_Handler ------------------------------------*/
+
+# void SVC_Handler (void);
+
+ .thumb_func
+ .type SVC_Handler, %function
+ .global SVC_Handler
+SVC_Handler:
+ .fnstart
+ .cantunwind
+
+ MRS R0,PSP /* Read PSP */
+ LDR R1,[R0,#24] /* Read Saved PC from Stack */
+ LDRB R1,[R1,#-2] /* Load SVC Number */
+ CBNZ R1,SVC_User
+
+ LDM R0,{R0-R3,R12} /* Read R0-R3,R12 from stack */
+ BLX R12 /* Call SVC Function */
+
+ MRS R12,PSP /* Read PSP */
+ STM R12,{R0-R2} /* Store return values */
+
+ LDR R3,=os_tsk
+ LDM R3,{R1,R2} /* os_tsk.run, os_tsk.new */
+ CMP R1,R2
+ BEQ SVC_Exit /* no task switch */
+
+ CBZ R1,SVC_Next /* Runtask deleted? */
+ STMDB R12!,{R4-R11} /* Save Old context */
+ STR R12,[R1,#TCB_TSTACK] /* Update os_tsk.run->tsk_stack */
+
+ PUSH {R2,R3}
+ BL rt_stk_check /* Check for Stack overflow */
+ POP {R2,R3}
+
+SVC_Next:
+ STR R2,[R3] /* os_tsk.run = os_tsk.new */
+
+ LDR R12,[R2,#TCB_TSTACK] /* os_tsk.new->tsk_stack */
+ LDMIA R12!,{R4-R11} /* Restore New Context */
+ MSR PSP,R12 /* Write PSP */
+
+SVC_Exit:
+ MVN LR,#~0xFFFFFFFD /* set EXC_RETURN value */
+ BX LR
+
+ /*------------------- User SVC ------------------------------*/
+
+SVC_User:
+ PUSH {R4,LR} /* Save Registers */
+ LDR R2,=SVC_Count
+ LDR R2,[R2]
+ CMP R1,R2
+ BHI SVC_Done /* Overflow */
+
+ LDR R4,=SVC_Table-4
+ LDR R4,[R4,R1,LSL #2] /* Load SVC Function Address */
+
+ LDM R0,{R0-R3,R12} /* Read R0-R3,R12 from stack */
+ BLX R4 /* Call SVC Function */
+
+ MRS R12,PSP
+ STM R12,{R0-R3} /* Function return values */
+SVC_Done:
+ POP {R4,PC} /* RETI */
+
+ .fnend
+ .size SVC_Handler, .-SVC_Handler
+
+
+/*-------------------------- PendSV_Handler ---------------------------------*/
+
+# void PendSV_Handler (void);
+
+ .thumb_func
+ .type PendSV_Handler, %function
+ .global PendSV_Handler
+ .global Sys_Switch
+PendSV_Handler:
+ .fnstart
+ .cantunwind
+
+ BL rt_pop_req
+
+Sys_Switch:
+ LDR R3,=os_tsk
+ LDM R3,{R1,R2} /* os_tsk.run, os_tsk.new */
+ CMP R1,R2
+ BEQ Sys_Exit
+
+ MRS R12,PSP /* Read PSP */
+ STMDB R12!,{R4-R11} /* Save Old context */
+ STR R12,[R1,#TCB_TSTACK] /* Update os_tsk.run->tsk_stack */
+
+ PUSH {R2,R3}
+ BL rt_stk_check /* Check for Stack overflow */
+ POP {R2,R3}
+
+ STR R2,[R3] /* os_tsk.run = os_tsk.new */
+
+ LDR R12,[R2,#TCB_TSTACK] /* os_tsk.new->tsk_stack */
+ LDMIA R12!,{R4-R11} /* Restore New Context */
+ MSR PSP,R12 /* Write PSP */
+
+Sys_Exit:
+ MVN LR,#~0xFFFFFFFD /* set EXC_RETURN value */
+ BX LR /* Return to Thread Mode */
+
+ .fnend
+ .size PendSV_Handler, .-PendSV_Handler
+
+
+/*-------------------------- SysTick_Handler --------------------------------*/
+
+# void SysTick_Handler (void);
+
+ .thumb_func
+ .type SysTick_Handler, %function
+ .global SysTick_Handler
+SysTick_Handler:
+ .fnstart
+ .cantunwind
+
+ BL rt_systick
+ B Sys_Switch
+
+ .fnend
+ .size SysTick_Handler, .-SysTick_Handler
+
+
+/*-------------------------- OS_Tick_Handler --------------------------------*/
+
+# void OS_Tick_Handler (void);
+
+ .thumb_func
+ .type OS_Tick_Handler, %function
+ .global OS_Tick_Handler
+OS_Tick_Handler:
+ .fnstart
+ .cantunwind
+
+ BL os_tick_irqack
+ BL rt_systick
+ B Sys_Switch
+
+ .fnend
+ .size OS_Tick_Handler, .-OS_Tick_Handler
+
+
+ .end
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/LPC1768/GCC_ARM/SVC_Table.s Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,56 @@ +;/*---------------------------------------------------------------------------- +; * RL-ARM - RTX +; *---------------------------------------------------------------------------- +; * Name: SVC_TABLE.S +; * Purpose: Pre-defined SVC Table for Cortex-M +; * Rev.: V4.50 +; *---------------------------------------------------------------------------- +; * +; * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH +; * All rights reserved. +; * Redistribution and use in source and binary forms, with or without +; * modification, are permitted provided that the following conditions are met: +; * - Redistributions of source code must retain the above copyright +; * notice, this list of conditions and the following disclaimer. +; * - Redistributions in binary form must reproduce the above copyright +; * notice, this list of conditions and the following disclaimer in the +; * documentation and/or other materials provided with the distribution. +; * - Neither the name of ARM nor the names of its contributors may be used +; * to endorse or promote products derived from this software without +; * specific prior written permission. +; * +; * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +; * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +; * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +; * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE +; * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +; * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +; * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +; * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +; * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +; * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +; * POSSIBILITY OF SUCH DAMAGE. +; *---------------------------------------------------------------------------*/ + + + .file "SVC_Table.S" + + + .section ".svc_table" + + .global SVC_Table +SVC_Table: +/* Insert user SVC functions here. SVC 0 used by RTL Kernel. */ +# .long __SVC_1 /* user SVC function */ +SVC_End: + + .global SVC_Count +SVC_Count: + .long (SVC_End-SVC_Table)/4 + + + .end + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/RTX_CM_lib.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,367 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RTX_CM_LIB.H
+ * Purpose: RTX Kernel System Configuration
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#if defined (__CC_ARM)
+#pragma O3
+#define __USED __attribute__((used))
+#elif defined (__GNUC__)
+#pragma GCC optimize ("O3")
+#define __USED __attribute__((used))
+#elif defined (__ICCARM__)
+#define __USED __root
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * Definitions
+ *---------------------------------------------------------------------------*/
+
+#define _declare_box(pool,size,cnt) uint32_t pool[(((size)+3)/4)*(cnt) + 3]
+#define _declare_box8(pool,size,cnt) uint64_t pool[(((size)+7)/8)*(cnt) + 2]
+
+#define OS_TCB_SIZE 48
+#define OS_TMR_SIZE 8
+
+#if defined (__CC_ARM) && !defined (__MICROLIB)
+
+typedef void *OS_ID;
+typedef uint32_t OS_TID;
+typedef uint32_t OS_MUT[3];
+typedef uint32_t OS_RESULT;
+
+#define runtask_id() rt_tsk_self()
+#define mutex_init(m) rt_mut_init(m)
+#define mutex_wait(m) os_mut_wait(m,0xFFFF)
+#define mutex_rel(m) os_mut_release(m)
+
+extern OS_TID rt_tsk_self (void);
+extern void rt_mut_init (OS_ID mutex);
+extern OS_RESULT rt_mut_release (OS_ID mutex);
+extern OS_RESULT rt_mut_wait (OS_ID mutex, uint16_t timeout);
+
+#define os_mut_wait(mutex,timeout) _os_mut_wait((uint32_t)rt_mut_wait,mutex,timeout)
+#define os_mut_release(mutex) _os_mut_release((uint32_t)rt_mut_release,mutex)
+
+OS_RESULT _os_mut_release (uint32_t p, OS_ID mutex) __svc_indirect(0);
+OS_RESULT _os_mut_wait (uint32_t p, OS_ID mutex, uint16_t timeout) __svc_indirect(0);
+
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+#if (OS_TIMERS != 0)
+#define OS_TASK_CNT (OS_TASKCNT + 1)
+#else
+#define OS_TASK_CNT OS_TASKCNT
+#endif
+
+uint16_t const os_maxtaskrun = OS_TASK_CNT;
+uint32_t const os_rrobin = (OS_ROBIN << 16) | OS_ROBINTOUT;
+uint32_t const os_trv = OS_TRV;
+uint8_t const os_flags = OS_RUNPRIV;
+
+/* Export following defines to uVision debugger. */
+__USED uint32_t const os_clockrate = OS_TICK;
+__USED uint32_t const os_timernum = 0;
+
+/* Stack for the os_idle_demon */
+unsigned int idle_task_stack[OS_IDLESTKSIZE];
+unsigned short const idle_task_stack_size = OS_IDLESTKSIZE;
+
+#ifndef OS_FIFOSZ
+ #define OS_FIFOSZ 16
+#endif
+
+/* Fifo Queue buffer for ISR requests.*/
+uint32_t os_fifo[OS_FIFOSZ*2+1];
+uint8_t const os_fifo_size = OS_FIFOSZ;
+
+/* An array of Active task pointers. */
+void *os_active_TCB[OS_TASK_CNT];
+
+/* User Timers Resources */
+#if (OS_TIMERS != 0)
+extern void osTimerThread (void const *argument);
+osThreadDef(osTimerThread, (osPriority)(OS_TIMERPRIO-3), 4*OS_TIMERSTKSZ);
+osThreadId osThreadId_osTimerThread;
+osMessageQDef(osTimerMessageQ, OS_TIMERCBQS, void *);
+osMessageQId osMessageQId_osTimerMessageQ;
+#else
+osThreadDef_t os_thread_def_osTimerThread = { NULL };
+osThreadId osThreadId_osTimerThread;
+osMessageQDef(osTimerMessageQ, 0, void *);
+osMessageQId osMessageQId_osTimerMessageQ;
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * RTX Optimizations (empty functions)
+ *---------------------------------------------------------------------------*/
+
+#if OS_ROBIN == 0
+ void rt_init_robin (void) {;}
+ void rt_chk_robin (void) {;}
+#endif
+
+#if OS_STKCHECK == 0
+ void rt_stk_check (void) {;}
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * Standard Library multithreading interface
+ *---------------------------------------------------------------------------*/
+
+#if defined (__CC_ARM) && !defined (__MICROLIB)
+ static OS_MUT std_libmutex[OS_MUTEXCNT];
+ static uint32_t nr_mutex;
+
+ /*--------------------------- _mutex_initialize -----------------------------*/
+
+int _mutex_initialize (OS_ID *mutex) {
+ /* Allocate and initialize a system mutex. */
+
+ if (nr_mutex >= OS_MUTEXCNT) {
+ /* If you are here, you need to increase the number OS_MUTEXCNT. */
+ for (;;);
+ }
+ *mutex = &std_libmutex[nr_mutex++];
+ mutex_init (*mutex);
+ return (1);
+}
+
+
+/*--------------------------- _mutex_acquire --------------------------------*/
+
+__attribute__((used)) void _mutex_acquire (OS_ID *mutex) {
+ /* Acquire a system mutex, lock stdlib resources. */
+ if (runtask_id ()) {
+ /* RTX running, acquire a mutex. */
+ mutex_wait (*mutex);
+ }
+}
+
+
+/*--------------------------- _mutex_release --------------------------------*/
+
+__attribute__((used)) void _mutex_release (OS_ID *mutex) {
+ /* Release a system mutex, unlock stdlib resources. */
+ if (runtask_id ()) {
+ /* RTX runnning, release a mutex. */
+ mutex_rel (*mutex);
+ }
+}
+
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * RTX Startup
+ *---------------------------------------------------------------------------*/
+
+/* Main Thread definition */
+extern int main (void);
+osThreadDef_t os_thread_def_main = {(os_pthread)main, osPriorityNormal, 0, NULL};
+
+#if defined (__CC_ARM)
+
+// This define should be probably moved to the CMSIS layer
+#ifdef TARGET_LPC1768
+#define INITIAL_SP (0x10008000UL)
+
+#elif TARGET_LPC11U24
+#define INITIAL_SP (0x10001000UL)
+
+#endif
+
+extern unsigned char Image$$RW_IRAM1$$ZI$$Limit[];
+
+void set_main_stack(void) {
+ // Leave OS_SCHEDULERSTKSIZE words for the scheduler and interrupts
+ os_thread_def_main.stack_pointer = Image$$RW_IRAM1$$ZI$$Limit;
+ os_thread_def_main.stacksize = (INITIAL_SP - (unsigned int)Image$$RW_IRAM1$$ZI$$Limit) - (OS_SCHEDULERSTKSIZE * 4);
+}
+
+#ifdef __MICROLIB
+void _main_init (void) __attribute__((section(".ARM.Collect$$$$000000FF")));
+void _main_init (void) {
+ osKernelInitialize();
+ set_main_stack();
+ osThreadCreate(&os_thread_def_main, NULL);
+ osKernelStart();
+ for (;;);
+}
+#else
+
+/* The single memory model is checking for stack collision at run time, verifing
+ that the heap pointer is underneath the stack pointer.
+
+ With the RTOS there is not only one stack above the heap, there are multiple
+ stacks and some of them are underneath the heap pointer.
+*/
+#pragma import(__use_two_region_memory)
+
+__asm void __rt_entry (void) {
+
+ IMPORT __user_setup_stackheap
+ IMPORT __rt_lib_init
+ IMPORT os_thread_def_main
+ IMPORT osKernelInitialize
+ IMPORT set_main_stack
+ IMPORT osKernelStart
+ IMPORT osThreadCreate
+ IMPORT exit
+
+ BL __user_setup_stackheap
+ MOV R1,R2
+ BL __rt_lib_init
+ BL osKernelInitialize
+ BL set_main_stack
+ LDR R0,=os_thread_def_main
+ MOVS R1,#0
+ BL osThreadCreate
+ BL osKernelStart
+ BL exit
+
+ ALIGN
+}
+#endif
+
+#elif defined (__GNUC__)
+
+#ifdef __CS3__
+
+/* CS3 start_c routine.
+ *
+ * Copyright (c) 2006, 2007 CodeSourcery Inc
+ *
+ * The authors hereby grant permission to use, copy, modify, distribute,
+ * and license this software and its documentation for any purpose, provided
+ * that existing copyright notices are retained in all copies and that this
+ * notice is included verbatim in any distributions. No written agreement,
+ * license, or royalty fee is required for any of the authorized uses.
+ * Modifications to this software may be copyrighted by their authors
+ * and need not follow the licensing terms described here, provided that
+ * the new terms are clearly indicated on the first page of each file where
+ * they apply.
+ */
+
+#include "cs3.h"
+
+extern void __libc_init_array (void);
+
+__attribute ((noreturn)) void __cs3_start_c (void){
+ unsigned regions = __cs3_region_num;
+ const struct __cs3_region *rptr = __cs3_regions;
+
+ /* Initialize memory */
+ for (regions = __cs3_region_num, rptr = __cs3_regions; regions--; rptr++) {
+ long long *src = (long long *)rptr->init;
+ long long *dst = (long long *)rptr->data;
+ unsigned limit = rptr->init_size;
+ unsigned count;
+
+ if (src != dst)
+ for (count = 0; count != limit; count += sizeof (long long))
+ *dst++ = *src++;
+ else
+ dst = (long long *)((char *)dst + limit);
+ limit = rptr->zero_size;
+ for (count = 0; count != limit; count += sizeof (long long))
+ *dst++ = 0;
+ }
+
+ /* Run initializers. */
+ __libc_init_array ();
+
+ osKernelInitialize();
+ osThreadCreate(&os_thread_def_main, NULL);
+ osKernelStart();
+ for (;;);
+}
+
+#else
+
+__attribute__((naked)) void software_init_hook (void) {
+ __asm (
+ ".syntax unified\n"
+ ".thumb\n"
+ "movs r0,#0\n"
+ "movs r1,#0\n"
+ "mov r4,r0\n"
+ "mov r5,r1\n"
+ "ldr r0,= __libc_fini_array\n"
+ "bl atexit\n"
+ "bl __libc_init_array\n"
+ "mov r0,r4\n"
+ "mov r1,r5\n"
+ "bl osKernelInitialize\n"
+ "ldr r0,=os_thread_def_main\n"
+ "movs r1,#0\n"
+ "bl osThreadCreate\n"
+ "bl osKernelStart\n"
+ "bl exit\n"
+ );
+}
+
+#endif
+
+#elif defined (__ICCARM__)
+
+extern int __low_level_init(void);
+extern void __iar_data_init3(void);
+extern void exit(int arg);
+
+__noreturn __stackless void __cmain(void) {
+ int a;
+
+ if (__low_level_init() != 0) {
+ __iar_data_init3();
+ }
+ osKernelInitialize();
+ osThreadCreate(&os_thread_def_main, NULL);
+ a = osKernelStart();
+ exit(a);
+}
+
+#endif
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/RTX_Conf_CM.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,242 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RTX_Conf_CM.C
+ * Purpose: Configuration of CMSIS RTX Kernel for Cortex-M
+ * Rev.: V4.20
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "cmsis_os.h"
+
+
+/*----------------------------------------------------------------------------
+ * RTX User configuration part BEGIN
+ *---------------------------------------------------------------------------*/
+
+//-------- <<< Use Configuration Wizard in Context Menu >>> -----------------
+//
+// <h>Thread Configuration
+// =======================
+//
+// <o>Number of concurrent running threads <0-250>
+// <i> Defines max. number of threads that will run at the same time.
+// counting "main", but not counting "osTimerThread"
+// <i> Default: 6
+#ifndef OS_TASKCNT
+# if defined(TARGET_LPC1768) || defined(TARGET_LPC2368)
+# define OS_TASKCNT 14
+# elif defined(TARGET_LPC11U24)
+# define OS_TASKCNT 6
+# endif
+#endif
+
+// <o>Scheduler (+ interrupts) stack size [bytes] <64-4096:8><#/4>
+#ifndef OS_SCHEDULERSTKSIZE
+# if defined(TARGET_LPC1768) || defined(TARGET_LPC2368)
+# define OS_SCHEDULERSTKSIZE 256
+# elif defined(TARGET_LPC11U24)
+# define OS_SCHEDULERSTKSIZE 128
+# endif
+#endif
+
+// <o>Idle stack size [bytes] <64-4096:8><#/4>
+// <i> Defines default stack size for the Idle thread.
+#ifndef OS_IDLESTKSIZE
+ #define OS_IDLESTKSIZE 128
+#endif
+
+// <o>Timer Thread stack size [bytes] <64-4096:8><#/4>
+// <i> Defines stack size for Timer thread.
+// <i> Default: 200
+#ifndef OS_TIMERSTKSZ
+ #define OS_TIMERSTKSZ WORDS_STACK_SIZE
+#endif
+
+// <q>Check for stack overflow
+// ===========================
+// <i> Includes the stack checking code for stack overflow.
+// <i> Note that additional code reduces the Kernel performance.
+#ifndef OS_STKCHECK
+ #define OS_STKCHECK 1
+#endif
+
+// <q>Run in privileged mode
+// =========================
+// <i> Runs all Threads in privileged mode.
+// <i> Default: Unprivileged
+#ifndef OS_RUNPRIV
+ #define OS_RUNPRIV 1
+#endif
+
+// </h>
+// <h>SysTick Timer Configuration
+// ==============================
+//
+// <o>Timer clock value [Hz] <1-1000000000>
+// <i> Defines the timer clock value.
+// <i> Default: 6000000 (6MHz)
+#ifndef OS_CLOCK
+# if defined(TARGET_LPC1768) || defined(TARGET_LPC2368)
+# define OS_CLOCK 96000000
+# elif defined(TARGET_LPC11U24)
+# define OS_CLOCK 48000000
+# endif
+#endif
+
+// <o>Timer tick value [us] <1-1000000>
+// <i> Defines the timer tick value.
+// <i> Default: 1000 (1ms)
+#ifndef OS_TICK
+ #define OS_TICK 1000
+#endif
+
+// </h>
+
+// <h>System Configuration
+// =======================
+//
+// <e>Round-Robin Thread switching
+// ===============================
+//
+// <i> Enables Round-Robin Thread switching.
+#ifndef OS_ROBIN
+ #define OS_ROBIN 1
+#endif
+
+// <o>Round-Robin Timeout [ticks] <1-1000>
+// <i> Defines how long a thread will execute before a thread switch.
+// <i> Default: 5
+#ifndef OS_ROBINTOUT
+ #define OS_ROBINTOUT 5
+#endif
+
+// </e>
+
+// <e>User Timers
+// ==============
+// <i> Enables user Timers
+#ifndef OS_TIMERS
+ #define OS_TIMERS 1
+#endif
+
+// <o>Timer Thread Priority
+// <1=> Low
+// <2=> Below Normal
+// <3=> Normal
+// <4=> Above Normal
+// <5=> High
+// <6=> Realtime
+// <i> Defines priority for Timer Thread
+// <i> Default: High
+#ifndef OS_TIMERPRIO
+ #define OS_TIMERPRIO 5
+#endif
+
+// <o>Timer Callback Queue size <1-32>
+// <i> Defines number of concurrent callbacks that will be queued.
+// <i> Default: 4
+#ifndef OS_TIMERCBQSZ
+ #define OS_TIMERCBQS 4
+#endif
+
+// </e>
+
+// <o>ISR FIFO Queue size<4=> 4 entries <8=> 8 entries
+// <12=> 12 entries <16=> 16 entries
+// <24=> 24 entries <32=> 32 entries
+// <48=> 48 entries <64=> 64 entries
+// <96=> 96 entries
+// <i> ISR functions store requests to this buffer,
+// <i> when they are called from the iterrupt handler.
+// <i> Default: 16 entries
+#ifndef OS_FIFOSZ
+ #define OS_FIFOSZ 16
+#endif
+
+// </h>
+
+//------------- <<< end of configuration section >>> -----------------------
+
+// Standard library system mutexes
+// ===============================
+// Define max. number system mutexes that are used to protect
+// the arm standard runtime library. For microlib they are not used.
+#ifndef OS_MUTEXCNT
+ #define OS_MUTEXCNT 8
+#endif
+
+/*----------------------------------------------------------------------------
+ * RTX User configuration part END
+ *---------------------------------------------------------------------------*/
+
+#define OS_TRV ((uint32_t)(((double)OS_CLOCK*(double)OS_TICK)/1E6)-1)
+
+
+/*----------------------------------------------------------------------------
+ * OS Idle daemon
+ *---------------------------------------------------------------------------*/
+void os_idle_demon (void) {
+ /* The idle demon is a system thread, running when no other thread is */
+ /* ready to run. */
+
+ /* Sleep: ideally, we should put the chip to sleep.
+ Unfortunately, this usually requires disconnecting the interface chip (debugger).
+ This can be done, but it would break the local file system.
+ */
+ for (;;) {
+ // sleep();
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * RTX Errors
+ *---------------------------------------------------------------------------*/
+extern void mbed_die(void);
+
+void os_error (uint32_t err_code) {
+ /* This function is called when a runtime error is detected. Parameter */
+ /* 'err_code' holds the runtime error code (defined in RTX_Config.h). */
+ mbed_die();
+}
+
+void sysThreadError(osStatus status) {
+ if (status != osOK) {
+ mbed_die();
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * RTX Configuration Functions
+ *---------------------------------------------------------------------------*/
+
+#include "RTX_CM_lib.h"
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/RTX_Config.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,69 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RTX_CONFIG.H + * Purpose: Exported functions of RTX_Config.c + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +// #define THREAD_STACK_DIAGNOSTIC 1 + +/* Error Codes */ +#define OS_ERR_STK_OVF 1 +#define OS_ERR_FIFO_OVF 2 +#define OS_ERR_MBX_OVF 3 + +/* Definitions */ +#define BOX_ALIGN_8 0x80000000 +#define _declare_box(pool,size,cnt) U32 pool[(((size)+3)/4)*(cnt) + 3] +#define _declare_box8(pool,size,cnt) U64 pool[(((size)+7)/8)*(cnt) + 2] +#define _init_box8(pool,size,bsize) _init_box (pool,size,(bsize) | BOX_ALIGN_8) + +/* Variables */ +extern U32 idle_task_stack[]; +extern U32 os_fifo[]; +extern void *os_active_TCB[]; + +/* Constants */ +extern U16 const os_maxtaskrun; +extern U32 const os_trv; +extern U8 const os_flags; +extern U32 const os_rrobin; +extern U32 const os_clockrate; +extern U32 const os_timernum; +extern U16 const idle_task_stack_size; + +extern U8 const os_fifo_size; + +/* Functions */ +extern void os_idle_demon (void); +extern int os_tick_init (void); +extern void os_tick_irqack (void); +extern void os_tmr_call (U16 info); +extern void os_error (U32 err_code);
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/cmsis_os.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,774 @@
+/* ----------------------------------------------------------------------
+ * Copyright (C) 2012 ARM Limited. All rights reserved.
+ *
+ * $Date: 5. June 2012
+ * $Revision: V1.01
+ *
+ * Project: CMSIS-RTOS API
+ * Title: cmsis_os.h RTX header file
+ *
+ * Version 0.02
+ * Initial Proposal Phase
+ * Version 0.03
+ * osKernelStart added, optional feature: main started as thread
+ * osSemaphores have standard behaviour
+ * osTimerCreate does not start the timer, added osTimerStart
+ * osThreadPass is renamed to osThreadYield
+ * Version 1.01
+ * Support for C++ interface
+ * - const attribute removed from the osXxxxDef_t typedef's
+ * - const attribute added to the osXxxxDef macros
+ * Added: osTimerDelete, osMutexDelete, osSemaphoreDelete
+ * Added: osKernelInitialize
+ * -------------------------------------------------------------------- */
+
+/**
+\page cmsis_os_h Header File Template: cmsis_os.h
+
+The file \b cmsis_os.h is a template header file for a CMSIS-RTOS compliant Real-Time Operating System (RTOS).
+Each RTOS that is compliant with CMSIS-RTOS shall provide a specific \b cmsis_os.h header file that represents
+its implementation.
+
+The file cmsis_os.h contains:
+ - CMSIS-RTOS API function definitions
+ - struct definitions for parameters and return types
+ - status and priority values used by CMSIS-RTOS API functions
+ - macros for defining threads and other kernel objects
+
+
+<b>Name conventions and header file modifications</b>
+
+All definitions are prefixed with \b os to give an unique name space for CMSIS-RTOS functions.
+Definitions that are prefixed \b os_ are not used in the application code but local to this header file.
+All definitions and functions that belong to a module are grouped and have a common prefix, i.e. \b osThread.
+
+Definitions that are marked with <b>CAN BE CHANGED</b> can be adapted towards the needs of the actual CMSIS-RTOS implementation.
+These definitions can be specific to the underlying RTOS kernel.
+
+Definitions that are marked with <b>MUST REMAIN UNCHANGED</b> cannot be altered. Otherwise the CMSIS-RTOS implementation is no longer
+compliant to the standard. Note that some functions are optional and need not to be provided by every CMSIS-RTOS implementation.
+
+
+<b>Function calls from interrupt service routines</b>
+
+The following CMSIS-RTOS functions can be called from threads and interrupt service routines (ISR):
+ - \ref osSignalSet
+ - \ref osSemaphoreRelease
+ - \ref osPoolAlloc, \ref osPoolCAlloc, \ref osPoolFree
+ - \ref osMessagePut, \ref osMessageGet
+ - \ref osMailAlloc, \ref osMailCAlloc, \ref osMailGet, \ref osMailPut, \ref osMailFree
+
+Functions that cannot be called from an ISR are verifying the interrupt status and return in case that they are called
+from an ISR context the status code \b osErrorISR. In some implementations this condition might be caught using the HARD FAULT vector.
+
+Some CMSIS-RTOS implementations support CMSIS-RTOS function calls from multiple ISR at the same time.
+If this is impossible, the CMSIS-RTOS rejects calls by nested ISR functions with the status code \b osErrorISRRecursive.
+
+
+<b>Define and reference object definitions</b>
+
+With <b>\#define osObjectsExternal</b> objects are defined as external symbols. This allows to create a consistent header file
+that is used troughtout a project as shown below:
+
+<i>Header File</i>
+\code
+#include <cmsis_os.h> // CMSIS RTOS header file
+
+// Thread definition
+extern void thread_sample (void const *argument); // function prototype
+osThreadDef (thread_sample, osPriorityBelowNormal, 1, 100);
+
+// Pool definition
+osPoolDef(MyPool, 10, long);
+\endcode
+
+
+This header file defines all objects when included in a C/C++ source file. When <b>\#define osObjectsExternal</b> is
+present before the header file, the objects are defined as external symbols. A single consistent header file can therefore be
+used throughout the whole project.
+
+<i>Example</i>
+\code
+#include "osObjects.h" // Definition of the CMSIS-RTOS objects
+\endcode
+
+\code
+#define osObjectExternal // Objects will be defined as external symbols
+#include "osObjects.h" // Reference to the CMSIS-RTOS objects
+\endcode
+
+*/
+
+#ifndef _CMSIS_OS_H
+#define _CMSIS_OS_H
+
+/// \note MUST REMAIN UNCHANGED: \b osCMSIS identifies the CMSIS-RTOS API version.
+#define osCMSIS 0x10001 ///< API version (main [31:16] .sub [15:0])
+
+/// \note CAN BE CHANGED: \b osCMSIS_KERNEL identifies the underlaying RTOS kernel and version number.
+#define osCMSIS_RTX ((4<<16)|50) ///< RTOS identification and version (main [31:16] .sub [15:0])
+
+/// \note MUST REMAIN UNCHANGED: \b osKernelSystemId shall be consistent in every CMSIS-RTOS.
+#define osKernelSystemId "RTX V4.50" ///< RTOS identification string
+
+
+#define CMSIS_OS_RTX
+
+// The stack space occupied is mainly dependent on the underling C standard library
+#if defined(TOOLCHAIN_GCC_ARM) || defined(TOOLCHAIN_CS_ARM) || defined(TOOLCHAIN_CR_ARM)
+# define WORDS_STACK_SIZE 512
+#elif defined(TOOLCHAIN_ARM)
+# define WORDS_STACK_SIZE 512
+#elif defined(TOOLCHAIN_uARM)
+# define WORDS_STACK_SIZE 128
+#endif
+
+#define DEFAULT_STACK_SIZE (WORDS_STACK_SIZE*4)
+
+
+/// \note MUST REMAIN UNCHANGED: \b osFeature_xxx shall be consistent in every CMSIS-RTOS.
+#define osFeature_MainThread 1 ///< main thread 1=main can be thread, 0=not available
+#define osFeature_Pool 1 ///< Memory Pools: 1=available, 0=not available
+#define osFeature_MailQ 1 ///< Mail Queues: 1=available, 0=not available
+#define osFeature_MessageQ 1 ///< Message Queues: 1=available, 0=not available
+#define osFeature_Signals 16 ///< maximum number of Signal Flags available per thread
+#define osFeature_Semaphore 8 ///< maximum count for \ref osSemaphoreCreate function
+#define osFeature_Wait 0 ///< osWait function: 1=available, 0=not available
+
+#if defined (__CC_ARM)
+#define os_InRegs __value_in_regs // Compiler specific: force struct in registers
+#else
+#define os_InRegs
+#endif
+
+#include <stdint.h>
+#include <stddef.h>
+
+#ifdef __cplusplus
+extern "C"
+{
+#endif
+
+#include "os_tcb.h"
+
+// ==== Enumeration, structures, defines ====
+
+/// Priority used for thread control.
+/// \note MUST REMAIN UNCHANGED: \b osPriority shall be consistent in every CMSIS-RTOS.
+typedef enum {
+ osPriorityIdle = -3, ///< priority: idle (lowest)
+ osPriorityLow = -2, ///< priority: low
+ osPriorityBelowNormal = -1, ///< priority: below normal
+ osPriorityNormal = 0, ///< priority: normal (default)
+ osPriorityAboveNormal = +1, ///< priority: above normal
+ osPriorityHigh = +2, ///< priority: high
+ osPriorityRealtime = +3, ///< priority: realtime (highest)
+ osPriorityError = 0x84 ///< system cannot determine priority or thread has illegal priority
+} osPriority;
+
+/// Timeout value.
+/// \note MUST REMAIN UNCHANGED: \b osWaitForever shall be consistent in every CMSIS-RTOS.
+#define osWaitForever 0xFFFFFFFF ///< wait forever timeout value
+
+/// Status code values returned by CMSIS-RTOS functions.
+/// \note MUST REMAIN UNCHANGED: \b osStatus shall be consistent in every CMSIS-RTOS.
+typedef enum {
+ osOK = 0, ///< function completed; no event occurred.
+ osEventSignal = 0x08, ///< function completed; signal event occurred.
+ osEventMessage = 0x10, ///< function completed; message event occurred.
+ osEventMail = 0x20, ///< function completed; mail event occurred.
+ osEventTimeout = 0x40, ///< function completed; timeout occurred.
+ osErrorParameter = 0x80, ///< parameter error: a mandatory parameter was missing or specified an incorrect object.
+ osErrorResource = 0x81, ///< resource not available: a specified resource was not available.
+ osErrorTimeoutResource = 0xC1, ///< resource not available within given time: a specified resource was not available within the timeout period.
+ osErrorISR = 0x82, ///< not allowed in ISR context: the function cannot be called from interrupt service routines.
+ osErrorISRRecursive = 0x83, ///< function called multiple times from ISR with same object.
+ osErrorPriority = 0x84, ///< system cannot determine priority or thread has illegal priority.
+ osErrorNoMemory = 0x85, ///< system is out of memory: it was impossible to allocate or reserve memory for the operation.
+ osErrorValue = 0x86, ///< value of a parameter is out of range.
+ osErrorOS = 0xFF, ///< unspecified RTOS error: run-time error but no other error message fits.
+ os_status_reserved = 0x7FFFFFFF ///< prevent from enum down-size compiler optimization.
+} osStatus;
+
+
+/// Timer type value for the timer definition.
+/// \note MUST REMAIN UNCHANGED: \b os_timer_type shall be consistent in every CMSIS-RTOS.
+typedef enum {
+ osTimerOnce = 0, ///< one-shot timer
+ osTimerPeriodic = 1 ///< repeating timer
+} os_timer_type;
+
+/// Entry point of a thread.
+/// \note MUST REMAIN UNCHANGED: \b os_pthread shall be consistent in every CMSIS-RTOS.
+typedef void (*os_pthread) (void const *argument);
+
+/// Entry point of a timer call back function.
+/// \note MUST REMAIN UNCHANGED: \b os_ptimer shall be consistent in every CMSIS-RTOS.
+typedef void (*os_ptimer) (void const *argument);
+
+// >>> the following data type definitions may shall adapted towards a specific RTOS
+
+/// Thread ID identifies the thread (pointer to a thread control block).
+/// \note CAN BE CHANGED: \b os_thread_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_thread_cb *osThreadId;
+
+/// Timer ID identifies the timer (pointer to a timer control block).
+/// \note CAN BE CHANGED: \b os_timer_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_timer_cb *osTimerId;
+
+/// Mutex ID identifies the mutex (pointer to a mutex control block).
+/// \note CAN BE CHANGED: \b os_mutex_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_mutex_cb *osMutexId;
+
+/// Semaphore ID identifies the semaphore (pointer to a semaphore control block).
+/// \note CAN BE CHANGED: \b os_semaphore_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_semaphore_cb *osSemaphoreId;
+
+/// Pool ID identifies the memory pool (pointer to a memory pool control block).
+/// \note CAN BE CHANGED: \b os_pool_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_pool_cb *osPoolId;
+
+/// Message ID identifies the message queue (pointer to a message queue control block).
+/// \note CAN BE CHANGED: \b os_messageQ_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_messageQ_cb *osMessageQId;
+
+/// Mail ID identifies the mail queue (pointer to a mail queue control block).
+/// \note CAN BE CHANGED: \b os_mailQ_cb is implementation specific in every CMSIS-RTOS.
+typedef struct os_mailQ_cb *osMailQId;
+
+
+/// Thread Definition structure contains startup information of a thread.
+/// \note CAN BE CHANGED: \b os_thread_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_thread_def {
+ os_pthread pthread; ///< start address of thread function
+ osPriority tpriority; ///< initial thread priority
+ uint32_t stacksize; ///< stack size requirements in bytes
+ unsigned char *stack_pointer; ///< pointer to the stack memory block
+ struct OS_TCB tcb;
+} osThreadDef_t;
+
+/// Timer Definition structure contains timer parameters.
+/// \note CAN BE CHANGED: \b os_timer_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_timer_def {
+ os_ptimer ptimer; ///< start address of a timer function
+ void *timer; ///< pointer to internal data
+} osTimerDef_t;
+
+/// Mutex Definition structure contains setup information for a mutex.
+/// \note CAN BE CHANGED: \b os_mutex_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_mutex_def {
+ void *mutex; ///< pointer to internal data
+} osMutexDef_t;
+
+/// Semaphore Definition structure contains setup information for a semaphore.
+/// \note CAN BE CHANGED: \b os_semaphore_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_semaphore_def {
+ void *semaphore; ///< pointer to internal data
+} osSemaphoreDef_t;
+
+/// Definition structure for memory block allocation.
+/// \note CAN BE CHANGED: \b os_pool_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_pool_def {
+ uint32_t pool_sz; ///< number of items (elements) in the pool
+ uint32_t item_sz; ///< size of an item
+ void *pool; ///< pointer to memory for pool
+} osPoolDef_t;
+
+/// Definition structure for message queue.
+/// \note CAN BE CHANGED: \b os_messageQ_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_messageQ_def {
+ uint32_t queue_sz; ///< number of elements in the queue
+ void *pool; ///< memory array for messages
+} osMessageQDef_t;
+
+/// Definition structure for mail queue.
+/// \note CAN BE CHANGED: \b os_mailQ_def is implementation specific in every CMSIS-RTOS.
+typedef struct os_mailQ_def {
+ uint32_t queue_sz; ///< number of elements in the queue
+ uint32_t item_sz; ///< size of an item
+ void *pool; ///< memory array for mail
+} osMailQDef_t;
+
+/// Event structure contains detailed information about an event.
+/// \note MUST REMAIN UNCHANGED: \b os_event shall be consistent in every CMSIS-RTOS.
+/// However the struct may be extended at the end.
+typedef struct {
+ osStatus status; ///< status code: event or error information
+ union {
+ uint32_t v; ///< message as 32-bit value
+ void *p; ///< message or mail as void pointer
+ int32_t signals; ///< signal flags
+ } value; ///< event value
+ union {
+ osMailQId mail_id; ///< mail id obtained by \ref osMailCreate
+ osMessageQId message_id; ///< message id obtained by \ref osMessageCreate
+ } def; ///< event definition
+} osEvent;
+
+
+// ==== Kernel Control Functions ====
+
+/// Initialize the RTOS Kernel for creating objects.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osKernelInitialize shall be consistent in every CMSIS-RTOS.
+osStatus osKernelInitialize (void);
+
+/// Start the RTOS Kernel.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osKernelStart shall be consistent in every CMSIS-RTOS.
+osStatus osKernelStart (void);
+
+/// Check if the RTOS kernel is already started.
+/// \note MUST REMAIN UNCHANGED: \b osKernelRunning shall be consistent in every CMSIS-RTOS.
+/// \return 0 RTOS is not started, 1 RTOS is started.
+int32_t osKernelRunning(void);
+
+
+// ==== Thread Management ====
+
+/// Create a Thread Definition with function, priority, and stack requirements.
+/// \param name name of the thread function.
+/// \param priority initial priority of the thread function.
+/// \param stacksz stack size (in bytes) requirements for the thread function.
+/// \note CAN BE CHANGED: The parameters to \b osThreadDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osThreadDef(name, priority, stacksz) \
+extern osThreadDef_t os_thread_def_##name
+#else // define the object
+#define osThreadDef(name, priority, stacksz) \
+unsigned char os_thread_def_stack_##name [stacksz]; \
+osThreadDef_t os_thread_def_##name = \
+{ (name), (priority), (stacksz), (os_thread_def_stack_##name)}
+#endif
+
+/// Access a Thread defintion.
+/// \param name name of the thread definition object.
+/// \note CAN BE CHANGED: The parameter to \b osThread shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osThread(name) \
+&os_thread_def_##name
+
+/// Create a thread and add it to Active Threads and set it to state READY.
+/// \param[in] thread_def thread definition referenced with \ref osThread.
+/// \param[in] argument pointer that is passed to the thread function as start argument.
+/// \return thread ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osThreadCreate shall be consistent in every CMSIS-RTOS.
+osThreadId osThreadCreate (osThreadDef_t *thread_def, void *argument);
+
+/// Return the thread ID of the current running thread.
+/// \return thread ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osThreadGetId shall be consistent in every CMSIS-RTOS.
+osThreadId osThreadGetId (void);
+
+/// Terminate execution of a thread and remove it from Active Threads.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osThreadTerminate shall be consistent in every CMSIS-RTOS.
+osStatus osThreadTerminate (osThreadId thread_id);
+
+/// Pass control to next thread that is in state \b READY.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osThreadYield shall be consistent in every CMSIS-RTOS.
+osStatus osThreadYield (void);
+
+/// Change priority of an active thread.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \param[in] priority new priority value for the thread function.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osThreadSetPriority shall be consistent in every CMSIS-RTOS.
+osStatus osThreadSetPriority (osThreadId thread_id, osPriority priority);
+
+/// Get current priority of an active thread.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \return current priority value of the thread function.
+/// \note MUST REMAIN UNCHANGED: \b osThreadGetPriority shall be consistent in every CMSIS-RTOS.
+osPriority osThreadGetPriority (osThreadId thread_id);
+
+
+// ==== Generic Wait Functions ====
+
+/// Wait for Timeout (Time Delay).
+/// \param[in] millisec time delay value
+/// \return status code that indicates the execution status of the function.
+osStatus osDelay (uint32_t millisec);
+
+#if (defined (osFeature_Wait) && (osFeature_Wait != 0)) // Generic Wait available
+
+/// Wait for Signal, Message, Mail, or Timeout.
+/// \param[in] millisec timeout value or 0 in case of no time-out
+/// \return event that contains signal, message, or mail information or error code.
+/// \note MUST REMAIN UNCHANGED: \b osWait shall be consistent in every CMSIS-RTOS.
+os_InRegs osEvent osWait (uint32_t millisec);
+
+#endif // Generic Wait available
+
+
+// ==== Timer Management Functions ====
+/// Define a Timer object.
+/// \param name name of the timer object.
+/// \param function name of the timer call back function.
+/// \note CAN BE CHANGED: The parameter to \b osTimerDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osTimerDef(name, function) \
+extern osTimerDef_t os_timer_def_##name
+#else // define the object
+#define osTimerDef(name, function) \
+uint32_t os_timer_cb_##name[5]; \
+osTimerDef_t os_timer_def_##name = \
+{ (function), (os_timer_cb_##name) }
+#endif
+
+/// Access a Timer definition.
+/// \param name name of the timer object.
+/// \note CAN BE CHANGED: The parameter to \b osTimer shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osTimer(name) \
+&os_timer_def_##name
+
+/// Create a timer.
+/// \param[in] timer_def timer object referenced with \ref osTimer.
+/// \param[in] type osTimerOnce for one-shot or osTimerPeriodic for periodic behavior.
+/// \param[in] argument argument to the timer call back function.
+/// \return timer ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osTimerCreate shall be consistent in every CMSIS-RTOS.
+osTimerId osTimerCreate (osTimerDef_t *timer_def, os_timer_type type, void *argument);
+
+/// Start or restart a timer.
+/// \param[in] timer_id timer ID obtained by \ref osTimerCreate.
+/// \param[in] millisec time delay value of the timer.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osTimerStart shall be consistent in every CMSIS-RTOS.
+osStatus osTimerStart (osTimerId timer_id, uint32_t millisec);
+
+/// Stop the timer.
+/// \param[in] timer_id timer ID obtained by \ref osTimerCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osTimerStop shall be consistent in every CMSIS-RTOS.
+osStatus osTimerStop (osTimerId timer_id);
+
+/// Delete a timer that was created by \ref osTimerCreate.
+/// \param[in] timer_id timer ID obtained by \ref osTimerCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osTimerDelete shall be consistent in every CMSIS-RTOS.
+osStatus osTimerDelete (osTimerId timer_id);
+
+
+// ==== Signal Management ====
+
+/// Set the specified Signal Flags of an active thread.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \param[in] signals specifies the signal flags of the thread that should be set.
+/// \return previous signal flags of the specified thread or 0x80000000 in case of incorrect parameters.
+/// \note MUST REMAIN UNCHANGED: \b osSignalSet shall be consistent in every CMSIS-RTOS.
+int32_t osSignalSet (osThreadId thread_id, int32_t signal);
+
+/// Clear the specified Signal Flags of an active thread.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \param[in] signals specifies the signal flags of the thread that shall be cleared.
+/// \return previous signal flags of the specified thread or 0x80000000 in case of incorrect parameters.
+/// \note MUST REMAIN UNCHANGED: \b osSignalClear shall be consistent in every CMSIS-RTOS.
+int32_t osSignalClear (osThreadId thread_id, int32_t signal);
+
+/// Get Signal Flags status of an active thread.
+/// \param[in] thread_id thread ID obtained by \ref osThreadCreate or \ref osThreadGetId.
+/// \return previous signal flags of the specified thread or 0x80000000 in case of incorrect parameters.
+/// \note MUST REMAIN UNCHANGED: \b osSignalGet shall be consistent in every CMSIS-RTOS.
+int32_t osSignalGet (osThreadId thread_id);
+
+/// Wait for one or more Signal Flags to become signaled for the current \b RUNNING thread.
+/// \param[in] signals wait until all specified signal flags set or 0 for any single signal flag.
+/// \param[in] millisec timeout value or 0 in case of no time-out.
+/// \return event flag information or error code.
+/// \note MUST REMAIN UNCHANGED: \b osSignalWait shall be consistent in every CMSIS-RTOS.
+os_InRegs osEvent osSignalWait (int32_t signals, uint32_t millisec);
+
+
+// ==== Mutex Management ====
+
+/// Define a Mutex.
+/// \param name name of the mutex object.
+/// \note CAN BE CHANGED: The parameter to \b osMutexDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osMutexDef(name) \
+extern osMutexDef_t os_mutex_def_##name
+#else // define the object
+#define osMutexDef(name) \
+uint32_t os_mutex_cb_##name[3]; \
+osMutexDef_t os_mutex_def_##name = { (os_mutex_cb_##name) }
+#endif
+
+/// Access a Mutex defintion.
+/// \param name name of the mutex object.
+/// \note CAN BE CHANGED: The parameter to \b osMutex shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osMutex(name) \
+&os_mutex_def_##name
+
+/// Create and Initialize a Mutex object.
+/// \param[in] mutex_def mutex definition referenced with \ref osMutex.
+/// \return mutex ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osMutexCreate shall be consistent in every CMSIS-RTOS.
+osMutexId osMutexCreate (osMutexDef_t *mutex_def);
+
+/// Wait until a Mutex becomes available.
+/// \param[in] mutex_id mutex ID obtained by \ref osMutexCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMutexWait shall be consistent in every CMSIS-RTOS.
+osStatus osMutexWait (osMutexId mutex_id, uint32_t millisec);
+
+/// Release a Mutex that was obtained by \ref osMutexWait.
+/// \param[in] mutex_id mutex ID obtained by \ref osMutexCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMutexRelease shall be consistent in every CMSIS-RTOS.
+osStatus osMutexRelease (osMutexId mutex_id);
+
+/// Delete a Mutex that was created by \ref osMutexCreate.
+/// \param[in] mutex_id mutex ID obtained by \ref osMutexCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMutexDelete shall be consistent in every CMSIS-RTOS.
+osStatus osMutexDelete (osMutexId mutex_id);
+
+
+// ==== Semaphore Management Functions ====
+
+#if (defined (osFeature_Semaphore) && (osFeature_Semaphore != 0)) // Semaphore available
+
+/// Define a Semaphore object.
+/// \param name name of the semaphore object.
+/// \note CAN BE CHANGED: The parameter to \b osSemaphoreDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osSemaphoreDef(name) \
+extern osSemaphoreDef_t os_semaphore_def_##name
+#else // define the object
+#define osSemaphoreDef(name) \
+uint32_t os_semaphore_cb_##name[2]; \
+osSemaphoreDef_t os_semaphore_def_##name = { (os_semaphore_cb_##name) }
+#endif
+
+/// Access a Semaphore definition.
+/// \param name name of the semaphore object.
+/// \note CAN BE CHANGED: The parameter to \b osSemaphore shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osSemaphore(name) \
+&os_semaphore_def_##name
+
+/// Create and Initialize a Semaphore object used for managing resources.
+/// \param[in] semaphore_def semaphore definition referenced with \ref osSemaphore.
+/// \param[in] count number of available resources.
+/// \return semaphore ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osSemaphoreCreate shall be consistent in every CMSIS-RTOS.
+osSemaphoreId osSemaphoreCreate (osSemaphoreDef_t *semaphore_def, int32_t count);
+
+/// Wait until a Semaphore token becomes available.
+/// \param[in] semaphore_id semaphore object referenced with \ref osSemaphoreCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out.
+/// \return number of available tokens, or -1 in case of incorrect parameters.
+/// \note MUST REMAIN UNCHANGED: \b osSemaphoreWait shall be consistent in every CMSIS-RTOS.
+int32_t osSemaphoreWait (osSemaphoreId semaphore_id, uint32_t millisec);
+
+/// Release a Semaphore token.
+/// \param[in] semaphore_id semaphore object referenced with \ref osSemaphoreCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osSemaphoreRelease shall be consistent in every CMSIS-RTOS.
+osStatus osSemaphoreRelease (osSemaphoreId semaphore_id);
+
+/// Delete a Semaphore that was created by \ref osSemaphoreCreate.
+/// \param[in] semaphore_id semaphore object referenced with \ref osSemaphoreCreate.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osSemaphoreDelete shall be consistent in every CMSIS-RTOS.
+osStatus osSemaphoreDelete (osSemaphoreId semaphore_id);
+
+#endif // Semaphore available
+
+
+// ==== Memory Pool Management Functions ====
+
+#if (defined (osFeature_Pool) && (osFeature_Pool != 0)) // Memory Pool Management available
+
+/// \brief Define a Memory Pool.
+/// \param name name of the memory pool.
+/// \param no maximum number of blocks (objects) in the memory pool.
+/// \param type data type of a single block (object).
+/// \note CAN BE CHANGED: The parameter to \b osPoolDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osPoolDef(name, no, type) \
+extern osPoolDef_t os_pool_def_##name
+#else // define the object
+#define osPoolDef(name, no, type) \
+uint32_t os_pool_m_##name[3+((sizeof(type)+3)/4)*(no)]; \
+osPoolDef_t os_pool_def_##name = \
+{ (no), sizeof(type), (os_pool_m_##name) }
+#endif
+
+/// \brief Access a Memory Pool definition.
+/// \param name name of the memory pool
+/// \note CAN BE CHANGED: The parameter to \b osPool shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osPool(name) \
+&os_pool_def_##name
+
+/// Create and Initialize a memory pool.
+/// \param[in] pool_def memory pool definition referenced with \ref osPool.
+/// \return memory pool ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osPoolCreate shall be consistent in every CMSIS-RTOS.
+osPoolId osPoolCreate (osPoolDef_t *pool_def);
+
+/// Allocate a memory block from a memory pool.
+/// \param[in] pool_id memory pool ID obtain referenced with \ref osPoolCreate.
+/// \return address of the allocated memory block or NULL in case of no memory available.
+/// \note MUST REMAIN UNCHANGED: \b osPoolAlloc shall be consistent in every CMSIS-RTOS.
+void *osPoolAlloc (osPoolId pool_id);
+
+/// Allocate a memory block from a memory pool and set memory block to zero.
+/// \param[in] pool_id memory pool ID obtain referenced with \ref osPoolCreate.
+/// \return address of the allocated memory block or NULL in case of no memory available.
+/// \note MUST REMAIN UNCHANGED: \b osPoolCAlloc shall be consistent in every CMSIS-RTOS.
+void *osPoolCAlloc (osPoolId pool_id);
+
+/// Return an allocated memory block back to a specific memory pool.
+/// \param[in] pool_id memory pool ID obtain referenced with \ref osPoolCreate.
+/// \param[in] block address of the allocated memory block that is returned to the memory pool.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osPoolFree shall be consistent in every CMSIS-RTOS.
+osStatus osPoolFree (osPoolId pool_id, void *block);
+
+#endif // Memory Pool Management available
+
+
+// ==== Message Queue Management Functions ====
+
+#if (defined (osFeature_MessageQ) && (osFeature_MessageQ != 0)) // Message Queues available
+
+/// \brief Create a Message Queue Definition.
+/// \param name name of the queue.
+/// \param queue_sz maximum number of messages in the queue.
+/// \param type data type of a single message element (for debugger).
+/// \note CAN BE CHANGED: The parameter to \b osMessageQDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osMessageQDef(name, queue_sz, type) \
+extern osMessageQDef_t os_messageQ_def_##name
+#else // define the object
+#define osMessageQDef(name, queue_sz, type) \
+uint32_t os_messageQ_q_##name[4+(queue_sz)]; \
+osMessageQDef_t os_messageQ_def_##name = \
+{ (queue_sz), (os_messageQ_q_##name) }
+#endif
+
+/// \brief Access a Message Queue Definition.
+/// \param name name of the queue
+/// \note CAN BE CHANGED: The parameter to \b osMessageQ shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osMessageQ(name) \
+&os_messageQ_def_##name
+
+/// Create and Initialize a Message Queue.
+/// \param[in] queue_def queue definition referenced with \ref osMessageQ.
+/// \param[in] thread_id thread ID (obtained by \ref osThreadCreate or \ref osThreadGetId) or NULL.
+/// \return message queue ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osMessageCreate shall be consistent in every CMSIS-RTOS.
+osMessageQId osMessageCreate (osMessageQDef_t *queue_def, osThreadId thread_id);
+
+/// Put a Message to a Queue.
+/// \param[in] queue_id message queue ID obtained with \ref osMessageCreate.
+/// \param[in] info message information.
+/// \param[in] millisec timeout value or 0 in case of no time-out.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMessagePut shall be consistent in every CMSIS-RTOS.
+osStatus osMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec);
+
+/// Get a Message or Wait for a Message from a Queue.
+/// \param[in] queue_id message queue ID obtained with \ref osMessageCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out.
+/// \return event information that includes status code.
+/// \note MUST REMAIN UNCHANGED: \b osMessageGet shall be consistent in every CMSIS-RTOS.
+os_InRegs osEvent osMessageGet (osMessageQId queue_id, uint32_t millisec);
+
+#endif // Message Queues available
+
+
+// ==== Mail Queue Management Functions ====
+
+#if (defined (osFeature_MailQ) && (osFeature_MailQ != 0)) // Mail Queues available
+
+/// \brief Create a Mail Queue Definition.
+/// \param name name of the queue
+/// \param queue_sz maximum number of messages in queue
+/// \param type data type of a single message element
+/// \note CAN BE CHANGED: The parameter to \b osMailQDef shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#if defined (osObjectsExternal) // object is external
+#define osMailQDef(name, queue_sz, type) \
+extern osMailQDef_t os_mailQ_def_##name
+#else // define the object
+#define osMailQDef(name, queue_sz, type) \
+uint32_t os_mailQ_q_##name[4+(queue_sz)]; \
+uint32_t os_mailQ_m_##name[3+((sizeof(type)+3)/4)*(queue_sz)]; \
+void * os_mailQ_p_##name[2] = { (os_mailQ_q_##name), os_mailQ_m_##name }; \
+osMailQDef_t os_mailQ_def_##name = \
+{ (queue_sz), sizeof(type), (os_mailQ_p_##name) }
+#endif
+
+/// \brief Access a Mail Queue Definition.
+/// \param name name of the queue
+/// \note CAN BE CHANGED: The parameter to \b osMailQ shall be consistent but the
+/// macro body is implementation specific in every CMSIS-RTOS.
+#define osMailQ(name) \
+&os_mailQ_def_##name
+
+/// Create and Initialize mail queue.
+/// \param[in] queue_def reference to the mail queue definition obtain with \ref osMailQ
+/// \param[in] thread_id thread ID (obtained by \ref osThreadCreate or \ref osThreadGetId) or NULL.
+/// \return mail queue ID for reference by other functions or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osMailCreate shall be consistent in every CMSIS-RTOS.
+osMailQId osMailCreate (osMailQDef_t *queue_def, osThreadId thread_id);
+
+/// Allocate a memory block from a mail.
+/// \param[in] queue_id mail queue ID obtained with \ref osMailCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out
+/// \return pointer to memory block that can be filled with mail or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osMailAlloc shall be consistent in every CMSIS-RTOS.
+void *osMailAlloc (osMailQId queue_id, uint32_t millisec);
+
+/// Allocate a memory block from a mail and set memory block to zero.
+/// \param[in] queue_id mail queue ID obtained with \ref osMailCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out
+/// \return pointer to memory block that can be filled with mail or NULL in case of error.
+/// \note MUST REMAIN UNCHANGED: \b osMailCAlloc shall be consistent in every CMSIS-RTOS.
+void *osMailCAlloc (osMailQId queue_id, uint32_t millisec);
+
+/// Put a mail to a queue.
+/// \param[in] queue_id mail queue ID obtained with \ref osMailCreate.
+/// \param[in] mail memory block previously allocated with \ref osMailAlloc or \ref osMailCAlloc.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMailPut shall be consistent in every CMSIS-RTOS.
+osStatus osMailPut (osMailQId queue_id, void *mail);
+
+/// Get a mail from a queue.
+/// \param[in] queue_id mail queue ID obtained with \ref osMailCreate.
+/// \param[in] millisec timeout value or 0 in case of no time-out
+/// \return event that contains mail information or error code.
+/// \note MUST REMAIN UNCHANGED: \b osMailGet shall be consistent in every CMSIS-RTOS.
+os_InRegs osEvent osMailGet (osMailQId queue_id, uint32_t millisec);
+
+/// Free a memory block from a mail.
+/// \param[in] queue_id mail queue ID obtained with \ref osMailCreate.
+/// \param[in] mail pointer to the memory block that was obtained with \ref osMailGet.
+/// \return status code that indicates the execution status of the function.
+/// \note MUST REMAIN UNCHANGED: \b osMailFree shall be consistent in every CMSIS-RTOS.
+osStatus osMailFree (osMailQId queue_id, void *mail);
+
+#endif // Mail Queues available
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif // _CMSIS_OS_H
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/os_tcb.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,50 @@
+#ifndef OS_TCB_H
+#define OS_TCB_H
+
+/* Types */
+typedef char S8;
+typedef unsigned char U8;
+typedef short S16;
+typedef unsigned short U16;
+typedef int S32;
+typedef unsigned int U32;
+typedef long long S64;
+typedef unsigned long long U64;
+typedef unsigned char BIT;
+typedef unsigned int BOOL;
+typedef void (*FUNCP)(void);
+
+typedef struct OS_TCB {
+ /* General part: identical for all implementations. */
+ U8 cb_type; /* Control Block Type */
+ U8 state; /* Task state */
+ U8 prio; /* Execution priority */
+ U8 task_id; /* Task ID value for optimized TCB access */
+ struct OS_TCB *p_lnk; /* Link pointer for ready/sem. wait list */
+ struct OS_TCB *p_rlnk; /* Link pointer for sem./mbx lst backwards */
+ struct OS_TCB *p_dlnk; /* Link pointer for delay list */
+ struct OS_TCB *p_blnk; /* Link pointer for delay list backwards */
+ U16 delta_time; /* Time until time out */
+ U16 interval_time; /* Time interval for periodic waits */
+ U16 events; /* Event flags */
+ U16 waits; /* Wait flags */
+ void **msg; /* Direct message passing when task waits */
+
+ /* Hardware dependant part: specific for CM processor */
+ U8 stack_frame; /* Stack frame: 0=Basic, 1=Extended */
+ U8 reserved;
+ U16 priv_stack; /* Private stack size in bytes */
+ U32 tsk_stack; /* Current task Stack pointer (R13) */
+ U32 *stack; /* Pointer to Task Stack memory block */
+
+ /* Library dependant part */
+#if defined (__CC_ARM) && !defined (__MICROLIB)
+ /* A memory space for arm standard library. */
+ U32 std_libspace[96/4];
+#endif
+
+ /* Task entry point used for uVision debugger */
+ FUNCP ptask; /* Task entry address */
+} *P_TCB;
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_CMSIS.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,1913 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: rt_CMSIS.c
+ * Purpose: CMSIS RTOS API
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#define __CMSIS_GENERIC
+
+#if defined (__CORTEX_M4) || defined (__CORTEX_M4F)
+ #include "core_cm4.h"
+#elif defined (__CORTEX_M3)
+ #include "core_cm3.h"
+#elif defined (__CORTEX_M0)
+ #include "core_cm0.h"
+#else
+ #error "Missing __CORTEX_Mx definition"
+#endif
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_Task.h"
+#include "rt_Event.h"
+#include "rt_List.h"
+#include "rt_Time.h"
+#include "rt_Mutex.h"
+#include "rt_Semaphore.h"
+#include "rt_Mailbox.h"
+#include "rt_MemBox.h"
+#include "rt_HAL_CM.h"
+
+#define os_thread_cb OS_TCB
+
+#include "cmsis_os.h"
+
+#if (osFeature_Signals != 16)
+#error Invalid "osFeature_Signals" value!
+#endif
+#if (osFeature_Semaphore != 8)
+#error Invalid "osFeature_Semaphore" value!
+#endif
+#if (osFeature_Wait != 0)
+#error osWait not supported!
+#endif
+
+
+// ==== Enumeration, structures, defines ====
+
+// Service Calls defines
+
+#if defined (__CC_ARM) /* ARM Compiler */
+
+#define __NO_RETURN __declspec(noreturn)
+
+#define osEvent_type osEvent
+#define osEvent_ret_status ret
+#define osEvent_ret_value ret
+#define osEvent_ret_msg ret
+#define osEvent_ret_mail ret
+
+#define osCallback_type osCallback
+#define osCallback_ret ret
+
+#define SVC_0_1(f,t,...) \
+__svc_indirect(0) t _##f (t(*)()); \
+ t f (void); \
+__attribute__((always_inline)) \
+static __inline t __##f (void) { \
+ return _##f(f); \
+}
+
+#define SVC_1_1(f,t,t1,...) \
+__svc_indirect(0) t _##f (t(*)(t1),t1); \
+ t f (t1 a1); \
+__attribute__((always_inline)) \
+static __inline t __##f (t1 a1) { \
+ return _##f(f,a1); \
+}
+
+#define SVC_2_1(f,t,t1,t2,...) \
+__svc_indirect(0) t _##f (t(*)(t1,t2),t1,t2); \
+ t f (t1 a1, t2 a2); \
+__attribute__((always_inline)) \
+static __inline t __##f (t1 a1, t2 a2) { \
+ return _##f(f,a1,a2); \
+}
+
+#define SVC_3_1(f,t,t1,t2,t3,...) \
+__svc_indirect(0) t _##f (t(*)(t1,t2,t3),t1,t2,t3); \
+ t f (t1 a1, t2 a2, t3 a3); \
+__attribute__((always_inline)) \
+static __inline t __##f (t1 a1, t2 a2, t3 a3) { \
+ return _##f(f,a1,a2,a3); \
+}
+
+#define SVC_4_1(f,t,t1,t2,t3,t4,...) \
+__svc_indirect(0) t _##f (t(*)(t1,t2,t3,t4),t1,t2,t3,t4); \
+ t f (t1 a1, t2 a2, t3 a3, t4 a4); \
+__attribute__((always_inline)) \
+static __inline t __##f (t1 a1, t2 a2, t3 a3, t4 a4) { \
+ return _##f(f,a1,a2,a3,a4); \
+}
+
+#define SVC_1_2 SVC_1_1
+#define SVC_1_3 SVC_1_1
+#define SVC_2_3 SVC_2_1
+
+#elif defined (__GNUC__) /* GNU Compiler */
+
+#define __NO_RETURN __attribute__((noreturn))
+
+typedef uint32_t __attribute__((vector_size(8))) ret64;
+typedef uint32_t __attribute__((vector_size(16))) ret128;
+
+#define RET_pointer __r0
+#define RET_int32_t __r0
+#define RET_osStatus __r0
+#define RET_osPriority __r0
+#define RET_osEvent {(osStatus)__r0, {(uint32_t)__r1}, {(void *)__r2}}
+#define RET_osCallback {(void *)__r0, (void *)__r1}
+
+#define osEvent_type ret128
+#define osEvent_ret_status (ret128){ret.status}
+#define osEvent_ret_value (ret128){ret.status, ret.value.v}
+#define osEvent_ret_msg (ret128){ret.status, ret.value.v, (uint32_t)ret.def.message_id}
+#define osEvent_ret_mail (ret128){ret.status, ret.value.v, (uint32_t)ret.def.mail_id}
+
+#define osCallback_type ret64
+#define osCallback_ret (ret64) {(uint32_t)ret.fp, (uint32_t)ret.arg}
+
+#define SVC_ArgN(n) \
+ register int __r##n __asm("r"#n);
+
+#define SVC_ArgR(n,t,a) \
+ register t __r##n __asm("r"#n) = a;
+
+#define SVC_Arg0() \
+ SVC_ArgN(0) \
+ SVC_ArgN(1) \
+ SVC_ArgN(2) \
+ SVC_ArgN(3)
+
+#define SVC_Arg1(t1) \
+ SVC_ArgR(0,t1,a1) \
+ SVC_ArgN(1) \
+ SVC_ArgN(2) \
+ SVC_ArgN(3)
+
+#define SVC_Arg2(t1,t2) \
+ SVC_ArgR(0,t1,a1) \
+ SVC_ArgR(1,t2,a2) \
+ SVC_ArgN(2) \
+ SVC_ArgN(3)
+
+#define SVC_Arg3(t1,t2,t3) \
+ SVC_ArgR(0,t1,a1) \
+ SVC_ArgR(1,t2,a2) \
+ SVC_ArgR(2,t3,a3) \
+ SVC_ArgN(3)
+
+#define SVC_Arg4(t1,t2,t3,t4) \
+ SVC_ArgR(0,t1,a1) \
+ SVC_ArgR(1,t2,a2) \
+ SVC_ArgR(2,t3,a3) \
+ SVC_ArgR(3,t4,a4)
+
+#if (defined (__CORTEX_M0))
+#define SVC_Call(f) \
+ __asm volatile \
+ ( \
+ "ldr r7,="#f"\n\t" \
+ "mov r12,r7\n\t" \
+ "svc 0" \
+ : "=r" (__r0), "=r" (__r1), "=r" (__r2), "=r" (__r3) \
+ : "r" (__r0), "r" (__r1), "r" (__r2), "r" (__r3) \
+ : "r7", "r12", "lr", "cc" \
+ );
+#else
+#define SVC_Call(f) \
+ __asm volatile \
+ ( \
+ "ldr r12,="#f"\n\t" \
+ "svc 0" \
+ : "=r" (__r0), "=r" (__r1), "=r" (__r2), "=r" (__r3) \
+ : "r" (__r0), "r" (__r1), "r" (__r2), "r" (__r3) \
+ : "r12", "lr", "cc" \
+ );
+#endif
+
+#define SVC_0_1(f,t,rv) \
+__attribute__((always_inline)) \
+static inline t __##f (void) { \
+ SVC_Arg0(); \
+ SVC_Call(f); \
+ return (t) rv; \
+}
+
+#define SVC_1_1(f,t,t1,rv) \
+__attribute__((always_inline)) \
+static inline t __##f (t1 a1) { \
+ SVC_Arg1(t1); \
+ SVC_Call(f); \
+ return (t) rv; \
+}
+
+#define SVC_2_1(f,t,t1,t2,rv) \
+__attribute__((always_inline)) \
+static inline t __##f (t1 a1, t2 a2) { \
+ SVC_Arg2(t1,t2); \
+ SVC_Call(f); \
+ return (t) rv; \
+}
+
+#define SVC_3_1(f,t,t1,t2,t3,rv) \
+__attribute__((always_inline)) \
+static inline t __##f (t1 a1, t2 a2, t3 a3) { \
+ SVC_Arg3(t1,t2,t3); \
+ SVC_Call(f); \
+ return (t) rv; \
+}
+
+#define SVC_4_1(f,t,t1,t2,t3,t4,rv) \
+__attribute__((always_inline)) \
+static inline t __##f (t1 a1, t2 a2, t3 a3, t4 a4) { \
+ SVC_Arg4(t1,t2,t3,t4); \
+ SVC_Call(f); \
+ return (t) rv; \
+}
+
+#define SVC_1_2 SVC_1_1
+#define SVC_1_3 SVC_1_1
+#define SVC_2_3 SVC_2_1
+
+#elif defined (__ICCARM__) /* IAR Compiler */
+
+#define __NO_RETURN __noreturn
+
+#define RET_osEvent "=r"(ret.status), "=r"(ret.value), "=r"(ret.def)
+#define RET_osCallback "=r"(ret.fp), "=r"(ret.arg)
+
+#define osEvent_type osEvent
+#define osEvent_ret_status ret
+#define osEvent_ret_value ret
+#define osEvent_ret_msg ret
+#define osEvent_ret_mail ret
+
+#define osCallback_type uint64_t
+#define osCallback_ret ((uint64_t)ret.fp | ((uint64_t)ret.arg)<<32)
+
+#define SVC_Setup(f) \
+ __asm( \
+ "mov r12,%0\n" \
+ :: "r"(&f): "r12" \
+ );
+
+#define SVC_Ret3() \
+ __asm( \
+ "ldr r0,[sp,#0]\n" \
+ "ldr r1,[sp,#4]\n" \
+ "ldr r2,[sp,#8]\n" \
+ );
+
+#define SVC_0_1(f,t,...) \
+t f (void); \
+_Pragma("swi_number=0") __swi t _##f (void); \
+static inline t __##f (void) { \
+ SVC_Setup(f); \
+ return _##f(); \
+}
+
+#define SVC_1_1(f,t,t1,...) \
+t f (t1 a1); \
+_Pragma("swi_number=0") __swi t _##f (t1 a1); \
+static inline t __##f (t1 a1) { \
+ SVC_Setup(f); \
+ return _##f(a1); \
+}
+
+#define SVC_2_1(f,t,t1,t2,...) \
+t f (t1 a1, t2 a2); \
+_Pragma("swi_number=0") __swi t _##f (t1 a1, t2 a2); \
+static inline t __##f (t1 a1, t2 a2) { \
+ SVC_Setup(f); \
+ return _##f(a1,a2); \
+}
+
+#define SVC_3_1(f,t,t1,t2,t3,...) \
+t f (t1 a1, t2 a2, t3 a3); \
+_Pragma("swi_number=0") __swi t _##f (t1 a1, t2 a2, t3 a3); \
+static inline t __##f (t1 a1, t2 a2, t3 a3) { \
+ SVC_Setup(f); \
+ return _##f(a1,a2,a3); \
+}
+
+#define SVC_4_1(f,t,t1,t2,t3,t4,...) \
+t f (t1 a1, t2 a2, t3 a3, t4 a4); \
+_Pragma("swi_number=0") __swi t _##f (t1 a1, t2 a2, t3 a3, t4 a4); \
+static inline t __##f (t1 a1, t2 a2, t3 a3, t4 a4) { \
+ SVC_Setup(f); \
+ return _##f(a1,a2,a3,a4); \
+}
+
+#define SVC_1_2(f,t,t1,rr) \
+uint64_t f (t1 a1); \
+_Pragma("swi_number=0") __swi uint64_t _##f (t1 a1); \
+static inline t __##f (t1 a1) { \
+ t ret; \
+ SVC_Setup(f); \
+ _##f(a1); \
+ __asm("" : rr : :); \
+ return ret; \
+}
+
+#define SVC_1_3(f,t,t1,rr) \
+t f (t1 a1); \
+void f##_ (t1 a1) { \
+ f(a1); \
+ SVC_Ret3(); \
+} \
+_Pragma("swi_number=0") __swi void _##f (t1 a1); \
+static inline t __##f (t1 a1) { \
+ t ret; \
+ SVC_Setup(f##_); \
+ _##f(a1); \
+ __asm("" : rr : :); \
+ return ret; \
+}
+
+#define SVC_2_3(f,t,t1,t2,rr) \
+t f (t1 a1, t2 a2); \
+void f##_ (t1 a1, t2 a2) { \
+ f(a1,a2); \
+ SVC_Ret3(); \
+} \
+_Pragma("swi_number=0") __swi void _##f (t1 a1, t2 a2); \
+static inline t __##f (t1 a1, t2 a2) { \
+ t ret; \
+ SVC_Setup(f##_); \
+ _##f(a1,a2); \
+ __asm("" : rr : :); \
+ return ret; \
+}
+
+#endif
+
+
+// Callback structure
+typedef struct {
+ void *fp; // Function pointer
+ void *arg; // Function argument
+} osCallback;
+
+
+// OS Section definitions
+#ifdef OS_SECTIONS_LINK_INFO
+extern const uint32_t os_section_id$$Base;
+extern const uint32_t os_section_id$$Limit;
+#endif
+
+// OS Timers external resources
+extern osThreadDef_t os_thread_def_osTimerThread;
+extern osThreadId osThreadId_osTimerThread;
+extern osMessageQDef_t os_messageQ_def_osTimerMessageQ;
+extern osMessageQId osMessageQId_osTimerMessageQ;
+
+
+// ==== Helper Functions ====
+
+/// Convert timeout in millisec to system ticks
+static uint32_t rt_ms2tick (uint32_t millisec) {
+ uint32_t tick;
+
+ if (millisec == osWaitForever) return 0xFFFF; // Indefinite timeout
+ if (millisec > 4000000) return 0xFFFE; // Max ticks supported
+
+ tick = ((1000 * millisec) + os_clockrate - 1) / os_clockrate;
+ if (tick > 0xFFFE) return 0xFFFE;
+
+ return tick;
+}
+
+/// Convert Thread ID to TCB pointer
+static P_TCB rt_tid2ptcb (osThreadId thread_id) {
+ P_TCB ptcb;
+
+ if (thread_id == NULL) return NULL;
+
+ if ((uint32_t)thread_id & 3) return NULL;
+
+#ifdef OS_SECTIONS_LINK_INFO
+ if ((os_section_id$$Base != 0) && (os_section_id$$Limit != 0)) {
+ if (thread_id < (osThreadId)os_section_id$$Base) return NULL;
+ if (thread_id >= (osThreadId)os_section_id$$Limit) return NULL;
+ }
+#endif
+
+ ptcb = thread_id;
+
+ if (ptcb->cb_type != TCB) return NULL;
+
+ return ptcb;
+}
+
+/// Convert ID pointer to Object pointer
+static void *rt_id2obj (void *id) {
+
+ if ((uint32_t)id & 3) return NULL;
+
+#ifdef OS_SECTIONS_LINK_INFO
+ if ((os_section_id$$Base != 0) && (os_section_id$$Limit != 0)) {
+ if (id < (void *)os_section_id$$Base) return NULL;
+ if (id >= (void *)os_section_id$$Limit) return NULL;
+ }
+#endif
+
+ return id;
+}
+
+
+// ==== Kernel Control ====
+
+uint8_t os_initialized; // Kernel Initialized flag
+uint8_t os_running; // Kernel Running flag
+
+// Kernel Control Service Calls declarations
+SVC_0_1(svcKernelInitialize, osStatus, RET_osStatus)
+SVC_0_1(svcKernelStart, osStatus, RET_osStatus)
+SVC_0_1(svcKernelRunning, int32_t, RET_int32_t)
+
+extern void sysThreadError (osStatus status);
+osThreadId svcThreadCreate (osThreadDef_t *thread_def, void *argument);
+osMessageQId svcMessageCreate (osMessageQDef_t *queue_def, osThreadId thread_id);
+
+// Kernel Control Service Calls
+
+/// Initialize the RTOS Kernel for creating objects
+osStatus svcKernelInitialize (void) {
+ if (os_initialized) return osOK;
+
+ rt_sys_init(); // RTX System Initialization
+ os_tsk.run->prio = 255; // Highest priority
+
+ sysThreadError(osOK);
+
+ os_initialized = 1;
+
+ return osOK;
+}
+
+/// Start the RTOS Kernel
+osStatus svcKernelStart (void) {
+
+ if (os_running) return osOK;
+
+ // Create OS Timers resources (Message Queue & Thread)
+ osMessageQId_osTimerMessageQ = svcMessageCreate (&os_messageQ_def_osTimerMessageQ, NULL);
+ osThreadId_osTimerThread = svcThreadCreate(&os_thread_def_osTimerThread, NULL);
+
+ rt_tsk_prio(0, 0); // Lowest priority
+ __set_PSP(os_tsk.run->tsk_stack + 8*4); // New context
+ os_tsk.run = NULL; // Force context switch
+
+ rt_sys_start();
+
+ os_running = 1;
+
+ return osOK;
+}
+
+/// Check if the RTOS kernel is already started
+int32_t svcKernelRunning(void) {
+ return os_running;
+}
+
+// Kernel Control Public API
+
+/// Initialize the RTOS Kernel for creating objects
+osStatus osKernelInitialize (void) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ if ((__get_CONTROL() & 1) == 0) { // Privileged mode
+ return svcKernelInitialize();
+ } else {
+ return __svcKernelInitialize();
+ }
+}
+
+/// Start the RTOS Kernel
+osStatus osKernelStart (void) {
+ uint32_t stack[8];
+
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ switch (__get_CONTROL() & 0x03) {
+ case 0x00: // Privileged Thread mode & MSP
+ __set_PSP((uint32_t)(stack + 8)); // Initial PSP
+ if (os_flags & 1) {
+ __set_CONTROL(0x02); // Set Privileged Thread mode & PSP
+ } else {
+ __set_CONTROL(0x03); // Set Unprivileged Thread mode & PSP
+ }
+ __DSB();
+ __ISB();
+ break;
+ case 0x01: // Unprivileged Thread mode & MSP
+ return osErrorOS;
+ case 0x02: // Privileged Thread mode & PSP
+ if ((os_flags & 1) == 0) { // Unprivileged Thread mode requested
+ __set_CONTROL(0x03); // Set Unprivileged Thread mode & PSP
+ __DSB();
+ __ISB();
+ }
+ break;
+ case 0x03: // Unprivileged Thread mode & PSP
+ if (os_flags & 1) return osErrorOS; // Privileged Thread mode requested
+ break;
+ }
+ return __svcKernelStart();
+}
+
+/// Check if the RTOS kernel is already started
+int32_t osKernelRunning(void) {
+ if ((__get_IPSR() != 0) || ((__get_CONTROL() & 1) == 0)) {
+ // in ISR or Privileged
+ return os_running;
+ } else {
+ return __svcKernelRunning();
+ }
+}
+
+
+// ==== Thread Management ====
+
+__NO_RETURN void osThreadExit (void);
+
+// Thread Service Calls declarations
+SVC_2_1(svcThreadCreate, osThreadId, osThreadDef_t *, void *, RET_pointer)
+SVC_0_1(svcThreadGetId, osThreadId, RET_pointer)
+SVC_1_1(svcThreadTerminate, osStatus, osThreadId, RET_osStatus)
+SVC_0_1(svcThreadYield, osStatus, RET_osStatus)
+SVC_2_1(svcThreadSetPriority, osStatus, osThreadId, osPriority, RET_osStatus)
+SVC_1_1(svcThreadGetPriority, osPriority, osThreadId, RET_osPriority)
+
+// Thread Service Calls
+extern OS_TID rt_get_TID (void);
+extern void rt_init_context (P_TCB p_TCB, U8 priority, FUNCP task_body);
+
+/// Create a thread and add it to Active Threads and set it to state READY
+osThreadId svcThreadCreate (osThreadDef_t *thread_def, void *argument) {
+ P_TCB ptcb;
+
+ if ((thread_def == NULL) ||
+ (thread_def->pthread == NULL) ||
+ (thread_def->tpriority <= osPriorityIdle) ||
+ (thread_def->tpriority > osPriorityRealtime) ||
+ (thread_def->stacksize == 0) ||
+ (thread_def->stack_pointer == NULL) ) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ U8 priority = thread_def->tpriority - osPriorityIdle + 1;
+ P_TCB task_context = &thread_def->tcb;
+
+ /* If "size != 0" use a private user provided stack. */
+ task_context->stack = (U32*)thread_def->stack_pointer;
+ task_context->priv_stack = thread_def->stacksize;
+ /* Pass parameter 'argv' to 'rt_init_context' */
+ task_context->msg = argument;
+ /* For 'size == 0' system allocates the user stack from the memory pool. */
+ rt_init_context (task_context, priority, (FUNCP)thread_def->pthread);
+
+ /* Find a free entry in 'os_active_TCB' table. */
+ OS_TID tsk = rt_get_TID ();
+ os_active_TCB[tsk-1] = task_context;
+ task_context->task_id = tsk;
+ DBG_TASK_NOTIFY(task_context, __TRUE);
+ rt_dispatch (task_context);
+
+ ptcb = (P_TCB)os_active_TCB[tsk - 1]; // TCB pointer
+
+ *((uint32_t *)ptcb->tsk_stack + 13) = (uint32_t)osThreadExit;
+
+ return ptcb;
+}
+
+/// Return the thread ID of the current running thread
+osThreadId svcThreadGetId (void) {
+ OS_TID tsk;
+
+ tsk = rt_tsk_self();
+ if (tsk == 0) return NULL;
+ return (P_TCB)os_active_TCB[tsk - 1];
+}
+
+/// Terminate execution of a thread and remove it from ActiveThreads
+osStatus svcThreadTerminate (osThreadId thread_id) {
+ OS_RESULT res;
+ P_TCB ptcb;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return osErrorParameter;
+
+ res = rt_tsk_delete(ptcb->task_id); // Delete task
+
+ if (res == OS_R_NOK) return osErrorResource; // Delete task failed
+
+ return osOK;
+}
+
+/// Pass control to next thread that is in state READY
+osStatus svcThreadYield (void) {
+ rt_tsk_pass(); // Pass control to next task
+ return osOK;
+}
+
+/// Change prority of an active thread
+osStatus svcThreadSetPriority (osThreadId thread_id, osPriority priority) {
+ OS_RESULT res;
+ P_TCB ptcb;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return osErrorParameter;
+
+ if ((priority < osPriorityIdle) || (priority > osPriorityRealtime)) {
+ return osErrorValue;
+ }
+
+ res = rt_tsk_prio( // Change task priority
+ ptcb->task_id, // Task ID
+ priority - osPriorityIdle + 1 // New task priority
+ );
+
+ if (res == OS_R_NOK) return osErrorResource; // Change task priority failed
+
+ return osOK;
+}
+
+/// Get current prority of an active thread
+osPriority svcThreadGetPriority (osThreadId thread_id) {
+ P_TCB ptcb;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return osPriorityError;
+
+ return (osPriority)(ptcb->prio - 1 + osPriorityIdle);
+}
+
+
+// Thread Public API
+
+/// Create a thread and add it to Active Threads and set it to state READY
+osThreadId osThreadCreate (osThreadDef_t *thread_def, void *argument) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcThreadCreate(thread_def, argument);
+ } else {
+ return __svcThreadCreate(thread_def, argument);
+ }
+}
+
+/// Return the thread ID of the current running thread
+osThreadId osThreadGetId (void) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ return __svcThreadGetId();
+}
+
+/// Terminate execution of a thread and remove it from ActiveThreads
+osStatus osThreadTerminate (osThreadId thread_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcThreadTerminate(thread_id);
+}
+
+/// Pass control to next thread that is in state READY
+osStatus osThreadYield (void) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcThreadYield();
+}
+
+/// Change prority of an active thread
+osStatus osThreadSetPriority (osThreadId thread_id, osPriority priority) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcThreadSetPriority(thread_id, priority);
+}
+
+/// Get current prority of an active thread
+osPriority osThreadGetPriority (osThreadId thread_id) {
+ if (__get_IPSR() != 0) return osPriorityError;// Not allowed in ISR
+ return __svcThreadGetPriority(thread_id);
+}
+
+/// INTERNAL - Not Public
+/// Auto Terminate Thread on exit (used implicitly when thread exists)
+__NO_RETURN void osThreadExit (void) {
+ __svcThreadTerminate(__svcThreadGetId());
+ for (;;); // Should never come here
+}
+
+
+// ==== Generic Wait Functions ====
+
+// Generic Wait Service Calls declarations
+SVC_1_1(svcDelay, osStatus, uint32_t, RET_osStatus)
+#if osFeature_Wait != 0
+SVC_1_3(svcWait, os_InRegs osEvent, uint32_t, RET_osEvent)
+#endif
+
+// Generic Wait Service Calls
+
+/// Wait for Timeout (Time Delay)
+osStatus svcDelay (uint32_t millisec) {
+ if (millisec == 0) return osOK;
+ rt_dly_wait(rt_ms2tick(millisec));
+ return osEventTimeout;
+}
+
+/// Wait for Signal, Message, Mail, or Timeout
+#if osFeature_Wait != 0
+os_InRegs osEvent_type svcWait (uint32_t millisec) {
+ osEvent ret;
+
+ if (millisec == 0) {
+ ret.status = osOK;
+ return osEvent_ret_status;
+ }
+
+ /* To Do: osEventSignal, osEventMessage, osEventMail */
+ rt_dly_wait(rt_ms2tick(millisec));
+ ret.status = osEventTimeout;
+
+ return osEvent_ret_status;
+}
+#endif
+
+
+// Generic Wait API
+
+/// Wait for Timeout (Time Delay)
+osStatus osDelay (uint32_t millisec) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcDelay(millisec);
+}
+
+/// Wait for Signal, Message, Mail, or Timeout
+os_InRegs osEvent osWait (uint32_t millisec) {
+ osEvent ret;
+
+#if osFeature_Wait == 0
+ ret.status = osErrorOS;
+ return ret;
+#else
+ if (__get_IPSR() != 0) { // Not allowed in ISR
+ ret.status = osErrorISR;
+ return ret;
+ }
+ return __svcWait(millisec);
+#endif
+}
+
+
+// ==== Timer Management ====
+
+// Timer definitions
+#define osTimerInvalid 0
+#define osTimerStopped 1
+#define osTimerRunning 2
+
+// Timer structures
+
+typedef struct os_timer_cb_ { // Timer Control Block
+ struct os_timer_cb_ *next; // Pointer to next active Timer
+ uint8_t state; // Timer State
+ uint8_t type; // Timer Type (Periodic/One-shot)
+ uint16_t reserved; // Reserved
+ uint16_t tcnt; // Timer Delay Count
+ uint16_t icnt; // Timer Initial Count
+ void *arg; // Timer Function Argument
+ osTimerDef_t *timer; // Pointer to Timer definition
+} os_timer_cb;
+
+// Timer variables
+os_timer_cb *os_timer_head; // Pointer to first active Timer
+
+
+// Timer Helper Functions
+
+// Insert Timer into the list sorted by time
+static void rt_timer_insert (os_timer_cb *pt, uint32_t tcnt) {
+ os_timer_cb *p, *prev;
+
+ prev = NULL;
+ p = os_timer_head;
+ while (p != NULL) {
+ if (tcnt < p->tcnt) break;
+ tcnt -= p->tcnt;
+ prev = p;
+ p = p->next;
+ }
+ pt->next = p;
+ pt->tcnt = (uint16_t)tcnt;
+ if (p != NULL) {
+ p->tcnt -= pt->tcnt;
+ }
+ if (prev != NULL) {
+ prev->next = pt;
+ } else {
+ os_timer_head = pt;
+ }
+}
+
+// Remove Timer from the list
+static int rt_timer_remove (os_timer_cb *pt) {
+ os_timer_cb *p, *prev;
+
+ prev = NULL;
+ p = os_timer_head;
+ while (p != NULL) {
+ if (p == pt) break;
+ prev = p;
+ p = p->next;
+ }
+ if (p == NULL) return -1;
+ if (prev != NULL) {
+ prev->next = pt->next;
+ } else {
+ os_timer_head = pt->next;
+ }
+ if (pt->next != NULL) {
+ pt->next->tcnt += pt->tcnt;
+ }
+
+ return 0;
+}
+
+
+// Timer Service Calls declarations
+SVC_3_1(svcTimerCreate, osTimerId, osTimerDef_t *, os_timer_type, void *, RET_pointer)
+SVC_2_1(svcTimerStart, osStatus, osTimerId, uint32_t, RET_osStatus)
+SVC_1_1(svcTimerStop, osStatus, osTimerId, RET_osStatus)
+SVC_1_1(svcTimerDelete, osStatus, osTimerId, RET_osStatus)
+SVC_1_2(svcTimerCall, os_InRegs osCallback, osTimerId, RET_osCallback)
+
+// Timer Management Service Calls
+
+/// Create timer
+osTimerId svcTimerCreate (osTimerDef_t *timer_def, os_timer_type type, void *argument) {
+ os_timer_cb *pt;
+
+ if ((timer_def == NULL) || (timer_def->ptimer == NULL)) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ pt = timer_def->timer;
+ if (pt == NULL) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ if ((type != osTimerOnce) && (type != osTimerPeriodic)) {
+ sysThreadError(osErrorValue);
+ return NULL;
+ }
+
+ if (osThreadId_osTimerThread == NULL) {
+ sysThreadError(osErrorResource);
+ return NULL;
+ }
+
+ if (pt->state != osTimerInvalid){
+ sysThreadError(osErrorResource);
+ return NULL;
+ }
+
+ pt->state = osTimerStopped;
+ pt->type = (uint8_t)type;
+ pt->arg = argument;
+ pt->timer = timer_def;
+
+ return (osTimerId)pt;
+}
+
+/// Start or restart timer
+osStatus svcTimerStart (osTimerId timer_id, uint32_t millisec) {
+ os_timer_cb *pt;
+ uint32_t tcnt;
+
+ pt = rt_id2obj(timer_id);
+ if (pt == NULL) return osErrorParameter;
+
+ tcnt = rt_ms2tick(millisec);
+ if (tcnt == 0) return osErrorValue;
+
+ switch (pt->state) {
+ case osTimerRunning:
+ if (rt_timer_remove(pt) != 0) {
+ return osErrorResource;
+ }
+ break;
+ case osTimerStopped:
+ pt->state = osTimerRunning;
+ pt->icnt = (uint16_t)tcnt;
+ break;
+ default:
+ return osErrorResource;
+ }
+
+ rt_timer_insert(pt, tcnt);
+
+ return osOK;
+}
+
+/// Stop timer
+osStatus svcTimerStop (osTimerId timer_id) {
+ os_timer_cb *pt;
+
+ pt = rt_id2obj(timer_id);
+ if (pt == NULL) return osErrorParameter;
+
+ if (pt->state != osTimerRunning) return osErrorResource;
+
+ pt->state = osTimerStopped;
+
+ if (rt_timer_remove(pt) != 0) {
+ return osErrorResource;
+ }
+
+ return osOK;
+}
+
+/// Delete timer
+osStatus svcTimerDelete (osTimerId timer_id) {
+ os_timer_cb *pt;
+
+ pt = rt_id2obj(timer_id);
+ if (pt == NULL) return osErrorParameter;
+
+ switch (pt->state) {
+ case osTimerRunning:
+ rt_timer_remove(pt);
+ break;
+ case osTimerStopped:
+ break;
+ default:
+ return osErrorResource;
+ }
+
+ pt->state = osTimerInvalid;
+
+ return osOK;
+}
+
+/// Get timer callback parameters
+os_InRegs osCallback_type svcTimerCall (osTimerId timer_id) {
+ os_timer_cb *pt;
+ osCallback ret;
+
+ pt = rt_id2obj(timer_id);
+ if (pt == NULL) {
+ ret.fp = NULL;
+ ret.arg = NULL;
+ return osCallback_ret;
+ }
+
+ ret.fp = (void *)pt->timer->ptimer;
+ ret.arg = pt->arg;
+
+ return osCallback_ret;
+}
+
+static __INLINE osStatus isrMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec);
+
+/// Timer Tick (called each SysTick)
+void sysTimerTick (void) {
+ os_timer_cb *pt, *p;
+
+ p = os_timer_head;
+ if (p == NULL) return;
+
+ p->tcnt--;
+ while ((p != NULL) && (p->tcnt == 0)) {
+ pt = p;
+ p = p->next;
+ os_timer_head = p;
+ isrMessagePut(osMessageQId_osTimerMessageQ, (uint32_t)pt, 0);
+ if (pt->type == osTimerPeriodic) {
+ rt_timer_insert(pt, pt->icnt);
+ } else {
+ pt->state = osTimerStopped;
+ }
+ }
+}
+
+
+// Timer Management Public API
+
+/// Create timer
+osTimerId osTimerCreate (osTimerDef_t *timer_def, os_timer_type type, void *argument) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcTimerCreate(timer_def, type, argument);
+ } else {
+ return __svcTimerCreate(timer_def, type, argument);
+ }
+}
+
+/// Start or restart timer
+osStatus osTimerStart (osTimerId timer_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcTimerStart(timer_id, millisec);
+}
+
+/// Stop timer
+osStatus osTimerStop (osTimerId timer_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcTimerStop(timer_id);
+}
+
+/// Delete timer
+osStatus osTimerDelete (osTimerId timer_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcTimerDelete(timer_id);
+}
+
+/// INTERNAL - Not Public
+/// Get timer callback parameters (used by OS Timer Thread)
+os_InRegs osCallback osTimerCall (osTimerId timer_id) {
+ return __svcTimerCall(timer_id);
+}
+
+
+// Timer Thread
+__NO_RETURN void osTimerThread (void const *argument) {
+ osCallback cb;
+ osEvent evt;
+
+ for (;;) {
+ evt = osMessageGet(osMessageQId_osTimerMessageQ, osWaitForever);
+ if (evt.status == osEventMessage) {
+ cb = osTimerCall(evt.value.p);
+ if (cb.fp != NULL) {
+ (*(os_ptimer)cb.fp)(cb.arg);
+ }
+ }
+ }
+}
+
+
+// ==== Signal Management ====
+
+// Signal Service Calls declarations
+SVC_2_1(svcSignalSet, int32_t, osThreadId, int32_t, RET_int32_t)
+SVC_2_1(svcSignalClear, int32_t, osThreadId, int32_t, RET_int32_t)
+SVC_1_1(svcSignalGet, int32_t, osThreadId, RET_int32_t)
+SVC_2_3(svcSignalWait, os_InRegs osEvent, int32_t, uint32_t, RET_osEvent)
+
+// Signal Service Calls
+
+/// Set the specified Signal Flags of an active thread
+int32_t svcSignalSet (osThreadId thread_id, int32_t signal) {
+ P_TCB ptcb;
+ int32_t sig;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return 0x80000000;
+
+ if (signal & (0xFFFFFFFF << osFeature_Signals)) return 0x80000000;
+
+ sig = ptcb->events; // Previous signal flags
+
+ rt_evt_set(signal, ptcb->task_id); // Set event flags
+
+ return sig;
+}
+
+/// Clear the specified Signal Flags of an active thread
+int32_t svcSignalClear (osThreadId thread_id, int32_t signal) {
+ P_TCB ptcb;
+ int32_t sig;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return 0x80000000;
+
+ if (signal & (0xFFFFFFFF << osFeature_Signals)) return 0x80000000;
+
+ sig = ptcb->events; // Previous signal flags
+
+ rt_evt_clr(signal, ptcb->task_id); // Clear event flags
+
+ return sig;
+}
+
+/// Get Signal Flags status of an active thread
+int32_t svcSignalGet (osThreadId thread_id) {
+ P_TCB ptcb;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return 0x80000000;
+
+ return ptcb->events; // Return event flags
+}
+
+/// Wait for one or more Signal Flags to become signaled for the current RUNNING thread
+os_InRegs osEvent_type svcSignalWait (int32_t signals, uint32_t millisec) {
+ OS_RESULT res;
+ osEvent ret;
+
+ if (signals & (0xFFFFFFFF << osFeature_Signals)) {
+ ret.status = osErrorValue;
+ return osEvent_ret_status;
+ }
+
+ if (signals != 0) { // Wait for all specified signals
+ res = rt_evt_wait(signals, rt_ms2tick(millisec), __TRUE);
+ } else { // Wait for any signal
+ res = rt_evt_wait(0xFFFF, rt_ms2tick(millisec), __FALSE);
+ }
+
+ if (res == OS_R_EVT) {
+ ret.status = osEventSignal;
+ ret.value.signals = signals ? signals : os_tsk.run->waits;
+ } else {
+ ret.status = millisec ? osEventTimeout : osOK;
+ ret.value.signals = 0;
+ }
+
+ return osEvent_ret_value;
+}
+
+
+// Signal ISR Calls
+
+/// Set the specified Signal Flags of an active thread
+static __INLINE int32_t isrSignalSet (osThreadId thread_id, int32_t signal) {
+ P_TCB ptcb;
+ int32_t sig;
+
+ ptcb = rt_tid2ptcb(thread_id); // Get TCB pointer
+ if (ptcb == NULL) return 0x80000000;
+
+ if (signal & (0xFFFFFFFF << osFeature_Signals)) return 0x80000000;
+
+ sig = ptcb->events; // Previous signal flags
+
+ isr_evt_set(signal, ptcb->task_id); // Set event flags
+
+ return sig;
+}
+
+
+// Signal Public API
+
+/// Set the specified Signal Flags of an active thread
+int32_t osSignalSet (osThreadId thread_id, int32_t signal) {
+ if (__get_IPSR() != 0) { // in ISR
+ return isrSignalSet(thread_id, signal);
+ } else { // in Thread
+ return __svcSignalSet(thread_id, signal);
+ }
+}
+
+/// Clear the specified Signal Flags of an active thread
+int32_t osSignalClear (osThreadId thread_id, int32_t signal) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcSignalClear(thread_id, signal);
+}
+
+/// Get Signal Flags status of an active thread
+int32_t osSignalGet (osThreadId thread_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcSignalGet(thread_id);
+}
+
+/// Wait for one or more Signal Flags to become signaled for the current RUNNING thread
+os_InRegs osEvent osSignalWait (int32_t signals, uint32_t millisec) {
+ osEvent ret;
+
+ if (__get_IPSR() != 0) { // Not allowed in ISR
+ ret.status = osErrorISR;
+ return ret;
+ }
+ return __svcSignalWait(signals, millisec);
+}
+
+
+// ==== Mutex Management ====
+
+// Mutex Service Calls declarations
+SVC_1_1(svcMutexCreate, osMutexId, osMutexDef_t *, RET_pointer)
+SVC_2_1(svcMutexWait, osStatus, osMutexId, uint32_t, RET_osStatus)
+SVC_1_1(svcMutexRelease, osStatus, osMutexId, RET_osStatus)
+SVC_1_1(svcMutexDelete, osStatus, osMutexId, RET_osStatus)
+
+// Mutex Service Calls
+
+/// Create and Initialize a Mutex object
+osMutexId svcMutexCreate (osMutexDef_t *mutex_def) {
+ OS_ID mut;
+
+ if (mutex_def == NULL) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ mut = mutex_def->mutex;
+ if (mut == NULL) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ if (((P_MUCB)mut)->cb_type != 0) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ rt_mut_init(mut); // Initialize Mutex
+
+ return mut;
+}
+
+/// Wait until a Mutex becomes available
+osStatus svcMutexWait (osMutexId mutex_id, uint32_t millisec) {
+ OS_ID mut;
+ OS_RESULT res;
+
+ mut = rt_id2obj(mutex_id);
+ if (mut == NULL) return osErrorParameter;
+
+ if (((P_MUCB)mut)->cb_type != MUCB) return osErrorParameter;
+
+ res = rt_mut_wait(mut, rt_ms2tick(millisec)); // Wait for Mutex
+
+ if (res == OS_R_TMO) {
+ return (millisec ? osErrorTimeoutResource : osErrorResource);
+ }
+
+ return osOK;
+}
+
+/// Release a Mutex that was obtained with osMutexWait
+osStatus svcMutexRelease (osMutexId mutex_id) {
+ OS_ID mut;
+ OS_RESULT res;
+
+ mut = rt_id2obj(mutex_id);
+ if (mut == NULL) return osErrorParameter;
+
+ if (((P_MUCB)mut)->cb_type != MUCB) return osErrorParameter;
+
+ res = rt_mut_release(mut); // Release Mutex
+
+ if (res == OS_R_NOK) return osErrorResource; // Thread not owner or Zero Counter
+
+ return osOK;
+}
+
+/// Delete a Mutex that was created by osMutexCreate
+osStatus svcMutexDelete (osMutexId mutex_id) {
+ OS_ID mut;
+
+ mut = rt_id2obj(mutex_id);
+ if (mut == NULL) return osErrorParameter;
+
+ if (((P_MUCB)mut)->cb_type != MUCB) return osErrorParameter;
+
+ rt_mut_delete(mut); // Release Mutex
+
+ return osOK;
+}
+
+
+// Mutex Public API
+
+/// Create and Initialize a Mutex object
+osMutexId osMutexCreate (osMutexDef_t *mutex_def) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcMutexCreate(mutex_def);
+ } else {
+ return __svcMutexCreate(mutex_def);
+ }
+}
+
+/// Wait until a Mutex becomes available
+osStatus osMutexWait (osMutexId mutex_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcMutexWait(mutex_id, millisec);
+}
+
+/// Release a Mutex that was obtained with osMutexWait
+osStatus osMutexRelease (osMutexId mutex_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcMutexRelease(mutex_id);
+}
+
+/// Delete a Mutex that was created by osMutexCreate
+osStatus osMutexDelete (osMutexId mutex_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcMutexDelete(mutex_id);
+}
+
+
+// ==== Semaphore Management ====
+
+// Semaphore Service Calls declarations
+SVC_2_1(svcSemaphoreCreate, osSemaphoreId, const osSemaphoreDef_t *, int32_t, RET_pointer)
+SVC_2_1(svcSemaphoreWait, int32_t, osSemaphoreId, uint32_t, RET_int32_t)
+SVC_1_1(svcSemaphoreRelease, osStatus, osSemaphoreId, RET_osStatus)
+SVC_1_1(svcSemaphoreDelete, osStatus, osSemaphoreId, RET_osStatus)
+
+// Semaphore Service Calls
+
+/// Create and Initialize a Semaphore object
+osSemaphoreId svcSemaphoreCreate (const osSemaphoreDef_t *semaphore_def, int32_t count) {
+ OS_ID sem;
+
+ if (semaphore_def == NULL) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ sem = semaphore_def->semaphore;
+ if (sem == NULL) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ if (((P_SCB)sem)->cb_type != 0) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ if (count > osFeature_Semaphore) {
+ sysThreadError(osErrorValue);
+ return NULL;
+ }
+
+ rt_sem_init(sem, count); // Initialize Semaphore
+
+ return sem;
+}
+
+/// Wait until a Semaphore becomes available
+int32_t svcSemaphoreWait (osSemaphoreId semaphore_id, uint32_t millisec) {
+ OS_ID sem;
+ OS_RESULT res;
+
+ sem = rt_id2obj(semaphore_id);
+ if (sem == NULL) return -1;
+
+ if (((P_SCB)sem)->cb_type != SCB) return -1;
+
+ res = rt_sem_wait(sem, rt_ms2tick(millisec)); // Wait for Semaphore
+
+ if (res == OS_R_TMO) return 0; // Timeout
+
+ return (((P_SCB)sem)->tokens + 1);
+}
+
+/// Release a Semaphore
+osStatus svcSemaphoreRelease (osSemaphoreId semaphore_id) {
+ OS_ID sem;
+
+ sem = rt_id2obj(semaphore_id);
+ if (sem == NULL) return osErrorParameter;
+
+ if (((P_SCB)sem)->cb_type != SCB) return osErrorParameter;
+
+ rt_sem_send(sem); // Release Semaphore
+
+ return osOK;
+}
+
+/// Delete a Semaphore that was created by osSemaphoreCreate
+osStatus svcSemaphoreDelete (osSemaphoreId semaphore_id) {
+ OS_ID sem;
+
+ sem = rt_id2obj(semaphore_id);
+ if (sem == NULL) return osErrorParameter;
+
+ if (((P_SCB)sem)->cb_type != SCB) return osErrorParameter;
+
+ rt_sem_delete(sem); // Delete Semaphore
+
+ return osOK;
+}
+
+
+// Semaphore ISR Calls
+
+/// Release a Semaphore
+static __INLINE osStatus isrSemaphoreRelease (osSemaphoreId semaphore_id) {
+ OS_ID sem;
+
+ sem = rt_id2obj(semaphore_id);
+ if (sem == NULL) return osErrorParameter;
+
+ if (((P_SCB)sem)->cb_type != SCB) return osErrorParameter;
+
+ isr_sem_send(sem); // Release Semaphore
+
+ return osOK;
+}
+
+
+// Semaphore Public API
+
+/// Create and Initialize a Semaphore object
+osSemaphoreId osSemaphoreCreate (osSemaphoreDef_t *semaphore_def, int32_t count) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcSemaphoreCreate(semaphore_def, count);
+ } else {
+ return __svcSemaphoreCreate(semaphore_def, count);
+ }
+}
+
+/// Wait until a Semaphore becomes available
+int32_t osSemaphoreWait (osSemaphoreId semaphore_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) return -1; // Not allowed in ISR
+ return __svcSemaphoreWait(semaphore_id, millisec);
+}
+
+/// Release a Semaphore
+osStatus osSemaphoreRelease (osSemaphoreId semaphore_id) {
+ if (__get_IPSR() != 0) { // in ISR
+ return isrSemaphoreRelease(semaphore_id);
+ } else { // in Thread
+ return __svcSemaphoreRelease(semaphore_id);
+ }
+}
+
+/// Delete a Semaphore that was created by osSemaphoreCreate
+osStatus osSemaphoreDelete (osSemaphoreId semaphore_id) {
+ if (__get_IPSR() != 0) return osErrorISR; // Not allowed in ISR
+ return __svcSemaphoreDelete(semaphore_id);
+}
+
+
+// ==== Memory Management Functions ====
+
+// Memory Management Helper Functions
+
+// Clear Memory Box (Zero init)
+static void rt_clr_box (void *box_mem, void *box) {
+ uint32_t *p, n;
+
+ if (box) {
+ p = box;
+ for (n = ((P_BM)box_mem)->blk_size; n; n -= 4) {
+ *p++ = 0;
+ }
+ }
+}
+
+// Memory Management Service Calls declarations
+SVC_1_1(svcPoolCreate, osPoolId, const osPoolDef_t *, RET_pointer)
+SVC_2_1(sysPoolAlloc, void *, osPoolId, uint32_t, RET_pointer)
+SVC_2_1(sysPoolFree, osStatus, osPoolId, void *, RET_osStatus)
+
+// Memory Management Service & ISR Calls
+
+/// Create and Initialize memory pool
+osPoolId svcPoolCreate (const osPoolDef_t *pool_def) {
+ uint32_t blk_sz;
+
+ if ((pool_def == NULL) ||
+ (pool_def->pool_sz == 0) ||
+ (pool_def->item_sz == 0) ||
+ (pool_def->pool == NULL)) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ blk_sz = (pool_def->item_sz + 3) & ~3;
+
+ _init_box(pool_def->pool, sizeof(struct OS_BM) + pool_def->pool_sz * blk_sz, blk_sz);
+
+ return pool_def->pool;
+}
+
+/// Allocate a memory block from a memory pool
+void *sysPoolAlloc (osPoolId pool_id, uint32_t clr) {
+ void *ptr;
+
+ if (pool_id == NULL) return NULL;
+
+ ptr = rt_alloc_box(pool_id);
+ if (clr) {
+ rt_clr_box(pool_id, ptr);
+ }
+
+ return ptr;
+}
+
+/// Return an allocated memory block back to a specific memory pool
+osStatus sysPoolFree (osPoolId pool_id, void *block) {
+ int32_t res;
+
+ if (pool_id == NULL) return osErrorParameter;
+
+ res = rt_free_box(pool_id, block);
+ if (res != 0) return osErrorValue;
+
+ return osOK;
+}
+
+
+// Memory Management Public API
+
+/// Create and Initialize memory pool
+osPoolId osPoolCreate (osPoolDef_t *pool_def) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcPoolCreate(pool_def);
+ } else {
+ return __svcPoolCreate(pool_def);
+ }
+}
+
+/// Allocate a memory block from a memory pool
+void *osPoolAlloc (osPoolId pool_id) {
+ if ((__get_IPSR() != 0) || ((__get_CONTROL() & 1) == 0)) { // in ISR or Privileged
+ return sysPoolAlloc(pool_id, 0);
+ } else { // in Thread
+ return __sysPoolAlloc(pool_id, 0);
+ }
+}
+
+/// Allocate a memory block from a memory pool and set memory block to zero
+void *osPoolCAlloc (osPoolId pool_id) {
+ if ((__get_IPSR() != 0) || ((__get_CONTROL() & 1) == 0)) { // in ISR or Privileged
+ return sysPoolAlloc(pool_id, 1);
+ } else { // in Thread
+ return __sysPoolAlloc(pool_id, 1);
+ }
+}
+
+/// Return an allocated memory block back to a specific memory pool
+osStatus osPoolFree (osPoolId pool_id, void *block) {
+ if ((__get_IPSR() != 0) || ((__get_CONTROL() & 1) == 0)) { // in ISR or Privileged
+ return sysPoolFree(pool_id, block);
+ } else { // in Thread
+ return __sysPoolFree(pool_id, block);
+ }
+}
+
+
+// ==== Message Queue Management Functions ====
+
+// Message Queue Management Service Calls declarations
+SVC_2_1(svcMessageCreate, osMessageQId, osMessageQDef_t *, osThreadId, RET_pointer)
+SVC_3_1(svcMessagePut, osStatus, osMessageQId, uint32_t, uint32_t, RET_osStatus)
+SVC_2_3(svcMessageGet, os_InRegs osEvent, osMessageQId, uint32_t, RET_osEvent)
+
+// Message Queue Service Calls
+
+/// Create and Initialize Message Queue
+osMessageQId svcMessageCreate (osMessageQDef_t *queue_def, osThreadId thread_id) {
+
+ if ((queue_def == NULL) ||
+ (queue_def->queue_sz == 0) ||
+ (queue_def->pool == NULL)) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ if (((P_MCB)queue_def->pool)->cb_type != 0) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ rt_mbx_init(queue_def->pool, 4*(queue_def->queue_sz + 4));
+
+ return queue_def->pool;
+}
+
+/// Put a Message to a Queue
+osStatus svcMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec) {
+ OS_RESULT res;
+
+ if (queue_id == NULL) return osErrorParameter;
+
+ if (((P_MCB)queue_id)->cb_type != MCB) return osErrorParameter;
+
+ res = rt_mbx_send(queue_id, (void *)info, rt_ms2tick(millisec));
+
+ if (res == OS_R_TMO) {
+ return (millisec ? osErrorTimeoutResource : osErrorResource);
+ }
+
+ return osOK;
+}
+
+/// Get a Message or Wait for a Message from a Queue
+os_InRegs osEvent_type svcMessageGet (osMessageQId queue_id, uint32_t millisec) {
+ OS_RESULT res;
+ osEvent ret;
+
+ if (queue_id == NULL) {
+ ret.status = osErrorParameter;
+ return osEvent_ret_status;
+ }
+
+ if (((P_MCB)queue_id)->cb_type != MCB) {
+ ret.status = osErrorParameter;
+ return osEvent_ret_status;
+ }
+
+ res = rt_mbx_wait(queue_id, &ret.value.p, rt_ms2tick(millisec));
+
+ if (res == OS_R_TMO) {
+ ret.status = millisec ? osEventTimeout : osOK;
+ return osEvent_ret_value;
+ }
+
+ ret.status = osEventMessage;
+
+ return osEvent_ret_value;
+}
+
+
+// Message Queue ISR Calls
+
+/// Put a Message to a Queue
+static __INLINE osStatus isrMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec) {
+
+ if ((queue_id == NULL) || (millisec != 0)) {
+ return osErrorParameter;
+ }
+
+ if (((P_MCB)queue_id)->cb_type != MCB) return osErrorParameter;
+
+ if (rt_mbx_check(queue_id) == 0) { // Check if Queue is full
+ return osErrorResource;
+ }
+
+ isr_mbx_send(queue_id, (void *)info);
+
+ return osOK;
+}
+
+/// Get a Message or Wait for a Message from a Queue
+static __INLINE os_InRegs osEvent isrMessageGet (osMessageQId queue_id, uint32_t millisec) {
+ OS_RESULT res;
+ osEvent ret;
+
+ if ((queue_id == NULL) || (millisec != 0)) {
+ ret.status = osErrorParameter;
+ return ret;
+ }
+
+ if (((P_MCB)queue_id)->cb_type != MCB) {
+ ret.status = osErrorParameter;
+ return ret;
+ }
+
+ res = isr_mbx_receive(queue_id, &ret.value.p);
+
+ if (res != OS_R_MBX) {
+ ret.status = osOK;
+ return ret;
+ }
+
+ ret.status = osEventMessage;
+
+ return ret;
+}
+
+
+// Message Queue Management Public API
+
+/// Create and Initialize Message Queue
+osMessageQId osMessageCreate (osMessageQDef_t *queue_def, osThreadId thread_id) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcMessageCreate(queue_def, thread_id);
+ } else {
+ return __svcMessageCreate(queue_def, thread_id);
+ }
+}
+
+/// Put a Message to a Queue
+osStatus osMessagePut (osMessageQId queue_id, uint32_t info, uint32_t millisec) {
+ if (__get_IPSR() != 0) { // in ISR
+ return isrMessagePut(queue_id, info, millisec);
+ } else { // in Thread
+ return __svcMessagePut(queue_id, info, millisec);
+ }
+}
+
+/// Get a Message or Wait for a Message from a Queue
+os_InRegs osEvent osMessageGet (osMessageQId queue_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) { // in ISR
+ return isrMessageGet(queue_id, millisec);
+ } else { // in Thread
+ return __svcMessageGet(queue_id, millisec);
+ }
+}
+
+
+// ==== Mail Queue Management Functions ====
+
+// Mail Queue Management Service Calls declarations
+SVC_2_1(svcMailCreate, osMailQId, osMailQDef_t *, osThreadId, RET_pointer)
+SVC_4_1(sysMailAlloc, void *, osMailQId, uint32_t, uint32_t, uint32_t, RET_pointer)
+SVC_3_1(sysMailFree, osStatus, osMailQId, void *, uint32_t, RET_osStatus)
+
+// Mail Queue Management Service & ISR Calls
+
+/// Create and Initialize mail queue
+osMailQId svcMailCreate (osMailQDef_t *queue_def, osThreadId thread_id) {
+ uint32_t blk_sz;
+ P_MCB pmcb;
+ void *pool;
+
+ if ((queue_def == NULL) ||
+ (queue_def->queue_sz == 0) ||
+ (queue_def->item_sz == 0) ||
+ (queue_def->pool == NULL)) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ pmcb = *(((void **)queue_def->pool) + 0);
+ pool = *(((void **)queue_def->pool) + 1);
+
+ if ((pool == NULL) || (pmcb == NULL) || (pmcb->cb_type != 0)) {
+ sysThreadError(osErrorParameter);
+ return NULL;
+ }
+
+ blk_sz = (queue_def->item_sz + 3) & ~3;
+
+ _init_box(pool, sizeof(struct OS_BM) + queue_def->queue_sz * blk_sz, blk_sz);
+
+ rt_mbx_init(pmcb, 4*(queue_def->queue_sz + 4));
+
+
+ return queue_def->pool;
+}
+
+/// Allocate a memory block from a mail
+void *sysMailAlloc (osMailQId queue_id, uint32_t millisec, uint32_t isr, uint32_t clr) {
+ P_MCB pmcb;
+ void *pool;
+ void *mem;
+
+ if (queue_id == NULL) return NULL;
+
+ pmcb = *(((void **)queue_id) + 0);
+ pool = *(((void **)queue_id) + 1);
+
+ if ((pool == NULL) || (pmcb == NULL)) return NULL;
+
+ if (isr && (millisec != 0)) return NULL;
+
+ mem = rt_alloc_box(pool);
+ if (clr) {
+ rt_clr_box(pool, mem);
+ }
+
+ if ((mem == NULL) && (millisec != 0)) {
+ // Put Task to sleep when Memory not available
+ if (pmcb->p_lnk != NULL) {
+ rt_put_prio((P_XCB)pmcb, os_tsk.run);
+ } else {
+ pmcb->p_lnk = os_tsk.run;
+ os_tsk.run->p_lnk = NULL;
+ os_tsk.run->p_rlnk = (P_TCB)pmcb;
+ // Task is waiting to allocate a message
+ pmcb->state = 3;
+ }
+ rt_block(rt_ms2tick(millisec), WAIT_MBX);
+ }
+
+ return mem;
+}
+
+/// Free a memory block from a mail
+osStatus sysMailFree (osMailQId queue_id, void *mail, uint32_t isr) {
+ P_MCB pmcb;
+ P_TCB ptcb;
+ void *pool;
+ void *mem;
+ int32_t res;
+
+ if (queue_id == NULL) return osErrorParameter;
+
+ pmcb = *(((void **)queue_id) + 0);
+ pool = *(((void **)queue_id) + 1);
+
+ if ((pmcb == NULL) || (pool == NULL)) return osErrorParameter;
+
+ res = rt_free_box(pool, mail);
+
+ if (res != 0) return osErrorValue;
+
+ if (pmcb->state == 3) {
+ // Task is waiting to allocate a message
+ if (isr) {
+ rt_psq_enq (pmcb, (U32)pool);
+ rt_psh_req ();
+ } else {
+ mem = rt_alloc_box(pool);
+ if (mem != NULL) {
+ ptcb = rt_get_first((P_XCB)pmcb);
+ if (pmcb->p_lnk == NULL) {
+ pmcb->state = 0;
+ }
+ rt_ret_val(ptcb, (U32)mem);
+ rt_rmv_dly(ptcb);
+ rt_dispatch(ptcb);
+ }
+ }
+ }
+
+ return osOK;
+}
+
+
+// Mail Queue Management Public API
+
+/// Create and Initialize mail queue
+osMailQId osMailCreate (osMailQDef_t *queue_def, osThreadId thread_id) {
+ if (__get_IPSR() != 0) return NULL; // Not allowed in ISR
+ if (((__get_CONTROL() & 1) == 0) && (os_running == 0)) {
+ // Privileged and not running
+ return svcMailCreate(queue_def, thread_id);
+ } else {
+ return __svcMailCreate(queue_def, thread_id);
+ }
+}
+
+/// Allocate a memory block from a mail
+void *osMailAlloc (osMailQId queue_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) { // in ISR
+ return sysMailAlloc(queue_id, millisec, 1, 0);
+ } else { // in Thread
+ return __sysMailAlloc(queue_id, millisec, 0, 0);
+ }
+}
+
+/// Allocate a memory block from a mail and set memory block to zero
+void *osMailCAlloc (osMailQId queue_id, uint32_t millisec) {
+ if (__get_IPSR() != 0) { // in ISR
+ return sysMailAlloc(queue_id, millisec, 1, 1);
+ } else { // in Thread
+ return __sysMailAlloc(queue_id, millisec, 0, 1);
+ }
+}
+
+/// Free a memory block from a mail
+osStatus osMailFree (osMailQId queue_id, void *mail) {
+ if (__get_IPSR() != 0) { // in ISR
+ return sysMailFree(queue_id, mail, 1);
+ } else { // in Thread
+ return __sysMailFree(queue_id, mail, 0);
+ }
+}
+
+/// Put a mail to a queue
+osStatus osMailPut (osMailQId queue_id, void *mail) {
+ if (queue_id == NULL) return osErrorParameter;
+ return osMessagePut(*((void **)queue_id), (uint32_t)mail, 0);
+}
+
+/// Get a mail from a queue
+os_InRegs osEvent osMailGet (osMailQId queue_id, uint32_t millisec) {
+ osEvent ret;
+
+ if (queue_id == NULL) {
+ ret.status = osErrorParameter;
+ return ret;
+ }
+
+ ret = osMessageGet(*((void **)queue_id), millisec);
+ if (ret.status == osEventMessage) ret.status = osEventMail;
+
+ return ret;
+}
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Event.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,182 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_EVENT.C
+ * Purpose: Implements waits and wake-ups for event flags
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_Event.h"
+#include "rt_List.h"
+#include "rt_Task.h"
+#include "rt_HAL_CM.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_evt_wait -----------------------------------*/
+
+OS_RESULT rt_evt_wait (U16 wait_flags, U16 timeout, BOOL and_wait) {
+ /* Wait for one or more event flags with optional time-out. */
+ /* "wait_flags" identifies the flags to wait for. */
+ /* "timeout" is the time-out limit in system ticks (0xffff if no time-out) */
+ /* "and_wait" specifies the AND-ing of "wait_flags" as condition to be met */
+ /* to complete the wait. (OR-ing if set to 0). */
+ U32 block_state;
+
+ if (and_wait) {
+ /* Check for AND-connected events */
+ if ((os_tsk.run->events & wait_flags) == wait_flags) {
+ os_tsk.run->events &= ~wait_flags;
+ return (OS_R_EVT);
+ }
+ block_state = WAIT_AND;
+ }
+ else {
+ /* Check for OR-connected events */
+ if (os_tsk.run->events & wait_flags) {
+ os_tsk.run->waits = os_tsk.run->events & wait_flags;
+ os_tsk.run->events &= ~wait_flags;
+ return (OS_R_EVT);
+ }
+ block_state = WAIT_OR;
+ }
+ /* Task has to wait */
+ os_tsk.run->waits = wait_flags;
+ rt_block (timeout, (U8)block_state);
+ return (OS_R_TMO);
+}
+
+
+/*--------------------------- rt_evt_set ------------------------------------*/
+
+void rt_evt_set (U16 event_flags, OS_TID task_id) {
+ /* Set one or more event flags of a selectable task. */
+ P_TCB p_tcb;
+
+ p_tcb = os_active_TCB[task_id-1];
+ if (p_tcb == NULL) {
+ return;
+ }
+ p_tcb->events |= event_flags;
+ event_flags = p_tcb->waits;
+ /* If the task is not waiting for an event, it should not be put */
+ /* to ready state. */
+ if (p_tcb->state == WAIT_AND) {
+ /* Check for AND-connected events */
+ if ((p_tcb->events & event_flags) == event_flags) {
+ goto wkup;
+ }
+ }
+ if (p_tcb->state == WAIT_OR) {
+ /* Check for OR-connected events */
+ if (p_tcb->events & event_flags) {
+ p_tcb->waits &= p_tcb->events;
+wkup: p_tcb->events &= ~event_flags;
+ rt_rmv_dly (p_tcb);
+ p_tcb->state = READY;
+ rt_ret_val2(p_tcb, 0x08/*osEventSignal*/, p_tcb->waits);
+ rt_dispatch (p_tcb);
+ }
+ }
+}
+
+
+/*--------------------------- rt_evt_clr ------------------------------------*/
+
+void rt_evt_clr (U16 clear_flags, OS_TID task_id) {
+ /* Clear one or more event flags (identified by "clear_flags") of a */
+ /* selectable task (identified by "task"). */
+ P_TCB task = os_active_TCB[task_id-1];
+
+ if (task == NULL) {
+ return;
+ }
+ task->events &= ~clear_flags;
+}
+
+
+/*--------------------------- isr_evt_set -----------------------------------*/
+
+void isr_evt_set (U16 event_flags, OS_TID task_id) {
+ /* Same function as "os_evt_set", but to be called by ISRs. */
+ P_TCB p_tcb = os_active_TCB[task_id-1];
+
+ if (p_tcb == NULL) {
+ return;
+ }
+ rt_psq_enq (p_tcb, event_flags);
+ rt_psh_req ();
+}
+
+
+/*--------------------------- rt_evt_get ------------------------------------*/
+
+U16 rt_evt_get (void) {
+ /* Get events of a running task after waiting for OR connected events. */
+ return (os_tsk.run->waits);
+}
+
+
+/*--------------------------- rt_evt_psh ------------------------------------*/
+
+void rt_evt_psh (P_TCB p_CB, U16 set_flags) {
+ /* Check if task has to be waken up */
+ U16 event_flags;
+
+ p_CB->events |= set_flags;
+ event_flags = p_CB->waits;
+ if (p_CB->state == WAIT_AND) {
+ /* Check for AND-connected events */
+ if ((p_CB->events & event_flags) == event_flags) {
+ goto rdy;
+ }
+ }
+ if (p_CB->state == WAIT_OR) {
+ /* Check for OR-connected events */
+ if (p_CB->events & event_flags) {
+ p_CB->waits &= p_CB->events;
+rdy: p_CB->events &= ~event_flags;
+ rt_rmv_dly (p_CB);
+ p_CB->state = READY;
+ rt_ret_val2(p_CB, 0x08/*osEventSignal*/, p_CB->waits);
+ rt_put_prio (&os_rdy, p_CB);
+ }
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Event.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,46 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_EVENT.H + * Purpose: Implements waits and wake-ups for event flags + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Functions */ +extern OS_RESULT rt_evt_wait (U16 wait_flags, U16 timeout, BOOL and_wait); +extern void rt_evt_set (U16 event_flags, OS_TID task_id); +extern void rt_evt_clr (U16 clear_flags, OS_TID task_id); +extern void isr_evt_set (U16 event_flags, OS_TID task_id); +extern U16 rt_evt_get (void); +extern void rt_evt_psh (P_TCB p_CB, U16 set_flags); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_HAL_CM.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,267 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_HAL_CM.H
+ * Purpose: Hardware Abstraction Layer for Cortex-M definitions
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+/* Definitions */
+#define INITIAL_xPSR 0x01000000
+#define DEMCR_TRCENA 0x01000000
+#define ITM_ITMENA 0x00000001
+#define MAGIC_WORD 0xE25A2EA5
+
+#if defined (__CC_ARM) /* ARM Compiler */
+
+#if ((__TARGET_ARCH_7_M || __TARGET_ARCH_7E_M) && !NO_EXCLUSIVE_ACCESS)
+ #define __USE_EXCLUSIVE_ACCESS
+#else
+ #undef __USE_EXCLUSIVE_ACCESS
+#endif
+
+#elif defined (__GNUC__) /* GNU Compiler */
+
+#undef __USE_EXCLUSIVE_ACCESS
+
+#if defined (__CORTEX_M0)
+#define __TARGET_ARCH_6S_M 1
+#else
+#define __TARGET_ARCH_6S_M 0
+#endif
+
+#if defined (__VFP_FP__) && !defined(__SOFTFP__)
+#define __TARGET_FPU_VFP 1
+#else
+#define __TARGET_FPU_VFP 0
+#endif
+
+#define __inline inline
+#define __weak __attribute__((weak))
+
+#ifndef __CMSIS_GENERIC
+
+__attribute__((always_inline)) static inline void __enable_irq(void)
+{
+ __asm volatile ("cpsie i");
+}
+
+__attribute__((always_inline)) static inline U32 __disable_irq(void)
+{
+ U32 result;
+
+ __asm volatile ("mrs %0, primask" : "=r" (result));
+ __asm volatile ("cpsid i");
+ return(result & 1);
+}
+
+#endif
+
+__attribute__(( always_inline)) static inline U8 __clz(U32 value)
+{
+ U8 result;
+
+ __asm volatile ("clz %0, %1" : "=r" (result) : "r" (value));
+ return(result);
+}
+
+#elif defined (__ICCARM__) /* IAR Compiler */
+
+#undef __USE_EXCLUSIVE_ACCESS
+
+#if (__CORE__ == __ARM6M__)
+#define __TARGET_ARCH_6S_M 1
+#else
+#define __TARGET_ARCH_6S_M 0
+#endif
+
+#if defined __ARMVFP__
+#define __TARGET_FPU_VFP 1
+#else
+#define __TARGET_FPU_VFP 0
+#endif
+
+#define __inline inline
+
+#ifndef __CMSIS_GENERIC
+
+static inline void __enable_irq(void)
+{
+ __asm volatile ("cpsie i");
+}
+
+static inline U32 __disable_irq(void)
+{
+ U32 result;
+
+ __asm volatile ("mrs %0, primask" : "=r" (result));
+ __asm volatile ("cpsid i");
+ return(result & 1);
+}
+
+#endif
+
+static inline U8 __clz(U32 value)
+{
+ U8 result;
+
+ __asm volatile ("clz %0, %1" : "=r" (result) : "r" (value));
+ return(result);
+}
+
+#endif
+
+/* NVIC registers */
+#define NVIC_ST_CTRL (*((volatile U32 *)0xE000E010))
+#define NVIC_ST_RELOAD (*((volatile U32 *)0xE000E014))
+#define NVIC_ST_CURRENT (*((volatile U32 *)0xE000E018))
+#define NVIC_ISER ((volatile U32 *)0xE000E100)
+#define NVIC_ICER ((volatile U32 *)0xE000E180)
+#define NVIC_IP ((volatile U8 *)0xE000E400)
+#define NVIC_INT_CTRL (*((volatile U32 *)0xE000ED04))
+#define NVIC_AIR_CTRL (*((volatile U32 *)0xE000ED0C))
+#define NVIC_SYS_PRI2 (*((volatile U32 *)0xE000ED1C))
+#define NVIC_SYS_PRI3 (*((volatile U32 *)0xE000ED20))
+
+#define OS_PEND_IRQ() NVIC_INT_CTRL = (1<<28)
+#define OS_PENDING ((NVIC_INT_CTRL >> 26) & (1<<2 | 1))
+#define OS_UNPEND(fl) NVIC_INT_CTRL = (*fl = OS_PENDING) << 25
+#define OS_PEND(fl,p) NVIC_INT_CTRL = (fl | p<<2) << 26
+#define OS_LOCK() NVIC_ST_CTRL = 0x0005
+#define OS_UNLOCK() NVIC_ST_CTRL = 0x0007
+
+#define OS_X_PENDING ((NVIC_INT_CTRL >> 28) & 1)
+#define OS_X_UNPEND(fl) NVIC_INT_CTRL = (*fl = OS_X_PENDING) << 27
+#define OS_X_PEND(fl,p) NVIC_INT_CTRL = (fl | p) << 28
+#define OS_X_INIT(n) NVIC_IP[n] = 0xFF; \
+ NVIC_ISER[n>>5] = 1 << (n & 0x1F)
+#define OS_X_LOCK(n) NVIC_ICER[n>>5] = 1 << (n & 0x1F)
+#define OS_X_UNLOCK(n) NVIC_ISER[n>>5] = 1 << (n & 0x1F)
+
+/* Core Debug registers */
+#define DEMCR (*((volatile U32 *)0xE000EDFC))
+
+/* ITM registers */
+#define ITM_CONTROL (*((volatile U32 *)0xE0000E80))
+#define ITM_ENABLE (*((volatile U32 *)0xE0000E00))
+#define ITM_PORT30_U32 (*((volatile U32 *)0xE0000078))
+#define ITM_PORT31_U32 (*((volatile U32 *)0xE000007C))
+#define ITM_PORT31_U16 (*((volatile U16 *)0xE000007C))
+#define ITM_PORT31_U8 (*((volatile U8 *)0xE000007C))
+
+/* Variables */
+extern BIT dbg_msg;
+
+/* Functions */
+#ifdef __USE_EXCLUSIVE_ACCESS
+ #define rt_inc(p) while(__strex((__ldrex(p)+1),p))
+ #define rt_dec(p) while(__strex((__ldrex(p)-1),p))
+#else
+ #define rt_inc(p) __disable_irq();(*p)++;__enable_irq();
+ #define rt_dec(p) __disable_irq();(*p)--;__enable_irq();
+#endif
+
+__inline static U32 rt_inc_qi (U32 size, U8 *count, U8 *first) {
+ U32 cnt,c2;
+#ifdef __USE_EXCLUSIVE_ACCESS
+ do {
+ if ((cnt = __ldrex(count)) == size) {
+ __clrex();
+ return (cnt); }
+ } while (__strex(cnt+1, count));
+ do {
+ c2 = (cnt = __ldrex(first)) + 1;
+ if (c2 == size) c2 = 0;
+ } while (__strex(c2, first));
+#else
+ __disable_irq();
+ if ((cnt = *count) < size) {
+ *count = cnt+1;
+ c2 = (cnt = *first) + 1;
+ if (c2 == size) c2 = 0;
+ *first = c2;
+ }
+ __enable_irq ();
+#endif
+ return (cnt);
+}
+
+__inline static void rt_systick_init (void) {
+ NVIC_ST_RELOAD = os_trv;
+ NVIC_ST_CURRENT = 0;
+ NVIC_ST_CTRL = 0x0007;
+ NVIC_SYS_PRI3 |= 0xFF000000;
+}
+
+__inline static void rt_svc_init (void) {
+#if !(__TARGET_ARCH_6S_M)
+ int sh,prigroup;
+#endif
+ NVIC_SYS_PRI3 |= 0x00FF0000;
+#if (__TARGET_ARCH_6S_M)
+ NVIC_SYS_PRI2 |= (NVIC_SYS_PRI3<<(8+1)) & 0xFC000000;
+#else
+ sh = 8 - __clz (~((NVIC_SYS_PRI3 << 8) & 0xFF000000));
+ prigroup = ((NVIC_AIR_CTRL >> 8) & 0x07);
+ if (prigroup >= sh) {
+ sh = prigroup + 1;
+ }
+ NVIC_SYS_PRI2 = ((0xFEFFFFFF << sh) & 0xFF000000) | (NVIC_SYS_PRI2 & 0x00FFFFFF);
+#endif
+}
+
+extern void rt_set_PSP (U32 stack);
+extern U32 rt_get_PSP (void);
+extern void os_set_env (void);
+extern void *_alloc_box (void *box_mem);
+extern int _free_box (void *box_mem, void *box);
+
+extern void rt_init_stack (P_TCB p_TCB, FUNCP task_body);
+extern void rt_ret_val (P_TCB p_TCB, U32 v0);
+extern void rt_ret_val2 (P_TCB p_TCB, U32 v0, U32 v1);
+
+extern void dbg_init (void);
+extern void dbg_task_notify (P_TCB p_tcb, BOOL create);
+extern void dbg_task_switch (U32 task_id);
+
+#ifdef DBG_MSG
+#define DBG_INIT() dbg_init()
+#define DBG_TASK_NOTIFY(p_tcb,create) if (dbg_msg) dbg_task_notify(p_tcb,create)
+#define DBG_TASK_SWITCH(task_id) if (dbg_msg && (os_tsk.new!=os_tsk.run)) \
+ dbg_task_switch(task_id)
+#else
+#define DBG_INIT()
+#define DBG_TASK_NOTIFY(p_tcb,create)
+#define DBG_TASK_SWITCH(task_id)
+#endif
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_List.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,320 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_LIST.C
+ * Purpose: Functions for the management of different lists
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_List.h"
+#include "rt_Task.h"
+#include "rt_Time.h"
+#include "rt_HAL_CM.h"
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+/* List head of chained ready tasks */
+struct OS_XCB os_rdy;
+/* List head of chained delay tasks */
+struct OS_XCB os_dly;
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_put_prio -----------------------------------*/
+
+void rt_put_prio (P_XCB p_CB, P_TCB p_task) {
+ /* Put task identified with "p_task" into list ordered by priority. */
+ /* "p_CB" points to head of list; list has always an element at end with */
+ /* a priority less than "p_task->prio". */
+ P_TCB p_CB2;
+ U32 prio;
+ BOOL sem_mbx = __FALSE;
+
+ if (p_CB->cb_type == SCB || p_CB->cb_type == MCB || p_CB->cb_type == MUCB) {
+ sem_mbx = __TRUE;
+ }
+ prio = p_task->prio;
+ p_CB2 = p_CB->p_lnk;
+ /* Search for an entry in the list */
+ while (p_CB2 != NULL && prio <= p_CB2->prio) {
+ p_CB = (P_XCB)p_CB2;
+ p_CB2 = p_CB2->p_lnk;
+ }
+ /* Entry found, insert the task into the list */
+ p_task->p_lnk = p_CB2;
+ p_CB->p_lnk = p_task;
+ if (sem_mbx) {
+ if (p_CB2 != NULL) {
+ p_CB2->p_rlnk = p_task;
+ }
+ p_task->p_rlnk = (P_TCB)p_CB;
+ }
+ else {
+ p_task->p_rlnk = NULL;
+ }
+}
+
+
+/*--------------------------- rt_get_first ----------------------------------*/
+
+P_TCB rt_get_first (P_XCB p_CB) {
+ /* Get task at head of list: it is the task with highest priority. */
+ /* "p_CB" points to head of list. */
+ P_TCB p_first;
+
+ p_first = p_CB->p_lnk;
+ p_CB->p_lnk = p_first->p_lnk;
+ if (p_CB->cb_type == SCB || p_CB->cb_type == MCB || p_CB->cb_type == MUCB) {
+ if (p_first->p_lnk != NULL) {
+ p_first->p_lnk->p_rlnk = (P_TCB)p_CB;
+ p_first->p_lnk = NULL;
+ }
+ p_first->p_rlnk = NULL;
+ }
+ else {
+ p_first->p_lnk = NULL;
+ }
+ return (p_first);
+}
+
+
+/*--------------------------- rt_put_rdy_first ------------------------------*/
+
+void rt_put_rdy_first (P_TCB p_task) {
+ /* Put task identified with "p_task" at the head of the ready list. The */
+ /* task must have at least a priority equal to highest priority in list. */
+ p_task->p_lnk = os_rdy.p_lnk;
+ p_task->p_rlnk = NULL;
+ os_rdy.p_lnk = p_task;
+}
+
+
+/*--------------------------- rt_get_same_rdy_prio --------------------------*/
+
+P_TCB rt_get_same_rdy_prio (void) {
+ /* Remove a task of same priority from ready list if any exists. Other- */
+ /* wise return NULL. */
+ P_TCB p_first;
+
+ p_first = os_rdy.p_lnk;
+ if (p_first->prio == os_tsk.run->prio) {
+ os_rdy.p_lnk = os_rdy.p_lnk->p_lnk;
+ return (p_first);
+ }
+ return (NULL);
+}
+
+
+/*--------------------------- rt_resort_prio --------------------------------*/
+
+void rt_resort_prio (P_TCB p_task) {
+ /* Re-sort ordered lists after the priority of 'p_task' has changed. */
+ P_TCB p_CB;
+
+ if (p_task->p_rlnk == NULL) {
+ if (p_task->state == READY) {
+ /* Task is chained into READY list. */
+ p_CB = (P_TCB)&os_rdy;
+ goto res;
+ }
+ }
+ else {
+ p_CB = p_task->p_rlnk;
+ while (p_CB->cb_type == TCB) {
+ /* Find a header of this task chain list. */
+ p_CB = p_CB->p_rlnk;
+ }
+res:rt_rmv_list (p_task);
+ rt_put_prio ((P_XCB)p_CB, p_task);
+ }
+}
+
+
+/*--------------------------- rt_put_dly ------------------------------------*/
+
+void rt_put_dly (P_TCB p_task, U16 delay) {
+ /* Put a task identified with "p_task" into chained delay wait list using */
+ /* a delay value of "delay". */
+ P_TCB p;
+ U32 delta,idelay = delay;
+
+ p = (P_TCB)&os_dly;
+ if (p->p_dlnk == NULL) {
+ /* Delay list empty */
+ delta = 0;
+ goto last;
+ }
+ delta = os_dly.delta_time;
+ while (delta < idelay) {
+ if (p->p_dlnk == NULL) {
+ /* End of list found */
+last: p_task->p_dlnk = NULL;
+ p->p_dlnk = p_task;
+ p_task->p_blnk = p;
+ p->delta_time = (U16)(idelay - delta);
+ p_task->delta_time = 0;
+ return;
+ }
+ p = p->p_dlnk;
+ delta += p->delta_time;
+ }
+ /* Right place found */
+ p_task->p_dlnk = p->p_dlnk;
+ p->p_dlnk = p_task;
+ p_task->p_blnk = p;
+ if (p_task->p_dlnk != NULL) {
+ p_task->p_dlnk->p_blnk = p_task;
+ }
+ p_task->delta_time = (U16)(delta - idelay);
+ p->delta_time -= p_task->delta_time;
+}
+
+
+/*--------------------------- rt_dec_dly ------------------------------------*/
+
+void rt_dec_dly (void) {
+ /* Decrement delta time of list head: remove tasks having a value of zero.*/
+ P_TCB p_rdy;
+
+ if (os_dly.p_dlnk == NULL) {
+ return;
+ }
+ os_dly.delta_time--;
+ while ((os_dly.delta_time == 0) && (os_dly.p_dlnk != NULL)) {
+ p_rdy = os_dly.p_dlnk;
+ if (p_rdy->p_rlnk != NULL) {
+ /* Task is really enqueued, remove task from semaphore/mailbox */
+ /* timeout waiting list. */
+ p_rdy->p_rlnk->p_lnk = p_rdy->p_lnk;
+ if (p_rdy->p_lnk != NULL) {
+ p_rdy->p_lnk->p_rlnk = p_rdy->p_rlnk;
+ p_rdy->p_lnk = NULL;
+ }
+ p_rdy->p_rlnk = NULL;
+ }
+ rt_put_prio (&os_rdy, p_rdy);
+ os_dly.delta_time = p_rdy->delta_time;
+ if (p_rdy->state == WAIT_ITV) {
+ /* Calculate the next time for interval wait. */
+ p_rdy->delta_time = p_rdy->interval_time + (U16)os_time;
+ }
+ p_rdy->state = READY;
+ os_dly.p_dlnk = p_rdy->p_dlnk;
+ if (p_rdy->p_dlnk != NULL) {
+ p_rdy->p_dlnk->p_blnk = (P_TCB)&os_dly;
+ p_rdy->p_dlnk = NULL;
+ }
+ p_rdy->p_blnk = NULL;
+ }
+}
+
+
+/*--------------------------- rt_rmv_list -----------------------------------*/
+
+void rt_rmv_list (P_TCB p_task) {
+ /* Remove task identified with "p_task" from ready, semaphore or mailbox */
+ /* waiting list if enqueued. */
+ P_TCB p_b;
+
+ if (p_task->p_rlnk != NULL) {
+ /* A task is enqueued in semaphore / mailbox waiting list. */
+ p_task->p_rlnk->p_lnk = p_task->p_lnk;
+ if (p_task->p_lnk != NULL) {
+ p_task->p_lnk->p_rlnk = p_task->p_rlnk;
+ }
+ return;
+ }
+
+ p_b = (P_TCB)&os_rdy;
+ while (p_b != NULL) {
+ /* Search the ready list for task "p_task" */
+ if (p_b->p_lnk == p_task) {
+ p_b->p_lnk = p_task->p_lnk;
+ return;
+ }
+ p_b = p_b->p_lnk;
+ }
+}
+
+
+/*--------------------------- rt_rmv_dly ------------------------------------*/
+
+void rt_rmv_dly (P_TCB p_task) {
+ /* Remove task identified with "p_task" from delay list if enqueued. */
+ P_TCB p_b;
+
+ p_b = p_task->p_blnk;
+ if (p_b != NULL) {
+ /* Task is really enqueued */
+ p_b->p_dlnk = p_task->p_dlnk;
+ if (p_task->p_dlnk != NULL) {
+ /* 'p_task' is in the middle of list */
+ p_b->delta_time += p_task->delta_time;
+ p_task->p_dlnk->p_blnk = p_b;
+ p_task->p_dlnk = NULL;
+ }
+ else {
+ /* 'p_task' is at the end of list */
+ p_b->delta_time = 0;
+ }
+ p_task->p_blnk = NULL;
+ }
+}
+
+
+/*--------------------------- rt_psq_enq ------------------------------------*/
+
+void rt_psq_enq (OS_ID entry, U32 arg) {
+ /* Insert post service request "entry" into ps-queue. */
+ U32 idx;
+
+ idx = rt_inc_qi (os_psq->size, &os_psq->count, &os_psq->first);
+ if (idx < os_psq->size) {
+ os_psq->q[idx].id = entry;
+ os_psq->q[idx].arg = arg;
+ }
+ else {
+ os_error (OS_ERR_FIFO_OVF);
+ }
+}
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_List.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,67 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_LIST.H + * Purpose: Functions for the management of different lists + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Definitions */ + +/* Values for 'cb_type' */ +#define TCB 0 +#define MCB 1 +#define SCB 2 +#define MUCB 3 +#define HCB 4 + +/* Variables */ +extern struct OS_XCB os_rdy; +extern struct OS_XCB os_dly; + +/* Functions */ +extern void rt_put_prio (P_XCB p_CB, P_TCB p_task); +extern P_TCB rt_get_first (P_XCB p_CB); +extern void rt_put_rdy_first (P_TCB p_task); +extern P_TCB rt_get_same_rdy_prio (void); +extern void rt_resort_prio (P_TCB p_task); +extern void rt_put_dly (P_TCB p_task, U16 delay); +extern void rt_dec_dly (void); +extern void rt_rmv_list (P_TCB p_task); +extern void rt_rmv_dly (P_TCB p_task); +extern void rt_psq_enq (OS_ID entry, U32 arg); + +/* This is a fast macro generating in-line code */ +#define rt_rdy_prio(void) (os_rdy.p_lnk->prio) + + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Mailbox.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,285 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_MAILBOX.C
+ * Purpose: Implements waits and wake-ups for mailbox messages
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_List.h"
+#include "rt_Mailbox.h"
+#include "rt_MemBox.h"
+#include "rt_Task.h"
+#include "rt_HAL_CM.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_mbx_init -----------------------------------*/
+
+void rt_mbx_init (OS_ID mailbox, U16 mbx_size) {
+ /* Initialize a mailbox */
+ P_MCB p_MCB = mailbox;
+
+ p_MCB->cb_type = MCB;
+ p_MCB->state = 0;
+ p_MCB->isr_st = 0;
+ p_MCB->p_lnk = NULL;
+ p_MCB->first = 0;
+ p_MCB->last = 0;
+ p_MCB->count = 0;
+ p_MCB->size = (mbx_size + sizeof(void *) - sizeof(struct OS_MCB)) /
+ (U32)sizeof (void *);
+}
+
+
+/*--------------------------- rt_mbx_send -----------------------------------*/
+
+OS_RESULT rt_mbx_send (OS_ID mailbox, void *p_msg, U16 timeout) {
+ /* Send message to a mailbox */
+ P_MCB p_MCB = mailbox;
+ P_TCB p_TCB;
+
+ if (p_MCB->state == 1) {
+ /* A task is waiting for message */
+ p_TCB = rt_get_first ((P_XCB)p_MCB);
+ if (p_MCB->p_lnk == NULL) {
+ p_MCB->state = 0;
+ }
+ rt_ret_val2(p_TCB, 0x10/*osEventMessage*/, (U32)p_msg);
+ rt_rmv_dly (p_TCB);
+ rt_dispatch (p_TCB);
+ }
+ else {
+ /* Store message in mailbox queue */
+ if (p_MCB->count == p_MCB->size) {
+ /* No free message entry, wait for one. If message queue is full, */
+ /* then no task is waiting for message. The 'p_MCB->p_lnk' list */
+ /* pointer can now be reused for send message waits task list. */
+ if (timeout == 0) {
+ return (OS_R_TMO);
+ }
+ if (p_MCB->p_lnk != NULL) {
+ rt_put_prio ((P_XCB)p_MCB, os_tsk.run);
+ }
+ else {
+ p_MCB->p_lnk = os_tsk.run;
+ os_tsk.run->p_lnk = NULL;
+ os_tsk.run->p_rlnk = (P_TCB)p_MCB;
+ /* Task is waiting to send a message */
+ p_MCB->state = 2;
+ }
+ os_tsk.run->msg = p_msg;
+ rt_block (timeout, WAIT_MBX);
+ return (OS_R_TMO);
+ }
+ /* Yes, there is a free entry in a mailbox. */
+ p_MCB->msg[p_MCB->first] = p_msg;
+ rt_inc (&p_MCB->count);
+ if (++p_MCB->first == p_MCB->size) {
+ p_MCB->first = 0;
+ }
+ }
+ return (OS_R_OK);
+}
+
+
+/*--------------------------- rt_mbx_wait -----------------------------------*/
+
+OS_RESULT rt_mbx_wait (OS_ID mailbox, void **message, U16 timeout) {
+ /* Receive a message; possibly wait for it */
+ P_MCB p_MCB = mailbox;
+ P_TCB p_TCB;
+
+ /* If a message is available in the fifo buffer */
+ /* remove it from the fifo buffer and return. */
+ if (p_MCB->count) {
+ *message = p_MCB->msg[p_MCB->last];
+ if (++p_MCB->last == p_MCB->size) {
+ p_MCB->last = 0;
+ }
+ if (p_MCB->state == 2) {
+ /* A task is waiting to send message */
+ p_TCB = rt_get_first ((P_XCB)p_MCB);
+ if (p_MCB->p_lnk == NULL) {
+ p_MCB->state = 0;
+ }
+ rt_ret_val(p_TCB, 0/*osOK*/);
+ p_MCB->msg[p_MCB->first] = p_TCB->msg;
+ if (++p_MCB->first == p_MCB->size) {
+ p_MCB->first = 0;
+ }
+ rt_rmv_dly (p_TCB);
+ rt_dispatch (p_TCB);
+ }
+ else {
+ rt_dec (&p_MCB->count);
+ }
+ return (OS_R_OK);
+ }
+ /* No message available: wait for one */
+ if (timeout == 0) {
+ return (OS_R_TMO);
+ }
+ if (p_MCB->p_lnk != NULL) {
+ rt_put_prio ((P_XCB)p_MCB, os_tsk.run);
+ }
+ else {
+ p_MCB->p_lnk = os_tsk.run;
+ os_tsk.run->p_lnk = NULL;
+ os_tsk.run->p_rlnk = (P_TCB)p_MCB;
+ /* Task is waiting to receive a message */
+ p_MCB->state = 1;
+ }
+ rt_block(timeout, WAIT_MBX);
+ return (OS_R_TMO);
+}
+
+
+/*--------------------------- rt_mbx_check ----------------------------------*/
+
+OS_RESULT rt_mbx_check (OS_ID mailbox) {
+ /* Check for free space in a mailbox. Returns the number of messages */
+ /* that can be stored to a mailbox. It returns 0 when mailbox is full. */
+ P_MCB p_MCB = mailbox;
+
+ return (p_MCB->size - p_MCB->count);
+}
+
+
+/*--------------------------- isr_mbx_send ----------------------------------*/
+
+void isr_mbx_send (OS_ID mailbox, void *p_msg) {
+ /* Same function as "os_mbx_send", but to be called by ISRs. */
+ P_MCB p_MCB = mailbox;
+
+ rt_psq_enq (p_MCB, (U32)p_msg);
+ rt_psh_req ();
+}
+
+
+/*--------------------------- isr_mbx_receive -------------------------------*/
+
+OS_RESULT isr_mbx_receive (OS_ID mailbox, void **message) {
+ /* Receive a message in the interrupt function. The interrupt function */
+ /* should not wait for a message since this would block the rtx os. */
+ P_MCB p_MCB = mailbox;
+
+ if (p_MCB->count) {
+ /* A message is available in the fifo buffer. */
+ *message = p_MCB->msg[p_MCB->last];
+ if (p_MCB->state == 2) {
+ /* A task is locked waiting to send message */
+ rt_psq_enq (p_MCB, 0);
+ rt_psh_req ();
+ }
+ rt_dec (&p_MCB->count);
+ if (++p_MCB->last == p_MCB->size) {
+ p_MCB->last = 0;
+ }
+ return (OS_R_MBX);
+ }
+ return (OS_R_OK);
+}
+
+
+/*--------------------------- rt_mbx_psh ------------------------------------*/
+
+void rt_mbx_psh (P_MCB p_CB, void *p_msg) {
+ /* Store the message to the mailbox queue or pass it to task directly. */
+ P_TCB p_TCB;
+ void *mem;
+
+ switch (p_CB->state) {
+ case 3:
+ /* Task is waiting to allocate memory, remove it from the waiting list */
+ mem = rt_alloc_box(p_msg);
+ if (mem == NULL) break;
+ p_TCB = rt_get_first ((P_XCB)p_CB);
+ if (p_CB->p_lnk == NULL) {
+ p_CB->state = 0;
+ }
+ rt_ret_val(p_TCB, (U32)mem);
+ p_TCB->state = READY;
+ rt_rmv_dly (p_TCB);
+ rt_put_prio (&os_rdy, p_TCB);
+ break;
+ case 2:
+ /* Task is waiting to send a message, remove it from the waiting list */
+ p_TCB = rt_get_first ((P_XCB)p_CB);
+ if (p_CB->p_lnk == NULL) {
+ p_CB->state = 0;
+ }
+ rt_ret_val(p_TCB, 0/*osOK*/);
+ p_CB->msg[p_CB->first] = p_TCB->msg;
+ rt_inc (&p_CB->count);
+ if (++p_CB->first == p_CB->size) {
+ p_CB->first = 0;
+ }
+ p_TCB->state = READY;
+ rt_rmv_dly (p_TCB);
+ rt_put_prio (&os_rdy, p_TCB);
+ break;
+ case 1:
+ /* Task is waiting for a message, pass the message to the task directly */
+ p_TCB = rt_get_first ((P_XCB)p_CB);
+ if (p_CB->p_lnk == NULL) {
+ p_CB->state = 0;
+ }
+ rt_ret_val2(p_TCB, 0x10/*osEventMessage*/, (U32)p_msg);
+ p_TCB->state = READY;
+ rt_rmv_dly (p_TCB);
+ rt_put_prio (&os_rdy, p_TCB);
+ break;
+ default:
+ /* No task is waiting for a message, store it to the mailbox queue */
+ if (p_CB->count < p_CB->size) {
+ p_CB->msg[p_CB->first] = p_msg;
+ rt_inc (&p_CB->count);
+ if (++p_CB->first == p_CB->size) {
+ p_CB->first = 0;
+ }
+ }
+ else {
+ os_error (OS_ERR_MBX_OVF);
+ }
+ break;
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Mailbox.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,48 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_MAILBOX.H + * Purpose: Implements waits and wake-ups for mailbox messages + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Functions */ +extern void rt_mbx_init (OS_ID mailbox, U16 mbx_size); +extern OS_RESULT rt_mbx_send (OS_ID mailbox, void *p_msg, U16 timeout); +extern OS_RESULT rt_mbx_wait (OS_ID mailbox, void **message, U16 timeout); +extern OS_RESULT rt_mbx_check (OS_ID mailbox); +extern void isr_mbx_send (OS_ID mailbox, void *p_msg); +extern OS_RESULT isr_mbx_receive (OS_ID mailbox, void **message); +extern void rt_mbx_psh (P_MCB p_CB, void *p_msg); + + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_MemBox.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,166 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_MEMBOX.C
+ * Purpose: Interface functions for fixed memory block management system
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_MemBox.h"
+#include "rt_HAL_CM.h"
+
+/*----------------------------------------------------------------------------
+ * Global Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- _init_box -------------------------------------*/
+
+int _init_box (void *box_mem, U32 box_size, U32 blk_size) {
+ /* Initialize memory block system, returns 0 if OK, 1 if fails. */
+ void *end;
+ void *blk;
+ void *next;
+ U32 sizeof_bm;
+
+ /* Create memory structure. */
+ if (blk_size & BOX_ALIGN_8) {
+ /* Memory blocks 8-byte aligned. */
+ blk_size = ((blk_size & ~BOX_ALIGN_8) + 7) & ~7;
+ sizeof_bm = (sizeof (struct OS_BM) + 7) & ~7;
+ }
+ else {
+ /* Memory blocks 4-byte aligned. */
+ blk_size = (blk_size + 3) & ~3;
+ sizeof_bm = sizeof (struct OS_BM);
+ }
+ if (blk_size == 0) {
+ return (1);
+ }
+ if ((blk_size + sizeof_bm) > box_size) {
+ return (1);
+ }
+ /* Create a Memory structure. */
+ blk = ((U8 *) box_mem) + sizeof_bm;
+ ((P_BM) box_mem)->free = blk;
+ end = ((U8 *) box_mem) + box_size;
+ ((P_BM) box_mem)->end = end;
+ ((P_BM) box_mem)->blk_size = blk_size;
+
+ /* Link all free blocks using offsets. */
+ end = ((U8 *) end) - blk_size;
+ while (1) {
+ next = ((U8 *) blk) + blk_size;
+ if (next > end) break;
+ *((void **)blk) = next;
+ blk = next;
+ }
+ /* end marker */
+ *((void **)blk) = 0;
+ return (0);
+}
+
+/*--------------------------- rt_alloc_box ----------------------------------*/
+
+void *rt_alloc_box (void *box_mem) {
+ /* Allocate a memory block and return start address. */
+ void **free;
+#ifndef __USE_EXCLUSIVE_ACCESS
+ int irq_dis;
+
+ irq_dis = __disable_irq ();
+ free = ((P_BM) box_mem)->free;
+ if (free) {
+ ((P_BM) box_mem)->free = *free;
+ }
+ if (!irq_dis) __enable_irq ();
+#else
+ do {
+ if ((free = (void **)__ldrex(&((P_BM) box_mem)->free)) == 0) {
+ __clrex();
+ break;
+ }
+ } while (__strex((U32)*free, &((P_BM) box_mem)->free));
+#endif
+ return (free);
+}
+
+
+/*--------------------------- _calloc_box -----------------------------------*/
+
+void *_calloc_box (void *box_mem) {
+ /* Allocate a 0-initialized memory block and return start address. */
+ void *free;
+ U32 *p;
+ U32 i;
+
+ free = _alloc_box (box_mem);
+ if (free) {
+ p = free;
+ for (i = ((P_BM) box_mem)->blk_size; i; i -= 4) {
+ *p = 0;
+ p++;
+ }
+ }
+ return (free);
+}
+
+
+/*--------------------------- rt_free_box -----------------------------------*/
+
+int rt_free_box (void *box_mem, void *box) {
+ /* Free a memory block, returns 0 if OK, 1 if box does not belong to box_mem */
+#ifndef __USE_EXCLUSIVE_ACCESS
+ int irq_dis;
+#endif
+
+ if (box < box_mem || box >= ((P_BM) box_mem)->end) {
+ return (1);
+ }
+
+#ifndef __USE_EXCLUSIVE_ACCESS
+ irq_dis = __disable_irq ();
+ *((void **)box) = ((P_BM) box_mem)->free;
+ ((P_BM) box_mem)->free = box;
+ if (!irq_dis) __enable_irq ();
+#else
+ do {
+ *((void **)box) = (void *)__ldrex(&((P_BM) box_mem)->free);
+ } while (__strex ((U32)box, &((P_BM) box_mem)->free));
+#endif
+ return (0);
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_MemBox.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,46 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_MEMBOX.H + * Purpose: Interface functions for fixed memory block management system + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Functions */ +#define rt_init_box _init_box +#define rt_calloc_box _calloc_box +extern int _init_box (void *box_mem, U32 box_size, U32 blk_size); +extern void *rt_alloc_box (void *box_mem); +extern void * _calloc_box (void *box_mem); +extern int rt_free_box (void *box_mem, void *box); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Mutex.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,189 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_MUTEX.C
+ * Purpose: Implements mutex synchronization objects
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_List.h"
+#include "rt_Task.h"
+#include "rt_Mutex.h"
+#include "rt_HAL_CM.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_mut_init -----------------------------------*/
+
+void rt_mut_init (OS_ID mutex) {
+ /* Initialize a mutex object */
+ P_MUCB p_MCB = mutex;
+
+ p_MCB->cb_type = MUCB;
+ p_MCB->prio = 0;
+ p_MCB->level = 0;
+ p_MCB->p_lnk = NULL;
+ p_MCB->owner = NULL;
+}
+
+
+/*--------------------------- rt_mut_delete ---------------------------------*/
+OS_RESULT rt_mut_delete (OS_ID mutex) {
+ /* Delete a mutex object */
+ P_MUCB p_MCB = mutex;
+ P_TCB p_TCB;
+
+ /* Restore owner task's priority. */
+ if (p_MCB->level != 0) {
+ p_MCB->owner->prio = p_MCB->prio;
+ if (p_MCB->owner != os_tsk.run) {
+ rt_resort_prio (p_MCB->owner);
+ }
+ }
+
+ while (p_MCB->p_lnk != NULL) {
+ /* A task is waiting for mutex. */
+ p_TCB = rt_get_first ((P_XCB)p_MCB);
+ rt_ret_val(p_TCB, 0/*osOK*/);
+ rt_rmv_dly(p_TCB);
+ p_TCB->state = READY;
+ rt_put_prio (&os_rdy, p_TCB);
+ }
+
+ if (os_rdy.p_lnk && (os_rdy.p_lnk->prio > os_tsk.run->prio)) {
+ /* preempt running task */
+ rt_put_prio (&os_rdy, os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_dispatch (NULL);
+ }
+
+ p_MCB->cb_type = 0;
+
+ return (OS_R_OK);
+}
+
+/*--------------------------- rt_mut_release --------------------------------*/
+
+OS_RESULT rt_mut_release (OS_ID mutex) {
+ /* Release a mutex object */
+ P_MUCB p_MCB = mutex;
+ P_TCB p_TCB;
+
+ if (p_MCB->level == 0 || p_MCB->owner != os_tsk.run) {
+ /* Unbalanced mutex release or task is not the owner */
+ return (OS_R_NOK);
+ }
+ if (--p_MCB->level != 0) {
+ return (OS_R_OK);
+ }
+ /* Restore owner task's priority. */
+ os_tsk.run->prio = p_MCB->prio;
+ if (p_MCB->p_lnk != NULL) {
+ /* A task is waiting for mutex. */
+ p_TCB = rt_get_first ((P_XCB)p_MCB);
+ rt_ret_val(p_TCB, 0/*osOK*/);
+ rt_rmv_dly (p_TCB);
+ /* A waiting task becomes the owner of this mutex. */
+ p_MCB->level = 1;
+ p_MCB->owner = p_TCB;
+ p_MCB->prio = p_TCB->prio;
+ /* Priority inversion, check which task continues. */
+ if (os_tsk.run->prio >= rt_rdy_prio()) {
+ rt_dispatch (p_TCB);
+ }
+ else {
+ /* Ready task has higher priority than running task. */
+ rt_put_prio (&os_rdy, os_tsk.run);
+ rt_put_prio (&os_rdy, p_TCB);
+ os_tsk.run->state = READY;
+ p_TCB->state = READY;
+ rt_dispatch (NULL);
+ }
+ }
+ else {
+ /* Check if own priority raised by priority inversion. */
+ if (rt_rdy_prio() > os_tsk.run->prio) {
+ rt_put_prio (&os_rdy, os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_dispatch (NULL);
+ }
+ }
+ return (OS_R_OK);
+}
+
+
+/*--------------------------- rt_mut_wait -----------------------------------*/
+
+OS_RESULT rt_mut_wait (OS_ID mutex, U16 timeout) {
+ /* Wait for a mutex, continue when mutex is free. */
+ P_MUCB p_MCB = mutex;
+
+ if (p_MCB->level == 0) {
+ p_MCB->owner = os_tsk.run;
+ p_MCB->prio = os_tsk.run->prio;
+ goto inc;
+ }
+ if (p_MCB->owner == os_tsk.run) {
+ /* OK, running task is the owner of this mutex. */
+inc:p_MCB->level++;
+ return (OS_R_OK);
+ }
+ /* Mutex owned by another task, wait until released. */
+ if (timeout == 0) {
+ return (OS_R_TMO);
+ }
+ /* Raise the owner task priority if lower than current priority. */
+ /* This priority inversion is called priority inheritance. */
+ if (p_MCB->prio < os_tsk.run->prio) {
+ p_MCB->owner->prio = os_tsk.run->prio;
+ rt_resort_prio (p_MCB->owner);
+ }
+ if (p_MCB->p_lnk != NULL) {
+ rt_put_prio ((P_XCB)p_MCB, os_tsk.run);
+ }
+ else {
+ p_MCB->p_lnk = os_tsk.run;
+ os_tsk.run->p_lnk = NULL;
+ os_tsk.run->p_rlnk = (P_TCB)p_MCB;
+ }
+ rt_block(timeout, WAIT_MUT);
+ return (OS_R_TMO);
+}
+
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Mutex.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,44 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_MUTEX.H + * Purpose: Implements mutex synchronization objects + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Functions */ +extern void rt_mut_init (OS_ID mutex); +extern OS_RESULT rt_mut_delete (OS_ID mutex); +extern OS_RESULT rt_mut_release (OS_ID mutex); +extern OS_RESULT rt_mut_wait (OS_ID mutex, U16 timeout); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Robin.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,84 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_ROBIN.C
+ * Purpose: Round Robin Task switching
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_List.h"
+#include "rt_Task.h"
+#include "rt_Time.h"
+#include "rt_Robin.h"
+#include "rt_HAL_CM.h"
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+struct OS_ROBIN os_robin;
+
+
+/*----------------------------------------------------------------------------
+ * Global Functions
+ *---------------------------------------------------------------------------*/
+
+/*--------------------------- rt_init_robin ---------------------------------*/
+
+__weak void rt_init_robin (void) {
+ /* Initialize Round Robin variables. */
+ os_robin.task = NULL;
+ os_robin.tout = (U16)os_rrobin;
+}
+
+/*--------------------------- rt_chk_robin ----------------------------------*/
+
+__weak void rt_chk_robin (void) {
+ /* Check if Round Robin timeout expired and switch to the next ready task.*/
+ P_TCB p_new;
+
+ if (os_robin.task != os_rdy.p_lnk) {
+ /* New task was suspended, reset Round Robin timeout. */
+ os_robin.task = os_rdy.p_lnk;
+ os_robin.time = (U16)os_time + os_robin.tout - 1;
+ }
+ if (os_robin.time == (U16)os_time) {
+ /* Round Robin timeout has expired, swap Robin tasks. */
+ os_robin.task = NULL;
+ p_new = rt_get_first (&os_rdy);
+ rt_put_prio ((P_XCB)&os_rdy, p_new);
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Robin.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,45 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_ROBIN.H + * Purpose: Round Robin Task switching definitions + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Variables */ +extern struct OS_ROBIN os_robin; + +/* Functions */ +extern void rt_init_robin (void); +extern void rt_chk_robin (void); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Semaphore.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,171 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_SEMAPHORE.C
+ * Purpose: Implements binary and counting semaphores
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_List.h"
+#include "rt_Task.h"
+#include "rt_Semaphore.h"
+#include "rt_HAL_CM.h"
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_sem_init -----------------------------------*/
+
+void rt_sem_init (OS_ID semaphore, U16 token_count) {
+ /* Initialize a semaphore */
+ P_SCB p_SCB = semaphore;
+
+ p_SCB->cb_type = SCB;
+ p_SCB->p_lnk = NULL;
+ p_SCB->tokens = token_count;
+}
+
+
+/*--------------------------- rt_sem_delete ---------------------------------*/
+OS_RESULT rt_sem_delete (OS_ID semaphore) {
+ /* Delete semaphore */
+ P_SCB p_SCB = semaphore;
+ P_TCB p_TCB;
+
+ while (p_SCB->p_lnk != NULL) {
+ /* A task is waiting for token */
+ p_TCB = rt_get_first ((P_XCB)p_SCB);
+ rt_ret_val(p_TCB, 0);
+ rt_rmv_dly(p_TCB);
+ p_TCB->state = READY;
+ rt_put_prio (&os_rdy, p_TCB);
+ }
+
+ if (os_rdy.p_lnk && (os_rdy.p_lnk->prio > os_tsk.run->prio)) {
+ /* preempt running task */
+ rt_put_prio (&os_rdy, os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_dispatch (NULL);
+ }
+
+ p_SCB->cb_type = 0;
+
+ return (OS_R_OK);
+}
+
+/*--------------------------- rt_sem_send -----------------------------------*/
+
+OS_RESULT rt_sem_send (OS_ID semaphore) {
+ /* Return a token to semaphore */
+ P_SCB p_SCB = semaphore;
+ P_TCB p_TCB;
+
+ if (p_SCB->p_lnk != NULL) {
+ /* A task is waiting for token */
+ p_TCB = rt_get_first ((P_XCB)p_SCB);
+ rt_ret_val(p_TCB, 1);
+ rt_rmv_dly (p_TCB);
+ rt_dispatch (p_TCB);
+ }
+ else {
+ /* Store token. */
+ p_SCB->tokens++;
+ }
+ return (OS_R_OK);
+}
+
+
+/*--------------------------- rt_sem_wait -----------------------------------*/
+
+OS_RESULT rt_sem_wait (OS_ID semaphore, U16 timeout) {
+ /* Obtain a token; possibly wait for it */
+ P_SCB p_SCB = semaphore;
+
+ if (p_SCB->tokens) {
+ p_SCB->tokens--;
+ return (OS_R_OK);
+ }
+ /* No token available: wait for one */
+ if (timeout == 0) {
+ return (OS_R_TMO);
+ }
+ if (p_SCB->p_lnk != NULL) {
+ rt_put_prio ((P_XCB)p_SCB, os_tsk.run);
+ }
+ else {
+ p_SCB->p_lnk = os_tsk.run;
+ os_tsk.run->p_lnk = NULL;
+ os_tsk.run->p_rlnk = (P_TCB)p_SCB;
+ }
+ rt_block(timeout, WAIT_SEM);
+ return (OS_R_TMO);
+}
+
+
+/*--------------------------- isr_sem_send ----------------------------------*/
+
+void isr_sem_send (OS_ID semaphore) {
+ /* Same function as "os_sem"send", but to be called by ISRs */
+ P_SCB p_SCB = semaphore;
+
+ rt_psq_enq (p_SCB, 0);
+ rt_psh_req ();
+}
+
+
+/*--------------------------- rt_sem_psh ------------------------------------*/
+
+void rt_sem_psh (P_SCB p_CB) {
+ /* Check if task has to be waken up */
+ P_TCB p_TCB;
+
+ if (p_CB->p_lnk != NULL) {
+ /* A task is waiting for token */
+ p_TCB = rt_get_first ((P_XCB)p_CB);
+ rt_rmv_dly (p_TCB);
+ p_TCB->state = READY;
+ rt_ret_val(p_TCB, 1);
+ rt_put_prio (&os_rdy, p_TCB);
+ }
+ else {
+ /* Store token */
+ p_CB->tokens++;
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Semaphore.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,46 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_SEMAPHORE.H + * Purpose: Implements binary and counting semaphores + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Functions */ +extern void rt_sem_init (OS_ID semaphore, U16 token_count); +extern OS_RESULT rt_sem_delete(OS_ID semaphore); +extern OS_RESULT rt_sem_send (OS_ID semaphore); +extern OS_RESULT rt_sem_wait (OS_ID semaphore, U16 timeout); +extern void isr_sem_send (OS_ID semaphore); +extern void rt_sem_psh (P_SCB p_CB); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_System.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,288 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_SYSTEM.C
+ * Purpose: System Task Manager
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_Task.h"
+#include "rt_System.h"
+#include "rt_Event.h"
+#include "rt_List.h"
+#include "rt_Mailbox.h"
+#include "rt_Semaphore.h"
+#include "rt_Time.h"
+#include "rt_Robin.h"
+#include "rt_HAL_CM.h"
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+int os_tick_irqn;
+
+/*----------------------------------------------------------------------------
+ * Local Variables
+ *---------------------------------------------------------------------------*/
+
+static volatile BIT os_lock;
+static volatile BIT os_psh_flag;
+static U8 pend_flags;
+
+/*----------------------------------------------------------------------------
+ * Global Functions
+ *---------------------------------------------------------------------------*/
+
+#if defined (__CC_ARM)
+__asm void $$RTX$$version (void) {
+ /* Export a version number symbol for a version control. */
+
+ EXPORT __RL_RTX_VER
+
+__RL_RTX_VER EQU 0x450
+}
+#endif
+
+
+/*--------------------------- rt_suspend ------------------------------------*/
+U32 rt_suspend (void) {
+ /* Suspend OS scheduler */
+ U32 delta = 0xFFFF;
+
+ rt_tsk_lock();
+
+ if (os_dly.p_dlnk) {
+ delta = os_dly.delta_time;
+ }
+
+ return (delta);
+}
+
+
+/*--------------------------- rt_resume -------------------------------------*/
+void rt_resume (U32 sleep_time) {
+ /* Resume OS scheduler after suspend */
+ P_TCB next;
+ U32 delta;
+
+ os_tsk.run->state = READY;
+ rt_put_rdy_first (os_tsk.run);
+
+ os_robin.task = NULL;
+
+ /* Update delays. */
+ if (os_dly.p_dlnk) {
+ delta = sleep_time;
+ if (delta >= os_dly.delta_time) {
+ delta -= os_dly.delta_time;
+ os_time += os_dly.delta_time;
+ os_dly.delta_time = 1;
+ while (os_dly.p_dlnk) {
+ rt_dec_dly();
+ if (delta == 0) break;
+ delta--;
+ os_time++;
+ }
+ } else {
+ os_time += delta;
+ os_dly.delta_time -= delta;
+ }
+ } else {
+ os_time += sleep_time;
+ }
+
+ /* Switch back to highest ready task */
+ next = rt_get_first (&os_rdy);
+ rt_switch_req (next);
+
+ rt_tsk_unlock();
+}
+
+
+/*--------------------------- rt_tsk_lock -----------------------------------*/
+
+void rt_tsk_lock (void) {
+ /* Prevent task switching by locking out scheduler */
+ if (os_tick_irqn < 0) {
+ OS_LOCK();
+ os_lock = __TRUE;
+ OS_UNPEND (&pend_flags);
+ } else {
+ OS_X_LOCK(os_tick_irqn);
+ os_lock = __TRUE;
+ OS_X_UNPEND (&pend_flags);
+ }
+}
+
+
+/*--------------------------- rt_tsk_unlock ---------------------------------*/
+
+void rt_tsk_unlock (void) {
+ /* Unlock scheduler and re-enable task switching */
+ if (os_tick_irqn < 0) {
+ OS_UNLOCK();
+ os_lock = __FALSE;
+ OS_PEND (pend_flags, os_psh_flag);
+ os_psh_flag = __FALSE;
+ } else {
+ OS_X_UNLOCK(os_tick_irqn);
+ os_lock = __FALSE;
+ OS_X_PEND (pend_flags, os_psh_flag);
+ os_psh_flag = __FALSE;
+ }
+}
+
+
+/*--------------------------- rt_psh_req ------------------------------------*/
+
+void rt_psh_req (void) {
+ /* Initiate a post service handling request if required. */
+ if (os_lock == __FALSE) {
+ OS_PEND_IRQ ();
+ }
+ else {
+ os_psh_flag = __TRUE;
+ }
+}
+
+
+/*--------------------------- rt_pop_req ------------------------------------*/
+
+void rt_pop_req (void) {
+ /* Process an ISR post service requests. */
+ struct OS_XCB *p_CB;
+ P_TCB next;
+ U32 idx;
+
+ os_tsk.run->state = READY;
+ rt_put_rdy_first (os_tsk.run);
+
+ idx = os_psq->last;
+ while (os_psq->count) {
+ p_CB = os_psq->q[idx].id;
+ if (p_CB->cb_type == TCB) {
+ /* Is of TCB type */
+ rt_evt_psh ((P_TCB)p_CB, (U16)os_psq->q[idx].arg);
+ }
+ else if (p_CB->cb_type == MCB) {
+ /* Is of MCB type */
+ rt_mbx_psh ((P_MCB)p_CB, (void *)os_psq->q[idx].arg);
+ }
+ else {
+ /* Must be of SCB type */
+ rt_sem_psh ((P_SCB)p_CB);
+ }
+ if (++idx == os_psq->size) idx = 0;
+ rt_dec (&os_psq->count);
+ }
+ os_psq->last = idx;
+
+ next = rt_get_first (&os_rdy);
+ rt_switch_req (next);
+}
+
+
+/*--------------------------- os_tick_init ----------------------------------*/
+
+__weak int os_tick_init (void) {
+ /* Initialize SysTick timer as system tick timer. */
+ rt_systick_init ();
+ return (-1); /* Return IRQ number of SysTick timer */
+}
+
+
+/*--------------------------- os_tick_irqack --------------------------------*/
+
+__weak void os_tick_irqack (void) {
+ /* Acknowledge timer interrupt. */
+}
+
+
+/*--------------------------- rt_systick ------------------------------------*/
+
+extern void sysTimerTick(void);
+
+void rt_systick (void) {
+ /* Check for system clock update, suspend running task. */
+ P_TCB next;
+
+ os_tsk.run->state = READY;
+ rt_put_rdy_first (os_tsk.run);
+
+ /* Check Round Robin timeout. */
+ rt_chk_robin ();
+
+ /* Update delays. */
+ os_time++;
+ rt_dec_dly ();
+
+ /* Check the user timers. */
+ sysTimerTick();
+
+ /* Switch back to highest ready task */
+ next = rt_get_first (&os_rdy);
+ rt_switch_req (next);
+}
+
+/*--------------------------- rt_stk_check ----------------------------------*/
+#ifdef THREAD_STACK_DIAGNOSTIC
+typedef struct stack_boundaries_s {
+ unsigned int top;
+ unsigned int min;
+} stack_boundaries_t;
+stack_boundaries_t stack_boundaries[256];
+#endif
+
+__weak void rt_stk_check (void) {
+#ifdef THREAD_STACK_DIAGNOSTIC
+ stack_boundaries_t* sb = &stack_boundaries[os_tsk.run->task_id];
+ if (sb->top == 0) {
+ sb->top = (unsigned int)os_tsk.run->stack + os_tsk.run->priv_stack;
+ }
+ if ((sb->min == 0) || (sb->min < os_tsk.run->tsk_stack))
+ sb->min = os_tsk.run->tsk_stack;
+#endif
+ /* Check for stack overflow */
+ if (os_tsk.run->task_id == 0x01) {
+ // TODO: For the main thread the check should be done against the heap pointer
+ } else {
+ if ((os_tsk.run->tsk_stack < (U32)os_tsk.run->stack) ||
+ (os_tsk.run->stack[0] != MAGIC_WORD)) {
+ os_error (OS_ERR_STK_OVF);
+ }
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_System.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,52 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_SYSTEM.H + * Purpose: System Task Manager definitions + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Variables */ +#define os_psq ((P_PSQ)&os_fifo) +extern int os_tick_irqn; + +/* Functions */ +extern U32 rt_suspend (void); +extern void rt_resume (U32 sleep_time); +extern void rt_tsk_lock (void); +extern void rt_tsk_unlock (void); +extern void rt_psh_req (void); +extern void rt_pop_req (void); +extern void rt_systick (void); +extern void rt_stk_check (void); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Task.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,317 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_TASK.C
+ * Purpose: Task functions and system start up.
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_System.h"
+#include "rt_Task.h"
+#include "rt_List.h"
+#include "rt_MemBox.h"
+#include "rt_Robin.h"
+#include "rt_HAL_CM.h"
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+/* Running and next task info. */
+struct OS_TSK os_tsk;
+
+/* Task Control Blocks of idle demon */
+struct OS_TCB os_idle_TCB;
+
+
+/*----------------------------------------------------------------------------
+ * Local Functions
+ *---------------------------------------------------------------------------*/
+
+OS_TID rt_get_TID (void) {
+ U32 tid;
+
+ for (tid = 1; tid <= os_maxtaskrun; tid++) {
+ if (os_active_TCB[tid-1] == NULL) {
+ return ((OS_TID)tid);
+ }
+ }
+ return (0);
+}
+
+#if defined (__CC_ARM) && !defined (__MICROLIB)
+/*--------------------------- __user_perthread_libspace ---------------------*/
+extern void *__libspace_start;
+
+void *__user_perthread_libspace (void) {
+ /* Provide a separate libspace for each task. */
+ if (os_tsk.run == NULL) {
+ /* RTX not running yet. */
+ return (&__libspace_start);
+ }
+ return (void *)(os_tsk.run->std_libspace);
+}
+#endif
+
+/*--------------------------- rt_init_context -------------------------------*/
+
+void rt_init_context (P_TCB p_TCB, U8 priority, FUNCP task_body) {
+ /* Initialize general part of the Task Control Block. */
+ p_TCB->cb_type = TCB;
+ p_TCB->state = READY;
+ p_TCB->prio = priority;
+ p_TCB->p_lnk = NULL;
+ p_TCB->p_rlnk = NULL;
+ p_TCB->p_dlnk = NULL;
+ p_TCB->p_blnk = NULL;
+ p_TCB->delta_time = 0;
+ p_TCB->interval_time = 0;
+ p_TCB->events = 0;
+ p_TCB->waits = 0;
+ p_TCB->stack_frame = 0;
+
+ rt_init_stack (p_TCB, task_body);
+}
+
+
+/*--------------------------- rt_switch_req ---------------------------------*/
+
+void rt_switch_req (P_TCB p_new) {
+ /* Switch to next task (identified by "p_new"). */
+ os_tsk.new = p_new;
+ p_new->state = RUNNING;
+ DBG_TASK_SWITCH(p_new->task_id);
+}
+
+
+/*--------------------------- rt_dispatch -----------------------------------*/
+
+void rt_dispatch (P_TCB next_TCB) {
+ /* Dispatch next task if any identified or dispatch highest ready task */
+ /* "next_TCB" identifies a task to run or has value NULL (=no next task) */
+ if (next_TCB == NULL) {
+ /* Running task was blocked: continue with highest ready task */
+ next_TCB = rt_get_first (&os_rdy);
+ rt_switch_req (next_TCB);
+ }
+ else {
+ /* Check which task continues */
+ if (next_TCB->prio > os_tsk.run->prio) {
+ /* preempt running task */
+ rt_put_rdy_first (os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_switch_req (next_TCB);
+ }
+ else {
+ /* put next task into ready list, no task switch takes place */
+ next_TCB->state = READY;
+ rt_put_prio (&os_rdy, next_TCB);
+ }
+ }
+}
+
+
+/*--------------------------- rt_block --------------------------------------*/
+
+void rt_block (U16 timeout, U8 block_state) {
+ /* Block running task and choose next ready task. */
+ /* "timeout" sets a time-out value or is 0xffff (=no time-out). */
+ /* "block_state" defines the appropriate task state */
+ P_TCB next_TCB;
+
+ if (timeout) {
+ if (timeout < 0xffff) {
+ rt_put_dly (os_tsk.run, timeout);
+ }
+ os_tsk.run->state = block_state;
+ next_TCB = rt_get_first (&os_rdy);
+ rt_switch_req (next_TCB);
+ }
+}
+
+
+/*--------------------------- rt_tsk_pass -----------------------------------*/
+
+void rt_tsk_pass (void) {
+ /* Allow tasks of same priority level to run cooperatively.*/
+ P_TCB p_new;
+
+ p_new = rt_get_same_rdy_prio();
+ if (p_new != NULL) {
+ rt_put_prio ((P_XCB)&os_rdy, os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_switch_req (p_new);
+ }
+}
+
+
+/*--------------------------- rt_tsk_self -----------------------------------*/
+
+OS_TID rt_tsk_self (void) {
+ /* Return own task identifier value. */
+ if (os_tsk.run == NULL) {
+ return (0);
+ }
+ return (os_tsk.run->task_id);
+}
+
+
+/*--------------------------- rt_tsk_prio -----------------------------------*/
+
+OS_RESULT rt_tsk_prio (OS_TID task_id, U8 new_prio) {
+ /* Change execution priority of a task to "new_prio". */
+ P_TCB p_task;
+
+ if (task_id == 0) {
+ /* Change execution priority of calling task. */
+ os_tsk.run->prio = new_prio;
+run:if (rt_rdy_prio() > new_prio) {
+ rt_put_prio (&os_rdy, os_tsk.run);
+ os_tsk.run->state = READY;
+ rt_dispatch (NULL);
+ }
+ return (OS_R_OK);
+ }
+
+ /* Find the task in the "os_active_TCB" array. */
+ if (task_id > os_maxtaskrun || os_active_TCB[task_id-1] == NULL) {
+ /* Task with "task_id" not found or not started. */
+ return (OS_R_NOK);
+ }
+ p_task = os_active_TCB[task_id-1];
+ p_task->prio = new_prio;
+ if (p_task == os_tsk.run) {
+ goto run;
+ }
+ rt_resort_prio (p_task);
+ if (p_task->state == READY) {
+ /* Task enqueued in a ready list. */
+ p_task = rt_get_first (&os_rdy);
+ rt_dispatch (p_task);
+ }
+ return (OS_R_OK);
+}
+
+/*--------------------------- rt_tsk_delete ---------------------------------*/
+
+OS_RESULT rt_tsk_delete (OS_TID task_id) {
+ /* Terminate the task identified with "task_id". */
+ P_TCB task_context;
+
+ if (task_id == 0 || task_id == os_tsk.run->task_id) {
+ /* Terminate itself. */
+ os_tsk.run->state = INACTIVE;
+ os_tsk.run->tsk_stack = rt_get_PSP ();
+ rt_stk_check ();
+ os_active_TCB[os_tsk.run->task_id-1] = NULL;
+
+ os_tsk.run->stack = NULL;
+ DBG_TASK_NOTIFY(os_tsk.run, __FALSE);
+ os_tsk.run = NULL;
+ rt_dispatch (NULL);
+ /* The program should never come to this point. */
+ }
+ else {
+ /* Find the task in the "os_active_TCB" array. */
+ if (task_id > os_maxtaskrun || os_active_TCB[task_id-1] == NULL) {
+ /* Task with "task_id" not found or not started. */
+ return (OS_R_NOK);
+ }
+ task_context = os_active_TCB[task_id-1];
+ rt_rmv_list (task_context);
+ rt_rmv_dly (task_context);
+ os_active_TCB[task_id-1] = NULL;
+
+ task_context->stack = NULL;
+ DBG_TASK_NOTIFY(task_context, __FALSE);
+ }
+ return (OS_R_OK);
+}
+
+
+/*--------------------------- rt_sys_init -----------------------------------*/
+void rt_sys_init (void) {
+ /* Initialize system and start up task declared with "first_task". */
+ U32 i;
+
+ DBG_INIT();
+
+ /* Initialize dynamic memory and task TCB pointers to NULL. */
+ for (i = 0; i < os_maxtaskrun; i++) {
+ os_active_TCB[i] = NULL;
+ }
+
+ /* Set up TCB of idle demon */
+ os_idle_TCB.task_id = 255;
+ os_idle_TCB.priv_stack = idle_task_stack_size;
+ os_idle_TCB.stack = idle_task_stack;
+ rt_init_context (&os_idle_TCB, 0, os_idle_demon);
+
+ /* Set up ready list: initially empty */
+ os_rdy.cb_type = HCB;
+ os_rdy.p_lnk = NULL;
+ /* Set up delay list: initially empty */
+ os_dly.cb_type = HCB;
+ os_dly.p_dlnk = NULL;
+ os_dly.p_blnk = NULL;
+ os_dly.delta_time = 0;
+
+ /* Fix SP and systemvariables to assume idle task is running */
+ /* Transform main program into idle task by assuming idle TCB */
+ os_tsk.run = &os_idle_TCB;
+ os_tsk.run->state = RUNNING;
+
+ /* Initialize ps queue */
+ os_psq->first = 0;
+ os_psq->last = 0;
+ os_psq->size = os_fifo_size;
+
+ rt_init_robin ();
+
+ /* Intitialize SVC and PendSV */
+ rt_svc_init ();
+}
+
+
+/*--------------------------- rt_sys_start ----------------------------------*/
+void rt_sys_start (void) {
+ /* Start system */
+
+ /* Intitialize and start system clock timer */
+ os_tick_irqn = os_tick_init ();
+ if (os_tick_irqn >= 0) {
+ OS_X_INIT(os_tick_irqn);
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Task.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,72 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_TASK.H + * Purpose: Task functions and system start up. + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Definitions */ + +/* Values for 'state' */ +#define INACTIVE 0 +#define READY 1 +#define RUNNING 2 +#define WAIT_DLY 3 +#define WAIT_ITV 4 +#define WAIT_OR 5 +#define WAIT_AND 6 +#define WAIT_SEM 7 +#define WAIT_MBX 8 +#define WAIT_MUT 9 + +/* Return codes */ +#define OS_R_TMO 0x01 +#define OS_R_EVT 0x02 +#define OS_R_SEM 0x03 +#define OS_R_MBX 0x04 +#define OS_R_MUT 0x05 + +#define OS_R_OK 0x00 +#define OS_R_NOK 0xff + +/* Variables */ +extern struct OS_TSK os_tsk; +extern struct OS_TCB os_idle_TCB; + +/* Functions */ +extern void rt_switch_req (P_TCB p_new); +extern void rt_dispatch (P_TCB next_TCB); +extern void rt_block (U16 timeout, U8 block_state); +extern void rt_tsk_pass (void); +extern OS_TID rt_tsk_self (void); +extern OS_RESULT rt_tsk_prio (OS_TID task_id, U8 new_prio); +extern OS_RESULT rt_tsk_delete (OS_TID task_id); +extern void rt_sys_init (void); +extern void rt_sys_start (void);
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_Time.c Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,94 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_TIME.C
+ * Purpose: Delay and interval wait functions
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+
+#include "rt_TypeDef.h"
+#include "RTX_Config.h"
+#include "rt_Task.h"
+#include "rt_Time.h"
+
+/*----------------------------------------------------------------------------
+ * Global Variables
+ *---------------------------------------------------------------------------*/
+
+/* Free running system tick counter */
+U32 os_time;
+
+
+/*----------------------------------------------------------------------------
+ * Functions
+ *---------------------------------------------------------------------------*/
+
+
+/*--------------------------- rt_time_get -----------------------------------*/
+
+U32 rt_time_get (void) {
+ /* Get system time tick */
+ return (os_time);
+}
+
+
+/*--------------------------- rt_dly_wait -----------------------------------*/
+
+void rt_dly_wait (U16 delay_time) {
+ /* Delay task by "delay_time" */
+ rt_block (delay_time, WAIT_DLY);
+}
+
+
+/*--------------------------- rt_itv_set ------------------------------------*/
+
+void rt_itv_set (U16 interval_time) {
+ /* Set interval length and define start of first interval */
+ os_tsk.run->interval_time = interval_time;
+ os_tsk.run->delta_time = interval_time + (U16)os_time;
+}
+
+
+/*--------------------------- rt_itv_wait -----------------------------------*/
+
+void rt_itv_wait (void) {
+ /* Wait for interval end and define start of next one */
+ U16 delta;
+
+ delta = os_tsk.run->delta_time - (U16)os_time;
+ os_tsk.run->delta_time += os_tsk.run->interval_time;
+ if ((delta & 0x8000) == 0) {
+ rt_block (delta, WAIT_ITV);
+ }
+}
+
+/*----------------------------------------------------------------------------
+ * end of file
+ *---------------------------------------------------------------------------*/
+
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-rtos/rtx/rt_Time.h Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,47 @@ +/*---------------------------------------------------------------------------- + * RL-ARM - RTX + *---------------------------------------------------------------------------- + * Name: RT_TIME.H + * Purpose: Delay and interval wait functions definitions + * Rev.: V4.50 + *---------------------------------------------------------------------------- + * + * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH + * All rights reserved. + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * - Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * - Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * - Neither the name of ARM nor the names of its contributors may be used + * to endorse or promote products derived from this software without + * specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + *---------------------------------------------------------------------------*/ + +/* Variables */ +extern U32 os_time; + +/* Functions */ +extern U32 rt_time_get (void); +extern void rt_dly_wait (U16 delay_time); +extern void rt_itv_set (U16 interval_time); +extern void rt_itv_wait (void); + +/*---------------------------------------------------------------------------- + * end of file + *---------------------------------------------------------------------------*/ +
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-rtos/rtx/rt_TypeDef.h Tue Mar 19 02:17:40 2013 +0000
@@ -0,0 +1,128 @@
+/*----------------------------------------------------------------------------
+ * RL-ARM - RTX
+ *----------------------------------------------------------------------------
+ * Name: RT_TYPEDEF.H
+ * Purpose: Type Definitions
+ * Rev.: V4.50
+ *----------------------------------------------------------------------------
+ *
+ * Copyright (c) 1999-2009 KEIL, 2009-2012 ARM Germany GmbH
+ * All rights reserved.
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * - Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * - Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * - Neither the name of ARM nor the names of its contributors may be used
+ * to endorse or promote products derived from this software without
+ * specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *---------------------------------------------------------------------------*/
+#ifndef RT_TYPE_DEF_H
+#define RT_TYPE_DEF_H
+
+#include "os_tcb.h"
+
+typedef U32 OS_TID;
+typedef void *OS_ID;
+typedef U32 OS_RESULT;
+
+#define TCB_STACKF 32 /* 'stack_frame' offset */
+#define TCB_TSTACK 36 /* 'tsk_stack' offset */
+
+typedef struct OS_PSFE { /* Post Service Fifo Entry */
+ void *id; /* Object Identification */
+ U32 arg; /* Object Argument */
+} *P_PSFE;
+
+typedef struct OS_PSQ { /* Post Service Queue */
+ U8 first; /* FIFO Head Index */
+ U8 last; /* FIFO Tail Index */
+ U8 count; /* Number of stored items in FIFO */
+ U8 size; /* FIFO Size */
+ struct OS_PSFE q[1]; /* FIFO Content */
+} *P_PSQ;
+
+typedef struct OS_TSK {
+ P_TCB run; /* Current running task */
+ P_TCB new; /* Scheduled task to run */
+} *P_TSK;
+
+typedef struct OS_ROBIN { /* Round Robin Control */
+ P_TCB task; /* Round Robin task */
+ U16 time; /* Round Robin switch time */
+ U16 tout; /* Round Robin timeout */
+} *P_ROBIN;
+
+typedef struct OS_XCB {
+ U8 cb_type; /* Control Block Type */
+ struct OS_TCB *p_lnk; /* Link pointer for ready/sem. wait list */
+ struct OS_TCB *p_rlnk; /* Link pointer for sem./mbx lst backwards */
+ struct OS_TCB *p_dlnk; /* Link pointer for delay list */
+ struct OS_TCB *p_blnk; /* Link pointer for delay list backwards */
+ U16 delta_time; /* Time until time out */
+} *P_XCB;
+
+typedef struct OS_MCB {
+ U8 cb_type; /* Control Block Type */
+ U8 state; /* State flag variable */
+ U8 isr_st; /* State flag variable for isr functions */
+ struct OS_TCB *p_lnk; /* Chain of tasks waiting for message */
+ U16 first; /* Index of the message list begin */
+ U16 last; /* Index of the message list end */
+ U16 count; /* Actual number of stored messages */
+ U16 size; /* Maximum number of stored messages */
+ void *msg[1]; /* FIFO for Message pointers 1st element */
+} *P_MCB;
+
+typedef struct OS_SCB {
+ U8 cb_type; /* Control Block Type */
+ U8 mask; /* Semaphore token mask */
+ U16 tokens; /* Semaphore tokens */
+ struct OS_TCB *p_lnk; /* Chain of tasks waiting for tokens */
+} *P_SCB;
+
+typedef struct OS_MUCB {
+ U8 cb_type; /* Control Block Type */
+ U8 prio; /* Owner task default priority */
+ U16 level; /* Call nesting level */
+ struct OS_TCB *p_lnk; /* Chain of tasks waiting for mutex */
+ struct OS_TCB *owner; /* Mutex owner task */
+} *P_MUCB;
+
+typedef struct OS_XTMR {
+ struct OS_TMR *next;
+ U16 tcnt;
+} *P_XTMR;
+
+typedef struct OS_TMR {
+ struct OS_TMR *next; /* Link pointer to Next timer */
+ U16 tcnt; /* Timer delay count */
+ U16 info; /* User defined call info */
+} *P_TMR;
+
+typedef struct OS_BM {
+ void *free; /* Pointer to first free memory block */
+ void *end; /* Pointer to memory block end */
+ U32 blk_size; /* Memory block size */
+} *P_BM;
+
+/* Definitions */
+#define __TRUE 1
+#define __FALSE 0
+#define NULL ((void *) 0)
+
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed.bld Tue Mar 19 02:17:40 2013 +0000 @@ -0,0 +1,1 @@ +http://mbed.org/users/mbed_official/code/mbed/builds/cd19af002ccc \ No newline at end of file