Igor Skochinsky / Mbed 2 deprecated DriverLibrary

NXP's driver library for LPC17xx, ported to mbed's online compiler. Not tested! I had to fix a lot of warings and found a couple of pretty obvious bugs, so the chances are there are more. Original: http://ics.nxp.com/support/documents/microcontrollers/zip/lpc17xx.cmsis.driver.library.zip

Dependencies:   mbed

Embed: (wiki syntax)

« Back to documentation index

lpc17xx_uart.c File Reference
Functions | Variables

lpc17xx_uart.c File Reference

: Contains all functions support for UART firmware library on LPC17xx More...

Go to the source code of this file.

Functions

uint8_t getUartNum (LPC_UART_TypeDef *UARTx)
 Get UART number due to UART peripheral pointer.
Status uart_set_divisors (LPC_UART_TypeDef *UARTx, uint32_t baudrate)
 Determines best dividers to get a target clock rate.
void UART_GenIntHandler (LPC_UART_TypeDef *UARTx)
 General UART interrupt handler and router.
void UART_DeInit (LPC_UART_TypeDef *UARTx)
 De-initializes the UARTx peripheral registers to their default reset values.
void UART_Init (LPC_UART_TypeDef *UARTx, UART_CFG_Type *UART_ConfigStruct)
 Initializes the UARTx peripheral according to the specified parameters in the UART_ConfigStruct.
void UART_ConfigStructInit (UART_CFG_Type *UART_InitStruct)
 Fills each UART_InitStruct member with its default value: 9600 bps 8-bit data 1 Stopbit None Parity.
void UART_SendData (LPC_UART_TypeDef *UARTx, uint8_t Data)
 Transmit a single data through UART peripheral.
uint8_t UART_ReceiveData (LPC_UART_TypeDef *UARTx)
 Receive a single data from UART peripheral.
void UART_ForceBreak (LPC_UART_TypeDef *UARTx)
 Force BREAK character on UART line, output pin UARTx TXD is forced to logic 0.
void UART_IrDAInvtInputCmd (LPC_UART_TypeDef *UARTx, FunctionalState NewState)
 Enable or disable inverting serial input function of IrDA on UART peripheral.
void UART_IrDACmd (LPC_UART_TypeDef *UARTx, FunctionalState NewState)
 Enable or disable IrDA function on UART peripheral.
void UART_IrDAPulseDivConfig (LPC_UART_TypeDef *UARTx, UART_IrDA_PULSE_Type PulseDiv)
 Configure Pulse divider for IrDA function on UART peripheral.
void UART_IntConfig (LPC_UART_TypeDef *UARTx, UART_INT_Type UARTIntCfg, FunctionalState NewState)
 Enable or disable specified UART interrupt.
uint8_t UART_GetLineStatus (LPC_UART_TypeDef *UARTx)
 Get current value of Line Status register in UART peripheral.
FlagStatus UART_CheckBusy (LPC_UART_TypeDef *UARTx)
 Check whether if UART is busy or not.
void UART_FIFOConfig (LPC_UART_TypeDef *UARTx, UART_FIFO_CFG_Type *FIFOCfg)
 Configure FIFO function on selected UART peripheral.
void UART_FIFOConfigStructInit (UART_FIFO_CFG_Type *UART_FIFOInitStruct)
 Fills each UART_FIFOInitStruct member with its default value:

  • FIFO_DMAMode = DISABLE
  • FIFO_Level = UART_FIFO_TRGLEV0
  • FIFO_ResetRxBuf = ENABLE
  • FIFO_ResetTxBuf = ENABLE
  • FIFO_State = ENABLE.

void UART_ABCmd (LPC_UART_TypeDef *UARTx, UART_AB_CFG_Type *ABConfigStruct,\FunctionalState NewState)
 Start/Stop Auto Baudrate activity.
void UART_TxCmd (LPC_UART_TypeDef *UARTx, FunctionalState NewState)
 Enable/Disable transmission on UART TxD pin.
void UART_FullModemForcePinState (LPC_UART1_TypeDef *UARTx, UART_MODEM_PIN_Type Pin,\UART1_SignalState NewState)
 Force pin DTR/RTS corresponding to given state (Full modem mode)
void UART_FullModemConfigMode (LPC_UART1_TypeDef *UARTx, UART_MODEM_MODE_Type Mode,\FunctionalState NewState)
 Configure Full Modem mode for UART peripheral.
uint8_t UART_FullModemGetStatus (LPC_UART1_TypeDef *UARTx)
 Get current status of modem status register.
void UART_RS485Config (LPC_UART1_TypeDef *UARTx, UART1_RS485_CTRLCFG_Type *RS485ConfigStruct)
 Configure UART peripheral in RS485 mode according to the specified parameters in the RS485ConfigStruct.
void UART_RS485ReceiverCmd (LPC_UART1_TypeDef *UARTx, FunctionalState NewState)
 Enable/Disable receiver in RS485 module in UART1.
uint32_t UART_RS485Send (LPC_UART1_TypeDef *UARTx, uint8_t *pDatFrm,\uint32_t size, uint8_t ParityStick)
 Send data on RS485 bus with specified parity stick value (9-bit mode).
void UART_RS485SendSlvAddr (LPC_UART1_TypeDef *UARTx, uint8_t SlvAddr)
 Send Slave address frames on RS485 bus.
uint32_t UART_RS485SendData (LPC_UART1_TypeDef *UARTx, uint8_t *pData, uint32_t size)
 Send Data frames on RS485 bus.
uint32_t UART_Send (LPC_UART_TypeDef *UARTx, uint8_t *txbuf, uint32_t buflen, TRANSFER_BLOCK_Type flag)
 Send a block of data via UART peripheral.
uint32_t UART_Receive (LPC_UART_TypeDef *UARTx, uint8_t *rxbuf,\uint32_t buflen, TRANSFER_BLOCK_Type flag)
 Receive a block of data via UART peripheral.
void UART_SetupCbs (LPC_UART_TypeDef *UARTx, uint8_t CbType, void *pfnCbs)
 Setup call-back function for UART interrupt handler for each UART peripheral.
void UART0_StdIntHandler (void)
 Standard UART0 interrupt handler.
void UART1_StdIntHandler (void)
 Standard UART1 interrupt handler.
void UART2_StdIntHandler (void)
 Standard UART2 interrupt handler.
void UART3_StdIntHandler (void)
 Standard UART3 interrupt handler.

Variables

UART_CBS_Type uartCbsDat [4]
 Call-back function pointer data.
fnModemCbs_Type * pfnModemCbs = NULL
 UART1 modem status interrupt callback pointer data.

Detailed Description

: Contains all functions support for UART firmware library on LPC17xx

Version:
: 1.0
Date:
: 18. Mar. 2009
Author:
: HieuNguyen

Software that is described herein is for illustrative purposes only which provides customers with programming information regarding the products. This software is supplied "AS IS" without any warranties. NXP Semiconductors assumes no responsibility or liability for the use of the software, conveys no license or title under any patent, copyright, or mask work right to the product. NXP Semiconductors reserves the right to make changes in the software without notification. NXP Semiconductors also make no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Definition in file lpc17xx_uart.c.

Generated on Tue Jul 12 2022 17:06:02 by  doxygen 1.7.2